Transcript
4
Testing the Modules (Host/Remote)
1. Set the DIP Switch for Host on one unit, Remote on the other. Enable SNMP DIP Switches depending on what port has been chosen for SNMP. 2. Establish link on the copper and optics ports. 3. Open the CLI, and type the command config; choose the Transparent Mode.Assign a VLAN ID to management, type reboot and close. 4. Pass traffic or PING from side to side. 5. Units can be set back to default factory settings by typing in the command cleandb in the CLI. SNMP Questions Which port have you assigned to use for management (SNMP)
Recommended Accessories iView² Network Management Software http://www.bb-elec.com/ iview iMediaChassis Managed 3, 6 & 20 Slot Platforms http://www.bb-elec.com/ Products/Ethernet-MediaConverters/IMC-NetworksModular-Chassis-Series/ iMediaChassis-Managed-3,-620-Slot-Platforms.aspx
Do you have SNMP services from the WIN CD installed? iView² The iMcV-FiberLinX-II is supported by the iView² Webserver version and desktop version. Check Type of Cable Used A CAT 5 or higher Ethernet cable is required for the RJ-45 ports. Make sure that the pins are not pulled out of the connector’s casing, which will cause damage to the device’s copper ports. PING Test To perform a PING test, between two pairs across the fiber segment, Port 3 must be set to “enable” for SNMP.
Fast, Easy Answers Use your smart phone to access complete documentation on our web site. Simply scan the code to the right.
iMcV-FiberLinX-II Managed Optical Demarcation Module
First Things First...
Before you begin, be sure you have the following:
Resources For optimal performance of the device, make sure to download the latest version of software and firmware for the device. these are avilable on the B&B website.
iMcV-FiberLinX-II Required but not included: Fiber cabling dependent on fiber type
For information about warranty and product specifications, please refer to the datasheet or the website.
CAT 5 Ethernet cable RJ-45 to dB9 adapter
1-888-948-2248 | Europe: +353 91 792444
MediaChassis, iMediaChassis series
www.bb-elec.com 707 Dayton Road | PO Box 1040 | Ottawa, IL 61350 Phone: 815-433-5100 | Fax: 815-433-5109 www.bb-elec.com | E-mail:
[email protected] Document number – 55-85011-00_R1_iMcV-FiberLinX-II_4114qsg
© 2014 B&B Electronics Manufacturing Company
Fast and easy on the web: www.bb-elec.com
Product Overview
Select the DIP Switch Settings
2
Diagnostic LEDs LED
Default Settings
Status Host
FCU (Far CPU Up)
LEDs
Ethernet
Fiber Port SFP Port LEDs
1
Configure the Software
1. Use the serial port for the initial configuration. The serial port is on the unused pins of the EXT MGMT Ethernet port. You will need an RJ-45 to dB9 adapter. 2. Default IP address: 10.10.10.10 3. Set your computer for VT-100 or ANSI emulation. 4. Set the serial port on your computer to the following: • 38.4K baud • 8 data bits • 1 stop bit • No parity • No flow control 5. After the initial self-test is complete, the prompt “Press
for Device Configuration” appears. 6. After the Main Configuration screen opens, press I to change the Saved IP Configuration Parameter Values. 7. At the prompt, type the IP address, and then press . 8. Type the subnet mask for the device, and then press . When you install the iView² program the auto scan feature will detect the modules, and configuration through the Graphical User Interface (GUI) will become possible.
Switch
Function
1 2
Management on EXT MGMT port Management on Data port Management on Optics or Uplink port
3 4
Factory Use—Do not change
5 6 7 8 9 10
Factory Use—Do not change Factory Use—Do not change Remote unit Host unit Factory Use—Do not change Factory Use—Do not change
Default ON OFF
SNMP
ON Green
EXT 100
ON Green
DATA 100
On Yellow
OFF
OFF OFF
1. On the remote unit, move DIP Switch 7 to the ON position. 2. On the host unit, move DIP Switch 8 to the ON position.
3
LED
FDX/COL
LNK/ACT
ON Yellow Blink Yellow ON Green Blink Green
Function Port is operating in Full-Duplex Collisions occurring on the port Link is established on the port Data activity on the port
Green indicates this is an SNMP-manageable module Green when the EXT MGMT port is operating at 100 Mbps Yellow when DATA port is operating at 100 Mbps
Function
ON Green
Green when FiberAlert is enabled Fiber Alert is not enabled. FA not available for Single Strand Fiber versions ON - Green when a link is established on remote (far end) DATA port ON - Green when unit is configured as Remote
OFF
Host FTL (Far TX Link)
Remote Standalone
Status
LED is OFF
Status
FA
Port LEDs LED
Green when far end is detected Green for remote units
Optics Port
Settings for management and Host/Remote are only configurable via DIP Switches.
Check the LEDs
Remote Standalone
Function
LNK/ACT (Link/Activity) FDX/COL (Full Duplex/ Collision)
ON Green Blink Green On Yellow Blink Yellow
LED is OFF Link is established on port. Data activity on port Port is operating in Full-Duplex Collisions occurring on the port
