Transcript
Clean With Scooba With the Clean tank filled and properly installed, place Scooba in the center of the room, press “Power” and then press “Clean.” Scooba will begin a cleaning cycle. Let Scooba clean until the tank is empty (approximately 45 minutes). Scooba’s “Clean” button will display the following: Clean Button Light Green Blue/Green pulse Solid blue
What it means Cleaning Almost complete Complete
Empty Scooba
When Scooba has completed a cleaning cycle, empty and rinse Scooba’s tanks.
2
1
Remove Scooba’s tank.
Open the Dirty and Clean tanks and drain.
5
4
Remove and rinse Scooba’s filter.
Remove and clean Scooba's cleaning head and brush.
3
Quick Start Guide An easy step-by-step guide to using the iRobot Scooba
Rinse the Dirty and Clean tanks with warm water.
6
Replace Scooba’s tank.
See the Owner’s Manual for important tips and maintenance instructions, or visit www.irobot.com www.irobot.com © 2006 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reserved. iRobot is a registered trademark of iRobot Corporation. Scooba is a trademark of iRobot Corporation. US Pat. Nos. 6,690,134 | 6,809,490 | 6,594,844. Other patents pending. Clorox is a registered trademark of The Clorox Company. All rights reserved.
Before You Get Started
Understand how iRobot Scooba cleans
Scooba’s Cleaning Pattern
Scooba’s Cleaning System
Scooba is a robot that cleans differently than the way most people clean their floors. Scooba uses iRobot’s AWARE™ Robot Intelligence System to determine the best way to pass over and clean every section of the floor.
Scooba performs 4 cleaning methods in one pass:
3
3
3
Place battery in Scooba by rotating the battery into its slot, making sure the yellow tabs fit inside the guide holes.
Preps – Picks up loose crumbs, sand, and dirt Washes – Uses fresh, clean solution Scrubs – Gently scrubs your floor, removing dirt, grime, and spills
While Scooba is cleaning, it calculates the best path to clean your floor and it determines the best times to exhibit its various cleaning behaviors:
Dries – Picks up the dirty solution, leaving the floor clean and dry*
Spiraling: Enables Scooba to efficiently clean a concentrated dirty area Wall following: Enables Scooba to clean the room perimeter and navigate around furniture and obstacles
4 Plug the Power Supply into Scooba to charge the battery. For best performance, iRobot recommends charging Scooba's battery overnight the first time only.
Power Button Light Red Green pulse Green fast pulse Solid Green Blinking Red
Battery Status Battery empty Charging 16-hour refresh charge Fully charged Battery not installed
Fill Scooba’s Tank 2
1
Room crossing: Enables Scooba to clean new areas while crisscrossing the room
3
IMPORTANT: Let Scooba complete an entire cleaning cycle every time you clean
SINK
TABLE
STOVE
START
Internal Dry Mode
At the end of the cleaning cycle, Scooba will enter a brief internal drying mode to remove any liquid remaining on its brushes and inside its cleaning mechanisms. During this time Scooba’s Clean light will blink blue.
Open Scooba’s tank.
Lift the tank clear of the robot and place the tank on a flat surface.
Using the included measuring cup, measure and pour Clorox® Scooba cleaning solution into the Clean tank.
FRIDGE
4 Scooba’s Cleaning Pattern
5
6
* Floor drying time may vary.
Charge Scooba’s Battery 2
1 Release Scooba’s tank by pushing the handle.
Grasp the handle and pull Scooba’s tank up.
Slowly fill the remainder of the Clean Secure the tank cap and place tank with warm or cold tap water. Tilt the tank back in the tank holder. the tank and ensure it is completely filled to the top.
Close the tank by pressing down on the tank. You will hear a click when the tank is properly installed.
Use of plain tap water or extremely small amounts of cleaning solution reduces Scooba’s ability to recognize water in the Clean tank. Always use the recommended amount of cleaning solution and water.
Instructional videos available at www.irobot.com/usetips
Instructional videos available at www.irobot.com/usetips
Before You Get Started
Understand how iRobot Scooba cleans
Scooba’s Cleaning Pattern
Scooba’s Cleaning System
Scooba is a robot that cleans differently than the way most people clean their floors. Scooba uses iRobot’s AWARE™ Robot Intelligence System to determine the best way to pass over and clean every section of the floor.
Scooba performs 4 cleaning methods in one pass:
3
3
3
Place battery in Scooba by rotating the battery into its slot, making sure the yellow tabs fit inside the guide holes.
Preps – Picks up loose crumbs, sand, and dirt Washes – Uses fresh, clean solution Scrubs – Gently scrubs your floor, removing dirt, grime, and spills
While Scooba is cleaning, it calculates the best path to clean your floor and it determines the best times to exhibit its various cleaning behaviors:
Dries – Picks up the dirty solution, leaving the floor clean and dry*
Spiraling: Enables Scooba to efficiently clean a concentrated dirty area Wall following: Enables Scooba to clean the room perimeter and navigate around furniture and obstacles
4 Plug the Power Supply into Scooba to charge the battery. For best performance, iRobot recommends charging Scooba's battery overnight the first time only.
Power Button Light Red Green pulse Green fast pulse Solid Green Blinking Red
Battery Status Battery empty Charging 16-hour refresh charge Fully charged Battery not installed
Fill Scooba’s Tank 2
1
Room crossing: Enables Scooba to clean new areas while crisscrossing the room
3
IMPORTANT: Let Scooba complete an entire cleaning cycle every time you clean
SINK
TABLE
STOVE
START
Internal Dry Mode
At the end of the cleaning cycle, Scooba will enter a brief internal drying mode to remove any liquid remaining on its brushes and inside its cleaning mechanisms. During this time Scooba’s Clean light will blink blue.
Open Scooba’s tank.
Lift the tank clear of the robot and place the tank on a flat surface.
Using the included measuring cup, measure and pour Clorox® Scooba cleaning solution into the Clean tank.
FRIDGE
4 Scooba’s Cleaning Pattern
5
6
* Floor drying time may vary.
Charge Scooba’s Battery 2
1 Release Scooba’s tank by pushing the handle.
Grasp the handle and pull Scooba’s tank up.
Slowly fill the remainder of the Clean Secure the tank cap and place tank with warm or cold tap water. Tilt the tank back in the tank holder. the tank and ensure it is completely filled to the top.
Close the tank by pressing down on the tank. You will hear a click when the tank is properly installed.
Use of plain tap water or extremely small amounts of cleaning solution reduces Scooba’s ability to recognize water in the Clean tank. Always use the recommended amount of cleaning solution and water.
Instructional videos available at www.irobot.com/usetips
Instructional videos available at www.irobot.com/usetips
Clean With Scooba With the Clean tank filled and properly installed, place Scooba in the center of the room, press “Power” and then press “Clean.” Scooba will begin a cleaning cycle. Let Scooba clean until the tank is empty (approximately 45 minutes). Scooba’s “Clean” button will display the following: Clean Button Light Green Blue/Green pulse Solid blue
What it means Cleaning Almost complete Complete
Empty Scooba
When Scooba has completed a cleaning cycle, empty and rinse Scooba’s tanks.
2
1
Remove Scooba’s tank.
Open the Dirty and Clean tanks and drain.
5
4
Remove and rinse Scooba’s filter.
Remove and clean Scooba's cleaning head and brush.
3
Quick Start Guide An easy step-by-step guide to using the iRobot Scooba
Rinse the Dirty and Clean tanks with warm water.
6
Replace Scooba’s tank.
See the Owner’s Manual for important tips and maintenance instructions, or visit www.irobot.com www.irobot.com © 2006 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reserved. iRobot is a registered trademark of iRobot Corporation. Scooba is a trademark of iRobot Corporation. US Pat. Nos. 6,690,134 | 6,809,490 | 6,594,844. Other patents pending. Clorox is a registered trademark of The Clorox Company. All rights reserved.
