Transcript
RMC12015 Anderic® Master Instructions
www.ReplacementRemotes.com
RMC12015 Setup Guide This is the Anderic® Replacement Master remote Setup guide for Philips and Magnavox Commercial Televisions.
1
Activating Master TV Setup Menu The Anderic RR2573 is the Master remote for your Philips and Magnavox commercial televisions. These simple instructions will help you convert your TV from “Commercial Mode” to “Consumer Mode” for full access to the menus.
Check to see if your TV is in Commercial Mode or Consumer Mode. 1. Press “RC5” MODE button at bottom of remote. To put remote in correct mode. 2. Press “RECALL” button on the remote. The TV Status menu will appear (shown below). 3. Look at line #11 of the onscreen menu to see if the TV is in Commercial or consumer mode.
Note: If Line #11 says “COMMERCIAL” mode then you must change this mode to “Consumer Mode” in order to grant access to the full setup menu. Please use the following steps to change it.
Changing from Commercial Mode to Consumer Mode: 1. Press “RC5” MODE button at bottom of remote. To put remote in SETUP mode. 2. Press “Menu” button on remote. This will activate the TV Setup Menu.
3. Press number keys “024995” (or “319753”) followed by the “Menu” button on the remote. The TV Setup Menu will appear.
Note: the following steps may vary depending on model of TV. 4. Using the directional pad on the remote, Highlight “commercial mode,” and Press “LEFT ARROW” or “RIGHT ARROW” to select “Consumer Mode.” 5. To exit, press “DOWN ARROW” followed by “RIGHT ARROW” to store your setting. 6. Highlight STORE and press the “RIGHT ARROW” button on remote to store the change. The TV will turn off. You are now in Consumer Mode and should have full access to your menu options. For a full operating manual for your TV go to www.ReplacementRemotes.com.
46 3%450 -!). -%.5
"# #! " ""$ "$!"# " !! " !" ! !! " " ! #" ! # ! $ " !! # #"& ! #" !" #" !! $ # $ # &$ # !%" $ # !%" % ! ' ' ! # $ #" # $ #" #" " #" % !! # " " ' $!%" ,(+-) *)*.(+ !$ ! # #" $ #"
'! '! '! ------------- ------------- ------------- ------------- ------------- '! !" '! '! ///////////// ///////////// ///////////// '! '! ! " '$ "# '! '! ///////////// ///////////// !" ///////////// !" "$
$ !!$ $ !" !" # '! # '! '! '! % '! '! '! #" #" '! '! '!
!$$ $ !"# ! " !# "'
'! !"
) % $ #' #! )$ $ #" $" %$ %!"## " $#$$$"#!$ & % $ ##$$ ## $ " $ )$#$$ $# $ % $ !"## " ( $!"##
" $ #$%!" $ $"
' #$' #"* #" ,$$%* "' (''#" &$%&& " ' "" & ' #" "' "" &" # ' #$' #"* "#')
*
46 3%450 -%.5 35" -%.53
,!.'5!'% %.',)3( %30!./, &2!.#!)3 7HEN YOU FIRST ENTER THE 46 3%450 -ENU ,!.'5!'% IS HIGHLIGHTED 3CROLL TO THE ,!.'5!'% ITEM SELECT OTHER LANGUAGES WITH THE q OR BUTTON ON THE REMOTE CONTROL
#(!..%, ).34!,, 7HEN SELECTED #(!..%, ).34!,, MENU APPEARS #ONFIGURE THE INPUTS AND CHANNELS AS SEEN HERE
).054
3ELECT THE CHANNEL OR INPUT YOU WISH TO CONFIGURE 3ELECT THE CHANNEL OR INPUT YOU WISH TO ASSOCIATE WITH THE SPECIFIC #(!..%, 4HIS FEATURE ENABLES YOU TO MAP RE ASSIGN A NUMERIC CHANNEL NUMBER TO A VIDEO INPUT RATHER THAN TO ITS NORMAL 2& 46 CHANNEL IE !.4%..! CHANNEL
!+,( " &&!$&*+ $$ '%%!) # $' !
.OTE !LTHOUGH IT IS POSSIBLE TO MAP A GIVEN VIDEO SOURCE EG #6) TO ANOTHER VIDEO SOURCE EG 3 6)$%/ THIS IS NOT ADVISIBLE AS IT MAY LEAD TO CONFUSION
!54/ 02/'2!-
7HEN !54/ 02/'2!- IS SELECTED THE 46 PERFORMS AN AUTOMATIC SEARCH FOR THE PRESENCE OF VIABLE 2& SIGNALS AT ITS TUNER INPUT !N !54/ 02/'2!--).' !#4)6% 4!",% OF ACTIVE NUMBERS WILL APPEAR 7HEN A VIABLE SIGNAL IS DETECTED ON A GIVEN CHANNEL THAT CHANNEL IS HIGHLIGHTED IN RED AND IS ADDED TO THE CHANNEL RING )F #!",% 45.).' IS SET TO ./ CHANNELS THROUGH WILL BE CHECKED 7HEN A VIABLE SIGNAL IS DETECTED ON A GIVEN CHANNEL THAT CHANNEL IS HIGHLIGHTED IN RED AND IS ADDED TO THE CHANNEL RING 0RESSING ANY KEY ON THE REMOTE CONTROL WILL TERMINATE THE !54/ 02/'2!- SESSION
#(!..%, 2).' 3PECIFY WHETHER THE CURRENT CHANNEL OR INPUT IS TO BE 3!6%$ OR 3+)00%$ FROM THE CHANNEL RING IE LIST OF CHANNELS AVAILABLE FOR SELECTION WITH A GUEST REMOTE CONTROL
,!"%, )NPUT A MAXIMUM NUMBER OF CHARACTERS FOR THE CHANNELS LABEL 0RESS CURSOR q TO START THE FIRST CHARACTER #URSOR q OR TO NAVIGATE BETWEEN CHARACTER POSITIONS WITHIN THE LABEL FIELD #URSOR OR a TO SELECT CHARACTERS FROM THE LIST ! : OR ETC 4O EXIT PRESS CURSOR q OR TO NAVIGATE OUT OF THE LABEL EDITING FIELD
6)$%/ ",!.+ )F 6)$%/ ",!.+ IS SET TO ./ 6IDEO WILL BE DISPLAYED )F 6)$%/ ",!.+ IS SET TO 9%3 6IDEO WILL NOT BE DISPLAYED
!5$)/ -54% )F !5$)/ -54% IS SET TO ./ 4HE CURRENT CHANNEL IS AUDIBLE )F !5$)/ -54% IS SET TO 9%3 4HE CURRENT CHANNEL IS MUTED
#!",% 45.).' ./ 9%3 )F #!",% 45.).' IS SET TO ./ 9OU ARE SELECTING STANDARD OFF AIR TUNING )F #!",% 45.).' IS SET TO 9%3 9OU ARE SELECTING CABLE OFFSET TUNING
46 3%450 -%.5 35" -%.53 #/.4).5%$ 53% #(!..%, 4!",% ./ 9%3 )F 53% #(!..%, 4!",% IS SET TO ./ 4HE DIGITAL TUNER WILL IGNORE THE 6IRTUAL #HANNEL 4ABLE 6#4 INFORMATION THAT IS CONTAINED IN THE 0ROGRAM AND 3YSTEM )NFORMATION 0ROTOCOL 03)0 DURING CHANNEL INSTALLATION OR $IRECT #HANNEL #OMMAND WHICH IS SENT BY THE 46 SET 7HEN 6#4 IS IGNORED THE DIGITAL TUNER WILL TUNE TO THE PHYSICAL CHANNEL 2ADIO &REQUENCY 2& #HANNEL 0ROGRAM -AP 4ABLE 0-4 WHICH IS STORED AS CHANNEL NUMBER -AJOR DOT -INOR EG IN THE 46 SET 4HE VIRTUAL CHANNELS WILL NOT BE USED IN THIS CASE )F 53% #(!..%, 4!",% IS SET TO 9%3 0ROGRAM AND 3YSTEM )NFORMATION 0ROTOCOL 03)0 IS USED DURING CHANNEL INSTALLATION AND $IRECT #HANNEL #OMMAND 4HE DIGITAL TUNER WILL USE THE VIRTUAL CHANNEL INFORMATION THAT IS CONTAINED IN THE 03)0 TO MAP THE VIRTUAL CHANNELS TO THE PHYSICAL CHANNELS WHICH IS ALSO CALLED -AJOR DOT -INOR CHANNEL IN THIS CASE &OR MORE INFORMATION ON THE 03)0 YOU CAN REFER TO !43# 3TANDARD 0ROGRAM AND 3YSTEM INFORMATION 0ROTOCOL FOR 4ERRESTRIAL "ROADCAST AND #ABLE 2EVISION " WHICH CAN BE FOUND AT THE WEBSITE HTTPWWWATSCORGSTANDARDSA?BPDF $)')4!, 46 ,!"%, ./ 9%3 )F $)')4!, 46 ,!"%, IS SET TO ./ 4HE $IGITAL 46 CHANNEL NUMBER WILL NOT BE DISPLAYED ON THE SCREEN )F $)')4!, 46 ,!"%, IS SET TO 9%3 4HE $IGITAL 46 CHANNEL NUMBER WILL BE DISPLAYED ON THE TOP RIGHT HAND CORNER OF THE 46 SCREEN FOR ABOUT SECONDS WHENEVER THERE IS A CHANGE IN DIGITAL 46 CHANNEL &OR THE CHANGES IN THE $IGITAL 46 LABEL TO TAKE EFFECT PLEASE CONDUCT A COLD WARM START WHEN THE SETTING IS CHANGED FROM 9ES TO .O VICE VERSA
$46 3%450 %NTERING THE $46 3%450 MENU ALLOWS YOU TO EDIT FEATURES WHILE YOU ARE IN $IGITAL 46 MODE
#(!..%, %$)4 #HANNEL EDIT ALLOWS YOU TO ADD OR SKIP CHANNELS FROM YOUR FAVORITE LIST
0RESS #523/2 OR TO TOGGLE BETWEEN !DDED OR 3KIPPED )F 3KIPPED IS SELECTED THE CHANNELS WILL BE SKIPPED WHEN SCROLLING CHANNELS WITH THE #( OR #( )F !DDED IS SELECTED THE CHANNELS WILL NOT BE SKIPPED WHEN SCROLLING CHANNELS WITH THE #( OR #(
.OTE 7HEN YOU ARE IN $IGITAL -ODE YOU CAN ONLY ADD OR SKIP PROGRAMS IN $IGITAL #HANNELS
7EAK $IG 3IG $IGITAL BROADCASTING IS STILL NEW 4HEREFORE IT IS NOT UNCOMMON FOR A BROADCASTER TO ONLY SEND OUT A DIGITAL SIGNAL FOR PART OF A DAY 4HE RECEPTION COULD ALSO COME AND GO )F YOU PROGRAM YOUR CHANNELS WHEN THE SIGNAL IS NOT BEING SENT OR IS WEAK IT WILL NOT BE SAVED IN YOUR CHANNEL SETUP 5SING THE 7EAK $IGITAL 3IGNAL FEATURE HERE YOU CAN ADD THOSE CHANNELS WITH WEAK OR NO SIGNALS TO YOUR CHANNEL LIST !DDING OR SKIPPING 7EAK $IGITAL 3IGNAL CAN /.,9 BE DONE IN $IGITAL -ODE
!UTO,OCK NOT SUPPORTED &ACT #H 2ESET &ACTORY #HANNEL 2ESET FEATURE LETS YOU ERASE THE CONTENTS OF THE MASTER USER AND FAVORITE CHANNEL LISTS 4HIS RESTORES THE 46 TO THE INITIAL STATE BEFORE THE FIRST !UTO 0ROGRAM OPERATION &OR INSTRUCTIONS ON HOW TO !UTO )NSTALL THE 46 AGAIN REFER TO PAGE
$IGITAL !UDIO !UD $IGITAL !UDIO ALLOWS YOU TO SWITCH TO ANOTHER AUDIO LANGUAGE WHEN IT IS AVAILABLE
4IMER NOT SUPPORTED #LOSED #APTION #LOSED #APTION LETS YOU SELECT THE DEFAULT OPTION OR OPTIONS THAT YOU HAVE ASSIGNED TO YOUR #LOSE CAPTIONING SERVICE 4HIS FEATURE IS /.,9 AVAILABLE IN $IGITAL -ODE
%MERGENCY ERGENCY !LERT %MERGENCY MERGENCY !LERT LETS YOU DISPLAY OR DISCARD EMERGENCY ALERTS FOR ,OW OR -EDIUM PRIORITY .OTE %MERGENCY !LERT WILL NOT BE VISIBLE IF NO BROADCAST IS RECEIVED OR WHEN THE 46 IS IN 3TANDBY MODE
46 3%450 -%.5 35" -%.53 #/.4).5%$
"2)'(4.%33 #/,/2 #/.42!34 3(!20.%33 4).4 \\\\\\\\\ 4).4 \\\\\\\\ !DJUST THE RESPECTIVE PICTURE SETTING USING THE q OR CURSOR
./)3% 2%$5#4)/. ./ 9%3 )F ./)3% 2%$5#4)/. IS SET TO ./ 4HE NOISE REDUCTION FEATURE IS DISABLED )F ./)3% 2%$5#4)/. IS SET TO 9%3 6IDEO NOISE IS REDUCED WITH MINIMUM REDUCTION IN PICTURE SHARPNESS
3/5.$ -/$% -/./ 34%2%/ 34%2%/ 3ELECT EITHER 34%2%/ OR -/./ SOUND MODES 7HEN 3/5.$ -/$% IS CHANGED AN ON SCREEN DISPLAY WILL APPEAR INDICATING THE ACTUAL AUDIO STATUS -/./ OR 34%2%/ .OTE )F 3TEREO IS NOT AVAILABLE ON A SELECTED SHOW THE SOUND COMING FROM THE 46 WILL REMAIN IN THE -ONO MODE EVEN IF THE 46 IS SET TO 3TEREO MODE
!6, !UTO 6OLUME ,EVELER ./ 9%3 7HEN TURNED TO 9%3 !6, WILL LEVEL OUT THE SOUND BEING HEARD WHEN SUDDEN CHANGE IN VOLUME OCCURS DURING COMMERCIAL BREAKS OR CHANNEL CHANGES
3!0 ./ 9%3 $ISABLE OR ENABLE THE 3ECOND !UDIO 0ROGRAM CHANNEL FEATURES 3!0 IS NOT WIDELY USED AND MOST CHANNELS DO NOT TRANSMIT A 3!0 SIGNAL 5SE OF THE 3!0 CHANNEL INCLUDE
3PANISH TRANSLATION OR OTHER LANGUAGE TRANSLATION
$ESCRIPTIVE INFORMATION ABOUT THE PROGRAM
$UPLICATION OF MAIN AUDIO MONO
!UDIO UNRELATED TO PROGRAM .OTE 7HEN 3!0 IS SET TO 9%3 BUT 3!0 IS NOT PRESENT ON THE CURRENT CHANNEL THE PRIMARY AUDIO WILL BE AUDIBLE
"!,!.#% 42%",% "!33 \\\\\\\\\ "!,!.#% \\\\\\\\ "ALANCE ,EVEL OF SOUND COMING FROM THE LEFT AND RIGHT SPEAKERS 4REBLE
%NHANCE THE HIGH FREQUENCY SOUNDS
"ASS
%NHANCE THE LOW FREQUENCY SOUNDS
.OTE !DJUST THE RESPECTIVE AUDIO PLAYBACK SETTING USING THE q OR CURSOR !5$)/ /54 &)8%$ ./ 9%3 )F !5$)/ /54 &)8%$ IS SET TO 9%3 -/.)4/2 /54 AUDIO LEVEL IS SET TO A FIXED NOMINAL ONE VOLT PEAK TO PEAK VOLTS 2-3 AT OHM IRRESPECTIVE OF THE 46S VOLUME SETTING )F !5$)/ /54 &)8%$ IS SET TO ./ 4HE -/.)4/2 /54 AUDIO LEVEL WILL VARY WITH THE 46S VOLUME SETTING 30%!+%2 -54% ./ 9%3 )F 30%!+%2 -54% IS SET TO ./ 4HE 46S BUILT IN SPEAKERS WILL OPERATE AS THEY WOULD NORMALLY )F 30%!+%2 -54% IS SET TO 9%3 4HE 46S BUILT IN SPEAKERS WILL BE SET TO MUTE
).#2%$)",% 34%2%/ ./ 30!4)!, $/,"9 6)245!, )F ).#2%$)",% 34%2%/ IS SET TO ./ THERE WILL NOT BE ANY SPECIAL AUDIO EFFECTS APPLIED TO THE 46 SOUND )F ).#2%$)",% 34%2%/ IS SET TO 30!4)!, THE SOUND FROM THE 46 WILL BE SPECIALLY PROCESSED WITH AUDIO SPATIALIZER ALGORITHMS RESULTING IN A $ STEREO LIKE EFFECT )F ).#2%$)",% 34%2%/ IS SET TO $/,"9 6)245!, THE SOUND FROM THE 46 WILL BE SPECIALLY PROCESSED WITH PATENTED $OLBY AUDIO ALGORITHMS RESULTING IN A $ STEREO SURROUND EFFECT THAT CONFORMS TO THE ACOUSTIC PERFORMANCE LEVEL AS SPECIFIED BY $OLBY
5,42! "!33 ./ 9%3 7HEN 5,42! "!33 IS SET TO 9%3 THE AUDIO FREQUENCY EQUALIZATION IS MODIFIED SUCH THAT THE BASS FREQUENCIES ARE SIGNIFICANTLY EMPHASIZED
6/,5-% "!2 ./ 9%3 7HEN 6/,5-% "!2 IS SET TO 9%3 AN /3$ GRAPHIC APPEARS PROVIDING VISUAL VERIFICATION EG \\\\\\\\
OF VOLUME ADJUSTMENTS MADE WITH THE REMOTE CONTROL OR THE FRONT PANEL OF THE 46
46 3%450 -%.5 35" -%.53 #/.4).5%$ -). 6/,5-% \\\\\\\\\\\\\ 3PECIFY THE LOWEST VOLUME SETTING POSSIBLE BY USING THE REMOTE CONTROL OR THE 46 FRONT PANEL IF IT IS NOT LOCKED OUT 4HIS SETTING CANNOT EXCEED THE -!8 6/,5-% -!8 6/,5-% \\\\\\\\\\\\\ 3PECIFY THE HIGHEST VOLUME SETTING POSSIBLE BY USING THE REMOTE CONTROL OR THE 46 FRONT PANEL IF IT IS NOT LOCKED OUT 4HIS SETTING CANNOT BE LESS THAN THE -). 6/,5-% 37)4#( /. 6/,5-% 34!.$!2$ \\\\\\\\\\\\\ 3PECIFY THE VOLUME SETTING THAT TAKES EFFECT WHEN THE 46 IS POWERED ON )F 34!.$!2$ THE VOLUME AT POWER ON WILL BE THE VOLUME AT WHICH THE 46 WAS PRIOR TO LAST POWER DOWN )F SPECIFIED AS THAT WILL ALWAYS BE THE VOLUME AT POWER ON UNTIL 37)4#( /. 6/,5-% IS CHANGED 37)4#( /. #(!..%, 34!.$!2$ 46 !6 3)$% 3 6)$%/ #6) 3PECIFY THE CHANNEL WHICH THE 46 WILL BE TUNED WHEN IT IS POWERED ON )F 34!.$!2$ THE CHANNEL AT POWER ON WILL BE THE SAME AS THE CHANNEL WHEN THE 46 WAS TUNED AT LAST POWER DOWN )F SPECIFIED EG !6 #6) ETC THEN THAT WILL BE THE CHANNEL AT POWER ON UNTIL 37)4#( /. #(!..%, IS CHANGED 0/7%2 /. 34!.$!2$ &/2#%$ 2%34/2%$ 34!.$!2$ 4HE 46 WILL BE IN STANDBY MODE WHEN !# MAINS POWER IS FIRST APPLIED AFTER BEING DISCONNECTED &/2#%$ 4HE 46 WILL TURN /. WHENEVER !# MAINS POWER IS APPLIED 4HIS FEATURE ALLOWS THE 46S POWER STATUS TO BE CONTROLLED FOR EXAMPLE FROM AN !# MAINS BREAKER 2%34/2%$ 7HEN !# MAINS POWER IS FIRST APPLIED AFTER BEING DISCONNECTED THE 46S POWER STATUS WILL REVERT TO THAT WHEN THE !# MAINS POWER WAS LAST REMOVED #(!..%, $)30,!9 ./.% .5-"%2 ,!"%, !,, 3PECIFIES WHICH OF THE RESPECTIVE CHANNEL PROPERTIES ARE DISPLAYED BY THE 46S /3$ WHEN A CHANNEL OR INPUT IS FIRST SELECTED )F 2%-).$%2 SEE 2%-).$%2 PAGE IS /&& THESE PROPERTIES WILL BE DISPLAYED FOR A FEW SECONDS THEN DISAPPEAR )F 2%-).$%2 IS /. THE CHANNEL PROPERTIES REMAIN ON SCREEN AS LONG AS THE 46 IS ON +%9"/!2$ ,/#+ ./ 9%3 ./ 4HE 46S FRONT PANEL IS ENABLED 9%3 4HE 46S FRONT PANEL IS DISABLED %30 %.%2'9 3!6).' 02/'2!--!"),)49 /&& (2 (2 (2 4HIS FEATURE ENABLES THE 46 TO AUTOMATICALLY POWER DOWN AFTER A SPECIFIED PERIOD OF TIME )F DURING THIS PERIOD IT DOES NOT RECEIVE ANY COMMANDS FROM THE REMOTE CONTROL OR 46 FRONT PANEL THIS ENERGY SAVING FEATURE ASSUMES THE 46 IS INACTIVE AND WILL AUTOMATICALLY POWER DOWN !5$)/ 6)$%/ -54% /&& ",!#+ ",5% !LSO KNOWN AS !6 MUTING 3UPPRESSES AUDIO AND VIDEO WHEN THE 46 TUNER IS NOT RECEIVING SUFFICIENT 2& SIGNAL 4HESE OPTIONS PRODUCE THE FOLLOWING RESULTS /&& 46 SCREEN DISPLAYS SNOW AND THE AUDIO APPEARS AS WHITE NOISE STATIC ",!#+ 46 SCREEN DISPLAY IS BLACK AND THE AUDIO IS MUTED ",5% 46 SCREEN DISPLAY IS BLUE AND THE AUDIO IS MUTED !5$)/ 6)$%/ /54 -54% ./ 9%3 7HEN SET TO 9%3 IT TURNS OFF THE AUDIO AND VIDEO -/.)4/2 /54 SIGNALS EITHER DEMODULATED 2& INPUT OR LOOP THROUGH VIDEO )NTENDED TO PREVENT RECORDING OF PAY PER VIEW CONTENT -/.)4/2 /54 2& ./ 9%3 4HIS FEATURE CONFIGURES THE AUDIO AND VIDEO MONITOR OUTPUTS PROVIDED THE !5$)/ 6)$%/ /54 -54% IS NOT SET TO 9%3 ./ 4HE SIGNALS THAT ARE PRESENT AT THE MONITOR OUTPUTS ARE THE SAME AS THOSE OF THE CURRENTLY SELECTED CHANNELS OR VIDEO INPUT 4HE MONITOR OUTPUTS TRACK WHAT IS VIEWED AND HEARD ON THE 46 9%3 2EGARDLESS OF THE CURRENT SELECTED 46 SOURCE EG !6 3 6)$%/ #6) INPUT THE SIGNAL PRESENT AT THE MONITOR OUTPUTS IS ALWAYS THE TUNER OUTPUT SEE ./4% BELOW
.OTE 7HEN 4HE -/.)4/2 /54 2& IS INITIALLY CHANGED FROM ITS CURRENT SETTING THE MONITOR OUT SIGNAL DEPENDS UPON THE PREVIOUS -/.)4/2 /54 SETTING UNTIL A DIFFERENT 46 SOURCE IS SELECTED &ROM THEN ON THE NEW -/.)4/2 /54 SETTING WILL PERFORM AS DESCRIBED
46 3%450 -%.5 35" -%.53 #/.4).5%$ 7%,#/-% -%33!'% ! WELCOME MESSAGE MAXIMUM OF CHARACTERS LINES CAN BE PROGRAMMED TO APPEAR ON THE 46 SCREEN WHEN THE 46 IS POWERED ON 4HE MESSAGE REMAINS ON THE SCREEN UNTIL ANY BUTTON ON THE 46 FRONT PANEL OR REMOTE CONTROL IS PRESSED 4HIS IS HOW TO SET THE 7ELCOME -ESSAGE 7HEN THE 7%,#/-% -%33!'% SETUP MENU IS HIGHLIGHTED 0RESS CURSOR q OR ON THE REMOTE CONTROL TO INVOKE THE 7%,#/-% -%33!'% SUB MENU
.OTE
0RESS CURSOR OR a ON THE REMOTE CONTROL TO SELECT THE DESIRED -%33!'% SUB MENU ITEM EG ,).% ,).% 7HEN $)30,!9 IS HIGHLIGHTED PRESS CURSOR q OR ON THE REMOTE CONTROL TO SELECT 9%3 OR ./ 7HEN 9%3 IS SELECTED 7%,#/-% -%33!'% IS ENABLED #HOOSE ./ TO DISABLE 7%,#/-% -%33!'% .OTE )F 7ELCOME -ESSAGE IS ENABLED BUT BOTH ,).% AND ,).% ARE BLANK OR CONSIST ENTIRELY OF SPACE CHARACTERS NO MESSAGE WILL APPEAR 3ELECT MESSAGE ,).% OR ,).% 0RESS CURSOR q ON THE REMOTE CONTROL TO START THE FIRST CHARACTER ! BLINKING WILL APPEAR INDICATING THAT YOU ARE IN THE EDIT MODE 0RESS CURSOR OR a TO SELECT A CHARACTER AT THE GIVEN POSITION 4O MOVE TO A DESIRED CHARACTER POSITION PRESS q OR 7HEN YOU CURSOR TO THE LEFT OR RIGHT MARGINS OF THE EDIT SPACE THE BLINKING WILL DISAPPEAR AND WILL RE APPEAR AT THE END OF THE MENU LINE 9OU CAN THEN CURSOR OR a TO THE NEXT OR PREVIOUS LINE IN THE -%33!'% SUB MENU 3ELECT #,%!2 TO ERASE THE ENTIRE MESSAGE
#(!..%, '5)$% ./ 9%3 0/7%2 /. 4HE CHANNEL GUIDE FEATURE PROVIDES AN ON SCREEN SUMMARY LISTING OF THE 2& TUNER CHANNELS THAT ARE CURRENTLY IN THE CHANNEL RING SEE #(!..%, ).34!,, #(!..%, 2).' AND HAVE BEEN ASSIGNED LABELS SEE #(!..%, ).34!,, ,!"%, #HANNEL 'UIDE IS NOT DISPLAYED WHEN #( '5)$% ON THE REMOTE CONTROL IS PRESSED AND ./4 !6!),!",% MESSAGE APPEARS ON THE 46 SCREEN 9%3 7HEN #( '5)$% BUTTON ON THE REMOTE CONTROL IS PRESSED THE CHANNEL GUIDE IS DISPLAYED FOR APPROXIMATELY SECONDS OR UNTIL A COMMAND IS RECEIVED FROM THE REMOTE CONTROL AGAIN !LL 2& TUNER CHANNELS THAT ARE IN THE SAME CHANNEL RING AND HAVE LABELS WILL APPEAR IN THE CHANNEL LIST 0/7%2 /. 4HE CHANNEL GUIDE APPEARS AUTOMATICALLY AT POWER ON AND REMAINS ON SCREEN FOR APPROXIMATELY SECONDS OR UNTIL A REMOTE CONTROL COMMAND OCCURS 4HE CHANNEL GUIDE ALSO APPEARS WHEN #( '5)$% BUTTON ON THE REMOTE CONTROL IS PRESSED .OTE 4O APPEAR IN THE CHANNEL GUIDE AN 2& TUNER CHANNEL MUST BE ASSIGNED A LABEL AND MUST BE SAVED IN THE CHANNEL RING .OTE /NLY 2& TUNER CHANNELS WILL BE LISTED IN THE CHANNEL GUIDE 6IDEO INPUTS EG !6 3 6)$%/ #6) &2/.4 !6 WILL NOT APPEAR ./
$)30,!9
./ 9%3
,).%
0(),)03
#,%!2
46 3%450 -%.5 35" -%.53 #/.4).5%$ 2%-).$%2 ./ 9%3 7HEN 2%-).$%2 IS SET TO 9%3 THE CURRENT CHANNEL OR INPUT LABEL WILL BE DISPLAYED AT THE TOP OF THE 46 SCREEN EG 46 #6) ETC 4HE CHANNEL NUMBER OR INPUT LABEL IF A LABEL HAS BEEN ASSIGNED IN #(!..%, ).34!,, AND THE CURRENT -54% STATUS IE IF SOUND IS -54%$ WILL ALSO BE DISPLAYED WHEN AVAILABLE 7HEN 2%-).$%2 IS SET TO ./ THE REMINDER INFORMATION WILL APPEAR ONLY WHEN THE CHANNEL OR INPUT LABEL IS CHANGED 4HIS REMINDER INFORMATION WILL DISAPPEAR AFTER TEN SECONDS $)')4 %.429 ./ 9%3 9%3 5PON RECEIVING A SIGNAL FROM THE REMOTE CONTROL THE 46 EXPECTS TO RECEIVE UP TO TWO MORE SUCCESSIVE REMOTE DIGIT COMMANDS EG ETC BEFORE TUNING TO THE INTENDED CHANNEL !S THE 46 RECEIVES THE SIGNAL FROM THE REMOTE CONTROL EACH DIGIT WILL BE DISPLAYED ON THE TOP LEFT HAND CORNER OF THE 46 SCREEN 4HIS DIGIT WILL BE FOLLOWED BY A INDICATING THAT THE 46 IS WAITING FOR THE DIGIT INPUT SEE .OTE ./ 5PON RECEIVING A SIGNAL FROM THE REMOTE CONTROL THE 46 EXPECTS TO RECEIVE ONE MORE SUCCESSIVE REMOTE CONTROL DIGIT CONMAND BEFORE TUNING TO THE INTENDED CHANNEL SEE .OTE .OTE 3UCCESSIVE DIGIT COMMANDS MUST OCCUR WITHIN TWO SECONDS OR THE 46 WILL INTERPRET THE RECEIVED DIGITS AS THE INTENDED CHANNEL AND TUNE TO IT ACCORDINGLY !#( !6 37)4#( ./ 9%3 4HE !#( !6 ALTERNATE CHANNEL !6 SWITCH FEATURE PROVIDES THE CHOICE TO USE THE REMOTE CONTROL !#( COMMAND TO TOGGLE BETWEEN THE PREVIOUSLY VIEWED CHANNELS INPUTS TO STEP SUCCESSIVELY THROUGH ALL SOURCES EG !.4%..! TUNER !6 3 6)$%/ #6) &2/.4 PRESENTLY IN THE CHANNEL RING 9%3 5PON RECEIVING AN ALTERNATE CHANNEL !#( COMMAND FROM THE REMOTE CONTROL THE 46 WILL TUNE TO THE NEXT SIGNAL SOURCE EG TUNER !6 3 6)$%/ ETC IN THE CHANNEL RING ./ 5PON RECEIVING AN ALTERNATE CHANNEL !#( COMMAND FROM THE REMOTE CONTROL THE 46 WILL SWITCH TO THE MOST RECENTLY SELECTED CHANNEL INPUT #3 #3 #3 #3 #3 3 #3 ## ## ## ## /&& -54% FOR FOR DIGITAL CHANNELS CHANNELS
## ## /&& ## /. -54% FOR ANALOG CHANNELS 3INCE *ULY 46 SETS WITH SCREENS OR LARGER MUST HAVE BUILT IN CAPTION DECODERS #APTIONING OF MOST BROADCAST AND CABLECAST PROGRAMMING IS MANDATED UNDER THE 4ELECOMMUNICATIONS !CT OF EXCEPT FOR PROGRAMS EXEMPTED BY THE &## &OR ADDITIONAL INFORMATION PLEASE VISIT THE 53 &## WEBSITE AT HTTPWWWFCCGOVCGBCONSUMERFACTSCLOSEDCAPTIONHTML /&& #LOSE CAPTIONING TEXT WILL NOT BE DISPLAYED EVEN WHEN IT IS PROVIDED BY THE BROADCASTER -54% OR ## /. -54% #LOSE CAPTIONING TEXT WILL APPEAR ONLY WHEN THE 46 IS -54%$ #3 #3 #3 #3 #3 #3 ## ## ## ## ## ## #LOSE CAPTIONING TEXT WILL BE DISPLAYED IF IT IS PRESENT IN THE INCOMING SIGNAL 3!6% ## ./ 9%3 4HIS FEATURE ENABLES THE ## SETTING SEE ## TO REMAIN IN EFFECT AFTER THE 46 IS POWERED DOWN ./ 7HEN THE 46 IS POWERED DOWN AND TURNED ON AGAIN THE CLOSED CAPTIONING SETTINGS WILL DEFAULT TO /&& 9%3 7HEN THE 46 IS POWERED DOWN AND TURNED ON AGAIN THE CLOSED CAPTIONING PREVIOUSLY SET WILL REMAIN IN EFFECT 3/52#% -%.5 )4%- ./ 9%3 4HIS FEATURE PROVIDES THE OPTION TO SPECIFY WHETHER THE CURRENT SIGNAL SOURCE EG 46 !6 #6) 3 6)$%/ ETC ITEM IS PRESENT IN THE &%!452%3 -%.5 THAT APPEARS WHEN THE 3,%%0 OR ## BUTTON ON THE REMOTE CONTROL IS PRESSED OR WHEN THE -%.5 OR 2%#!,, BUTTON ON THE GUEST MODE REMOTE CONTROL IS PRESSED ./ 4HE 3/52#% LINE ITEM DOES NOT APPEAR IN THE &%!452%3 -%.5 9%3 4HE 3/52#% LINE ITEM APPEARS IN THE &%!452%3 -%.5
!"
!"
!"
$%" # %& $ % $
46 3%450 -%.5 35" -%.53 #/.4).5%$ .OTE .OTE .OTE
7HEN THE 3/52#% ITEM IS HIGHLIGHTED PRESS q OR ON THE REMOTE CONTROL TO STEP THROUGH THE SIGNAL SOURCES EG TUNER !6 3 6)$%/ ETC THAT ARE IN THE #(!..%, 2).' 4HE 3/52#% ITEM IN THE &%!452%3 -%.5 CANNOT BE USED TO SELECT 2& TUNER CHANNELS 4HE 3/52#% ITEM CAN ONLY BE USED TO SELECT SIGNAL SOURCES EG TUNER !6 3 6)$%/ ETC THAT ARE IN THE #(!..%, 2).' )F THERE ARE NO SIGNAL SOURCES IN THE #(!..%, 2).' OTHER THAN THE PRESENTLY SELECTED SOURCE THE 3/52#% ITEM IS FOR DISPLAY PURPOSE ONLY YOU CANNOT SELECT ANY OTHER SOURCE
6 #()0 -%.5 )4%- ./ 9%3 4HIS FEATURE PROVIDES THE OPTION TO SPECIFY WHETHER THE 6 #()0 WILL APPEAR IN THE &%!452%3 -%.5 ./ 4HE 6 #()0 LINE ITEM DOES NOT APPEAR IN THE &%!452%3 -%.5 9%3 4HE 6 #()0 LINE ITEM APPEARS IN THE &%!452%3 -%.5
!"
!"
!"
$%" # %& $
% $ 4HE &%!452%3 -%.5 CAN BE ACTIVATED BY PRESSING THE 3,%%0 OR -%.5 BUTTON ON THE GUEST REMOTE CONTROL
.OTE
3!6%$ 6 #()0 ./ 9%3 4HIS FEATURE PROVIDES THE OPTION TO SPECIFY WHETHER THE 6 #()0 3%450 CONFIGURATION REMAINS IN EFFECT AFTER THE 46 IS POWERED DOWN ./ 4HE CURRENT 6 #()0 SETUP CONFIGURATION REVERTS TO DEFAULTS DOES NOT APPEAR ON THE &%!452%3 -%.5 WHEN THE 46 IS POWERED DOWN 9%3 4HE CURRENT 6 #()0 SETUP CONFIGURATION REMAINS IN EFFECT WHEN THE 46 IS POWERED DOWN
6 #()0 3%450 ./ 9%3 #ONFIGURES THE 6 #()0 PROGRAM CONTENT VIEWING RESTRICTION FEATURE 0LEASE CONSULT THE MAINSTREAM CONSUMER PRODUCT DOCUMENTATION FOR DETAILS ABOUT THIS FEATURE -!34%2 $)3!",% ./ 4HE 46 AND -OVIE 2ATINGS WILL BE EFFECTIVE -!34%2 $)3!",% 9%3 !LL 46 AND -OVIE 2ATINGS WILL BE BLOCKED OVERWRITING ALL PREVIOUS SETTINGS
46 2!4).'3
4O SELECT 46 2ATINGS HIGHLIGHT 46 2!4).'3 AND PRESS CURSOR q ON THE REMOTE CONTROL TO INVOKE THE 46 2ATINGS SUB MENU .AVIGATE WITH CURSOR a q OR ON THE REMOTE CONTROL TO SELECT THE RATINGS YOU WISH TO BLOCK 7HEN THE CURSOR IS IN THE DESIRED BRACKET PRESS OR a TO ACTIVATE IT !N 8 WILL APPEAR INDICATING THAT THE 46 2ATING HAS BEEN SELECTED 4O DESELECT PRESS OR a WHERE THE 8 IS 4HE 8 WILL DISAPPEAR INDICATING THAT THE 46 2ATING HAS BEEN DEACTIVATED
-/6)% 2!4).'3
4O SELECT -OVIE 2ATINGS HIGHLIGHT -/6)% 2!4).'3 AND PRESS CURSOR q ON THE REMOTE CONTROL TO INVOKE THE -OVIE 2ATINGS SUB MENU 0RESS CURSOR q OR ON THE REMOTE CONTROL TO TOGGLE BETWEEN 6IEW AND "LOCKED
# ! " "
46 3%450 -%.5 35" -%.53 #/.4).5%$ 3,%%04)-%2 /&& -). -). -). -). -). -). -). -). 7HEN THE 3,%%04)-%2 IS ACTIVATED THE 46 AUTOMATICALLY POWERS DOWN AFTER THE SPECIFIED PERIOD OF TIME .OTE 4HE 3,%%04)-%2 DIFFERS FROM %30 %NERGY 3AVING 0ROGRAMMABILITY IN THAT THE 3,%%04)-%2 COUNTDOWN IS UNAFFECTED BY ANY COMMAND FROM THE REMOTE CONTROL OR FRONT PANEL OF THE 46 %30 TIMER IS RESET WHEN IT RECEIVES A COMMAND FROM THE REMOTE CONTROL OR THE FRONT PANEL OF THE 46 .OTE 7HEN THE 3,%%04)-%2 IS ACTIVE THE CURRENT 3,%%04)-%2 COUNTDOWN TIMER VALUE APPEARS IN THE )46 COMMERCIAL 3%450 -%.5 AS WELL AS THE &%!452%3 -%.5 4HE 3,%%04)-%2 COUNTDOWN PERIOD CAN BE ADJUSTED OR RESET FROM EITHER MENU
#("' #)" "$%# % && *!$
3%#52)49 34!.$!2$ ()'( 4HIS FEATURE PROVIDES THE OPTION TO ENABLE ACCESS TO THE 3%450 -%.5 WITHOUT AN 2#'2 SETUP REMOTE CONTROL 34!.$!2$ 4HE 46 3%450 -%.5 CAN BE ACCESSED BY ENTERING A SPECIAL SECURITY CODE WITH A GUEST REMOTE CONTROL 2EFER TO 0HILIPS SALES REPRESENTATIVE FOR MORE DETAILS ()'( .OTE
4HE 46 3%450 -%.5 CAN BE ACCESSED ONLY WITH AN 2#'2 SETUP REMOTE CONTROL IN SETUP MODE 4HE DEFAULT 3%#52)49 SETTING FOR )NSTITUTIONAL 46 IS 34!.$!2$ 7HEN 3%#52)49 IS IN 34!.$!2$ MODE THE 46 IS MORE VULNERABLE TO UNAUTHORIZED OPERATION
This manual is brought to you by Anderic® and the staff at www.ReplacementRemotes.com
