Transcript
Retrofit Kit 4
BlueRidge
Technologies Project
Part Number
Ref.
Data Sheet : Catalog Page 30 Overview Retrofit Kit (RK) replaces existing relay panel electronics. RK installation retains the original relays, line voltage wire, conduit, and enclosure reducing labor as well as material cost. Retrofit Kit 4 (RK4) is designed to convert existing relay panels which utilize 4-Wire relays. The kit includes a Controller, two 30-Relay Interface Boards (RIB), as well as two ribbon and two power cables. Each board is mounted on a single aluminum plate for installation. Features Compatible with : • MicroLite Panels (MLR-020) • Johnson Controls ILC Panels (JCI-ILC) • Touch-Plate Panels (3000-PL and 4000-PL) Retains relays, line voltage wire, conduit, and enclosure Control up to 60 relays BACnet MS/TP and N2 communication to BAS network Sub network for Capacitive Touch Stations (CTS-DDN) Install in less than 4 hours Available options: • LEXP Digital Input Expansion Card • PT4 4-Wire Relay Interface Pigtail General Specifications Construction: PCB’s mounted to 14ga aluminum plates Dimensions: Controller: 11.00”(279mm)H x 4.50”(113mm)W x1.56”(40mm)D RIB: 9.00”(229mm)H x 3.75”(94mm)W x 1.25”(32mm)D 14pin Ribbon Cable: 18”(457mm)L 20pin Ribbon Cable: 32”(812mm)L Power Cable: 18”(457mm)L Weight: 2lbs(1kg) Mounting: Panel back plate with self-tapping screws (not included) Operating Environment: 32-125°F (0-50°C), 20-95%RH, non-condensing Certifications Electronics meet or exceed IEC Level 3 CEC Title 24 Warranty Two (2) year limited manufacturer warranty from date of shipment (extended warranty optional). Controller Specifications Power In: 24VAC +/-10%, 30VA, 50-60 Hz Auxiliary Out: 24VAC Full Wave Rectified Digital Input: 24 two-wire inputs Software Configuration: Maintained, state change, momentary on/off, momentary on, or momentary off Jumper Configuration: 8 input segments, dry contact (N) or 24VDC externally powered (R) Wire Requirement / Maximum Length: 18AWG (Solid or Stranded) / Dry Contact 500’(152m) or externally powered 1,000’(304m) Analog Input: 6 three-wire 0-5VDC inputs Wire Requirement / Maximum Length: 18AWG (Solid or Stranded) / 250’(76m) BAS Network Specifications BACnet MS/TP Baud Rate: DIP switch selectable 9.6K, 19.2K, 38.4K, or 76.8K Device Profile: BACnet Advance Application Controller (AAC) Address Range: 1 – 99 selectable with rotary dials Unit Load: Full unit load, 32 devices per MS/TP segment N2 Baud Rate: DIP switch selectable 9.6K Address Range: 1 – 255 selectable with rotary dials and DIP switch
BACnet MS/TP and N2 Topology: RS-485, 3 conductor (+, -, and shield), daisy chain wiring (no stars or t-taps) Wire Requirement / Maximum Length: Belden 8760 / 4000’(1216m) Points: See Application Guide and PIC Statement DDN Network Specifications Compatible with CTS-DDN and DDN devices. See data sheet for details. RIB Specifications RIB-A: 30 relay outputs, drives relays 1-30 RIB-B: 30 relay outputs, drives relays 31-60 Relay Output Rating: 24VDC Relay Output Compatibility: 1 3000-PL or equal per, no external power / switches Relay Output Connection: 3 pin header, keyed for PT4 4-Wire Relay Interface Pigtail connection Wire Requirement / Maximum Length: 18AWG / 50’(15m) Optional Equipment Specifications LEXP Specifications Description: Digital Input Expansion Card Digital Input: 32 two-wire inputs Software Configuration: Maintained, state change, momentary on/off, momentary on, or momentary off Jumper Configuration: 8 input segments, dry contact (N) or 24VDC externally powered (R) Wire Requirement / Maximum Length: 18AWG (Solid or Stranded) / Dry Contact 500’(152m) or externally powered 1,000’(304m) Dimensions: 6.00”(152mm)H x 4.50”(113mm)W x1.13”(29mm)D PT4 4-Wire Relay Interface Pigtail: Description:18”(457mm)L,18AWG, 3-wire Pin/Color Code: 1/Yellow, 2/Red, 3/Brown RIB Connection: Keyed 3pin plug-on connector Relay Connection: 4 Insulation Displacement Connectors (IDC), 2216AWG, UL Listed
BAS
BAS Router
20A 1θTerminations Controller Field Devices
Satellite/Station Network
20A 1θ RIB-A Terminations
20A 1θ Field Devices
Rotary Switch 10’s Baud Rate / Protocol Network DDNAddress Network Dip Switch Network Address Relay Panel (RP) Rotary Switch 1’s
Relays 1-16 DDN Network
Zone Control (ZC)
ON
5
6
7
78
78 4
456
3
8
456
2
23
1 2 3
1
BT485 S B- A+
SW1 SW3
SW4 OVER
AUTO
DDN Network
Retrofit Interior (RI) DDN Network
901
901
23
BAS (+) In BAS (-) In Satellite/Station Network Shield
20A 1θ Field Devices
Field Devices
1
Relay Output 1
RIB-B Terminations
20A 1θ Telephone Line POTS
Relays 17-32
Retrofit Kit (RK)
Retrofit Kit 4
Relay OutputField 2 Devices
2
Relay Output 17
BACnet Telephone Override Module (BTOM)
1
2
Relay Output 18
BT485 3 4 3 4 Terminator Plug Satellite (if applicable) 20A 1θ www.BRTint.com : 800-241-9173 Blue Ridge Technologies® © 2012 Blue Ridge CTS-DDN International, LLC All Rights LVS Reserved. BRT-RK4-DS-V11.01 5 Technologies 6 5 OCC 6 Control CTS Override Controls (SC) Field Devices
20pin Ribbon Cable
J26 LEXP
RIB-A / RIB-B Relays 33-60 20A 1θ LEXP Port DDN Network
N
ZoneG Control 17 18 19 20 21(ZC) 22 23 24 17-24* 1-8 9-16 DI Jumper R R Satellite/Station Network N N 1-8*
24VAC(+) Power In 24VAC(-) Power In
G 1 2
Satellite 10 11 12 13 14 15 16 G Control (SC)
3 4 5 6 7 8 9
Field Devices
20A 1θ Switch 1’s Rotary Field Devices
7
78
78 6
456
5
8
SW4 DDN Network OVER
SW1 SW3 AUTO
1 2 3 BT485 S B- A+
Relay Panel (RP)
Yellow Yellow* Black Red Blue
14pin Ribbon Cable
LS5
OCC
Original RR8*, RR9, 2R9, or HDR5P Relay / Wiring IDC (Insulation Displacement Connector) IP *The yellow wire (RIB connector Pin 2) is capped when using RR8 relays. BACnet MS/TP
RIB-B Terminations
2
3
4
Retrofit Interior (RI)5
6
CTS-DDN
7
8
9
10
11
12
13
14
15 CTS-DDN (Capacitive Touch Station for RI/RK/RP)
Internet
LEXP Port
R
Relays 31-60
RO 1
1 AC OUT
RCS
1 2 3 4 5 6 7 8
LVS
LVS (Low Voltage Switch) / OCC (Occupancy Sensor) / LS5 (Light Sensor)
IDC
(2)
P
BACnet Telephone Override Module (BTOM)
Field Devices
CTS-DDN
ON OFF S
20A 1θ Telephone Line POTS
Retrofit Kit (RK)
Terminations
J26 LEXP
16
17
18
19
20
21
22
23
20A 1θ RO 2 Field Devices DDN Network
RO 31
20A 1θ 1 Telephone Line POTS 3
P
Retrofit Kit (RK)
RO 32
2 4
BACnet Telephone Override Module 6 5 (BTOM)
Field Devices
LVS
OCC
7
8
9
10
11
12
13
14
LS5
15 16 LVS (Low Voltage Switch) / OCC (Occupancy Sensor) / LS5 (Light Sensor) 17
18
19
20
21
22
24
23
24
25
26
25
26
27
28
27
28
29
30
IP
BACnet MS/TP
G 17 18 19 20 21 22 23 24 9-16 R N
N
24VAC(+) Power In 20A 1θ 24VAC(-) Power In Field Devices Power Cable DDN Network
AUX VAC
Zone Control (ZC)
Satellite CTS Control AI (Analog (SC) Input) / DI (Digital Input) / GND (Ground)
*DI Jumper Position N(Dry Contact) / R(Externally Powered) CTS (Capacitive Touch Station)
General Architecture
P G
DDN Network
20A 1θ Field Devices
CN8
DDN Network Retrofit Interior (RI) (1)
DDN NetworkPT4
3 4 5 6 7 8 9 10 11 12 13 14 15 16 G
GND DI 1 DI 2 DI 3 DI 4 DI 5 DI 6 DI 7 DI 8
GND DI 17 DI 18 DI 19 DI 20 DI 21 DI 22 DI 23 DI 24
(1)
Relay Panel (RP)
DI 9 DI 10 DI 11 DI 12 DI 13 DI 14 DI 15 DI 16 GND
Satellite/Station Network
20A 1θ Field Devices
Terminations
Pin 1 Pin 2 Pin 3
20pin
Retrofit Kit (RK) Ribbon Cable
Field Devices Yellow Red Brown Yellow
CTS-DDN
CTS-DDN (Capacitive Touch Station for RI/RK/RP)
RIB Connector
(A)
IDC
LVS
20A 1θ 29 Telephone Line P G POTS AC IN
1-8 R
INPUT POWER 24VAC
AC IN
N
G 1 2
Field Devices
16
20A 1θ Field Devices
CPU
Power LED Run LED CTS
BAS 17-24 Router
Satellite/Station DI Jumper Network 9-16*
20A 1θ
15
(A)
DDN Network
CTS (Capacitive Touch Station)
DI Jumper 17-24* 20A 1θ DI Jumper Field Devices 1-8*
16
AUTO OVERRIDE
Satellite Control (SC)
RUN
General Architecture 5VDC AI 6 AI 5 AI 4 AI 3 AI 2 AI 1 BAS GND
15
DDN Network
Override Controls
PWR
5V A6 A5 A4 A3 A2 A1 G
14
Internet
Power LED
456
4
23
3
Zone Control (ZC)
DDN/CAN
13
20A 1θ Field DevicesAUX OUT
901
901
2
23
1
Satellite/Station Network
24VDC 20A 1θ DDN Network(-) DDN FieldNetwork(+) Devices GND
14
PT5
Override Controls
ON
Terminator Plug (if applicable)
12
13
DDN Network
Relays 1-30
Baud Rate / Protocol Network Address Rotary Switch 10’s Dip Switch Network Address
IP 10
BACnet MS/TP
RIB-A Terminations
BAS Router
Satellite/Station BT485 Network
11
RIB Connector
Controller Terminations
BAS20A (+) 1θ In (-) In FieldBAS Devices Shield
12
Pin 1 Pin 2 Pin 3 Pin 4 Pin 5
AI (Analog Input) / DI (Digital Input) / GND (Ground) *DI Jumper Position N(Dry Contact) / R(Externally Powered)
BAS
11
CTS-DDN (Capacitive Touch Station for RI/RK/RP)
DI 9 DI 10 DI 11 DI 12 DI 13 DI 14 DI 15 DI 16 GND
GND DI 1 DI 2 DI 3 DI 4 DI 5 DI 6 DI 7 DI 8
GND DI 17 DI 18 DI 19 DI 20 DI 21 DI 22 DI 23 DI 24
DDN NetworkPT5
CTS
CTS (Capacitive Touch Station)
General Architecture
9
Retrofit Interior (RI)
24VAC(+) Auxiliary Out 24VAC(-) Auxiliary Out
AUX VAC
Internet 10
DDN Network
Relay Panel (RP)
INPUT POWER 24VAC
DI Jumper 9-16*
20A 1θ
20A 1θ Field Devices
Field Devices RELAYS 33-60
9
Power LED
1 2 3 4 5 6 7 8
Satellite/Station DI Jumper Network
7 8 LVS (Low Voltage Switch) / OCC (Occupancy Sensor) / LS5 (Light Sensor) CN2
Power LED Run LED
RELAYS 1-32
5V 5VDC A6 A5 AI 6 BAS BASA4 Router A3 AI 5 A2 A1 AI 4 G AI 3 20A 1θ AI 2 AI 1 Field Devices 17-24 GND R
Data Sheet : Catalog Page 31
7 8 CTS-DDN (Capacitive Touch Station for RI/RK/RP) CN1
CTS (Capacitive Touch Station) PWR 24VDC RUN DDN Network(-) General Architecture DDN/CAN DDN Network(+) GND
LS5
30
BACnet TelephoneRO Override (2) (Relay Module Output) (BTOM)
OCC
LS5
LVS (Low Voltage Switch) / OCC (Occupancy Sensor) / LS5 (Light Sensor)
PT4
Original Touch-Plate or MicroLite Relay / Wiring IDC (Insulation Displacement Connector) IP
Internet
Controller Terminations
BACnet MS/TP
Baud Rate / Protocol Network Address Rotary Switch 10’s BAS Router Dip Switch Network Address
BAS
Ordering Information BAS (+) In
Rotary Switch 1’s
20A 1θ SW1 SW3 SW4 Devices A+ BT485 S BKit for 4-wire relays, 3000-PL orField equal, 60 RO, 24 DI, 6 AI AUTO OVER 3
4
5
6
7
8
901
78
78
901
2
456
1
456
ON
23
1 2 3
BT485
Description
23
BAS (-) In
Part Number 20A 1θ Shield Field Devices BRRK4
20A 1θ Field Devices
Satellite/Station Network Network Terminator Plug Kit for 4-wire relays, 3000-PL orDDN BRRK4-L equal, 60 RO, 56 DI, 6 AI, LEXP (Card,DDN Mounting Plate, and Ribbon Cable) Zone Control (ZC) Relay Panel (RP) Retrofit Interior (RI) (ifNetwork applicable) BRPT4 4-Wire Relays, 18 Inches, Includes Insulation Displacement Connectors Override Controls Satellite/Station Network DDN Network 24VDC DDN Network(-) 20A 1θ DDN Network(+) GND
Field Devices
PWR DDN/CAN
RUN
Satellite Control (SC) RELAYS 1-32
Power LED Run LED
CTS
20A 1θ Telephone Line POTS
20A 1θ Field Devices
CTS-DDN
DDN Network Retrofit Kit (RK)
BACnet Telephone Override Module (BTOM)
Field Devices RO (Relay Output) / DI (Digital Input) / AI (Analog Input)
LVS
OCC
LS5
