Transcript
Quick Rack™ QMQR-EF - Enphase Mount Assembly
RESPECT THE ROOF
BI 7.2.3-28_1
Sep-2014, Rev A
Quick Rack Enphase Mount Installation Instructions Installation Tools Required: wire clips, 1/2" socket wrench.
1 In a standard landscape array, the Enphase inverter bracket will be installed approximately 7" in from the edge of the module. The AC connector harness will be installed about 12" from the corner of the module.
4 Slide the entire unit up under the bracket clamp, and then slightly to the left so that the cap screw holds everything together.
7
2 Place the bracket clamp over the edge of the module frame.
5 Tighten the cap screw with a half-inch socket wrench to a torque of 13 foot-pounds.
3 With the cap screw threaded into the channel on the bracket, slide the Enphase inverter on top of the bracket with the cap screw in the middle channel on the inverter.
6 Neatly coil the wires and clip to module frame.
8
Clip the AC connector harness to edge of the Clip the trunk cable where it dips to the underside module frame. Connect the trunk cable to the of the module frame using wire clips. Enphase AC inverter cable, and clip the trunk cable into the harness when on the roof. BI 7.2.3-28_1
Sep-2014, Rev A
ITEM NO.
DESCRIPTION
QTY./BOX
1
QR ENPHASE BRACKET, FLAT LID, 5052-H32, MILL
1
2
QR ENPHASE BRACKET CLAMP, 35MM, 5005-H34, BRONZE
1
3
CAP SCREW, SERRATED FLANGE, HEX HEAD, 5/16"-18 X 3/4", UNC-2A, 18-8SS
1
4
QR ENPHASE AC CONNECTOR HARNESS, 5052-H32, MILL
1
2 1
ITEM 2: AVAILABLE IN 35MM AND 40MM VERISONS
4 3
TITLE:
QMQR-EF: QUICK RACK, ENPHASE MOUNT ASSEMBLY, FLAT LID
UNLESS OTHERWISE SPECIFIED:
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF QUICK MOUNT PV. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF QUICK MOUNT PV IS PROHIBITED.
4
5
DO NOT SCALE DRAWING
MODULE FRAME
DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/8 TWO PLACE DECIMAL .18 THREE PLACE DECIMAL .125
SIZE
A
DRAWN BY: DATE:
SCALE: 1:2
WEIGHT: 0.3800
2
3
DFM
8/11/2014
REV
-.G SHEET 1 OF 2
1
BRACKET
BRACKET CLAMP
INVERTER
CAP SCREW MODULE FRAME
MODULE FRAME
AC CONNECTOR HARNESS
INVERTOR CONNECTOR
INVERTOR CONNECTOR
AC CABLE CONNECTOR
AC CABLE CONNECTOR AC CONNECTOR HARNESS ORIENTATION-2
ORIENTATION-1
TITLE:
QMQR-EF: QUICK RACK, ENPHASE MOUNT ASSEMBLY, FLAT LID
UNLESS OTHERWISE SPECIFIED:
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF QUICK MOUNT PV. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF QUICK MOUNT PV IS PROHIBITED.
5
BI 7.2.3-28_1
4
DO NOT SCALE DRAWING
3
DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/8 TWO PLACE DECIMAL .18 THREE PLACE DECIMAL .125
2
SIZE
A
DRAWN BY: DATE:
SCALE: 1:2
DFM
8/11/2014
WEIGHT: 0.3800
REV
-.G SHEET 2 OF 2
1
Sep-2014, Rev A
RESPECT THE ROOF
925-478-8269 www.quickmountpv.com
[email protected] 2700 Mitchell Dr., Bldg 2 Walnut Creek, CA 94598 © 2014 by Quick Mount PV. All rights reserved.
