Rcs® Remote Control Systems

Transcript

Throttle pedal systems The development of this throttle operation is unique, because the throttle cable is fully integrated into the pedal. That means: • The throttle cable is operated from inside the pedal. • No additional spatial requirement underneath the vehicle or the cabin floor. • No large breakthroughs necessary, only a simple hole pattern for 3 screws and the sealing plugs. Features Pedal: • Pedal angle continuously adjustable 42-1 • Slip-proof pedal rubber on the tread surface Travel 60 mm 40° • Robust steel sheet metal design, corrosion protected by black surface treatment Cable: ~ 25 ° • Smooth operating throttle cable with high efficiency, particularly suitable also for large lengths ~ 200 Idle travel • Optimal assembly thanks to small bend radius of min. 51 mm • Pulling loads of max. 450 N ~ 115 Full speed • Can be employed at temperatures from 50° C to + 90° C (short term + 150° C) • Throttle cable travel can be adjusted continuously between 20 mm – 60 mm General information: ~ 60 155 ~ 105 42-2 • A variety of end part variations for connection to the engine • System-oriented accessories range • Available for higher temperature upon request Restoring force N 32 34 Art.-No.: 4569-000023 36 30 28 Restoring force 24 0 mm travel Full speed 42-3 42 Accessories for hand throttle Throttle pedals for pull only cable 283-U-GAS/… and 283-V-GAS/… 60 Anti-slip surface Counter-nut M5 SW7 Clamp sheet positions throttle cable for travel adjustment 60 mm ma Tra vel x. 27 0 Bolt for travel adjustment Throttle cable Fastening bolt for cable holder M8 Thread rod for adjusting the pedal angle Cable holder Return spring SW 10 6 40 M8 15 68 53 32 ø 25 ø 6,6 (5x) 45 70 155 43-1 Assembly plate For easy screwing through the vehicle floor. 6 Art.-No.: 3570-000014 30 ø 25 15 32 53 M6 (3x) 70 45 155 43-2 43 Design of the cable ends for throttle pedal systems Pull only cable 283-U-GAS and 283-V-GAS Pedal connection GAS: Travel 60 5 Motor connection T05M: Hub Seal No. 05 7 7/16-20 UNF A/F 17 M5 10-32 UNF L[cm]±5mm 60 20 14 14 Travel ø 9,4 Seal No. 05 Motor connection G05M: M5 10-32 UNF ø 6,35 In idle: 185* / 210* end parts 2"/3 60 20 3,4 8 7 Travel M5 10-32 UNF In idle: 185* / 210* end parts 2"/3" 60 7/16-20 UNF A/F 17 Motor connection T00M: 20 13 14 14 Motor connection COMP: min. 70 max. 150 78* A = ±5 7/16-20 UNF A/F 17 15 ** Travel 60 M6 7 30 8 40 min. 70 max. 150 152 7/16-20 UNF A/F 17 15 ** 7 Seal No. 05 Travel 30 129 In idle: 186* / 211* end parts 2"/3 * Other lengths, threads and motor connections available upon request • ** Compensated excess travel and exceeding the max. pull force 44 M5 10-32 UNF Motor connection COMPT: 60 A = ±5 60 20 Accessories for hand throttle Hand throttle cable and attachment kit Hand throttle cable + attachment kit directly at the throttle pedal Micro-adjust control cable: 275-U-MA/04-3-xxxx (cm) directly alternativly Attachment kit: 3570-000001 Cable directly at the injection pump Throttle cable 283-V-GAS/T05M-2.36-xxxx (cm) 45