Rm 123/125 Rack Mount Kit Installation Procedure

Transcript

RM 123/125 Rack Mount Kit Installation Procedure This document describes how to install the Model 123 and Model 125 Rack Mount Flange Kits onto the OMM-6810 Optical Multimeter. Once installed the OMM-6810 can be mounted into a standard 19 inch cabinet. If these instructions are unclear, or should you find missing parts, please call ILX Lightwave Customer Support at 406-586-1244. Please locate the following parts shipped with the Rack Mount Kits. Model 125 Single Rack Mounting Kit 1 - Small Rack Mount Flange. (A) 1 - Large Half Rack Width Rack Mount Flange. (B) 4 - 6/32" x 1/4" long Socket Head Screws. 1 - 7/64" Hex Key Wrench. (A) (B) Model 123 Dual Rack Mount Kit for 2 6810's 2 - Small Rack Mount Flanges. (A) 1 - Front Panel Dual Instrument Bracket. (C) 1 - Rear Panel Dual Instrument Strap. (D) 8 - 6/32" x 1/4" long Socket Head Screws. 1 - 7/64" Hex Key Wrench. (C) (D) A Phillips Screwdriver will be required to remove the instrument shell. Before installing the Rack Mount Flanges turn off the power to the OMM-6810 and unplug it from the AC Power Source. WARNING POTENTIALLY LETHAL VOLTAGES EXIST WITHIN THE OMM-6810. TO AVOID ELECTRIC SHOCK, DO NOT PERFORM ANY OF THE PROCEDURES DESCRIBED IN THIS DOCUMENT UNTIL THE OMM-6810 IS UNPLUGGED FROM IT'S AC POWER SOURCE. The following procedures describe how to install the Rack Mount Flanges onto the OMM-6810 Optical Multimeter. Separate procedures describe one instrument and two instrument installation. 700500 12-Rm6810 Rev00 4-20-99 Single Instrument Rack Mount Flange Installation (Model 125) This procedure describes the installation of the Rack Mount Flanges for a single instrument. a. Turn off the power to the OMM-6810 and unplug it from the AC Power Source. 6 -3 2 S C REW S (REA R BEZ EL) REA R BEZ EL CH A S S IS S H ELL 6 -3 2 S O CKET H EA D S CREW S S M A LL RA CK M O U N T FLA N GE (A ) RO U N D W IRE (D O N OT REM OV E) O M M -6 8 1 0 6 -3 2 S CREW (BO T T O M CH A S S IS ) LA RG E RA CK M OU N T FLA N G E (B) Figure 1 - Installing the Single Instrument Rack Mount Flange b. Turn the 6810 so the rear of the device is facing you. Remove the two Phillips screws that hold the rear bezel in place. c. Turn the 6810 over so that it is resting on it’s top. Remove the Phillips screw from the center rear of the shell. Carefully turn the unit right-side-up again. d. Slide the shell about 4 inches toward the rear of the instrument. There is no need to completely remove the shell. e. If you would like to place the instrument on the left side of the rack install the small rack mount flange (A) on the left side of the instrument, otherwise install it (A) on the right side of the instrument. Note the two 6/32" holes in the instrument body about 2 inches from the front panel. f. Secure the small rack mount flange (A) with two 6/32" Hex Screws. The screws are inserted from the inside of the instrument. 700500 12-Rm6810 Rev00 4-20-99 g. Repeat step (f) to install the large half rack width flange (B) on the opposite side of the instrument. h. Slide the shell back onto the instrument. i. Turn the instrument over so it is resting on it's top. Replace the Phillips screw in the center rear of the bottom of the shell. Carefully place the unit right-side-up again. j. Replace the rear bezel and secure it with the two Phillips screws removed in step (b). k. The 6810 is ready for mounting into the cabinet. Dual Instrument Rack Mount Flange Installation (Model 123) This procedure describes the installation of the Rack Mount Flanges for mounting two instruments side-by-side. a. Turn off the power to both OMM-6810s and unplug them from the AC Power Source. b. Follow steps (b) through (d) in Section 1.4.1 to remove the shells from both instruments. c. Install a small rack mount flange (A) on the left side of one of the instruments. Note the two 6/32" holes in the instrument body about 2 inches back from the front panel. Secure the flange with two 6/32" Hex Screws. The screws are inserted from the inside of the instrument. d. Repeat step (c) to install a small rack mount flange (A) on the right side of the other 6810. e. Install the U-shaped Dual Instrument Bracket (C) between the two instruments. Secure the bracket with four 6/32" Hex Screws. The screws are inserted from the inside of the instrument. f. Follow steps (h) through (j) in Section 1.4.1 to replace the instrument shells. For now, replace only the outside Phillips screws on the rear bezels. g. Install the Rear Panel Dual Instrument Strap (D) across the rear panel of both 6810s. Secure it and the rear bezel with the inside Phillips screws. h. The 6810s are ready for mounting into the cabinet. 700500 12-Rm6810 Rev00 4-20-99