Transcript
What’s in the box
VM344-2 baby monitor system
VM344-2
Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news.
Baby’s room
Living room
Quick start guide
1
2
Connect and power on - Baby unit
3
Install the battery
THIS SIDE UP
Status check Once you power on your baby monitor, your parent unit displays image from baby unit light turns on.
1
2
, and the LINK LED
6
1
2
2
4
Connect and power on - Parent unit
63ē
3
1
2s
6U]KXOTMUT
1
2
2
63ē
6U]KXOTMUT
1
63ē
Morethan than 11meter More meter (3 feet) (3 feet)
The ON/OFF LED light of baby unit
turns on. As baby unit
is not being viewed, its ON/OFF LED light flashes.
More than 1 meter (3 feet)
CAUTION
•
Change different views - View
Change different views - Patrol
Press VIEW to switch between the image of baby units
and
.
To prevent high-pitched screeching noise from your baby monitor: - Make sure your baby units and parent unit are more than 1 meter (3 feet) apart. - Turn down the volume of your parent unit before caring for your baby.
Change different views - Split
Press PATROL to alternately view the image from baby units
and
every 10 seconds.
Press SPLIT to view the images from all baby units at once.
Dim mode With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy. • Press any button on your parent unit to restore screen brightness.
10 min inactivity
Press VIEW
10s
Overview - Parent unit
Overview - Baby unit
Light indicators
Microphone
At least 1 meter (3 feet)
Zoom
On/off
TALK + / VOL / -
Antenna
Infrared LEDs
VIEW / LCD ON/OFF
MENU/SELECT
Speaker
Light sensor
Antenna
Speaker
Camera
PATROL
Temperature sensor
SPLIT
Arrow keys
Stand
ON/OFF switch Microphone
ON/OFF light
+ / VOL / -
Basic operation - Parent unit
Basic operation - Baby unit
Adjust speaker volume
Pan, tilt, zoom
Press + / VOL / - to adjust your parent unit speaker volume.
Press and hold
,
,
or
to move the camera.
Talk
Turn off the screen
Use the menu
Turn off the parent unit
Adjust speaker volume
Turn off the baby unit
Press and hold TALK to talk to the baby unit.
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the selected baby unit.
Press MENU/SELECT to enter the menu, choose a menu item, or save a setting.
Press and hold
Press + / VOL / - to adjust your baby unit speaker volume.
Slide the ON/OFF switch to the right to power off your baby unit.
to power off your parent unit.
While in the menu:
63ē
• Press or to scroll up or down. • Press to select an item, or save a setting. • Press BACK to return to the main menu or idle screen.
63ē
63ē
63ē
63ē
Press
LCD is turning off...
63ē
2s 6U]KXOTMULL
Alert Tone
Long press
to zoom in or out.
2s
6U]KXOTMULL
Alert Tone
6U]KXOTMUT
Low Bettery Tone
Low Bettery e No Link Ton Alert 63ē
Sound alert in split-v
No Link Alert
63ē
iew
Sound alert in split-v
iew
63ē
Sound activation Automatically turns on the parent unit screen when the baby unit being viewed detects a sound after the screen is turned off. When no sound is detected within 50 seconds, the screen is automatically turned off to save power.
Night vision
Mount the baby monitor (optional)
Sound-activated Screen
On Off
The baby unit has infrared LEDs that allow you to see your baby at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs turn on automatically.
3
NOTES
•
•
TIP
•
1
It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment. When the infrared LEDs are on, the image is in black and white. This is normal due to external light sources. Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle, or place the baby unit at a higher level to prevent glare and blurry display.
1 2
NOTES
•
Check for reception strength and camera angle before drilling the holes.
Place the wall mount on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount and drill two holes in the wall (7/32” drill bit).
If you drill the holes into a stud, go to step 3. -ORIf you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.
Align the wall mount and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount position is fixed. You can tighten the other screw in the top hole.
Place the baby unit on the wall mount. Tighten the screw into the threaded socket at the bottom to secure the baby unit.
2
OR Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.
Place the baby unit on the wall mount. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount with the screws on the wall, and slide the wall mount down until it locks into place.
Specifications are subject to change without notice. © 2015 VTech Communications, Inc. All rights reserved. 12/15. VM344-2_QSG_V3.0. Document order number: 96-011018-020-100
