Transcript
Key Features – – – – – – – – –
HDMI 1.4 (1080P) to H.264 encoder and decoder Supports one pair of HDMI embedded audio Supports both Unicast and Multicast Supports up to 1080P@60Hz at 18Mbps Supports point to point up to 100 meters Compatible with CAT 5/E/6 cables Supports RS-232 HDMI and HDCP compliant Web interface for basic configuration
Front/Rear View
HDMI-IP-E (Encoder)
1. 2. 3. 4.
HDMI Loop out. (YCbCr 4:4:4) HDMI Input Multicast ID DIP Switch Power (12 V DC 2A)
1. 2. 3. 4. 5. 6.
LED power indicator System reset Baud rate setting DIP Switch IR out RS-232 LINK
Specifications
HDMI-IP-E and HDMI-IP-R
QUICK START GUIDE Visit www.apantac.com for the full Manual
(H.264 Encoder / Decoder SET)
What’s in the Box Note: HDMI-IP-E and HDMI-IP-R can also be sold separately 1 1 2 2 1
x x x x x
HDMI-IP-E (Encoder) HDMI-IP-R (Decoder) IR Emitter Cable 12V DC Power supplies Quick START Guide
© 2016 APANTAC LLC, All rights reserved 7470 SW BRIDGEPORT ROAD PORTLAND, OR 97224, USA PHONE +1 503 968 3000, FAX +1 503 389 7921 The content of this document are provided in connection with Apantac LLC (“Apantac”) products. Apantac makes no representation or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions
Functions/Part# HDMI Input Connector HDMI Input Color Space
HDMI Output Connector HDMI Output Color Space HDMI Output Max. Resolution LED Indicators LINK IR In IR Out IR Carrier Frequency Baud Rate Settings ID DIP Switch CAT 5E cable distance RS-232 connector Baud Rate
Weight Dimension (LxW-H)
HDMI-IP-E HDMI-IP-R 1 (HDMI None Type A) HDMI: RGB 8/10/12 bit, YCbCr 4:2:2/4:4:4 8/10/12 bit, DVI:RGB/YCbCr 4:2:2/4:4:4 8 bit 1 (HDMI Type A) YCbCr RGB 4:4:4 1080P@60Hz (8 bit) Power Rj-45 None 3.5 mm jack 3.5 mm None jack 20KHz ~ 60KHz 3 PIN DIP Switch 8 PIN DIP Switch 100 meters maximum DB9 Female 2400 up to 115,200 bps; data bits, 1 stop bit, no parity 338 g 120x75x33 mm
HDMI-IP-R(Decoder)
1. HDMI Output 2. Multicast ID DIP Switch 3. Power (12 V DC 2A)
1. 2. 3. 4. 5. 6.
LED power indicator System reset Baud rate setting DIP Switch IR out RS-232 LINK
7. Connect the powers to both HDMI-IP-E’s and all the HDMI-IP-R’s 8. Turn on the the powers for the HDMI Displays
Supported Resolutions Resolution 640x480 800x600 1024x768 1280x768 1280x800 1280x960 1280x1024 1360x768 1366x768 1440x900 1400x1050 1440x1050 1600x900 1680x1050 480i 480p 576i 576p 1080i 1080p 720p
Frequency(Hz) 60 60 60 60 60 60 60 60 60 60 60 60 60 60 59.94/60 59.94/60 50 50 50/59.94/60 23.98/24/25/29.98/30/50/59.94/60 50/59.94/60
Point to Multi-point connection
1. Turn off the HDMI source and HDMI Display 2. Connect the cable between the source and the HDMI-IP-E via the HDMI in port 3. Connect the HDMI cables between the Displasy and the HDMi-IP-E and HDMI-IP-R 4. Connect the CATx cables between the HDMIIP-E and the switch 5. Connect the CATx cables between the HDMIIP-R and the switch 6. Make sure the ID DIP Switch is set the same 7. Connect the powers to both HDMI-IP-E and all the HDMI-IP-R’s 8. Turn on the the power for the HDMI Displays
DIP Switches Baud Rate 2400 4800 9600 19200 28800 38400 57600 115200
PIN 1 OFF ON OFF ON OFF ON OFF ON
PIN 2 OFF OFF ON ON OFF OFF ON ON
PIN3 OFF OFF OFF OFF ON ON ON ON
Point to point connection 1. 2. 3. 4. 5. 6. 7.
Turn off the HDMI source and HDMI Display Connect the cable between the source and the HDMI-IP-E via the HDMI in port Connect the HDMI cables between the Displasy and the HDMi-IP-E and HDMI-IP-R Connect the CATx cable between the HDMIIP-E and HDMI-IP-R Make sure the ID DIP Switch is set the same Connect the power to both HDMI-IP-E and HDMI-IP-R Turn on the the power for the HDMI Displays
Multiple transmitters to multiple receivers
1. Turn off the HDMI sources and HDMI Display 2. Connect the cable between the sources and all the HDMI-IP-E via their HDMI in ports 3. Connect the HDMI cables between the Display and all the HDMi-IP-E’s and HDMI-IP-R’s 4. Connect the CATx cables between all the HDMI-IP-E’s and the switch 5. Connect the CATx cables between all the HDMI-IP-R’s and the switch 6. Make sure the ID DIP Switch is set the same
PIN1
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
OFF OFF : ON
OFF OFF : ON
OFF OFF : :
OFF OFF : :
OFF OFF : :
Not Used
7
OFF ON : ON
: 63
: ON
: ON
: ON
: ON
: ON
: ON
Reset OFF Wait 3 Sec. ON
ID 0 1
