Transcript
RGB-DVI 300 and RGB-HDMI 300 (A) Setup Guide RGB-HDMI 300 A ADJUST CONFIG
MENU
ENTER
RGB - HDMI 300 A
Front Panel
POWER 12V 1.0A MAX
INPUT RS-232
RGB/R-Y,Y,B-Y
AUDIO
HDMI OUTPUT
RGB - HDMI 300 A
Tx Rx
Rear Panel
RGB-DVI 300 ADJUST CONFIG
MENU
ENTER
RGB - DVI 300
Front Panel
POWER 12V 1.0A MAX
DVI-D OUTPUT
RGB/ R-Y, Y, B-Y INPUT
RS-232
RGB - DVI 300
Tx Rx
Rear Panel
CAUTION: Installation and service must be performed by authorized personnel only. Unless otherwise stated, these instructions apply to both the RGB-DVI 300 and the RGB‑HDMI 300 (A) video scalers and converters. These instructions provide a quick setup guide for experienced installers.
Step 1 — Power Off Turn all the equipment off and disconnect all cables.
Step 2 — Mounting Mount the unit in a convenient location, in a rack, behind a display, under a desk, or through a desk.
Step 3 — Connect Video and Audio Input Connect an analog RGB or HDTV YUV video input to the 15-pin female VGA connector. Connect an analog audio source to the 3.5 mm TRS connector (RGB-HDMI 300 A only).
Step 4 — Connect Display Device Connect the unit to a digital display using a HDMI connector for the RGB-HDMI 300 (A) or a DVI-I connector for the RGB‑DVI 300.
NOTE: The RGB-DVI 300 only outputs a DVI-D signal, although a DVI-I connector is used for greater installation flexibility.
A display is required to control the RGB-DVI 300 or RGB-HDMI 300 (A) using the menu and on‑screen display.
Step 5 — Connect and Apply Power Connect the 12 VDC external power supply (provided) to the 3.5 mm, two-pole, captive screw Power input connector. Apply power to the RGB-DVI 300 or RGB-HDMI 300 (A) power supply. Then power on the display and power on the video source.
Step 6 — Configure System Configure the system via the front panel controls and on-screen display, Simple Instruction Set™ (SIS™) commands, or the Signal Processing Products Control Program. (See the RGB-DVI 300 and RGB-HDMI 300 (A) User Guide for complete instructions.)
RGB-DVI 300 and RGB-HDMI 300 (A) Setup Guide (Continued) NOTE: If no video output is visible on the display, the output rate of the scaler can be toggled between 1024 x 768 at 60 Hz and 720p at 60 Hz, without needing the on-screen menu. Hold the Menu button while applying power and the output rate is set to 1024 x 768 at 60 Hz during the first power on cycle. Hold the Menu button while applying power a second time and the output rate will toggle to 720p at 60 Hz.
ADJUST
Front Panel Controls Use the Menu and Enter Buttons and two rotary encoders (shown in the figure at right) to open and navigate the menu, which is displayed on the connected output display device. A typical on‑screen menu is shown in the figure at right.
MENU
ENTER
Press the Menu button to display the top level menu. Use the rotary encoders to highlight menu items and the Enter button to select the highlighted item and move deeper into the menu. To move back one level, press the Menu button. For complete information about configuring and controlling the unit through the front panel controls and the on-screen display, see the RGB‑DVI 300 and RGB-HDMI 300 (A) User Guide, which is available online at www.extron.com.
1
SIS Commands and Control Software To control and configure the unit, using SIS commands or the Extron Signal Processing Products Control Program, connect the serial port of a computer to either the RS-232 captive screw connector on the rear panel or the Config port TRS connector on the front panel. Consult the diagrams and table at right to ensure the connections are wired correctly. Note that the Tx and Rx connections must cross over between the computer and the scaler.
5
6
9 Male
DB9 Pinout Pin
TRS
RS-232
Function
2 3 5
Tip Ring Sleeve
TX RX Gnd
Transmit data (-) Receive data (+) Signal ground
For SIS control, the Extron DataViewer software can be downloaded from the Extron Web site at www.extron.com. The control program can also be downloaded from the Extron Web site.
Tip (L) Ring (R)
For further information on controlling and configuring the scaler through SIS commands or control program, see the RGB-DVI 300 and RGB‑HDMI 300 (A) User Guide, which is available online at www.extron.com.
Sleeve ( )
2.5 mm TRS Connector RS-232
Tx Rx
Transmit (Tx) Receive (Rx) Ground (Gnd, )
3 Pin Captive Screw Connector
Extron USA - West
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876 Inside USA/Canada Only
+800.633.9876 Inside USA/Canada Only
+800.3987.6673 Inside Europe Only
+800.7339.8766 Inside Asia Only
+81.3.3511.7655 +81.3.3511.7656 FAX
+400.883.1568 Inside China Only
+971.4.2991800 +971.4.2991880 FAX
+1.714.491.1500 +1.714.491.1517 FAX
+1.919.863.1794 +1.919.863.1797 FAX
+31.33.453.4040 +31.33.453.4050 FAX
+65.6383.4400 +65.6383.4664 FAX
Headquarters
© 2010 Extron Electronics. All Rights Reserved. www.extron.com
+86.21.3760.1568 +86.21.3760.1566 FAX
68-1407-50 Rev B 08 10
