Radio Controlled Home Automation

Transcript

Radio controlled home automation for retro-fit and new projects Hager quicklink is a home automation system accessible to all installers. It's an easy to use radio operation, offering control of applications for lighting, shutters and blinds. R.4 radio transmitters R.5 radio receivers R.6 technical guide R.7 Radio control automation radio transmitters & receivers quicklink Hager democratises home automation Hager quicklink home automation is an offer based on a new configuration mode: quicklink mode! Requiring neither training nor a specific configuration tool, this new radio offer is available to all installers for retro-fit, renovation or new projects. 3 1 4 2 Your benefits: Technical data: • KNX home automation without training. • KNX radio 868,3 MHz. • Extremely simple configuration. • Direct quicklink • Accessible home automation for all installers. • Range: 100 m outdoors and across two concrete sections. • Radio operation — no trunking or chasing of walls. • Also configurable with TX100 and ETS. • Enjoy the decorative richness of kallysta. • Control applications for lighting, shutters and blinds. configuration on the products. Expert tips 1 2 Home automation for you Radio commands A new configuration mode without tools, without training: quicklink . For installations without trunking or chasing. The new colours of home automation 1 function = 1 colour. 3 A choice of 35 kallysta frames To satisfy all decorative requirements of your customers. Preconfigurated kits 100% KNX products For a simpler and faster implementation. tebis products can also be configured with TX100 and ETS. A distinctive button All quicklink products are equipped with a configuration button "cfg". 4 Products tailored for renovation Installation in 40mm depth boxes. quicklink KNX radio transmitters and receivers quicklink is a configuration mode that does not require a Hager programming tool. This mode is based on learning by pressing the buttons located on the products. These products enable control of lighting, shutters, blinds or receivers operating together or individually. Characteristics - Preconfigured kits - Bidirectional products - Frequency: 868.3 MHz KNX radio - Configurable with TX100 and ETS - Range: 100m in open field and across two concrete sections. Connection capacity - 0,75 to 2 x 2,5 mm² Lighting functions - ON/OFF (impulse) - ON - OFF Description - ON/OFF (switch) - ON/OFF (dimming) - ON (dimming « + ») - ON (dimming « - ») - timer - scenario - repetition (presence simulation) Shutter functions - Up - Down - Scenario - Up/down (switch) - Force up - Force down - Repetition (presence simulation) The repetition function It saves the commands carried out over a period of time. Once learned, the user may repeat the sequence automatically in a period of 24 hours. Examples: - Shutter up/down at fixed times - Simulation of presence (lighting). One of four pushbuttons is dedicated to this function. For technical information, see page R.8. Characteristics Pack qty. Cat. ref. kallysta ON/OFF without neutral (2 wire) - 1 output 25… 300W/VA (not CFL or LED) - 2 pushbutton inputs 1 WKT400 kallysta ON/OFF with neutral (3 wire) - 1 output 16A AC1, all loads - 2 pushbutton inputs 1 WKT401 kallysta ON/OFF dimming without neutral (2 wire) - 1 dimming output 25 … 300W/VA (not CFL or LED) - 2 pushbutton inputs 1 WKT410 kallysta dimming without neutral (2 wire) with repetiton - 1 dimming output 25 … 300W/VA 1 (not CFL or LED) - 4 pushbutton inputs WKT412 kallysta input/output mechanisms for lighting WKT401 kallysta input/output mechanisms for dimming WKT412 kallysta input/output mechanisms for shutters and blinds 1 WKT421 kallysta up/down 3 wire ( , , Ph, N) with repetiton function - 1 output 5A for 1 motor - 4 pushbutton inputs 1 WKT422 kallysta up/down 4 wire ( , , Ph, N) with repetiton function - 1 output 5A for 1 motor - 4 pushbutton inputs 1 WKT423 Description Characteristics Pack qty. Cat. ref. KNX radio remote controls 2 buttons 1 TU402 Delivered with battery (CR2430–3V) 4 buttons 1 TU404 6 buttons 1 TU406 6 buttons 18 channels 1 TU418 ➞ ➞ ➞ ➞ WKT421 ➞ - 1 output 5A for 1 motor - 2 pushbutton inputs ➞ kallysta up/down 4 wire ( , , Ph, N) WKT422 TU404 TU418 R.4 quicklink KNX radio transmitters The radio buttons allow the addition of extra operating points without the need for cabling. Characteristics - Transmitters are uni–directional in use and bi–directional during configuration - Frequency: 868.3 MHz radio KNX - Low battery indication - Average life of battery: 5 years - Range: 100m in open field Radio wall detectors Can be fixed in a location and used to control a radio receiver with a 230V 10A contact. Description Characteristics Pack qty. Cat. ref. Mechanisms for KNX radio pushbuttons Supplied with: - 1 protective site cover - 1 double sided sticker - 1 battery CR2430–3V 2 way/2 buttons 1 WKT302R 4 way/4 buttons 1 WKT304R 6 way/6 buttons 1 WKT306R Description Colour Pack qty. Cat. ref. 2 buttons Cat. ref. 4 buttons Cat. ref. 6 buttons kallysta covers Supplied with a label dimensions: 57 x 57 mm white carbon sand silver 1 1 1 1 WKT902B WKT902C WKT902D WKT902T WKT904B WKT904C WKT904D WKT904T WKT906B WKT906C WKT906D WKT906T Description Colour Pack qty. Cat. ref. shutters and blinds Cat. ref. dimmers kallysta 2 buttons silkscreened covers - for dimmers - for shutters and blinds white carbon sand silver 1 1 1 1 WKT942B WKT942C WKT942D WKT942T WKT952B WKT952C WKT952D WKT952T Description Characteristics Pack qty. Colour Cat. ref. Decorative frame dimensions 80 x 80mm 1 white WK401 1 carbon WK501 1 sand WK411 1 silver WK491 1 white TRE520 1 anthracite TRE521 1 white TRE530 1 anthracite TRE531 1 white TRE600 Characteristics - Available in batter and solar versions - Detection angle: 220° - IP55/IK04 - Uni–directional in use and bi– directional during configuration - Frequency: 868.3 MHz KNX radio - Range: 100m in free field - Delivered with 3 x 1.5V batteries. For technical information, see pages R.9, R.10, R.16 and R.17. WKT904B WKT904C WK411 Suitable for all kallysta switches IR movement detectors wall mounted KNX radio TRE520 battery emitter solar emitter IR movement detector and LED floodlight TRE600 Pushbuttons IP55 KNX radio Recessed input modules KNX radio TRE302 TRB302B 1 button/1 input 1 TRE301 2 buttons/2 inputs 1 TRE302 2 input battery supply 1 CR1/2 AA 3V for 2 volt–free input contacts TRB302A 2 input 320V supply 1 for 2 volt–free input contacts TRB302B R.5 Radio control automation WKT306R quicklink KNX radio receivers KNX radio receivers act as power interfaces to control electrical loads. Characteristics - Bi–directional receivers - Frequency: 868.3 MHz KNX radio - Lighting functions - ON/OFF (impulse) - ON - OFF Shutter functions - Up - Down - Scenario Description Characteristics Pack qty. Cat. ref. 1 output ON/OFF 16A/230V AC1 1 TRB201 1 volt–free input 1 output contact 10A 230V 1 TRB501 1 output shutter/blind up/down 4 wire ( , , Ph, N) 5A/230V AC1 1 TRB221 2 volt–free inputs 2 output contacts 1 TRB521 Recessed dimmer KNX radio max load 200 W halogen/incandescent lamps 1 TRB210 Receivers ON/OFF IP55 KNX radio dimensions 150 x 85 x 35mm 1 output 10A/230V AC1 1 TRE201 2 outputs 10A/230V AC1 1 TRE202 1 output shutter/blind up/down 4 wire ( , , Ph, N) 10A/230V AC1` 1 TRE221 Receiver 1 input + 1 output IP55 KNX radio 1 volt–free input contact 1 output 10A/230V AC1 1 TRE400 Motion detector kit IP55 KNX radio includes: 1 TRE520 motion detector 1 TRE201 wall mounted output 1 TRE720 KNX radio switch activator for plugs for remote-controlled switching of electrical loads 1 TRC270D ON/OFF (switch) Timer Force ON Force OFF - Up/down (switch) - Force up - Force down For technical information, see page R.8. Combined input/output unit KNX radio TRB201 Recessed shutter/blind receivers KNX radio ➞ Combined input/output unit KNX radio ➞ Recessed receivers ON/OFF KNX radio TRB221 Receiver shutter/blind IP55 KNX radio dimensions 150 x 85 x 35mm ➞ TRE202 R.6 ➞ TRB210 Flush-mounted radio output modules, quicklink Radio plug adapter actuator, quicklink : TRC270D Flush-mounted radio dimmer, quicklink Ph N 1➀ 2➁ ➀ fct cfg : TRB210 ➁ on off ➂ ➃ ➀ Configuration button and LED cfg ➁ Function button and LED fct for the output Radio control automation ➀ Configuration button and LED cfg ➁ Radio transmitter ➂ Function button and LED fct for the output ➃ Terminal strip – L : Phase 230 V – N : Neutral – : Dimmer output R.7 Putting quicklink products into service It is possible to configure virtually any function in push-button mode – i.e. using the buttons on the devices themselves. Each transmitter is equipped with a configuration button (cfg) and each receiver is equipped with a configuration button and a function button (cfg + fct) for this purpose. All of the functions are indicated by coloured LEDs, whereby the fct button can be used to simply “scroll through” them. cfg cfg fct on off fct fct on off fct cfg >2s 1. Activating configuration mode Briefly press the cfg button on the transmitter. The cfg LEDs on the transmitter and all receivers light up. 2. Configuring the transmitter Briefly press the channel button to which a function is to be assigned on the transmitter. The cfg LED on the transmitter flashes for 1 second. Transmitter and receiver are now in configuration mode. 3. Selecting a function Press the fct button on the receiver repeatedly until the chosen function in indicated by the fct LED. 4. Confirming the selected function Press the fct button on the receiver and keep it pressed for > 2 s until the cfg LED starts flashing to confirm the selected function. To configure a group control system, repeat steps 3 and 4 on all other receivers in the group. cfg 5. Terminating configuration Briefly press the cfg button on the transmitter again. The cfg LEDs on the transmitter and all receivers go out. The configuration process really is “quick”! LED fct Switching outputs Dimmer Shutter/blind outputs Function Function Function ON/OFF (one surface control element) ON/OFF, dimming ± ON ON, dimming + Opening, stop OFF OFF, dimming - Closing, stop Scene 1 Scene 1 Scene 1 Scene 2 Scene 2 Scene 2 Time switch Time switch ON/OFF (switch) ON/OFF (switch) Roller shutter ctrl. system (switch) Forced mode ON Forced mode OPEN Forced mode OFF Forced mode CLOSE Delete Delete R.8 Delete Flush-mounted radio input modules, quicklink Input modules: TRB302A/B TRB302A TRB302B Power supply Battery 1/2 AA (3 V) 230V AC, 50 Hz ± 15% Inputs 2 for floating contacts Contact current 30 µA 30 µA Input current 19 mA 19 mA Battery service life 5 years - Transmit frequency 868.3 MHz 868.3 MHz Range Indoors Outdoors Max. 30 m Max. 100 m Max. 30 m Max. 100 m Operating temperature 0 °C to +45 °C 0 °C to +45 °C Storage temperature –20 °C to +70 °C –20 °C to +70 °C Ingress protection rating IP30 IP20 Dimensions H × W × D 48 mm × 51 mm × 16 mm 48 mm × 53 mm × 27 mm Connection Plug-in connector, connecting wires 200 mm long Flush-mounted radio input module, 2-gang, battery-powered, quicklink , TRB302A Flush-mounted radio input module, 2-gang, 230 V, quicklink , TRB302B 1 + - 3 Radio control automation 2 cfg cfg cfg 4 3 TRB302B LED cfg ➀ Battery compartment cover ➁ Battery, type 3 V CR ½ AA ➂ Configuration button and LED cfg ➃ Plug-in connector with connecting wires for the inputs (20 cm long) Made in France 6T1131b 2 Receiver category 2 Transmitter duty cycle 1 % 230 V cfg L N 1 Ph N ➀ Terminal strip for the power supply ➁ Configuration button and LED cfg ➂ Plug-in connector with connecting wires for the inputs (20 cm long) R.9 Flush-mounted radio input modules, quicklink Surface-mounted radio tactile sensor, IP55, quicklink TRE302 Contact assignments for external inputs : TRE301/ Technical data Power supply 2×CR 2430 3.0 V (TBTS, SELV, ZLVS) Estimated service life of the battery 5 years 0 Transmit frequency 868.3 MHz Range in open spaces 100 m Dimensions 76 mm × 49 mm × 23 mm Cable length <3m Minimum dwell period 50 ms Ingress protection rating – with wires connected IP55 IP31 Operating temperature –10 °C … +50 °C Storage temperature –20 °C … +70 °C Standards EN 60950-1 / EN 301489-3 EN 300220-2 / EN 50491-3 1 2 Installation 2 2 1 0 1 7 6 cfg LED 3 ➀ The configuration button and LED cfg are located under the cover ➁ Transmission pilot light ➂ Operator control buttons ➃ Screw plugs for the battery compartment ➄ Wall-mounting holes ➅ Terminal strip holder ➆ Terminal strip for external inputs 5 4 Activation of one of the buttons States indicated by the transmission pilot light ➁ State of the LED Colour of the LED Meaning Lights up briefly Green Transmitting the control command, input configured Flashes for 2 seconds Green Transmitting the control command, scene input (teach-in mode) Flashes for 1 second Orange Input not configured Flashes for 1 second Red Low battery charge Does not light up - – No batteries or very low charge – Batteries fitted the wrong way round The device may be mounted to the wall with double-sided adhesive tape or screws. The following must be taken into consideration when using external inputs: – Mounting orientation, i.e. horizontal or vertical alignment – Supply line < 3 m R.10 Flush-mounted radio output modules, quicklink Flush-mounted radio switching output modules quicklink dimmer output module quicklink TRB210 TRB201 Power supply TRB201, TRB501, socket quicklink TRB501 TRC270D and TRC270D TRB210 230V AC, 50 Hz ± 15% Inputs 1, for floating contacts Outputs µ 16 A 230V AC, AC1 µ 10 A 230V AC, AC1 µ 16 A 230V AC1 for resistive loads / µ 10 A 230 V AC1 for lamp loads Type Switching capacity for: - Incandescent lamps - 230 V halogen lamps - LV halogen lamps with CTR - LV halogen lamps with ETR - Fluorescent lamps Max. 120 µF NO contacts NO contacts NO contacts Dimmer 2300 W 2300 W 1600 VA 1500 W 1500 W 800 VA 2300 W 2300 W 1600 VA 20 … 300 W 20 … 300 W 20 … 200 VA 1200 VA 800 VA 1200 VA 20 … 200 VA 20 × 36 W Max. 47 µF 11 × 36 W Max. 120 µF 20 × 36 W Connection Flexible Rigid 1.5–2.5 mm² 1.5–2.5 mm² 0.5 … 2.5 mm² 0.5 … 2.5 mm² Transmit frequency 868.3 MHz Range Indoors Outdoors Max. 30 m Max. 100 m Operating temperature 0 °C to +45 °C 0 °C to +45 °C 0 °C to +45 °C 0 °C to +45 °C Storage temperature –20 °C to +70 °C –20 °C to +70 °C –20 °C to +70 °C –20 °C to +60 °C Ingress protection rating IP30 IP30 IP30 IP30 Dimensions H × W × D 48 × 53 × 30 mm 48 × 53 × 30 mm 98 × 40 (80) × 54 mm 48 × 53 × 38 mm CTR: conventional transformer ETR: electronic transformer ECG: electronic control gear Flush-mounted radio module, 1 output, quicklink Ph N : TRB201 Flush-mounted radio module, 1 input/output, quicklink Ph N ➀ ➀ ➁ ➁ TRB201 ➂ ➂ ➃ ➃ ➀ Configuration button and LED cfg ➁ Radio transmitter ➂ Function button and LED fct for the output ➃ Terminal strip – L: Phase 230 V – N: Neutral – ▼: 230 V contact output ➀ Configuration button and LED cfg ➁ Function button or conventional button ➂ Function button and LED fct for the output ➃ Terminal strip – L: Phase 230 V – N: Neutral – ▼: 230 V contact output R.11 : TRB501 Radio control automation 1.5 … 2.5 mm² 1.5 … 2.5 mm² Flush-mounted radio output modules, quicklink Flush-mounted radio blind module, 1 output, quicklink 2 inputs/1 output, quicklink : TRB521 Power supply : TRB221 / flush-mounted radio blind module, TRB221 TRB521 230V AC, 50Hz ± 15% 230V AC, 50Hz ± 15% Inputs 2, for floating contacts Outputs 2, µ 6 A 230V AC, AC1 2, µ 6 A 230 V AC, AC1 Power dissipation 2W 2W Delay time between 2 opposite directions 600 ms 600 ms Transmit frequency 868.3 MHz 868.3 MHz Range Indoors Outdoors Max. 30 m Max. 100 m Operating temperature 0 °C to +45 °C 0 °C to +45 °C Storage temperature –20 °C to +70 °C –20 °C to +70 °C Ingress protection rating IP30 IP30 Dimensions H × W × D 48 mm × 53 mm × 30 mm 48 mm × 53 mm × 30 mm Connection Flexible Rigid 1.5 … 2.5 mm² 1.5 … 2.5 mm² 0.75 … 2.5 mm² 0.75 … 2.5 mm² Flush-mounted radio blind module, 1 output, quicklink TRB221 : Flush mounted radio blind module, 2 inputs/1 output, quicklink TRB521 Ph N Ph N 1 2 2 TRB221 LED LED cfg N L 3 2 fct fct 4 1 3 TRB521 10 A M LED LED cfg cfg cfg fct N L ➀ Configuration button and LED cfg ➁ Radio transmitter ➂ Function button and LED fct for the output ➃ Terminal strip – L: Phase 230 V – N: Neutral – ▼: Open – ▲: Close fct 4 10 A M ➀ Configuration button and LED cfg ➁ Button ➂ Function button and LED fct for the output ➃ Terminal strip – L: Phase 230V – N: Neutral – ▼: Open – ▲: Close R.12 : Flush-mounted radio output modules, quicklink Technical data Maximum load per switching output TRE20x / TRE400 230V AC Incandescent lamps 1500 W Power supply 230V DC +10–15% 230V AC Halogen lamps 1500 W Transmit frequency 868.3 MHz Conventional transformer 600 W Switching capacity per output 2 (µ 16 A 230V AC, AC1) 12V DC 24V DC Ingress protection rating IP55 12V DC 24V DC Electronic transformer 600 W Operating temperature –10 °C … +55 °C 230V AC 600 W Storage temperature –20 °C … +70 °C Electronic transformer ballast Dimensions (H × W × D) 150 mm × 85 mm × 35 mm Fluorescent lamps with ECG 6 x 58 W Connection 0.75 mm² to 2.5 mm² Fluorescent lamps with conventional ballast connected in parallel - Energy-saving lamps 6 x 18 W Connection Surface-mounted radio output modules, 1 output, IP55, quicklink : TRE201 1 fct S1 TRE201 1x 10 A fct LED 2 LN 3 cfg S1 1 2 34 5 6 78 LED cfg Radio control automation 1 2 34 5 6 78 4 Ph N ➀ Configuration button and LED cfg ➁ ➂ Function buttons and LEDs fct for outputs S1 and S2 ➃ Terminal strip Surface-mounted radio output modules, 2 output, IP55, quicklink : TRE202 fct S1 S2 fct TRE202 2 x 10 A Surface-mounted radio module, 1 input + 1 output, IP55, quicklink ; connection: TRE400 fct S1 TRE400 cfg cfg S1 S2 LN LN 1 2 34 5 6 78 1 2 34 5 6 78 Ph N E1 S2 Ph N R.13 Surface-mounted radio output modules, quicklink Surface-mounted radio blind output module, 1 output, IP55, quicklink : TRE221 TRE221 Power supply 230V DC +10–15% Transmit frequency 868.3 MHz Delay time between 2 opposite directions 600 ms Ingress protection rating IP55 Operating temperature –10 °C … +55 °C Storage temperature –20 °C … +70 °C Dimensions (H × W × D) 150 mm × 85 mm × 35 mm Standards EN 60669-2-1 EN 301489-3 EN 300220-2 EN50491-3 EN50428 Connecting TRE221 TRE221 fct cfg LN 1 3 4 5 26 7 8 Ph N R.14 Surface-mounted radio motion detector, IP55, quicklink Surface-mounted radio motion detector, battery and solar-powered, IP55, quicklink TRE52x/TRE53x Technical properties TRE52x (battery) TRE53x (solar) TRE600 Colour white, anthracite white, anthracite, alum., brown white Detection zone 220° + 360° 16 m to the front / 10 m to the side 360° detection: 6 m diameter under the sensor 120° + 360° 12 m to the front / 10 m to the side 360° detection: 6 m diameter under the sensor Head adjustment (vertical) +90°/–30° - Head adjustment (horizontal) ±80 LED lamp adjustment - Masking panels Supplied with the devices Corner bracket (inside/outside) EE855 white; EE856 anthracite 180° (horizontal) / 340° (vertical) - Potentiometer brightness adjustment 5 to 1000 lux Time delay adjustment 30 s to 15 min Sensitivity adjustment 20 to 100% Transmit frequency 868.3 MHz Controlled by remote control TU4xx Pilot light detection Yes Power supply 3 × 1.5V AAA Range 100 m (open spaces) Solar cell with back-up battery LED power 230V AC approx. 60 W (300 W white-hot) EN EN EN EN 609 50-1 301489-3 300220-2 50491-3 Ingress protection rating IP55 IK code 04 Ambient conditions – Storage temperature – Operating temperature –20 °C to +55 °C –20 °C to +60 °C Dimensions (L × W × H) 153 mm × 91 mm × 130 mm Motion detector, quicklink : TRE52x/TRE53x Radio control automation Standards 322 mm × 150 mm × 257 mm Detection range: TRE52x/TRE53x Description IP55 16 m 10 m vertical adjustment 16 m α 220/360° + 90°/- 30° +/-80° 10 m setting potentiometer wall mounting plate 2,5 m 4m 0,5 m rotary sensor 8m Recommended installation height 2,5 m. The detection zone must be free of obstructions at all times. R.15 Surface-mounted radio motion detector, IP55, quicklink Motion detector, quicklink : TRE600 Detection range: TRE600 Description 8m rotary light panel 180 ° Wall mount with power supply unit ø 0,6 m 8m 8m 2,5 m 340° 12 m Recommended installation height 2,5 m. The detection zone must be free of obstructions at all times. setting potentiometer rotary sensor masking panel Installation: TRE52x/TRE53x Corner adapter: TRE52x/TRE53x Masking panels: TRE52x/TRE53x ➀ Installation: TRE600 Ph N Clac ! Ph N R.16 ➁ Surface-mounted radio motion detector, IP55, quicklink Device adjustments Time delay (OFF delay) TRE5xx cfg button Brightness Sensitivity (changing the range) Fitting the batteries: TRE52x button LED C cfg cfg 30 s lux 5 min 15 min - auto test + TRE600 cfg button LED A LED B fct cfg Device adjustments Setting Light switched on automatically for a predetermined period of time according to standard settings (factory). This function is only available if the time delay has been programmed for the detector. Automatic settings Set lux potentiometer to “auto-test”. The default settings are as follows: Lux = , (night mode only) period = 3 min Sensitivity = max. Light switched on automatically for a predetermined period of time. This function is only available if the time delay has been programmed for the detector. Electrician settings Testing and confirming the detection range. Test mode Set potentiometer 2 to “auto-test”. Adjusting the sensitivity. Function on /off ON/OFF (staircase lighting circuit) on ON OFF 1 Scene 1 2 Scene 2 Time switch ON/OFF (switch) on Forced mode ON off Forced mode OFF auto test Presence simulation Delete R.17 lux 5 min 15 min Used to set the sensitivity in order to avoid perturbation. off lux 30 s Used to set the range in order to prevent interference Adjusting the sensitivity. LED fct Potentiometer - auto test lux lux auto test auto test - + - + + Radio control automation Operation