Transcript
RF Solid State Amplifiers: The Most Innovative, Most Reliable, Highest Power RF Solid State Amplifiers Ever Created.
10
All The Power You Need…With Legendary Performance & Reliability “A” Series: Up to 400 MHz / 25 to 50,000 watts CW depending upon frequency range “W” Series: Up to 1,000 MHz / 1 to 10,000 watts CW Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band. We try to torture our amplifiers just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 watts that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own as shown in Figures 1 & 2. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications. These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers. These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
Figure 1 Mismatch Load Standards for 0.5 – 4.5 GHz
Figure 2 – Mismatch Standards for DC – 700 MHz
11
AR Ultra High Power Amplifier Capabilities AR’s history of providing broadband, high power amplifiers has remained constant through the years. Applying the latest technology has enabled us to break new ground in very high power, solid state amplifier design.
Facility We made an investment two years ago to create a Large Amplifier Integration and Test Area. Not only did this open up floor space to support the building of multiple systems but it brought added HVAC capabilities for the amplifiers and primary AC power to properly conduct factory testing. Engineers now have the freedom to create designs to accommodate multiple configurations and optimize performance. The area also supports customer factory acceptance testing as required.
Air vs. Liquid Cooling Liquid cooling of the amplifier’s solid-state transistors has a number of advantages. First, it allows for precise temperature control of the devices. The number one factor determining the reliability of solid state devices is temperature. By carefully controlling the temperature, engineers can optimize the performance of the amplifier without sacrificing reliability. Second, it reduces the size of the amplifier. Air-cooled amplifiers use large metal heat sinks over which air is forced to carry away heat. In a liquid-cooled amplifier, the transistors are mounted on cooling plates through which water flows. The plates are much smaller than heat sinks and because you don’t have to accommodate air flow they can be built closer together. Third, it reduces the heat load on the amplifier room and its resulting HVAC requirements. Since most of the heat generated is carried away by the cooling, liquid room HVAC requirements are reduced. Fourth, it allows for fewer fans. This makes the amplifier audibly quieter. By reducing the noise, operators can work in a safer, more pleasant environment without fatigue. Fifth, it gives customers the option of using existing cooling infrastructure to save costs. Liquid cooling options include an external chiller or the use of chilled water supplied by the customer’s facility. By utilizing existing infrastructure, operating costs can be reduced. AR’s high power amplifiers incorporate our latest Touch Panel amplifier control system*. This new system makes it easier to monitor and control important amplifier functions. On the right are some example screen shots unique to one of AR’s newest ultra high power amplifiers. See page 69 for more details on the AR’s intuitive touch panel capabilities.
12
* Touch Panel amplifier control system
13 13
“A” and “W” Series Amplifiers Provide A Wide Range Of Features & Benefits • • • • • • • • • • •
14
Highest Output Power In Its Class - Enough Margin To Obtain The Necessary Field Strength You Require Unsurpassed Service, Support & Warranty - Reduce Down Time To Save Money And Provide Your Customers With Testing Continuity Durability & Longevity - Provides Lower Life Cycle Costs Best Efficiency In Its Class - Reduces Operating Costs and Helps The Environment Great Mismatch Capability - Gives You The Power You Need For Driving Poor Loads, Allowing You To Select Lower Power Amplifiers And Save You Money Multiple Control Interfaces That Some Of Our Competitors Lack – More Value For Your Money Unsurpassed Harmonic Rejection - Provides More Accurate Measurements Lower Acoustical Noise - Enhances The Work Environment Compact, Lightweight, Modular Designs - Ability To Fit In Small Areas/Chambers And Easily Transportable Intuitive Operation - Saves You Time And Money
Liquid Cooling For Large High-Power RF Amplifiers Temperature is a major factor in determining the reliability of solid state devices used in high-power RF amplifiers. Reducing the temperature that the semiconductor devices see can greatly improve both reliability and performance. Liquid cooling not only allows for lower overall temperatures, but also offers a number of other important advantages: • Liquid cooling reduces the size of the amplifier Air-cooled amplifiers use large metal heat sinks over which air is forced to carry away heat. In a liquid-cooled amplifier, the transistors are mounted on cooling plates through which water flows. The plates are much smaller than heat sinks and because you don’t have to accommodate airflow, they can be built closer together. • Liquid Cooling Reduces The Heat Load On The Amplifier Room Since most of the heat generated is carried away by the cooling liquid, HVAC requirements are reduced, which results in more comfortable surroundings and reduced utility bills. • Liquid Cooling Allows For Fewer Fans This makes the amplifier significantly quieter. By reducing the noise, operators can work in a safer, more pleasant environment without fatigue. • Liquid Cooling Provides The Option Of Using Your Existing Cooling Infrastructure Liquid cooling options include an external chiller or the use of chilled water supplied by the customer’s facility. By utilizing one’s existing infrastructure, operating costs can be greatly reduced. Like everything we do at AR, liquid cooling has been carefully considered, tested and researched before being chosen as the preferred method for controlling temperatures in large high-power amplifiers. We utilize proprietary techniques to implement the most reliable and robust mechanical designs possible.
15
RF Solid State Amplifiers
DC to 1 MHz
DC to 1000 MHz
350AH1
10WD1000
50WD1000
350 watts CW. 10 Hz - 1 MHz.
10 watts CW. dc-1000 MHz.
50 watts CW. dc-1000 MHz.
Operation Class AB Linear Power Output (1.79 Ohm load) CW, min. 350 watts, 10 Hz - 300 kHz 350 - 55 watts, 300 kHz - 1 MHz Voltage Output, min. 25 Vrms, 10 Hz - 300 kHz 25 - 10 Vrms, 300 kHz - 1 MHz Current Output, min. 14 Arms, 10 Hz - 300 kHz 14 - 5.5 Arms, 300 kHz - 1 MHz Flatness ±1.0 dB, 10 Hz - 300 kHz ±4.0 dB, 300 kHz - 1 MHz Frequency Response 10 Hz - 1 MHz instantaneously Input Signal 0 - 2 Vrms Gain (Power) 47 dB min., 10 Hz - 300 kHz 39 dB min., 300 kHz - 1 MHz Gain Control Range 15 dB min. Input Impedance 600 ohms typ. Output Impedance <1Ω typ. Mismatch Tolerance 100% of rated power without fail Primary Power 90 - 260 VAC 47 - 63 Hz, single phase, 1200 watts max. Connectors RF Input Type BNC female on front panel RF Output 5-way binding posts on front panel Remote Control IEEE-488 24 pin female RS-232 9 pin subminiature D female USB Type B female Ethernet RJ-45 Safety Interlock 15 pin subminiature D Cooling Forced air (self contained fans) Weight 25 kg (55 lb) Size (WxHxD) 50.3 x 19.9 x 37.6 cm / 19.8 x 7.85 x 14.8 in
Rated Output Power 10 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 19 watts / Min. 12.5 watts Power Output @ 1dB compression Nominal 17 watts / Min. 10 watts Flatness ±1.0 dB typ. / ±1.5 dB max. Frequency Response DC - 1000 MHz (In two bands selected automatically, manually or buss) Gain 40 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated output power. Will operate without damage or oscillation or foldback with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 10 watts Third Order Intercept Point 50 dBm typ. Primary Power 85 - 264 VAC 47 - 440 Hz, 500 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 Pin Subminiature D Cooling Forced air (self contained fans) Weight 20.5 kg (45 lb) Size (WxHxD) 50.3 x 15.5 x 37.6 cm / 19.8 x 6.1 x 14.8 in
Rated Output Power 50 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 60 watts / Min. 40 watts Power Output @ 1dB compression Nominal 50 watts / Min. 30 watts Flatness ±1.0 dB typ. / ±1.5 dB max. Frequency Response DC - 1000 MHz (in two bands selected automatically or manually) Gain 47 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated output power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 35 watts Third Order Intercept Point 56 dBm typ. Primary Power 90 - 132; 180 - 264 VAC 50 / 60 Hz, single phase, 700 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Control 25 Pin Subminiature D on rear panel Cooling Forced air (self contained fans) Weight 29 kg (64 lb) Size (WxHxD) 50.3 cm x 24.9 cm x 45.7 cm / 19.8 in x 9.8 in x 18 in
350AH1
500
Load Impedance = 1.7 Ohms
10WD1000
25
450
60
20
300
WATTS
WATTS
350 250 200 150
16
Linear @ 1dB Compression
40
Linear @ 1dB Compression
30 20 10
50 0
15
10
100
Linear @ 3dB Compression
50
Linear @ 3dB Compression
WATTS
400
50WD1000
70
10
100
1000
10000
FREQUENCY (Hz)
100000
1000000
* See Application Note #27A at www.arworld.us/appnote27/
5 D.C.
100Hz
1kHz
10kHz 100kHz
1MHz 10MHz 100MHz 1GHz
FREQUENCY (Hz)
0 D.C.
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz 100MHz
FREQUENCY (Hz)
1GHz
10 kHz to 3 MHz
10 kHz to 100 MHz 10 kHz to 225 MHz
800A3B
150A100B
600A225A
800 watts CW. 10 kHz-3 MHz.
150 watts CW. 10 kHz-100 MHz.
600 watts CW. 10 kHz-225 MHz.
Rated Output Power 800 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 800 watts Min. 800 watts, 10 kHz - 2 MHz Min. 700 watts, 2 - 3 MHz Power Output @ 1dB compression Nominal 500 watts / Min. 400 watts Flatness ± 1.0 dB max. Frequency Response 10 kHz - 3 MHz instantaneously Gain (at max. setting) 60 dB min. Gain Adjustment (continuous range) 23 dB min. Input Impedance 50 ohms, nominal Output Impedance (switch select; manual) 12.5, 25, 50, 100, 150, 200, 400 ohms nominal (10 kHz - 3 MHz) on front panel Mismatch Tolerance* Will operate without damage or oscillation with any magnitude and phase of source and load impedance. 100% of rated power without foldback up to 6.0:1 mismatch above which may limit to 400 watts reflected power. Harmonic Distortion Minus 20 dBc max. at 400 watts power output Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Control IEEE-488/RS-232, USB ability to remote control and power an external impedance transformer. RF Power Display 0 - 1000 watts full scale. Directional power monitor allows separate display of forward and reflected power. Power Monitor BNC: 0 - 10V forward and reverse power Cooling Forced air (self contained fans) Primary Power Universal, 85 - 137 / 180 - 264 VAC, 47 - 63 Hz, 2500 watts max. Weight (max.) 36.4 kg (80 lb) Size (WxHxD) 50.3 x 34 x 55.1 cm / 19.8 x 13.4 x 21.7 in For external impedance transformer options, see specification sheet for IT2000 Series impedance transformers.
Rated Output Power 150 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 220 watts / Min. 180 watts Power Output @ 1dB compression Nominal 155 watts / Min. 125 watts Flatness ±1.5 dB max. Frequency Response 10 kHz - 100 MHz instantaneously Gain (at max. setting) 52 dB min. Gain Adjustment Range 18 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, VSWR 2.0:1 max. Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Noise Figure (above 1.0 MHz) 6 dB typ. Harmonic Distortion Minus 20 dBc max. at 125 watts Third Order Intercept Point 58 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC auto ranging 47 - 63Hz, single phase, 1000 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 Pin Subminiature D Cooling Forced air (self contained fans) Weight 31.75 kg (70 lb) Size (WxHxD) 50.3 x 25.2 x 46 cm / 19.8 x 9.9 x 18.1 in
Rated Output Power 600 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 600 watts / Min. 550 watts Power Output @ 1dB compression Nominal 550 watts / Min. 400 watts Flatness ±2.5 dB max. Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 58 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 300 watts reflective power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 400 watts Third Order Intercept Point 65 dBm typ. RF Power Display 0 - 750 watts full scale Primary Power 180 - 264 VAC 47 - 63 Hz 2500 watts max. at .99 P.F. typ. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample BNC female on front panel (coupling factor 60 dB typ.; data supplied) Reverse Sample BNC female on front panel (coupling factor 60 dB typ.) Remote Control IEEE-488 24 pin female on rear panel RS-232 9 pin female Type D on rear panel USB Type B female Safety Interlock 15 pin female Type D on rear panel Cooling Forced air (self contained fans) Weight 45.8 kg (101 lb) Size (WxHxD) 50.3 x 34 x 56.9 cm / 19.8 x 13.4 x 22 in
200
600
150
400
600
200
50
0
0
.005 .01
.05
.2
1
FREQUENCY (MHz)
Linear @ 1dB Compression
100
Linear @ 1dB Compression
3
10
100
PSat
700
Linear @ 3dB Compression
WATTS
800
600A225A
800
250
3dB Compression
WATTS
WATTS
150A100B
800A3B
1000
500
P1dB
400 300 200 100
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0 0.001
0.01
0.1
1
10
FREQUENCY (GHz)
100
1000
17
RF Solid State Amplifiers
10 kHz to 225 MHz 1000A225
2500A225
5000A225
1000 watts CW. 10 kHz-225 MHz. 2500 watts CW. 10 kHz-225 MHz.
1000A225
1600
WATTS
WATTS
800
P1dB
2000
600
1500
400
1000
200
500
0 0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
* See Application Note #27A at www.arworld.us/appnote27/
0 0.001
PSat
5000
2500
P1dB
6000
P3dB
3000
1000
5000A225
7000
3500
1200
Rated Output Power 5000 watts, 10 kHz - 50 MHz 5000 - 4000 watts, 50 MHz - 200 MHz (derating slope from 50 MHz - 200 MHz) 6.66 watts/MHz 3500 watts, 200 MHz - 225 MHz Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 3400 watts, 10 kHz - 100 MHz 3400 - 2500 watts, 100 MHz - 200 MHz (derating slope of 9.0 watts/MHz) 2000 watts, 200 MHz - 225 MHz Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 67 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 2500 watts reflected power, from 10 kHz to 50 MHz. Limited to 2000 watts reflected power from 50 MHz to 225 MHz. Harmonic Distortion Minus 20 dBc max. at 3000 watts Third Order Intercept Point 74 dBm typ. RF Power Display 0 - 7500 watts full scale RF Rise/Fall Time 10 nanoseconds max. Primary Power (user must specify) 187 - 264 VAC Delta (4 wire), Wye compatible 365 - 460 VAC, Wye (5 wire) 47 - 63 Hz, 3-phase 20,000 watts max. at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type EIA 1-5/8 Female on rear panel Forward Sample Type BNC female on front panel Reverse Sample Type BNC female on front panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9-pin female Type D on rear panel Remote Control (fiber optic) ST connector, Tx and Rx RS-232 Cooling Forced air (self contained fans with internal self-contained liquid cooling) Weight 250 kg (550 lb) Size (WxHxD) 56.1 x 88.9 x 160 cm / 22.1 x 35 x 63 in
2500A225
4000 PSat
1400
18
Rated Output Power 2500 watts, 10 kHz - 100 MHz 2500 - 1900 watts, 100 MHz - 225 MHz (derating slope of 4.8 watts/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 2000 watts, 10 kHz - 100 MHz 2000 - 1200 watts, 100 MHz - 225 MHz (derating slope of 6.4 watts/MHz) Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 64 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 1250 watts reflected power. Harmonic Distortion Minus 20 dBc max. at 1800 watts RF Power Display 0 - 3000 watts full scale RF Rise Time/Fall Time 10 nanoseconds max. Primary Power (user must specify) 187 - 264 VAC Delta (4-wire), 3-Phase, 10,000 watts max. 365 - 460 VAC, Wye (5-wire), 47 - 63 Hz Connectors RF Input Type N female on rear panel RF Output Type 7-16 DIN Female on rear panel Forward Sample Type BNC female on front panel Reverse Sample Type BNC female on front panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 15-pin female Type D on rear panel Remote Control (Fiber Optic) ST connector, Tx and Rx RS-232 Cooling Forced air (self contained fans with internal self-contained liquid cooling) Weight 159 kg (350 lb) Size (WxHxD) 56.1 x 108 x 88.9 cm / 22.1 x 42.5 x 35 in
WATTS
Rated Output Power 1000 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 1dB compression Nominal 900 watts / Min. 700 watts Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 60 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 500 watts reflective power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 750 watts Third Order Intercept Point 68 dBm typ. RF Power Display 0 - 2000 watts full scale RF Rise/Fall Time 10 nanoseconds max. Primary Power 187 - 264 VAC 47 - 63 Hz, single phase 5000 watts max. at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type 7-16 DIN Female, on rear panel Forward RF Sample Type BNC female on front panel Reverse RF Sample Type BNC female on front panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9-pin female Type D on rear panel Remote Control (Fiber Optic) ST connector, Tx and Rx RS-232 Safety Interlock 15 pin female Type D on rear panel Cooling Forced air (self contained fans with internal self-contained liquid cooling) Weight 127 kg (280 lb) Size (WxHxD) 56.1 x 109.2 x 88.9 cm / 22.1 x 43 x 35 in
5000 watts CW. 10 kHz-225 MHz.
4000 3000 P1dB
2000 1000
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0 .001
.01
0.1
1
10
FREQUENCY (MHz)
100
10000A225A-A
12500A225
12500A225A-L
10,000 watts CW. 10 kHz-225 MHz.
12,500 watts CW. 10 kHz-225 MHz. 12,500 watts CW. 10 kHz-225 MHz.
Rated Output Power 10,000 watts min., 10 kHz - 100 MHz 10,000 - 6000 watts min., 100 MHz - 225 MHz (derating slope of 32 watt/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 7000 watts, 10 kHz - 100 MHz 7000 - 4000 watts, 100 MHz - 225 MHz (derating slope of 24 watts/MHz) Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 70 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 5000 watts reflected power, from 10 kHz to 100 MHz. Limited to 3000 watts reflected power from 100 MHz to 225 MHz. Harmonic Distortion Minus 20 dBc max. at 6000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 15,000 watts full scale RF Rise/Fall Time 150 nanoseconds max. Primary Power (user must specify) : 187-264 VAC, Wye (5 wire) 380-480 VAC, Delta (4 wire) 47-63 Hz, 3-phase 40,000 watts maximum at .95 P.F. typical Connectors RF Input Type N female on rear panel RF Output Type EIA 1-5/8 male on rear panel Forward Sample Type BNC female on front panel Reverse Sample Type BNC female on front panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9-pin female Type D on rear panel Remote Control (fiber optic) ST Connector, Tx and Rx RS-232 Ethernet RJ-45 Cooling Forced air (self contained fans with internal liquid cooling) Weight 500 kg (1100 lb) Size (WxHxD) 112.1 x 82.4 x 165.3 cm / 44.12 x 32.43 x 65.1 in
Rated Output Power 12,500 watts min., 10 kHz - 100 MHz 12,500 - 8000 watts min., 100 MHz - 225 MHz (derating slope of 36 watt/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 11,000 watts, 10 kHz - 100 MHz 11,000 - 7000 watts, 100 MHz - 225 MHz (derating slope of 32 watts/MHz) Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 71 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 6500 watts reflected power, from 10 kHz to 100 MHz. Limited to 4500 watts reflected power from 100 MHz to 225 MHz. Harmonic Distortion Minus 20 dBc max. at 8000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 15,000 watts full scale RF Rise/Fall Time 10 nanoseconds max. Primary Power (user must specify) 187 - 264 VAC Delta (4 wire), Wye compatible 365 - 460 VAC, Wye (5 wire) 47 - 63 Hz, 3-phase 55,000 watts max. at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type EIA 3-1/8 male on rear panel Forward Sample Type BNC female on front panel Reverse Sample Type BNC female on front panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9-pin female Type D on rear panel Remote Control (fiber optic) ST Connector, Tx and Rx RS-232 Cooling Forced air (self contained fans with internal liquid cooling) Weight 680 kg (1500 lb) Size (WxHxD) 170.2 x 88.9 x 182.8 cm / 67 x 35 x 72 in
10000A225A-A
14000
PSat
12000
12000
4000 2000 0.001
0.01
0.1
1
10
FREQUENCY (MHz)
P1dB
10000
6000
100
1000
PSat
14000
P1dB
10000
WATTS
P1dB
WATTS
WATTS
PSat
12000
8000
12500A225A-L
16000
14000
10000
0
12500A225
16000
Rated Output Power 12,500 watts min., 10 kHz - 100 MHz 12,500 - 6000 watts min., 100 MHz - 225 MHz (derating slope of 52 watt/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 10,000 watts, 10 kHz - 100 MHz 10,000 - 5000 watts, 100 MHz - 225 MHz (derating slope of 40 watts/MHz) Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 70 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 6250 watts reflected power, from 10 kHz to 100 MHz. Limited to 4000 watts reflected power from 100 MHz to 225 MHz. Harmonic Distortion Minus 20 dBc max. at 6000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 15,000 watts full scale RF Rise/Fall Time 150 nanoseconds max. Primary Power (user must specify) 190 - 240 VAC Delta (4 wire) 380 - 480 VAC, Delta (4 wire) 47 - 63 Hz, 3-phase 45,000 watts max. at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type EIA 1-5/8 male on rear panel Forward Sample Type N female on front panel (coupling factor 80dB typical) Reverse Sample Type N female on front panel (coupling factor 80dB typical) Pulse Modulation Input Type BNC female, rear panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9-pin female Type D on rear panel USB 2.0 Type B female, rear Ethernet RJ-45 Cooling Liquid cooled via external chilled water supply Weight (max.) 500 kg (1100 lb) Size (WxHxD) 112.1 x 82.4 x 165.3 cm / 44.12 x 32.43 x 65.1 in Export classification EAR99
8000 6000
8000 6000
4000
4000
2000
2000 0
0 0.00
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
19
RF Solid State Amplifiers
10 kHz to 225 MHz 16000A225A-A
16000A225A-L
20000A225A-L
16,000 watts CW. 10 kHz-225 MHz.
16,000 watts CW. 10 kHz-225 MHz.
20000 watts CW. 10 kHz-225 MHz.
Rated Output Power 16,000 watts min., 10 kHz - 100 MHz 14,000 - 12,000 watts min., 100 MHz - 200 MHz 12,000 watts min., 200 MHz - 225 MHz (derating slope of 22.8 watt/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 14,000 watts, 10kHz - 100MHz 10,000 - 8000 watts, 100MHz - 200MHz (derating slope of 26.66 watts/MHz) 8000 watts 200MHz - 225MHz Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 72 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 8000 watts reflected power from 10kHz-100MHz. Limited to 7000 watts reflected power from 100MHz-225MHz. Modulation Capability Will faithfully reproduce AM, FM or Pulse modulation appearing on the input signal. Harmonic Distortion Minus 20 dBc max. at 10,000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 20,000 watts full scale RF Rise/Fall Time 150 nanoseconds max. Primary Power (user must specify) 380-480 VAC, Delta (4 wire) 47-63 Hz, 3-phase 75,000 watts maximum at .95 P.F. typical Connectors RF Input Type N female on rear panel RF Output Type EIA 3-1/8 male on rear panel Forward Sample N female, front (coupling factor 84dB typical) Reverse Sample N female, front (coupling factor 84dB typical) Pulse Modulation Input BNC female on rear panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488: 24 pin female, rear RS-232: 9 pin female D, rear RS-232 (fiber optic): Type ST, rear USB 2.0: Type B female, rear Ethernet: RJ-45 Cooling Forced air (self contained fans with internal liquid cooling) Weight 997 kg (2200 lb) Size (WxHxD) 226.7 x 99.1 x 177.8 cm / 89.25 x 39 x 70 in Export classification EAR99
Rated Output Power 16,000 watts min., 10 kHz - 100 MHz 15,000 watts min., 100 MHz - 200 MHz 13,000 watts min., 200 MHz - 225 MHz Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 16,000 watts, 10kHz - 100MHz 12,000 watts, 100MHz - 200MHz 10,000 watts 200MHz - 225MHz Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 72.05 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 8000 watts reflected power from 10kHz-100MHz. Limited to 7000 watts reflected power from 100MHz-225MHz. Modulation Capability Will faithfully reproduce AM, FM or Pulse modulation appearing on the input signal. Harmonic Distortion Minus 20 dBc max. at 10,000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 25,000 watts full scale RF Rise/Fall Time 150 nanoseconds max. Primary Power (user must specify) 380-480 VAC, Delta (4 wire) 47-63 Hz, 3-phase 85,000 watts maximum at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type EIA 3-1/8 male on rear panel Forward Sample N female, front (coupling factor 84dB typical) Reverse Sample N female, front (coupling factor 84dB typical) Pulse Modulation Input BNC female on rear panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488: 24 pin female, rear RS-232: 9 pin female D, rear RS-232 (fiber optic): Type ST, rear USB 2.0: Type B female, rear Ethernet: RJ-45 Cooling Liquid cooled via external chilled water supply Weight 997 kg (2200 lb) Size (WxHxD) 226.7 x 99.1 x 177.8 cm / 89.25 x 39 x 70 in Export classification EAR99
Rated Output Power 20,000 watts min., 10 kHz - 100 MHz 16,000 watts min., 100 MHz - 200 MHz 13,000 watts min., 200 MHz - 225 MHz (derating slope of 22.8 watt/MHz) Input For Rated Output 1.0 milliwatt max. Power Output for 1dB compression 16,000 watts, 10kHz - 100MHz 12,000 watts, 100MHz - 200MHz 10,000 watts 200MHz - 225MHz Flatness ±3.0 dB max. ±1.0 dB with internal leveling Frequency Response 10 kHz - 225 MHz instantaneously Gain (at max. setting) 73 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 10,000 watts reflected power from 10kHz-100MHz. Limited to 8000 watts reflected power from 100MHz-225MHz. Modulation Capability Will faithfully reproduce AM, FM or Pulse modulation appearing on the input signal. Harmonic Distortion Minus 20 dBc max. at 12,000 watts Third Order Intercept Point 77 dBm typ. RF Power Display 0 - 25,000 watts full scale RF Rise/Fall Time 150 nanoseconds max. Primary Power (user must specify) 380-480 VAC, Delta (4 wire) 47-63 Hz, 3-phase 85,000 watts maximum at .95 P.F. typ. Connectors RF Input Type N female on rear panel RF Output Type EIA 3-1/8 male on rear panel Forward Sample N female, front (coupling factor 84dB typical) Reverse Sample N female, front (coupling factor 84dB typical) Pulse Modulation Input BNC female on rear panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488: 24 pin female, rear RS-232: 9 pin female D, rear RS-232 (fiber optic): Type ST, rear USB 2.0: Type B female, rear Ethernet: RJ-45 Cooling Liquid cooled via external chilled water supply Weight 997 kg (2200 lb) Size (WxHxD) 226.7 x 99.1 x 177.8 cm / 89.25 x 39 x 70 in Export classification EAR99
PSat
20000
WATTS
WATTS
P1dB
10000
20
P1dB
0
0
0.1
1
10
FREQUENCY (MHz)
100
* See Application Note #27A at www.arworld.us/appnote27/
PSat
20000
10000 5000
0.01
PSat
15000
5000
20000A225A-L
25000
20000
15000
0.001
16000A225A-L
26000
WATTS
16000A225A-A
25000
P1dB
15000 10000 5000 0
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
10 kHz to 250 MHz 25A250A
75A250A
100A250A
25 watts CW. 10 kHz-250 MHz.
75 watts CW. 10 kHz-250 MHz.
100 watts CW. 10 kHz-250 MHz.
Rated Output Power 25 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 32 watts / Min. 25 watts Power Output @ 1dB compression Nominal 20 watts / Min. 15 watts Flatness ±1.0 dB max. Frequency Response 10 kHz - 250 MHz instantaneously Gain (at max. setting) 44 dB min. Gain Adjustment (continuous range) 18 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Noise Figure (above 1.0 MHz) 16 dB typ. Harmonic Distortion Minus 20 dBc max. at 15 watts Third Order Intercept Point 54 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC 47 - 63 Hz, single phase, 200 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Cooling Forced air (self contained fans) Weight 15.9 kg (35 lb) Size (WxHxD) 50.3 x 15.5 x 30 cm / 19.8 x 6.1 x 11.8 in
Rated Output Power 75 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 100 watts / Min. 75 watts Power Output @ 1dB compression Nominal 70 watts / Min. 50 watts Flatness ±1.0 dB max. Frequency Response 10 kHz - 250 MHz instantaneously Gain (at max. setting) 49 dB min. Gain Adjustment (continuous range) 18 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, VSWR 2.0:1 max. Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Noise Figure (above 1.0 MHz) 16 dB typ. Harmonic Distortion Minus 20 dBc max. at 50 watts Third Order Intercept Point 57 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC 47 - 63 Hz, single phase, 400 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 20.5 kg (45 lb) Size (WxHxD) 50.3 x 15.5 x 37.6 cm / 19.8 x 6.1 x 14.8 in
Rated Output Power 100 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 157 watts / Min. 125 watts Power Output @ 1dB compression Nominal 107 watts / Min. 75 watts Flatness ±1.5 dB max. Frequency Response 10 kHz - 250 MHz instantaneously Gain (at max. setting) 50 dB min. Gain Adjustment (continuous range) 18 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, VSWR 2.0:1 max. Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance Noise Figure (above 1.0 MHz) 10 dB typ. Harmonic Distortion Minus 20 dBc max. at 75 watts Third Order Intercept Point 58 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC autoranging 47 - 63 Hz, single phase, 1000 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 31.75 kg (70 lb) Size (WxHxD) 50.3 x 25.2 x 46 cm / 19.8 x 9.9 x 18.1 in
75A250A
25A250A 25A250A
35 35
100A250A
120
200
Linear @ 3dB Compression
Linear @ 3dB Compression
100
Linear@@3dB 3dBCompression Compression Linear
Linear@@1dB 1dBCompression Compression Linear
WATTS
25 25
150
Linear @ 1dB Compression
80
WATTS
WATTS WATTS
30 30
60
100
Linear @ 1dB Compression
40
20 20
50
20
15 15
.01 .01
.05 .1.1 .05
11
1010
FREQUENCY(MHz) (MHz) FREQUENCY
100 250 250 5050 100
1000 1000
0 0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
21
RF Solid State Amplifiers
10 kHz to 250 MHz 10 kHz to 400 MHz 500A250C
75A400
125A400
500 watts CW. 10 kHz-250 MHz.
75 watts CW. 10 kHz-400 MHz.
125 watts CW. 10 kHz-400 MHz.
Rated Output Power 500 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 600 watts / Min. 500 watts Power Output @ 1dB compression Nominal 500 watts / Min. 350 watts Flatness ±2.5 dB max. Frequency Response 10 kHz - 250 MHz instantaneously Gain (at max. setting) 57 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 250 watts reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 350 watts Third Order Intercept Point 65 dBm typ. RF Power Display 0 - 750 watts full scale Primary Power 180 - 264 VAC 47 - 63 Hz, 2500 watts max. @ 0.99 P.F. typ. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample Type BNC female on front panel (coupling factor 60 dB typ.) Reverse Sample Type BNC female on front panel (coupling factor 60 dB typ.) Pulse Modulation Input BNC female on rear panel Safety Interlock 15 pin female Type D on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9 pin female Type D on rear panel RS-232 (Fiber optic) Type ST on rear panel USB Type B female Ethernet RJ-45 Cooling Forced air (self contained fans) Weight 45.8 kg (101 lb) Size (WxHxD) 50.3 x 34 x 56.9 cm / 19.8 x 13.4 x 22 in
Rated Output Power 75 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 100 watts / Min. 75 watts Power Output @ 1dB compression Nominal 75 watts / Min. 50 watts Flatness ±1.5 dB max. Frequency Response 10 kHz - 400 MHz instantaneously Gain (at max. setting) 49 dB min. Gain Adjustment (continuous range) 18 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, VSWR 2.0:1 max. Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Noise Figure (above 1.0 MHz) 6 dB typ. Harmonic Distortion Minus 20 dBc max. at 50 watts Third Order Intercept Point 57 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC 47 - 63 Hz, single phase, 400 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 23.4 kg (51.5 lb) Size (WxHxD) 50.3 x 15.5 x 37.6 cm / 19.8 x 6.1 x 14.8 in
Rated Output Power 125 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 140 watts / Min. 75 watts Power Output @ 1dB compression Nominal 100 watts / Min. 75 watts Flatness ±2.0 dB max. Frequency Response 10 kHz - 400 MHz instantaneously Gain (at max. setting) 51 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 62.5W reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Pulse Mode Gating Characteristics Signal (into 50 ohms) +3.0 to 6.0 VDC Harmonic Distortion Minus 20 dBc max. at 75 watts Third Order Intercept Point 62 dBm typ. Primary Power 85 - 264 VAC 47 - 63 Hz, 600 watts max. @ 0.99 P.F. typ. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample SMA female on rear panel (coupling factor 50 dB typ.) Reverse Sample SMA female on rear panel (coupling factor 50 dB typ.) Pulse Modulation Input BNC female on rear panel Remote Control IEEE-488 24 pin female on rear panel RS-232 9 pin female Type D on rear panel RS-232 (Fiber optic) Type ST USB Type B female Ethernet RJ-45 Safety Interlock 15 pin female Type D on rear panel Cooling Forced air (self contained fans) Weight 20.6 kg (45 lb) Size (WxHxD) 50.3 x 16.3 x 56.4 cm / 19.8 x 6.4 x 22.2 in
75A400
500A250C
120
P - 3dB
700
WATTS
WATTS
500
P - 1dB
400 300
Linear @ 1dB Compression
80 60
0 0.001
0
0.01
0.1
1
10
FREQUENCY (MHz)
100
* See Application Note #27A at www.arworld.us/appnote27/
120
P 1dB
100 80 60 40
20
100
P 3dB
140
40
200
22
160
100
600
125A400
180
Linear @ 3dB Compression
WATTS
800
20 0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
10 kHz to 400 MHz
100 kHz to 400 MHz
200A400A
400A400B
150A400
200 watts CW. 10 kHz-400 MHz.
400 watts CW. 10 kHz-400 MHz.
150 watts CW. 100 kHz-400 MHz.
Rated Output Power 200 watts, 10 kHz - 250 MHz 200 -175 watts, 250 MHz - 400 MHz (derated slope of .167W/MHz) Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 175 watts, 10 kHz -250 MHz 175-150 watts, 250 MHz-400 MHz (derated slope of .167W/MHz) Power Output @ 1dB compression Nominal 150 watts, 10 kHz - 250 MHz 150-125 watts, 250 MHz - 400 MHz (derated slope of .167W/MHz) Flatness ±3.5 dB max. Frequency Response 10 kHz - 400 MHz instantaneously Gain (at max. setting) 53 dB min. Gain Adjustment Range 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 100W reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Pulse Mode Gating Characteristics Signal (into 50 ohms) +3.0 to 6.0 VDC Harmonic Distortion Minus 20 dBc max. at 100 watts Third Order Intercept Point 65 dBm typ. Primary Power 180 - 264 VAC 47 - 63 Hz, 1250 watts max. @ 0.99 P.F. typ. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample BNC female on front panel (coupling factor 60 dB typ.; data supplied) Reverse Sample BNC female on front panel (coupling factor 60 dB typ.) Remote Control IEEE-488 24 pin female on rear panel RS-232 9 pin female Type D on rear panel USB Type B female Safety Interlock 15 pin female Type D on rear panel Cooling Forced air (self-contained fans) Weight 45.8 kg (101 lb) Size (WxHxD) 50.3 x 34 x 56.9 cm / 19.8 x 13.4 x 22 in
Rated Output Power 400 watts, 10 kHz - 250 MHz 300 watts minimum from 250MHz-400MHz Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression 400 watts minimum from 10kHz-200MHz 250 watts minimum from 200MHz-400 MHz Power Output @ 1dB compression 350 watts minimum from 10kHz-200MHz 200 watts minimum from 200MHz-400MHz Flatness ±3.0 dB max. Frequency Response 10 kHz - 400 MHz instantaneously Gain (at max. setting) 56 dB min. Gain Adjustment Range 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% rated power without foldback up to 6.0:1 mismatch, above which may limit to 200W reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 250 watts Third Order Intercept Point 65 dBm typ. Primary Power 180 - 264 VAC 47 - 63 Hz, 2500 watts max. @ 0.99 P.F. typ. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample BNC female on front panel (coupling factor 60 dB typ.; data supplied) Reverse Sample BNC female on front panel (coupling factor 60 dB typ.) Remote Control IEEE-488 24 pin female on rear panel RS-232 9 pin female Type D on rear panel USB Type B female Safety Interlock 15 pin female Type D on rear panel Cooling Forced air (self-contained fans) Weight 45.8 kg (101 lb) Size (WxHxD) 50.3 x 34 x 56.9 cm / 19.8 x 13.4 x 22 in
Rated Output Power 150 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 155 watts / Min. 130 watts Power Output @ 1dB compression Nominal 125 watts / Min. 100 watts Flatness ±1.5 dB max. Frequency Response 100 kHz - 400 MHz instantaneously Gain (at max. setting) 52 dB min. Gain Adjustment Range 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 100 watts Third Order Intercept Point 58 dBm typ. Primary Power 90 - 135 / 180 - 270 VAC auto ranging 47 - 63Hz, single phase, 1000 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 36 kg (80 lb) Size (WxHxD) 50.3 x 25.2 x 46 cm / 19.8 x 9.9 x 18.1 in
200A400A
250
150
300
P1dB
WATTS
350
WATTS
WATTS
Linear @ 3dB Compression
400
150
P1dB
250 200
100
150
Linear @ 1dB Compression 100
50
100
50
150A400
200
PSat
450
200
0
400A400B
500 PSat
50 0 0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
0
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
100
1000
23
RF Solid State Amplifiers
100 kHz to 1000 MHz 500 kHz to 1000 MHz 1 MHz to 1000 MHz 1W1000B
10W1000C
30W1000B
1 watt CW. 100 kHz-1000 MHz.
10 watts CW. 500 kHz-1000 MHz.
30 watts CW. 1-1000 MHz.
Rated Output Power 1.0 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 2.5 watts / Min. 1.0 watts Power Output @ 1dB compression Nominal 2 watts / Min. 1.0 watts Flatness ±0.5 dB typ. / ±1.0 dB max. Frequency Response 100 kHz - 1000 MHz instantaneously Gain (at max. setting) 30 dB min. Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 1.0 watts Third Order Intercept Point 42 dBm typ. Primary Power 90 - 264 VAC 47 - 440 Hz, single phase, 60 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Cooling Forced air (self-contained fan) Weight 4.5 kg (10 lb) Size (WxHxD) 26 x 11.7 x 21.6 cm / 10.3 x 4.6 x 8.5 in
Rated Output Power 10 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 20 watts / Min. 10 watts Power Output @ 1dB compression Nominal 17 watts / Min. 10 watts Flatness ±1.0 dB typ. / ±1.5 dB max. Frequency Response 500 kHz - 1000 MHz instantaneously Gain (at max. setting) 40 dB min. Gain Adjustment (continuous range) 20 dB min. (4096 steps remote) Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 10 watts Third Order Intercept Point 50 dBm typ. Primary Power 90 - 132, 180 - 264 VAC 50 / 60 Hz, single phase, 300 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 Pin Subminiature D Cooling Forced air (self contained fans) Weight 20.5 kg (45 lb) Size (WxHxD) 50.3 x 15.5 x 37.6 cm / 19.8 x 6.1 x 14.8 in.
Rated Output Power 30 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 36 watts / Min. 30 watts Power Output @ 1dB compression Nominal 27 watts / Min. 20 watts Flatness ±1.0 dB typ. / ±1.5 dB max. Frequency Response 1 - 1000 MHz instantaneously Gain (at max. setting) 45 dB min. Gain Adjustment (continuous range) 20 dB min. (4096 steps remote) Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 25 watts Third Order Intercept Point 52 dBm typ. Primary Power 90 - 132, 180 - 264 VAC 50 / 60 Hz, single phase, 325 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Safety Interlock 15 Pin Subminiature D Cooling Forced air (self contained fans) Weight 20.5 kg (45 lb) Size (WxHxD) 50.3 x 15.5 x 37.6 cm / 19.8 x 6.1 x 14.8 in
1W1000B
3
Linear @ 3dB Compression
1.5
40
15
Linear @ 1dB Compression
WATTS
WATTS
WATTS
Linear @ 1dB Compression
2
10 5
1 0.01
0.1
1
30W1000B
50
20
2.5
24
10W1000C
25
Linear @ 3dB Compression
10
FREQUENCY (MHz)
100
1000
* See Application Note #27A at www.arworld.us/appnote27/
0
Linear @ 3dB Compression
30 Linear @ 1dB Compression
20 10
0.1
1
10
100
FREQUENCY (MHz)
1000
10000
0 0.1
1
10
100
FREQUENCY (MHz)
1000
10000
20 to 1000 MHz
50 MHz to 1000 MHz
100W1000C
2W1000
50W1000C
100 watts CW. 1-1000 MHz.
2 watts CW. 20-1000 MHz.
50 watts CW. 50-1000 MHz.
2 watts min. Rated Output Power 100 watts Rated Output Power 1.0 milliwatt max. Input For Rated Output 1.0 milliwatt max. Input For Rated Output Power Output @ 3dB compression Power Output @ 3dB compression Nominal 3.0 watts / Min. 2.5 watts Nominal 123 watts / Min. 100 watts Power Output @ 1dB compression Power Output @ 1dB compression Nominal 2.5 watts / Min. 2.0 watts Nominal 95 watts / Min. 75 watts Flatness Flatness ±1.0 dB typ. / 1.5 dB max. ±2.0 dB max. / 1.5 dB typ. ±0.8 dB with internal leveling Frequency Response 20 - 1000 MHz instantaneously Frequency Response Gain (at max. setting) 33 dB min. 1 - 1000 MHz instantaneously Gain Adjustment (continuous range) 20 dB min. Gain (at max. setting) 50 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Gain Adjustment (continuous range) Output Impedance 50 ohms, nominal 18 dB min. (4096 steps remote) Mismatch Tolerance* Input Impedance 50 ohms, VSWR 2.0:1 max. 100% of rated power without foldback. Will operate without Output Impedance 50 ohms, nominal damage or oscillation with any magnitude and phase of source and load impedance. Mismatch Tolerance* Will operate without damage or oscillation with any magnitude Spurious Minus 73 dBc typ. and phase of source and load impedance. Will limit reflected Harmonic Distortion Minus 20 dBc max. at 2 watts power to 100 watts. Minus 30dBc typ. Harmonic Distortion Minus 20 dBc max. at 80 watts Third Order Intercept Point 45 dBm typ. Third Order Intercept Point 58 dBm typ. Noise Figure 8 dB max., 6 dB typ. RF Power Display 0 - 200 watts Primary Power Primary Power 90 - 264 VAC 90 - 264 VAC 50 / 60 Hz, 50 watts 40 / 400 Hz, single phase, 1200 watts max. Connectors Connectors RF Input Type N female on front panel RF Input Type N female on front panel RF Output Type N female on front panel RF Output Type N female on front panel Cooling Forced air (self contained fans) Remote Interfaces Weight 4.5 kg (10 lb) IEEE-488 24 pin female Size (WxHxD) RS-232 9 pin Subminiature D (female) 26 x 11.4 x 28.2 cm / 10.25 x 4.5 x 11.1 in Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 40 kg (88 lb) Size (WxHxD) 50.3 x 24.9 x 53 cm / 19.8 x 9.8 x 21.1 in
100W1000C
160
100
3.8
80 60
P3dB
3.4 3
WATTS
WATTS
Linear @ 1dB Compression
100
P1dB
2.6
Linear @ 3dB Compression
80 60
Linear @ 1dB Compression
2.2
40
40
1.8
20
1.4
0
0
0
0
0 0 10 0 50 10
95
90
85
0
0
0
0
0
FREQUENCY (MHz)
80
75
70
65
60
55
0
20
0
1000
50
900
0
800
45
700
0
600
40
500
0
400
FREQUENCY (MHz)
35
300
0
200
30
100
0
1 20
25
10000
0
1000
20
100
15
10
FREQUENCY (MHz)
10
1
50 80
WATTS
50W1000C 120
4.2
120
0 0.1
2W1000
5 4.6
Linear @ 3dB Compression
140
Rated Output Power 50 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 70 watts / Min. 55 watts Power Output @ 1dB compression Nominal 60 watts / Min. 45 watts Flatness ±1.0 dB typ. / ±1.5 dB max. Frequency Response 50 - 1000 MHz instantaneously Gain (at max. setting) 48 dB min. Gain Adjustment (continuous range) 20 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 50 watts, Minus 30 dBc typical at 50 watts Spurious Minus 73 dBc typical Third Order Intercept Point 55 dBm typ. Noise Figure 8 dB max, 6 dB typ. Primary Power 90 - 264 VAC 50 / 60 Hz, single phase, 250 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Fiber optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 Pin Subminiature D Cooling Forced air (self contained fans) Weight 17.3 kg (38 lb) Size (WxHxD) 50.3 x 15.5 x 55.1 cm / 19.8 x 6.1 x 21.7 in Export classification EAR99
25
RF Solid State Amplifiers
80 to 1000 MHz 125W1000
150W1000A
250W1000B
125 watts CW. 80-1000 MHz.
150 watts CW. 80-1000 MHz.
250 watts CW. 80-1000 MHz.
Rated Output Power 125 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 130 watts / Min. 110 watts Power Output @ 1dB compression Nominal 110 watts / Min. 85 watts Flatness ±1.5 dB typ. / 2.0 dB max. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 51 dB min. Gain Adjustment (continuous range) 25 dB min. (4096 steps remote) Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 1 00% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Spurious Minus 73 dBc typ. Harmonic Distortion Minus 25 dBc max. at 100 watts Minus 30dBc typ. at 100 watts Third Order Intercept Point 58 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power 90 - 264 VAC 50 / 60 Hz, single phase, 625 watts Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D female Fiber optic ST Conn Tx and Rx RS-232 USB 2.0: Type B Ethernet RJ-45 Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 36 kg (80 lb) Size (WxHxD) 50.3 x 24.9 x 61 cm / 19.8 x 9.8 x 24 in
Rated Output Power 150 watts Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 140 watts / Min. 120 watts Power Output @ 1dB compression Nominal 120 watts / Min. 100 watts Flatness ±2.0 dB max. / 1.5 dB typ. ±0.8 dB with internal leveling Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 52 dB min. Gain Adjustment (continuous range) 18 dB min. (4096 steps remote) Input Impedance 50 ohms, VSWR 2.0:1 max. Output Impedance 50 ohms, nominal Mismatch Tolerance* Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Will limit reflected power to 100 watts. Harmonic Distortion Minus 20 dBc max. at 100 watts Third Order Intercept Point 58 dBm typ. RF Power Display 0 - 200 watts Primary Power 90 - 264 VAC 40 / 400 Hz, single phase, 1200 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Remote Interfaces IEEE-488 24 pin female RS-232 9 pin Subminiature D (female) Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin Subminiature D Cooling Forced air (self contained fans) Weight 40 kg (88 lb) Size (WxHxD) 50.3 x 24.9 x 53 cm / 19.8 x 9.8 x 21.1 in
Rated Output Power 250 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 300 watts / Min. 250 watts Power Output @ 1dB compression Nominal 250 watts / Min. 200 watts Flatness ±1.5 dB max. / ±1.0 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 54 dB min. Gain Adjustment (continuous range) 25 dB min. (4096 steps remote) Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. (See Application Note #27) Harmonic Distortion Minus 20 dBc max. at 200 watts, -20 dBc typ. @ 250 watts Third Order Intercept Point 62 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power 120 - 240 VAC 50 / 60 Hz, single phase, 1000 watts max. Connectors RF Input Type N female on front panel RF Output Type N female on front panel Forward Sample BNC female, front (-46 dBc) Reverse Sample BNC female, front (-46 dBc) Remote Interfaces IEEE-488 24 pin female RS-232 9 pin subminiature D female Fiber Optic ST connector, Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Cooling Forced air (self contained fans) Weight 40 kg (88 lb) Size (WxHxD) 50.3 x 24.9 x 61 cm / 19.8 x 9.8 x 24 in
125W1000
Psat
P1dB
110
390 350
WATTS
P3dB
130
Linear @ 3dB Compression
160
WATTS
WATTS
150
140 120
Linear @ 1dB Compression
310
P3dB P1dB
100
230
70
80
190
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
* See Application Note #27A at www.arworld.us/appnote27/
60
0
200
400
600
FREQUENCY (MHz)
800
1000
Psat
270
90
50 50
26
430
180
170
250W1000B
150W1000A
200
190
150 70
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
500W1000B
750W1000
1000W1000E
500 watts CW. 80-1000 MHz.
750 watts CW. 80-1000 MHz.
1000 watts CW. 80-1000 MHz.
Rated Output Power 500 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 575 watts, 525 watts min. up to 500 MHz; 475 watts min. from 500 to 1000 MHz Power Output @ 1dB compression Nominal 500 watts, 450 watts min. up to 500 MHz; 400 watts min. from 500 to 1000 MHz Flatness ±1.5 dB max. / ±1.0 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 57 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typical. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. (See Application Note #27) Harmonic Distortion Minus 20 dBc max. at 400 watts, -20 dBc typ. at 500 watts Third Order Intercept Point 63 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (specify voltage): 120-240 VAC, 50/60 Hz, single phase, 2200 watts Connectors RF Input Type N on front panel RF Output Type N female on front panel Forward Sample BNC female, front (-50 dBc) Reverse Sample BNC female, front (-50 dBc) Safety Interlock 15 pin subminiature D on rear panel USB 2.0 Type B Ethernet RJ-45 Cooling Forced air (self contained fans), enters front and bottom Weight 86.2 kg (190 lb) Size (WxHxD) 50.3 x 47 x 61 cm / 19.8 x 18.5 x 24 in
Rated Output Power 750 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 900 watts / 775 watts min. up to 500 MHz; 725 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 750 watts / 700 watts min. up to 500 MHz; 600 watts from 500 to 1000 MHz Flatness ±1.5 dB max. / ±1.0 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 58.8 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 600 watts, -20 dBc typ. at 750 watts Third Order Intercept Point 64 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (user must specify) 200 - 240 VAC 50 / 60 Hz, single phase, 3200 watts Connectors RF Input Type N female on front panel RF Output Type 7/16 female on rear panel Forward Sample BNC female, front (-60 dBc) Reverse Sample BNC female, front (-60 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 120 kg (263 lb) Size (WxHxD) 50.3 x 108 x 83 cm / 19.8 x 42.5 x 32.4 in
Rated Output Power 1000 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 1200 watts / 1100 watts min. up to 500 MHz; 950 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 950 watts, 950 watts min up to 500 MHz, 800 watts from 500 to 1000 MHz Flatness ±1.5 dB max; ±1.0 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 60 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. (See Application Note #27) Harmonic Distortion Minus 20 dBc max. at 800 watts, -20 dBc typ. @ 1000 watts Third Order Intercept Point 66 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power 200 - 240 VAC, 50 / 60 Hz, single phase, 5000 watts Connectors RF Input Type N female on front panel RF Output Type 7/16 female on rear panel Forward Sample BNC female, front (-60 dBc) Reverse Sample BNC female, front (-60 dBc) Safety Interlock 15 pin subminiature D on rear panel USB 2.0 Type B Ethernet RJ-45 Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 124.8 kg (275 lb) Size (WxHxD) 50.3 x 108 x 83 cm / 19.8 x 42.5 x 32.4 in
750 700
1400
900
1300
WATTS
WATTS
Psat
600
P3dB
550 500
P1dB
450 400 70
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
Psat
800
P3dB
700
P1dB
500
900
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
P1dB
1100 1000
70
Psat P3dB
1200
600
400
1000W1000E
1500
1000
650
350
750W1000
1100
WATTS
500W1000B
800
800 70
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
27
RF Solid State Amplifiers
80 to 1000 MHz 1500W1000
2000W1000C
3000W1000B
1500 watts CW. 80 -1000 MHz.
2000 watts CW. 80 -1000 MHz.
3000 watts CW. 80-1000 MHz.
Rated Output Power 1500 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 1600 watts / 1500 watts min. up to 500 MHz; 1300 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 1400 watts / 1300 watts min. up to 500 MHz; 1200 watts min. from 500 to 1000 MHz Flatness ±2.0 dB max. / ±1.5 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 61.8 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 1200 watts, -20 dBc typ. at 1500 watts Third Order Intercept Point 68 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (user must specify) 200 - 240 VAC 50 / 60 Hz, 3 phase, 7000 watts Connectors RF Input Type N female on rear panel RF Output Type 1 5/8 female on rear panel Forward Sample Type N female, front (-63 dBc) Reverse Sample Type N female, front (-63 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 182 kg (400 lb) Size (WxHxD) 56.1 x 175.3 x 97.6 cm / 22.1 x 69 x 38.4 in
Rated Output Power 2000 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 2100 watts / 2000 watts min. up to 500 MHz; 1650 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 1850 watts / 1750 watts min. up to 500 MHz; 1400 watts min. from 500 to 1000 MHz Flatness ±2.0 dB max. / ±1.5 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 63 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 1600 watts, -20 dBc typ. at 2000 watts Third Order Intercept Point 70 dBm typ. Primary Power (user must specify) 200 - 240 VAC 50 / 60 Hz, 3 phase, 9000 watts Connectors RF Input Type N female on rear panel RF Output Type 1 5/8 female on rear panel Forward Sample BNC female, front (-60 dBc) Reverse Sample BNC female, front (-60 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans) Weight (approximate) 218 kg (480 lb) Size (WxHxD) (3 cabinets) 56.1 x 173 x 82.3 cm / 22.1 x 68 x 32.4 in
Rated Output Power 2800 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 3000 watts / 2600 watts min. up to 500 MHz; 2400 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 2500 watts / 2250 watts min. up to 500 MHz; 1850 watts from 500 to 1000 MHz Flatness ±2.0 dB max. / ±1.5 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 64.8 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback up to 6.0:1 mismatch above, which may limit to 1500 watts reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 2400 watts, -20 dBc typ. at 3000 watts Third Order Intercept Point 72 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (user must specify) 200 - 240 VAC 360-435 VAC Wye connected (5-wire) 50 / 60 Hz, 3 phase, 14kVA Connectors RF Input Type N female on rear panel RF Output Type 1 5/8 female on rear panel Forward Sample BNC female, front (-68 dBc) Reverse Sample BNC female, front (-68 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 364 kg (800 lb) Size (WxHxD) (2 joined cabinets) 111.8 x 177.8 x 82.3 cm / 44 x 70 x 32.4 in
2600
1800
1400
WATTS
WATTS
P3dB P1dB
1200
3600
P1dB
2000 1800 1600
1000
28
P3dB
2200
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
* See Application Note #27A at www.arworld.us/appnote27/
1200 70
Psat
3200
P3dB
P1dB
2800 2400
1400
100
3000W1000B
4000
Psat
2400
Psat
1600
800 70
2000W1000C
2800
WATTS
1500W1000
2000
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
2000 70
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
4000W1000B
10000W1000A
4000 watts CW. 80-1000 MHz.
10000 watts CW. 80-1000 MHz.
Rated Output Power 3700 watts min. Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 4000 watts / 3600 watts min. up to 500 MHz; 3400 watts from 500 to 1000 MHz Power Output @ 1dB compression Nominal 3500 watts / 3000 watts min. up to 500 MHz; 2500 watts from 500 to 1000 MHz Flatness ±2.0 dB max. / ±1.5 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 66 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback up to 6.0:1 mismatch above, which may limit to 2000 watts reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. Harmonic Distortion Minus 20 dBc max. at 3400 watts, -20 dBc typ. at 4000 watts Third Order Intercept Point 73 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (user must specify) 200 - 240 VAC 360-435 VAC Wye connected (5-wire) 50 / 60 Hz, 3 phase, 17.5kVA Connectors RF Input Type N female on rear panel RF Output Type 1 5/8 female on rear panel Forward Sample BNC female, front (-60 dBc) Reverse Sample BNC female, front (-60 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 432 kg (950 lb) Size (WxHxD) (2 joined cabinets) 111.8 x 177.8 x 82.3 cm / 44 x 70 x 32.4 in
Rated Output Power Nominal, 12500 watts 12000 watts min. up to 700 MHz 10500 watts min., 700 to 1000 MHz Input For Rated Output 1.0 milliwatt max. Power Output @ 3dB compression Nominal 12500 watts / 12000 watts min. up to 700 MHz; 10000 watts from 700 to 1000 MHz Power Output @ 1dB compression Nominal 11000 watts / 10500 watts min. up to 700 MHz; 9500 watts from 700 to 1000 MHz Flatness ±2.0 dB max. / ±1.5 dB typ. Frequency Response 80 - 1000 MHz instantaneously Gain (at max. setting) 70 dB min. Gain Adjustment (continuous range) 25 dB min. Input Impedance 50 ohms, VSWR 1.5:1 max.; 1.3:1 typ. Output Impedance 50 ohms, nominal Mismatch Tolerance* 100% of rated power without foldback, up to 6.0:1. Mismatch above which may limit to 6000 watts reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. *See Application Note #27. Modulation Capability* Faithfully reproduces AM,FM, or Pulse modulation appearing on input signal. Harmonic Distortion Minus 20 dBc max. at 10000 watts, -25 dBc typ. at 10000 watts Third Order Intercept Point 78 dBm typ. Noise Figure 8 dB max., 6 dB typ. Primary Power (specify voltage) 200-240 VAC Delta connected (4-wire), 360-435 VAC Wye connected (5-wire) 50/60 Hz, three phase, 48000W Connectors RF Input Type N female on rear panel RF Output Type 4-1/16 EIA, rear panel Forward Sample N female, front (-70 dBc) Reverse Sample N female, front (-70 dBc) Remote Interfaces: IEEE-488 24-pin female RS-232 9-pin Subminiature D, female Fiber Optic ST Conn Tx and Rx RS-232 USB 2.0 Type B Ethernet RJ-45 Safety Interlock 15 pin female subminiature D, rear panel Cooling Forced air (self contained fans), enters front and bottom Weight (approximate) 703 kg (1550 lbs) Size (WxHxD) 170 x 183 x 99 cm / 67 x 72 x 39 in Export classification EAR99
4000W1000B
5000
10000W1000A 15500 14500
4600
13500
Psat P3dB
3800
P1dB
3400
12500
Psat
11500
P3dB
10500
P1dB
9500
3000 2600 70
WATTS
WATTS
4200
8500
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
7500 70 80 100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000 1050
29
