Transcript
ETXexpress Eval2 Carrier Board (PN: 38104-0000-00-0)
Quick Reference
ETXe Eval2 Carrier Board Layout:
Overview:
In this Quick Reference guide, Kontron provides a brief description of the ETXexpress Eval2 carrier board. This document is intended as a reference to be used along with the Kontron Design Guide for COM Express carrier boards as well as the appropriate manual for the COM Express compliant or COM Express compatible module that you are using. This evaluation carrier board is designed and tested to work with all of Kontron’s COM Express modules that follow the Type 1 and 2 pin-outs. In addition to using this carrier board with the COM Express “Basic” form factor ETXexpress modules that Kontron offers, this carrier board also is approved for use with the Kontron microETXexpress line of “compact” form factor COM Express compatible (following COM.0 pin-out type 2) modules. In this guide we provide you with an overview of the connectors on the carrier board as well as a their pinouts. Additionally we provide you with the jumper settings and locations. For your convenience, much of this information also is silk-screened on the carrier board itself. For any assistance, please contact Kontron’s technical support teams --> www.kontron.com
I/O Connector Overview: Description
Connector
PS2 Mouse (top) and Keyboard (bottom)
J47
COM2 (top) VGA out (bottom)
J49
COM1 (10-pin header)
J40
USB - USB4 (top), USB5 (bottom)
J46
USB - USB2 (top), USB0 (2nd J48 from top), USB1(3rd from top), USB3 (bottom)
Note: Large holes around the edges of the carrier represent the mechanical mounting holes compliant to the ATX board standard for deploying the carrier in a standard ATX chassis. Smaller circles around the silkscreened “Basic Module” and “Compact Module” area represent the mounting holes required by the PICMG COM Express(TM) standard. Additional HDA Connector Information: There are various color coding schemes for audio connectors. Kontron has selected the color scheme detailed in the table to the right for the HDA connector on this reference design carrier board:
Ethernet
J50
S-Video Connector
J53
HD Audio Connector
J51
Ethernet Settings - 10/100 vs. 10/100/1000: Each COM Express module supports either 10/ 100 or 10/100/1000 Ethernet. If you are using a modules with 10/100 LAN, DO NOT load J41/ J42, all that is required for this 10/100 LAN is the default J50. If you are using a module that supports 10/100/1000 Ethernet, DO load J41/J42. Color
Position
Desc.
Blue
Top Left
Mid-Surround Line Out
Orange
Top Right
Center Speaker/Subwoofer Line Out
Greem
Middle Left
Line In (Stereo)
Black
Middle Right
Rear-Surround Line Out
Pink
Bottom Left
Mic-in (Mono)
Grey
Bottom Right
Line out/Front Speaker/ Headphone Page 1 of 2
Kontron ETXexpress Eval2 Carrier Board Layout:
IDE 44-pin ATX Power pin1 Compact Flash
6x USB Ethernet Audio mini-PCI
Express Card
LVDS mini-PCIe non-standard
COM Express
SATA PEG x16
PCI
Power
Reset
BIOS Socket Programming Header
Parallel Header
Serial Header PCI Express x1
Audio Header Page 2 of 2
Copyright © 2008 Kontron All data is for information purposes only and not guaranteed for legal purposes. Subject to change without notice. Information in this quick reference guide has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccurancies. All rights reserved. DIMM-PC®, PISA®, ETX®, ETXexpress® and X-board® are trademarks or registered trademarks of Kontron Embedded Modules GmbH. Kontron is trademark or registered trademark of Kontron AG. All other brand or product names are trademarks or registered trademarks or copyrights by their respective owners and are recognized.
mini-PCIe 1.1 compliant
