Transcript
4
Testing the Modules (Host/Remote)
1. Set the DIP Switch for Host on one unit, Remote on the other. Enable SNMP DIP Switches depending on what port has been chosen for SNMP. 2. Establish link on the copper and optics ports. 3. Open the CLI, and type the command config; choose the Transparent Mode.Assign a VLAN ID to management, type reboot and close. 4. Pass traffic or PING from side to side. 1. The instructions are for a Host/Remote application. 2. The default configuration is standalone. For optimal product performance, refer to our website for the latest software and firmware versions.
Recommended Accessories iView² Network Management Software http://www.bb-elec.com/ iview iMediaChassis Managed 3, 6 & 20 Slot Platforms http://www.bb-elec.com/ Products/Ethernet-MediaConverters/IMC-NetworksModular-Chassis-Series/ iMediaChassis-Managed-3,-620-Slot-Platforms.aspx
Fast, Easy Answers Use your smart phone to access complete documentation on our web site. Simply scan the code to the right.
iMcV-Giga-FiberLinX-II Optical Ethernet Demarcation Device
First Things First...
Before you begin, be sure you have the following: iMcV-Giga-FiberLinX-II Required but not included: Fiber cabling dependent upon fiber type CAT 5 or higher Ethernet cable DB9 cable
1-888-948-2248 | Europe: +353 91 792444
MediaChassis, iMediaChassis series
www.bb-elec.com 707 Dayton Road | PO Box 1040 | Ottawa, IL 61350 Phone: 815-433-5100 | Fax: 815-433-5109 www.bb-elec.com | E-mail:
[email protected] Document number – 56-85868-00_R1_iMcV-Giga-FiberLinX-II_4114qsg
© 2014 B&B Electronics Manufacturing Company
Fast and easy on the web: www.bb-elec.com
Product Overview
2
Select the DIP Switch Settings Diagnostic LEDs
Default Settings
LED LEDs
Host
Console
FCU (Far CPU Up)
Data Port Ethernet SFP Port Fiber Port LEDs
SNMP
ON Green
Switch
Default
EXT 100
ON OFF
ON Green
DATA 100
On Yellow
Function Management on EXT MGMT port Management on Data port Management on Optics or Uplink port
3
Configure the Software
1. Use the serial port for the initial configuration. The serial port is on the unused pins of the EXT MGMT Ethernet port. 2. Default IP address: 10.10.10.10 3. Set your computer for VT-100 or ANSI emulation. 4. Set the serial port on your computer to the following: • 38.4K baud • 8 data bits • 1 stop bit • No parity • No flow control 5. After the initial self-test is complete, the prompt “Press
for Device Configuration” appears. 6. After the Main Configuration screen opens, press I to change the Saved IP Configuration Parameter Values. 7. At the prompt, type the IP address, and then press . 8. Type the subnet mask for the device, and then press . When you install the iView² program the auto scan feature will detect the modules, and configuration through the Graphical User Interface (GUI) will become possible.
Remote Standalone
1. On the remote unit, move DIP Switch 7 to the ON position. 2. On the host unit, move DIP Switch 8 to the ON position.
1 2
1
Status
4
Factory Use—Do not change
5 6 7 8 9 10
Factory Use—Do not change Factory Use—Do not change Remote unit Host unit Factory Use—Do not change Factory Use—Do not change
3
OFF OFF
Port LEDs
FDX/COL
LNK/ACT
ON Yellow Blink Yellow ON Green Blink Green
LED is OFF Green indicates this is an SNMP-manageable module Green when the EXT MGMT port is operating at 100 Mbps Yellow when DATA port is operating at 100 Mbps
Optics Port LED
FA
Collisions occurring on the port Link is established on the port Data activity on the port
Function
ON Green
Green when FiberAlert is enabled Single-strand fiber versions ON - Green when a link is established on remote (far end) DATA port ON - Green when unit is configured as Remote
Host Remote Standalone
Function Port is operating in Full-Duplex
Status
OFF
FTL (Far TX Link) Status
Green when far end is detected Green for remote units
OFF
Check the LEDs
LED
Function
LNK/ACT (Link/Activity) FDX/COL (Full Duplex/ Collision)
ON Green Blink Green On Yellow Blink Yellow
LED is OFF Link is established on port. Data activity on port Port is operating in Full-Duplex Collisions occurring on the port
