Transcript
Quick Start Guide
SABRE Platform for Automotive Infotainment Based on the i.MX 6Quad or 6DualLite Applications Processors
Quick Start Guide ABOUT SABRE PLATFORM FOR AUTOMOTIVE INFOTAINMENT BASED ON THE i.MX 6QUAD OR 6DUALLITE APPLICATIONS PROCESSORS The Smart Application Blueprint for Rapid Engineering (SABRE) platform for automotive infotainment offers a solid foundation for nextgeneration infotainment, instrument cluster, telematics or rear seat entertainment designs. The i.MX 6 series of applications processors represents a scalable family of products powered by single-, dual- and quadcore implementations of the ARM® Cortex®-A9 core for the automotive market. With multicore processing speeds of up to 1 GHz as well as a high level of integration, the SABRE platform for automotive infotainment enables customers to recreate today’s consumer user experiences in the car.
1 GHz i.MX 6Quad applications processor or 800 MHz i.MX 6DualLite applications processor
The following features are available with the SABRE platform for automotive infotainment CPU card:
Broadcom® BroadR-Reach® Ethernet PHY or Switch (ordered separately) for automotive AVB support
i.MX 6Quad applications processor: 4 x 4 Gb DDR3 at 533 MHz (DDR-1066) i.MX 6DualLite applications processor: 4 x 4 Gb DDR3 at 400 MHz (DDR-800) 32 MB 16-bit parallel NOR flash NAND flash socket LVDS output RGB parallel output Ethernet daughter card connector Atheros Gigabit Ethernet PHY (included in SABREAI kit)
SD card slot 2
www.nxp.com
High-Speed USB OTG interface
I2C module connector
SATA interface (i.MX 6Quad applications processor only)
De-serializer input for remote video/ camera input
JTAG and UART interfaces
Dual-channel video ADC to facilitate camera and video analog signal inputs
Capable of running stand-alone on common 5 V DC power supply 281 card-edge fingers for base board connection or interface to user’s system The following features are available with the SABRE platform for automotive infotainment base board:
USB host connector Sirius XM® radio module PCB lands Terrestrial broadcast tuner module connector GPS module connector (UART) MLB25/50 INIC connector
LVDS output
Low- and high-speed CAN interfaces
Multi-channel audio codec analog I/O for up to eight channel outputs, one stereo line input and two microphone inputs
Bluetooth® module connector (I2S + UART)
SPDIF receive interface
SD card interface (Wi-Fi® or data cards) 12 V DC input jack
3
Quick Start Guide GET TO KNOW SABRE PLATFORM FOR AUTOMOTIVE INFOTAINMENT BASED ON THE i.MX 6 SERIES SPDIF In, Video In
Mic In Audio Line In
Base Board Reset
Audio Line Out
Sirius XM Radio Module Lands
CPU Reset, Peripheral Reset
Android™ Buttons x5
Boot Config. Switches
MIPI 5 V DC Power In (for CPU Stand Alone)
12 V DC Power In
HDMI Out SATA
USB Host 5 V DC SATA Power Out
LVDS Out x2 NAND Flash Socket
USB OTG
Parallel Display Out
I 2C CAN x2 Module
JTAG
Ethernet
4
Debug UART
AVB/Legacy Mode Switches
ENET Daughter Card
SD Card Slot Boot Mode Switches
www.nxp.com
AM/FM Radio Connector
Expansion Port Connector (Not Used for i.MX 6 Series) Wi-Fi SD Card Slot
MLB 25/50 INIC Interface PHY Card Connector
BT Module Connector
5
Quick Start Guide GETTING STARTED This section describes how to use the SABRE platform for automotive infotainment and associated components.
1
Unpack the Kit
The SABRE platform for automotive infotainment is shipped with the items listed in table 1. Remove the circuit board from the conductive bag and perform a visual inspection to ensure all parts are included. ITEM
DESCRIPTION
Circuit Boards
SABRE platform for automotive infotainment CPU Card with ENET daughter card attached
USB hardware
Micro-A plug to standard-A receptacle cable
Cable
3-pin female to 3-pin male power cord (shipped with base board)
Power supply
12 V DC @ 5.5 A power supply (shipped with base board)
Documentation
Quick Start Guide (this document)
SD card
The kit will include an SD card with software if available at the time of shipment. Software can be downloaded from www.nxp.com/SABREAI
JTAG
10-conductor ribbon cable with 20-pin adapter card Table 1: SABRE Development Kit Contents
6
www.nxp.com
2
Download Software and Tools
Download installation software and documentation under “Jump Start Your Design” at www.nxp.com/SABREAI. Table 2 lists the documents available on the kit website.
“JUMP START YOUR DESIGN” CONTENTS ITEM
DESCRIPTION
SABRE platform for automotive infotainment documentation
Quick Start Guide (this document)
Software development tools
The latest BSPs and other software
SABRE platform for automotive infotainment design files
Design files, including hardware schematics, gerbers and OrCAD files
Table 2: “Jump Start Your Design” Contents
7
Quick Start Guide STEP-BY-STEP INSTALLATION INSTRUCTIONS
1
Insert SD Card
Insert the supplied SD card into the SD card socket J14 on the CPU card. Note: The SD card will be included if ready at date your kit was shipped. If there is no SD card, please visit the www.nxp.com/ SABREAI to download software.
2
Set Up Boot Switches
Verify that the switches are set to boot from SD card per tables 3 and 4. Ensure jumpers are correct per table 6.
8
3
Connect RS-232 Cable
Connect a user-supplied RS-232 cable to CPU card debug port J18. Support the connector with one hand while plugging in the cable to minimize flexing the board. Serial port configuration: 115.2 kbaud, 8 data bits, 1 stop bit, no parity, no flow control
4
Connect HDMI Monitor
After boot-up, the SD card outputs the OS desktop through the HDMI port.
www.nxp.com STEP-BY-STEP INSTALLATION INSTRUCTIONS
5
Connect an LVDS LCD (optional)
Connect a display to CPU card connector J13. Part number MCIMX-LVDS1 is a compatible display with touch panel.
6
Attach JTAG (optional)
7
CONTINUED
Connect USB OTG (optional)
Connect the cable from the kit to micro USB connector J10 on the CPU card. Note: To avoid damage, the micro USB plug must be carefully inserted upside down.
Connect the ribbon cable to both the JTAG adapter card and CPU card connector J17. (The connectors have key slots to ensure proper orientation.) Then, plug in the user-supplied cable to the JTAG interface while supporting the adapter.
9
Quick Start Guide STEP-BY-STEP INSTALLATION INSTRUCTIONS
8
Connect Power Supply
Setup A—CPU Card Mated with Base Board First, plug in the 12 V DC supply to base board power jack J1, followed by plugging in the 120/240 V AC cord to a wall outlet. Four green LEDs and one yellow LED on the CPU card plus two red LEDS on the base board should illuminate when the system powers up properly. An additional supply is not needed for the CPU card. Do not plug in a supply to CPU card J8. Important: To ensure proper boot up and to minimize stress to the system, do not hot-plug a live 12 V DC supply to J1. Tip: Use a power strip with a switch for convenient power on/off control. To re-boot, press CPU card reset button SW1.
10
CONTINUED
Setup B—CPU Card Stand-Alone First, plug in a user-supplied 5 V DC supply to the CPU card power jack J8, followed by plugging in the 120/240 V AC cord to a wall outlet. A 5 A supply is recommended. Four green LEDs and one yellow LED should illuminate when the system powers up properly. Important: To ensure proper boot up and to minimize stress to the system, do not hot plug a live 5 V DC supply to J8. Tip: Use a power strip with a switch for convenient power on/off control. To re-boot, press CPU card reset button SW1.
www.nxp.com DIP SWITCH CONFIGURATION BOOT CONFIG SWITCH S2-1 S2-2 S2-3 S2-4 S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 S1-8 S1-9 S1-10
NAND FLASH 64 GB * 0 X 1 0 0 0 1 0 X X 0 0 0
NAND FLASH 16 GB * 0 X 1 0 0 0 1 0 X X 0 0 0
PARALLEL NOR FLASH 0 0 0 0 X X X X X 1 0 X X 0
SD ON CPU CARD * 0 1 0 * 1 X 0 1 * * * * *
MMC ON CPU CARD * 1 1 0 * * * 0 1 * * X X *
SATA HDD 0 1 0 0 * * * * * X X X X X
SERIAL NOR FLASH 1 1 0 0 X X X X X X X X X X
Table 3: Boot Configuration DIP Switches
Notes: 1=High Level 0=Low Level X=Don’t Care *=Switch needs to be configured for high or low depending on the application needs. Please check reference manual for boot configuration options. Default=0. Default boot configuration=SD on CPU card
To boot from SPI NOR, remove R193 on green base board. Orange base board requires no change. SD speed selection on S1-10 and S1-9: 00=SDR25, 01=SDR12, 10=SDR50, 11=SDR104 11
Quick Start Guide DIP SWITCH CONFIGURATIONS BOOT MODE
CONTINUED
FUSES
SERIAL DOWNLOADER
INTERNAL (DEVELOPMENT)
RESERVED
S3-2
0
1
0
1
S3-3
0
0
1
1
Table 4: Boot Mode DIP Switches
Notes: S3-1 TAMPER 0=Tamper detected 1=No tamper S3-4 SPI NOR WP_B 0=Write protect enable 1=No write protect
MODE CONTROL SWITCH
AVB (LISTENER)*
AVB (TALKER)*
MLB (LEGACY)
SW3-1
On
On
Off
SW3-2
On
Off
Pff
Table 5: AVB/MLB DIP Switches
* In AVB modes, AM-FM radio and RGB display should not be used, and USB OTG cable must be unconnected.
12
www.nxp.com
REFERENCE
SHUNT INSTALLATION
FUNCTION
J3
1–2 2–3
Do not boot from SPI NOR (default) Boot from SPI NOR
J4
1–2 2–3
Data out of SXM (default) Data out of GPS
J5
1–2 2–3
CAN control of system power Power control to ON fixed by this setting
Table 6: Jumpers
13
Quick Start Guide ENET DAUGHTER CARD OPTIONS In addition to the Atheros daughter card, two Broadcom daughter cards are available. There is one ENET board-to-board connector on the SABREAI CPU Card. Therefore, the Atheros ENET daughter card supplied with the CPU card must be removed to install the optional ENET cards. The figures show screw insertion points on the CPU card. The two 100 Mb/s cards are shipped with FlexRay™ cables. FUNCTION Circuit Boards
DAUGHTER CARD PART NUMBER
PRIMARY ON-BOARD IC*
IMXAI2ETH-ATH**
Atheros AR8031
100 Mb/s interface to BroadR-Reach automotive Ethernet
IMXAI2ETH-BRC
Broadcom BCM89810
100 Mb/s interface to standard LAN plus 4-port BroadR-Reach automotive Ethernet switch
IMXAI2SWCH-BRC
Broadcom BCM89501
Table 7
* Our company cannot recommend one supplier over another and we do not suggest that these are the only Ethernet PHY and switch suppliers. ** Supplied with SABREAI kit. This card also can be ordered separately.
14
www.nxp.com
IMXAI2ETH-BRC
IMXAI2SWCH-BRC
15
SUPPORT Visit www.nxp.com/support for a list of phone numbers within your region.
WARRANTY Visit www.nxp.com/warranty for complete warranty information.
Get Started Download installation software and documentation under “Jump Start Your Design” at www.nxp.com/SABREAI.
www.nxp.com/iMXSABRE All other product or service names are the property of their respective owners. ARM and Cortex are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved. © 2012–2015 Freescale Semiconductor, Inc. Document Number: IMX6SABREINFOQSG REV 5 Agile Number: 926-27925 REV E
