Transcript
Remote Trainer Owners Manual
Spray Control
Components
IV. Turning on your remote tr
! Transmitter ! Receiver with collar ! Spray control refill canister ! Batteries ! Training manual ! Owners manual ! Video
Mode
automa conserv
I. Assemble collar Measure your pet’s neck, mark the appropriate length, and cut off the excess collar. Seal the edge of the cut by taking a match or lighter along the frayed edge.
one beep
connect
Important Note: Slide buckle also prevents collar from becoming loose around your dog’s neck.
Step 1: Thread slide buckle onto the collar first.
Step 2: Thread end of the collar up through the buckle. Important Note: Ribs must be facing up, otherwise collar will slip if it is not properly threaded.
Step 3: Thread excess collar through the slide buckle to hold it in place. This will allow you to adjust your pet’s collar as he grows.
Two beeps
connect
Note: When cutting off excess collar, be sure to leave enough slack for your dog's growth.
II. Fill receiver ! Place the receiver on a flat surface with the filling valve facing upright. ! Hold refill canister upside down. ! Insert nozzle into refill valve. ! Apply firm pressure for approximately 10 seconds.
III. Install batteries observe proper polarity remove screws (2)
9 volt battery
2
-
+ 6 volt battery
connect
slide battery door open
Long Beep
3
Slowly then sep
IV. Turning on your remote trainer & selecting the operating mode Mode 1. Automatic Shut-off - Receiver shuts-off automatically after 45 minutes of non-use to conserve battery power.
gth, and cut off the excess collar. Seal ng the frayed edge.
one beep
connect
Important Note: Slide buckle also prevents collar from becoming loose around your dog’s neck.
Slowly place two dots together for 3 seconds and then separate. Listen for one short beep.
Mode 2. Manual Shut-off - Receiver remains on until manually turned off. After placing the receiver in mode 1, within 5 seconds of the first beep, slowly place dots together again for three seconds and then separate. Listen for two short beeps.
Important Note: Ribs must be facing up, otherwise collar will slip if it is not properly threaded.
Two beeps
connect
ugh slack for your dog's growth.
To turn receiver off from either Mode 1 or 2.
g valve facing upright.
Slowly place dots together for 3 seconds and then separate. Listen for a long beep. observe proper polarity
-
+ 6 volt battery
connect
slide battery door open
Long Beep
3
V. Operating the transmitter Program Correction Length Level 1 = Light correction (approx. 0.10 seconds). Level 2 = Medium correction (approx. 0.15 seconds). Level 3 = Strong correction (approx. 0.25 seconds). To Program Correction level, hold down the P button. After 2 seconds, the receiver will beep 1-3 times, indicating the present level. Continue to hold the P button down until the number of beeps equals the level of correction you want. After Level 3, the receiver will go back to Level 1.
Signal indicator light Correction with negative tone. Negative tone only Program button
VI. Placing the Collar on your pet
] DO monitor your dog during initial use \ DON’T put collar on too tight. \ DON’T leave on for extended periods of time. \ DON'T use until reading the training manual and reviewing the video. VII. Begin Training Please read the training manual thoroughly and review the video before beginning training.
VIII. Maintenance Perform each of the following: ] Check batteries (weekly). ] Check your pet’s neck for any irritation (daily).
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device must not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation FCC ID: KE3SCT200.
Radio Systems Corporation, 10427 Electric Ave., Knoxville, TN 37932
4
1-800-732-2677 www.radiosys.com
400-227/C
