Quickstart “basic” Guidelines For Solar

Transcript

QUICKSTART “BASIC” GUIDELINES FOR SOLAR CONTROL BOX FOR 6003, 6004, 6005 OR 6400 Solar Power r Cu w Dra y Ke ad P ver cei -081 e R 55 P/N DoorKing RF Radio Receiver Mount inside of control box door. 80 12 3 #1 #2 #3 Com GND SW1 GND 1476-010 Full Open-Power Terminal Radio #1 Com (White) Radio #2 Relay (Green) Radio #3 Power (Red) N.O. Com 250 ma Maximum Power Battery Plug Power Com DETECT DSP-7 Diablo Controls, Inc. Stuck in traffic for over 37 years! POWER RELAY NC COM NO COM + LOOP Reverse Loops POWER 10 to 30 Volts AC or DC POWER RELAY NC COM NO COM + se ver p Re Loo Reverse loops wired in series 6 7 8 Normally Closed Monitored OPEN Photo Sensor 9 10 11 12 13 14 15 16 17 18 19 20 Battery Switch Jumper wires for shadow loop. Black Wire Harness Disconnects battery power from circuit board. Solar panels still charge batteries. Copyright 2017 DoorKing, Inc. All rights reserved. tte itive VER RIC ry lea and touc ds neg h tog at eth ive er! DANGER of ELECTRIC SHOCK!! OPEN Beam Close Beam Switch 1 Must be ON for reversing edge. Closed Gate lt Vo 12 tery t Ba CLOSE Beam IMPORTANT: Photo OPEN Beam CLOSE Beam sensors must use Normally Closed (NC) contacts with the beam Monitored CLOSE set for light operate Photo Sensor (relay activated when beam is not obstructed). Switch 2 Must be ON. lt Vo 12 tery t Ba Battery Wiring Notes: Use ONLY 12 Volt batteries. Batteries are wired in series. ON 12 Volt 35 Amp/Hr batteries: Use for applications with higher usage (60 cycles per day or more). DA N SH GER o the OCK f EL E ! ba pos ! NE CT P (+) ositiv Re e d 1 2 DoorKing Recommends: 12 Volt 18 Amp/Hr batteries: Use for applications with normal usage (60 cycles per day or less). Dry Relay Contact Two 12 Volt Batteries N (-) egati Bla ve ck Monitored OPEN/CLOSE Reversing Edge ON N.O. NEG Terminal Lead Close Beam Switch 1 Must be ON. 1 2 Push to Operate: Cycles operator when pressed. Will use Auto-Close timer when turned ON. OPEN Beam ON 5 Normally Closed 1 2 2 3 4 DIP-switches MUST be turned ON for each device wired to terminal. Normally Closed OFF Dry Relay Contact operator before the limit sensors and DIP-switches have been adjusted, damage could occur to gate and operator. Circuit Board Terminal Full OPen DO NOT connect 12 Volt solar panel. Damage WILL occur!! DO NOT power up and cycle the gate ON NC POS Terminal Lead Loop Detectors Com Standard Reverse input on Terminal 8 ONLY functions while the gate is at the full open position or during the closing cycle. 1 See the specific loop detector instruction sheet for more information (P/N 9402-050). Solar Pos. (White Wire) Solar Neg. (Black Wire) Solar panel should face true south in unobstructed sunlight. • (1) One 24 Volt 20 Watt Solar Panel for 35 Amp/Hr Batteries (P/N 2000-076). technician use only NO See reverse side. PUSH TO OPERATE UL 325 Terminal 1476-010 Open Beam Close Beam Note: Only 1 monitored Device can be connected to each input. An OPTIONAL Expansion Kit (sold separately) will allow connection for additional devices. Common Low Current Draw External Loop Detectors se ver p Re Loo GND B Circuit board relay is used for reverse loops and must be set to N.O. Primary Operator ONLY DO NOT Connect a Plug-In Transformer to the Solar Power Terminals UL 325 DIP-Switches SW11 GND 12 V Battery Input op Keep sunlight OFF solar panel while connecting to prevent electric shock. • (1) One 24 Volt 10 Watt Solar Panel for 18 Amp/Hr Batteries (P/N 2000-077). 24 V NEG LOOP t Lo Exi 24 Volt Solar Panel Solar Control Box Requirements: Relay COM Solar NEG DSP-7 Diablo Controls, Inc. OPEN/CLOSE Edge/Beam (Switch 1) CLOSE Beam (Switch 2) Not Used SW 1 Solar POS DETECT CB Not Used SW 1, switch 5 is OFF. Stuck in traffic for over 37 years! REMOVE CONNECTOR TO RESET REMOVE CONNECTOR TO RESET N.O. Com POWER 10 to 30 Volts AC or DC LED Flashing: Connected device is in fault. Wiring to device is bad. 1 2 OB See reverse side. 24 V POS LED ON: Connected device has been activated. LED remains off during normal operation. Only 1 Device can be wired to each input. Connect to circuit board. Not Used N.O. SW 2 All potential entrapment areas MUST be protected with an external entrapment protection device. At least ONE external entrapment protection device MUST be installed or the operator will NOT function. - Shuts alarm OFF - Resets circuit board Secondary Operator ONLY Not Used Use 18 AWG minimum. Exit Loop (Dry contact) LOOP RESET BUTTON A Open Beam Close Beam Relay N.O. Safety Opening Device POWER RELAY NC COM NO COM + ON Primary Secondary Low Voltage UL 325 Terminal CB t ren Standard Reverse ON 1 2 3 4 1. OFF - Circuit Board Relay Control 2. ON - Circuit Board Relay Control 3. OFF - Maglock 4. OFF - Spare Stuck in traffic for over 37 years! LOOP 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 A DSP-7 OB Low SW1, Switch 1&2 Note: See reverse side for your specific operator switch settings. 1. Direction Primary operator opens. 2. Direction Secondary operator opens. 3. Open Input 4. Auto-Close Timer B 5. Standard Reverse 6. Overlapping Gates 7. Single/Dual Operators Adjust11 to23 23 sec. 8. ON POWER RELAY NC COM NO COM + Shadow Loop Note: A shadow loop can NOT be wired to the solar control box. DETECT Diablo Controls, Inc. DO NOT USE “Optional” Loop detector DO NOT USE mounting positions Reverse Loop Port Exit Loop Port Coax Antenna Kit P/N 1514-073 Typical Settings with Reverse and Exit Loops. See reverse side. SW 1 POWER 10 to 30 Volts AC or DC DSP-7 Stuck in traffic for over 37 years! N.O. y Ke itch Sw DETECT Diablo Controls, Inc. 1 2 Circuit Board Settings 10 to 30 Volts AC or DC 1 2 Typical conduit configuration (not supplied). DoorKing offers an OPTIONAL mounting post kit (P/N 1000-045) when no vertical surface is available to mount the control box cabinet to. POWER Use existing screws to mount detector(s) ON le xib Flenduit Co Antenna mounted outside control box. Opening Devices (Dry contact) OPEN Beam it du on uts C ” o 3/4 nock K le Ho na n e t An uit nd ts Co ckou ” 3/4 Kno o Ph y Open Gate Ho Loops ng nti u Mo ntr E ne UL 325 Terminal External Entrapment Protection Devices Loop Detector P/N 9402-050 Full Open et n i b Ca ack B le U.S.A. Pedestrians must be supplied with a separate access opening. For safety and complete installation and adjustment instructions, please refer to the Wiring/Owner’s manual. Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating the controls. Do not connect any control devices to the circuit board terminal. DANGER of ELECTRIC SHOCK!! tin un Mo 120 S. Glasgow Avenue Inglewood, California 90301 Control box is intended for installation only on automated gates used for vehicles. Power Com les o gH Opening Devices REMOVE CONNECTOR TO RESET Position the control box on the wall, close enough to the gate operator so the primary operator cable can be easily routed inside the box. Use appropriate hardware (not supplied) in the existing 3 mounting holes to secure the cabinet to a vertical surface. DO NOT drill any additional holes in the cabinet. Drilling produces metal filings, which can cause shorts on the circuit board and will void the warranty. • Never run high voltage and low voltage wire insulation in the same conduit. REMOVE CONNECTOR TO RESET Mount Control Box Cabinet THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. Visit www.dkslocator.com to find a professional installing and servicing dealer in your area. 4302-068-Q-6-17 QUICKSTART “BASIC” GUIDELINES FOR SOLAR CONTROL BOX DIP-SWITCH REFERENCE AND OPERATOR(S) CONNECTION Switch Function Setting SW 1 DIP-Switches SW 2 DIP-Switches Description Whenever any programming or switch setting on the control board is changed, press the reset button for new settings to take effect. Opening Direction of PRIMARY Operator Switch Function Setting 1-OFF 2-ON 3 4 Maglock Spare OFF OFF SW 2 Description OB CB Circuit board relay activates when the gate is NOT closed. NO maglock is used. Leave in the OFF position. SW1 GND GND 1476-010 Opens Inside 6004 ONLY Left-Side Right-Side ON 1 2 3 4 5 6 7 8 Opens Inside 7-Wire Operator Actuator Cable Opens Outside 6005 ONLY 6400 ONLY Open Same Drive Motor Orientation Opens Outside Open Closed Opens Inside Open 3 Not Used 4 Auto-Close Timer Reverse Not Used Overlapping Gates 5 6 7 8 Single Dual Input Power Open Same Drive Motor Orientation Same opening directions as illustrated above for the secondary operator. • Switch 2 will be the SAME setting as switch 1 for the 6003. • Switch 2 will be the OPPOSITE setting as switch 1 for the 6004, 6005 and 6400. Note: SW1, switch 7 MUST also be ON when using a secondary operator. OFF Leave in the OFF position. OFF ON OFF (normal) ON OFF ON OFF ON ON Auto-close timer is OFF. Manual input required to close gate. Auto-close timer is ON. Adjustable from 1-23 seconds. Terminal #8 is a standard Reverse input. On setting is NOT used. Both operators start at the same time. Secondary operator opens 1-2 seconds before primary operator. Vice-versa when closing. Switch must be OFF for single operator. Switch must be ON when (dual) operators are used. Switch MUST be in the ON position. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Note: RED and GREEN wires from operator cable are not used. Factory Factorywired wiredjumpers jumpersMUST MUST remain remainconnected connectedas asshown. shown. SLO DWN LEDs are always lit. 1 2 3 4 5 6 7 8 Brown wire Blue wire Orange wire Red wire Yellow wire Green wire Green/Yellow wire NOT USED Brown wire Blue wire Yellow wire JUMPER Orange wire JUMPER Green/Yellow wire JUMPER 6400 Wiring Brown wire Blue wire Orange wire Red wire Yellow wire Note: Secondary operator MOTOR wires Green wire MUST be reversed from the primary Green/Yellow wire operator when using DUAL gate operators. NOT USED OR S TO 25 RAT 247 FORM TO /UL-3 NO. CONANSI E OPE HP IFIED 2 GAT CERT C22. AR CSA E CAN/ ICUL PHAS S VEH Hz 60 CLAS EL , CA MOD AL wood SERI S Ingle LOAD VOLT S Inc., GATE AMP King, MAX Door Factory wired jumpers MUST be removed. Secondary operator wiring SECONDARY 1 2 3 4 5 6 7 8 PRIMARY 6005 Primary/Single operator wiring 6005 Wiring Closed 2 D O O R K I N G Brown wire Blue wire Orange wire Red wire Yellow wire Green wire Green/Yellow wire NOT USED Factory wired jumpers MUST be removed. Opens Inside Opening Direction of SECONDARY Operator Refer to your specific operator for limit sensor adjustments. FULL OPEN Primary/Single operator wiring 6003 Wiring 6004 Wiring BEFORE setting limit sensors. Close Beam Primary/Single Operator Cable ONLY 1 2 3 4 5 6 7 DO NOT cycle the operator 2 SW 1 Choose Your Operator Model: Follow wiring colors for the PRIMARY/Single or DUAL gate operators. 5338 1 Opens Outside Brown wire Blue wire Orange wire Red wire Yellow wire Green wire Green/Yellow wire Open Beam Secondary Operator Cable ONLY 1 2 3 4 5 6 7 Gate Operator(s) Connection 1 2 1 and 2 Relay Operation U.S.A. ON 6003 ONLY ON Opens Outside 1 2 3 4 The operator MUST OPEN GATE upon initial power up and OPEN command. If the operator closes gate after giving open command, shut off power and reverse this switch setting otherwise operator will NOT function correctly. 120 S. Glasgow Avenue Inglewood, California 90301 1 2 3 4 5 6 7 8 6005 Secondary operator wiring SECONDARY Brown wire Blue wire Yellow wire JUMPER Orange wire JUMPER Green/Yellow wire JUMPER 1 2 3 4 5 6 7 8 PRIMARY 6400 Primary/Single operator wiring Blue wire Brown wire 1 2 3 4 5 6 7 8 Orange wire Red wire Yellow wire Green wire Green/Yellow wire NOT USED PRIMARY 6400 Secondary operator wiring SECONDARY 1 2 3 4 5 6 7 8