Transcript
1N4933G
RECTRON
THRU
SEMICONDUCTOR TECHNICAL SPECIFICATION
FAST RECOVERY GLASS PASSIVATED RECTIFIER
1N4937G
VOLTAGE RANGE 50 to 600 Volts CURRENT 1.0 Ampere
FEATURES * * * * *
High reliability Low leakage Low forward voltage drop Glass passivated junction High switch capability
DO-41
MECHANICAL DATA * * * * *
Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.35 gram
1.0 (25.4) MIN.
.205 (5.2) .166 (4.2)
.034 (0.9) DIA. .028 (0.7)
.107 (2.7) .080 (2.0)
DIA.
1.0 (25.4) MIN.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o
Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters)
MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL
1N4933G
1N4934G
1N4935G
1N4936G
1N4937G
Maximum Recurrent Peak Reverse Voltage
RATINGS
VRRM
50
100
200
400
600
Volts
Maximum RMS Voltage
VRMS
35
70
140
280
420
Volts
VDC
50
100
200
400
600
Volts
Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 55 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range
UNITS
IO
1.0
Amps
I FSM
30
Amps
CJ
15
pF
T J , T STG
-55 to + 150
0
C
ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25 oC Maximum Full Load Reverse Current Full Cycle Average, .375” (9.5mm) lead length at T L = 55 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 1.0A, VR = 30V 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts
SYMBOL VF
1N4933G
1N4934G
1N4935G 1.2
1N4936G
1N4937G
UNITS Volts
5.0
uAmps
100
uAmps
200
nSec
IR
trr
2002-11
1.50 1.25 1.00 .75 .50
Single Phase Half Wave 60Hz Resistive or Inductive Load
.25 0 25
50 75 100 125 150 175 AMBIENT TEMPERATURE, ( )
FIG. 3 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, (pF)
200 100 60 40 20 10 TJ = 25
6 4 2 1
.1
.2
.4
1.0 2 4 10 20 40 REVERSE VOLTAGE, ( V )
100
PEAK FORWARD SURGE CURRENT, (A)
FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE
INSTANTANEOUS FORWARD CURRENT, (A)
AVERAGE FORWARD CURRENT, (A)
RATING AND CHARACTERISTIC CURVES ( 1N4933G THRU 1N4937G ) FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 40 30 20 10 8.3ms Single Half Sine-Wave (JEDED Method)
0 1
2 4 6 810 20 40 6080100 NUMBER OF CYCLES AT 60Hz
FIG. 4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS 20 10
1.0
TJ = 25 Pulse Width = 300us 1% Duty Cycle
.1
.01 .6
.8
1.0
1.2
FIG. 5 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1
8 115Va 10K 60Hz 2W 7
2 3.8uH/1.4 3
C.P.CLARE HPG 1002
30 50W NON-INDUCTIVE
UNIT UNDER TEST
6 5
4
30 Vdc CONSTANT VOLTAGE SUPPLY
1 AMP SLO-BLO FUSE C1 1.0uF 300V
R2 C1 1 1.0uF 10W 300V NONINDUCTIVE
MINIMIZE ALL LEAD LENGTHS A-TEKTRONIX 545A. K PLUG IN PRE AMP P6000 PROBE OR EQUIVALENT R2-TEN-1W 10 IN PARALLEL R1-ADJUSTED FOR 1.4 BETWEEN POINT 2 OF RELAY AND RECTIFIER 10 TA = 25 INDUCTIVE = 3.8uH 0
1.4
INSTANTANEOUS FORWARD VOLTAGE, (V)
1.0 Adc FROM CONSTANT VOLTAGE SUPPLY RIPPLE = 3mVrms MAX
trr i(t) IFM 1.0
di/dt = 50A/uS
0
Zout 11/2 MAX DC to 2kHz % CARBON CORE
FOR RECTIFIER
IRM (REC) SET TIME BASE FOR 50/100 ns/cm
RECTRON
Mouser Electronics Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Rectron: 1N4936G-T 1N4937G-B 1N4937G-T 1N4935G-T 1N4933G 1N4934G 1N4935G 1N4936G 1N4937G 1N4936GB 1N4935G-B 1N4933G-B 1N4933G-T 1N4934G-B 1N4934G-T
