Transcript
DC2R Remote Training System With LCD display and of 300 meters range ◎Controller
Features : 1.100 levels of vibration. 2.100 levels of shock(optional). 3.The levels can be altered by use of up & down button. 4.A tone button activates a tone on the receiver collar. 5.The system can be used for 1 or 2 receivers’ collars. 6.Four modes --shock, vibration, light and beep mode, meet your different training needs. 7.300 meters usage range in open areas. 8.Power saving design: the controller enters sleep mode after 20s of no operation, and wakes up by pressing MODE for 1s; the receiver enters sleep mode after 20s no movement, and wakes up when moving.
◎Getting charge 1. Charge the controller Connect the charger connector to the charging jack. After plugging the charger into a standard outlet，the red LED light inside the transmitter will be lighted. Charge the controller at least 6 hours for the first charge. After fully charged, the red LED light will be turned off automatically.
2. Charge the receiver collar After plugging the charger into a standard outlet, the red LED light inside the receiver collar will be lighted. Charge the receiver collar at least 6 hours for the first charge. After fully charged, the red LED light will be turned off automatically.
◎How to match 1. Please press the MODE button of controller for 5-10s, then the controller will be turned on. Press the CHANNEL button LED screen).
and select CHANNEL1 (the small icon
can be seen at the upper right of the
2. Press the reset button with a needle for 5s within 20 seconds (the Controller is in the ready state after it has been started)).While finishing installing the battery, you will hear a sound “beep”.
3. Then press the Y button of controller immediately and you can hear a “beep” again. That shows the item is paired successfully. If not, please remove the batteries of collar and install them once again, and try the above steps.
Matching the second collar If you have another collar, please follow the next steps to finish matching. 1. Please press the MODE button of controller for 5-10s, then the controller will be turned on. Press the CHANEL button screen).
and select CHANNEL 2 (the small icon
can be seen at the upper right of the LED
2. Press the reset button with a needle for 5s within 20 seconds. While finishing installing the battery, you will hear a sound “beep”. 3. Then press the Y button of controller immediately and you can hear a “beep” again. That shows the item is paired successfully. If not, please remove the batteries of receiver collar and install them once again, and try the above steps. Note: CHANNEL 1 and CHANNEL 2 are in no order, so you can set any collar to any CHANNEL according to you custom. ◎Intensity Regulation The shock and vibration function can be set from 0 to 100 by pressing the UP/DOWN buttons on right hand side. When using shock or vibration, you can choose intensity levels according to your needs.
◎Using The Four Models (after encoding is completed) Four modes can be altered by pressing the MODE button of controller.
1. Shock Model Test the static shock function （1) Take out the test bulb from the package and put it on the Receiver collar’s contact points.
(2) Press MODE button of controller, switch to Shock Mode (the small icon can be seen at the upper left of the LED screen). Press UP/DOWN button on the right side confirming LCD display is not to be 0.
(3) Press Y button and observe the change of test bulb. You can see flash light in the middle of test bulb that means the shock function works.
Use the shock function (1) When using the shock function, you need to install the receiver’s contact column. According to the size of the dog and dog hair length, choose the right column for your dog between the tall one and short one.
(2) Thread the collar strap through the slots on the receiver, and tie it to the dog.
2. Vibration Model (1) Press Mode button of controller, switch to Vibrate Mode (the small icon can be seen at the upper part of the LED screen). Press UP/DOWN button on the right side confirming LCD display is not to be 0.
(2) Press Y button, Receiver collar will vibrate, that means Vibration function works. 3. Beep Model (1) Press Mode button of Controller, switch to Beep Mode (the small icon part of the LED screen).
can be seen at the upper
(2) Press the Y button and receive collar will beep, that mean Beep Function works. 4. LED Light Model
(1) Press Mode button of Controller, switch to LED light Mode (the small icon upper right of the LED screen).
can be seen at the
(2) Press the Y button and then the receiver collar and the indicator light of controller will flash at the same time, signifying that the LED Light function works. ◎Package includes 1 x remote control 1 x collar 1 x charger cord 1 x test light&probes 1 x Maual ◎Notes for Function: 1. The lifetime of the batteries vary according as how often you use the product. Therefore you should often check batteries when the receiver collar makes sound “beep beep” and the right down side of LCD screen shows up the symbol
.
2.The valid distance of Controller means the straight-line distance between the Controller and the Receiver Collar without obstacles in between. If there are interference signals or signal screening around, the actual remote Controller distance may vary. 3.If you hear a little ratting sound inside the collar, don’t worry. It is the Touch switch used to wake up the collar when in sleep mode. ◎Training Tips 1. Before you use the training collar, read the instructions carefully and learn to use it. Make sure both function are OK and then attach the receiver collar to your dog’s neck.
2. Practice using the electronic remote training collar. Start at the lowest level of stimulation and observe your dog when you activate it. The dog's ear might twitch or he may move his head as if trying to get away from the collar. If your dog doesn't respond at the lowest stimulation, slowly turn the transmitter to the next level and try again.
3. Reinforce commands your dog understands. When you train your dog with an electronic collar, begin with commands the dog is familiar with. Say the command, such as sit or stay, and wait for your dog to respond. If your dog is not paying attention, press the button on your transmitter and repeat the command. Praise your dog as soon as he responds. Reward your dog with a pat, by saying "good dog," or with a special treat. When you train dogs, you want to reinforce their good behavior with a reward.
5. Control bad behavior. Plan for bad behavior. For instance, if your dog digs holes in the backyard whenever you let him outside, be ready to use an electronic collar to train him when you let him out. Don't let your dog see you. You don't want your dog to know you are causing the unpleasant sensation around his neck when he starts digging. Rather, you want him to associate the sensation with the bad behavior. Set the stimulation on the transmitter to a low level, and if that is not effective, turn it up again. You want to get the dog's attention without hurting him. When the dog begins to dig, or engage in whatever behavior you want to control, activate the transmitter. Do not hold the button down for more than 3 seconds and do not punch it repeatedly. The object is to train your dog, not injure him.
◎Notes of training 1. Don't leave an electronic remote training collar on your dog for more than 12 hours at a time because it may irritate the dog's neck. 2.This product is for pet training. Only by training, the pet can understand the Good effect can only be achieved after a period of training.
intention of its owner.
3.Training sessions should be kept positive and short, about 10-15 minutes long each time.
