Transcript
Quick Start Guide ESUL8P-PC2-D* / ESML8P-PC2-D* Introduction Welcome to KBC Network’s Quick Start Guide for the ESUL8P-PC2 and ESML8P-PC2, 10-port, PoE switches. This document provides some quick tips on how to get up and running. For more detailed information see the Downloads section below.
Industrial Ethernet Switch System Contents
Equipment Required for Physical Deployment
Qty Description 1
Ethernet switch fitted with DIN rail mount.
2
Wall-mount brackets with screws.
1
Pluggable terminal block.
You will need a 48Vdc power supply, these are supplied separately.
Features: • • • • • •
IEEE802.3af on 8 ports Dual redundant power input Alarm output for power supply Full & half duplex operation MDI/MDI-X IP30 casing
Downloads Installation manuals & specification sheets: Other features and functions are described in the unabridged manuals and specification sheets:
Unmanaged switch: http://www.kbcnetworks.com/esul8p-pc2series/network-products/esul8p-pc2-series
Managed switch: http://www.kbcnetworks.com/esml8p-pc2switch-poe/network-products/esml8p-pc2-series
QSG_ESUL8P-ESML8P-PC2-Rev1211 Copyright © KBC Networks Ltd. 2012
www.kbcnetworks.com
Quick Start Guide
Industrial Ethernet Switch
ESUL8P-PC2-D* / ESUL8P-PC2-D*
ESUL8P-PC2-D* / ESML8P-PC2-D* LED Status Indicators Ethernet RJ45 Ports P9 & P10 Status LED
Configuring the ESUL8P-PC2-D* / ESML8P-PC2-D*
LED PWR1
1. 2. 3.
Connect the DIN rail or wall-mount brackets as required. Connect a 48Vdc power supply, (supplied separately). If using only one power source, connect pin 1 to pin 5 and pin 2 to pin 6 otherwise the Power Fail LED will be lit.
PWR2 P-Fail
PoE 1-8
ON
Power is supplied to the unit
Each RJ45 Ethernet port has two green indicators. The yellow lamp indicates port speed, and the green lamp indicates port link state.
OFF
No power to the unit
Lower LED
Status
Description
ON
Power is supplied to the unit
OFF
No power to the unit
OFF
ON
Power to PWR1 or PWR2 has failed
OFF
Power is functioning to both or none of the power inputs.
ON
The port is supplying power to the powered device.
FLASH
OFF
There is no powered device attached or the power to the device has failed
OFF
Upper LED
Link/Active
Ethernet RJ45 Port P1 – P8 Status LED 4. 5. 6.
Install SFP modules as required. Link external devices to the switch with appropriate cables. Connect the fault alarm contact if required.
Each RJ45 Ethernet port has two indicators. The yellow lamp indicates port speed, and the green lamp indicates port link state. Lower
P-Fail
Upper
OFF
Effective network connection has been established for the port
ON
Data traffic is passing through the port
No effective network connection has been established for the port ON SFP port link established FLASH Active data flow OFF
No connection to the network
FLASH Collisions are occurring
Need Help?
ON
Half duplex link or no connection
OFF
Effective network connection has been established for the port
Visit our website http://www.kbcnetworks.com or contact your nearest KBC office or dealer:
ON
No effective network connection has been established for the port
USA: Phone: +1 949-297-4930 Toll Free: +1 888-366-4276 Email:
[email protected] EMEA: Phone: +44(0)1622 618787 Email:
[email protected]
24Vdc, 1A resistance
QSG-ESUL8P-ESML8P-PC2-Rev1211 Copyright © KBC Networks Ltd. 2012
Port not operating at 1000M or no connection
Full duplex link
FLASH Data traffic is passing through the port
Load
Power is supplied to the unit
ON
External power
APAC: Phone: +65 98463323 Email:
[email protected]
www.kbcnetworks.com
