Transcript
RANGE EXTENDER FOR OEM GM REMOTE STARTER
TRX72N TX557
TX447
Installation Manual RFTD
XK01
STEP 1 : VEHICLE COMPATIBILITY
Internet *INTERFACE SOLD SEPARATELY
USB CABLE USB PORT
USB ADAPTOR
Downloadable Firmware for Platform XK01: GMDL5X, GMDL6X, GMDL7X IMPORTANT: Latest firmware can be downloaded at www.xpressdownload.com NOTE: Default firmware on the XK1 platform is GMDL6X. If the vehicle you are working in is not in the GMDL6X list, you will need to reprogram the XK1 platform with the desired firmware.
GMDL6X
GMDL5X Buick Terrazza Chevrolet Cobalt Chevrolet Malibu/Maxx Chevrolet Uplander Pontiac G6 Pontiac Montana SV6 Pontiac Pursuit Saturn Relay
2005-2007 2005-2006 2004-2006 2005-2007 2005-2006 2005-2007 2005-2006 2005-2007
GMDL7X Chevrolet Cobalt Chevrolet Malibu/Maxx Pontiac G6 Pontiac Pursuit/G5 Pontiac Solstice Chevrolet Malibu/Maxx
2007 2007 2007 2007 2007 2007
Buick Lucerne Cadillac Escalade Chevrolet Avalanche Chevrolet Equinox Chevrolet Impala Chevrolet Monte Carlo Chevrolet Silverado Chevrolet Suburban Chevrolet Tahoe GMC Acadia GMC Sierra GMC Yukon Pontiac Torrent Saturn Outlook
2006-2007 2007 2007 2007 2006-2007 2006-2007 2007 2007 2007 2007 2007 2007 2007 2007
STEP 2: RFTD WIRING DIAGRAM & INSTALLATION
WIRING DIAGRAM
HARNESS #2
LED
OR
HARNESS #1
XL201-RFTD 2 WAY
RED
2WAY ANTENNA (TRX72N)
BLACK
Programming Button
*INTERFACE SOLD SEPARATELY
HARNESS #1
XTR-LINK-RFTD 1 WAY
RED
1WAY ANTENNA (RX57)
BLACK
Programming Button
HARNESS #2
LED
INSTALLATION 1. Connect antenna to XL-RFTD module with harness #1. 2. Connect XK module* to XL-RFTD to the white 4 pin connector using harness #2. 3. Follow the XK module* installation instructions to complete installation. (See page 4 for XK01-GMDL5X or page 6 for XK01-GMDL6X, GMDL7X)
2
STEP 3 : TRANSMITTER PROGRAMMING / LED CONFIRMATION
TRANSMITTER PROGRAMMING 1. Press and hold the programming button of the XL-RFTD. 2. Press any button on the transmitter to program it to the XL-RFTD. 3. When the LED from the XL-RFTD turns off, release programming button. 4. Repeat steps 1 to 3 to program extra transmitters. FOR 2WAY TRANSMITTERS: The 2WAY transmitter will confirm the number of transmitters that are programmed by tone. (1 remote = 1 Beep, 2 remotes = 2 Beeps, etc). Maximum 4 remote can be programmed.
LED STATUS/CONFIRMATION # OF FLASH
RATE
1
FAST
Confirms programmed transmitter. (IN PROGRAMMING MODE)
FAST
Button from programmed 1WAY transmitter was pressed; system confirmed signal.
1 1 1
DESCRIPTION
FAST, then SLOW Button from programmed 2WAY transmitter was pressed; system confirmed signal. SLOW
Tranmission of a signal to a 2WAY transmitter.
STEP 4 : TRANSMITTER FUNCTION
1WAY TRANSMITTER(S) Fonction de la télécommande A single press of the UNLOCK button will unlock driver’s door. Parking lights will flash and interior dome light illuminates.
A single press of the LOCK button will lock all power doors. A second press of this button within 3 secs. will confirm the LOCK command by a chirp of the vehicle’s horn. A Press & Hold of the LOCK button for more than 3 seconds will also activate PANIC MODE. The horn will sound and parking lights will flash for 30 seconds.
A second press of this button within 3 secs. will unlock all doors.
TX447
TX557
To remote start the vehicle Press and release the LOCK button on the transmitter, then immediately press the STAR button. The vehicle parking lights will be illuminated to indicate that the engine is running and will run for 10 minutes.
To deactivate this function: - Press again on this button - Waiting for the end of 30 seconds delay - Start vehicle.
To increase engine run time: While the vehicle is running with remote starter, press and release the transmitter LOCK button, then press the start button. This will extend running time for 10 minutes.
To remote stop the engine: Press the STAR button 1 time and release, the engine will stop. The parking lights will flash 2 times to confirm.
The TRUNK button is used to open the power trunk/hatch. Press & Hold this button for 2 seconds; then release. The vehicle’s parking lights will flash 3 times to confirm. (OPTIONAL)
2WAY TRANSCEIVER
TRX722-2 ICON STATUS REFERENCE CHART 2
Lock/Unlock Confirmation
Vibration
Open trunk detected
*
Open door(s) detected
*
Start successfully
*
Second car Operation
* Available on specific vehicle only
3
XK01-GMDL5X - WIRING DIAGRAM & VEHICLE REFERENCE CHART
XK01-GMDL5X Connection of the XK module in Range Extender mode for GM OEM remote starter Internet USB CABLE USB PORT
USB ADAPTOR
IMPORTANT: Latest firmware can be downloaded at www.xpressdownload.com
RED
HARNESS #2
XTR-LINK-RFTD 1 WAY
BLACK
Programming Button
WIRING DIAGRAM
1WAY ANTENNA (RX57)
HARNESS #1
LED
OR BLACK
XL201-RFTD 2 WAY
Programming Button
2WAY ANTENNA (TRX72N)
HARNESS #1
LED
Data Wire Connects to OBDII PIN 2
10 PIN HARNESS
XK01-GMDL5X
D2D
RED
HARNESS #2
N/C
Brown
N/C
N/C
Green
N/C
Blue
N/C
N/C
Violet/White Violet
DATA DATA
(-)
N/C OUTPUT
(-)
INPUT
(+)
Red
INPUT
(-)
Black
8
9
16
Retained Accessory Power (RAP) & Rearm at BCM - (See chart below) Data Input to OBDII
Data Output at BCM - (See chart below)
Pink/White Pink
1
N/C
Orange
Negative Parking trigger for Remote start confirmation (2 way) at BCM - (See chart Below)
(+)12 Volt Constant Chassis Ground
Programming Button
VEHICLE WIRING REFERENCE CHART VEHICLE Model & Year
BCM LOCATION
RAP & REARM WIRE DATA OUTPUT WIRE (Violet/White from module) (Pink/White from module) Color & Location Color & Location
PARKING LIGHT WIRE (Orange from module) Color & Location
Cobalt 2005-2006 Pursuit 2005-2006
center console
Gray/Black wire at BCM: J1 Connector - pin 22
Tan/White wire at BCM: C2 connector - pin 12
Brown/White wire at BCM: C2 connector, PIN 5
Malibu G6
2004-2006 2005-2006
center console
Gray/Black wire at BCM: J1 Connector - pin 51
Light Green wire at BCM: C2 connector - pin 12
Brown/White wire at BCM: C2 connector, PIN 5
Uplander 2005-2007 Terraza 2005-2007 Relay 2005-2007 Sv6 2005-2007
left side of steering column
Tan wire at BCM: C2 Connector - pin 25
Tan/White wire at BCM: C1 connector - pin 37
Brown/White wire at BCM: C1 connector, PIN 10
VEHICLE PROGRAMMING - When module is properly connected, press lock or unlock on original transmitter (OEM). (If no transmitter’s available, pulse orange wire to ground.) Module is now programmed.
4
XK01-GMDL5X - OPTION PROGRAMMING USER SETTINGS: OPTION PROGRAMMING 1-Key “OFF” position, press and hold program button for 2 seconds, LED will flash rapidly for 2 seconds. Release button, LED will show first MODE with slow flash and second will show option with fast flash. 2-To change MODE, push button one time, LED will confirm MODE with slow number of flash. NOTE: ONLY MODE 8 AND 9 ARE AVAILABLE 3-To change OPTION into selected MODE, press LOCK or UNLOCK with remote of alarm or remote starter. LED will show option with fast flash. 4- To save and exit programming, push and hold button until LED flash one time rapidly, showing end of OPTION programming.
USER MODES ARE IDENTIFIED BY A SLOW LED FLASH PATTERN; FOLLOWED BY A FAST FLASH CONFIRMING OPTION. Example: 8 SLOW FLASH = MODE 8, FOLLOWED BY 1 FAST FLASHES = OPTION 1
MODES AND OPTIONS LIST MODE 8 - RESET OPTION *OPTION 1 = No Reset OPTION 2 = Complete reset of OPTION and module (default) MODE 9 - Optional function programming of Pink, Orange and Orange with Pink wires. You now have 10 seconds to program the desired function, (the LED will turn off if delay is longer) 1. Put wire(s) to be programmed to ground (-) 2. Press on the factory remote button which you want to associate to the wire(s). 3. The LED turns off, the procedure is now successful. 4. Take off wire(s) from ground. The function is now programmed. It is possible to program multiple functions on the same wire(s). EXAMPLE: FOR TRUNK RELEASE: it might be required to unlock doors (disarm factory alarm), trunk release and then relock doors (to rearm factory alarm). To program these three functions on the same wire(s), go to step 1 and then repeat step 2 for each of the desired functions, but not exceeding a 1 second delay between each press of the factory remote button function. The functions will be replayed in the same order as they were learned. *Default value
5
XK01-GMDL6X & XK01-GMDL7X - WIRING DIAGRAM & VEHICLE REFERENCE CHART
XK01-GMDL6X & XK01-GMDL7X Connection of the XK module in Range Extender mode for GM OEM remote starter Internet USB CABLE USB PORT
USB ADAPTOR
IMPORTANT: Latest firmware can be downloaded at www.xpressdownload.com
WIRING DIAGRAM
RED
XTR-LINK-RFTD 1 WAY
BLACK
Programming Button HARNESS #2
1WAY ANTENNA (RX57)
HARNESS #1
LED
OR BLACK
XL201-RFTD 2 WAY
2WAY ANTENNA (TRX72N)
HARNESS #1
LED
10 PIN HARNESS
XK01 GMDL6X OR GMDL7X
D2D
RED
HARNESS #2
Programming Button
N/C
Brown
N/C
N/C
Green
N/C
N/C
Blue
N/C
N/C
Violet/White
N/C
Data
(-)
Violet
Data Output to OBDII
N/C
Pink/White
N/C
N/C
Pink
N/C
Orange
N/C
N/C INPUT
(+)
Red
INPUT
(-)
Black
Data Wire Connects to OBDII PIN 1
1
8
9
16
(+)12 Volt Constant Chassis Ground
Programming Button
XK01-GMDL6X & XK01-GMDL7X VEHICLE PROGRAMMING 1) Once the module has been properly connected, LED comes ON. 2) Turn key to IGNITION position, LED goes OFF. Module is now programmed
6
XK01-GMDL6X & XK01-GMDL7X - OPTION PROGRAMMING USER SETTINGS: OPTION PROGRAMMING 1-Key “OFF” position, press and hold program button for 2 seconds, LED will flash rapidly for 2 seconds. Release button, LED will show first MODE with slow flash and second will show option with fast flash. 2-To change MODE, push button one time, LED will confirm MODE with slow number of flash. ONLY MODE 1 AND 8 ARE AVAILABLE 3-To change OPTION into selected MODE, press LOCK or UNLOCK with remote of alarm or remote starter. LED will show option with fast flash. 4- To save and exit programming, push and hold button until LED flash one time rapidly, showing end of OPTION programming.
USER MODES ARE IDENTIFIED BY A SLOW LED FLASH PATTERN; FOLLOWED BY A FAST FLASH CONFIRMING OPTION. Example: 8 SLOW FLASH = MODE 8, FOLLOWED BY 1 FAST FLASHES = OPTION 1
MODES AND OPTIONS LIST MODE 1 -UNLOCK : *OPTION 1 = 1 pulse unlock all doors OPTION 2 = 1st Pulse: unlock driver door, 2nd Pulse: unlock all doors MODE 8 - RESET OPTION *OPTION 1 = No Reset OPTION 2 = Complete reset of OPTION and module (default)
*Default value
7
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
