Transcript
TIM J 5/16
USER MANUAL
10.b
11.a 11.b
10.a
11.c
10.f
10.g 11.d 12.a/b
10.c
10.d
10.h/i
9
1.a 4
8 3
1.c 1.b
2
5
6 13.a/b
7
11.e
FULL PART LIST: 1. Drum Head: a. 10” tom-tom head x 2 pcs b. 12” floor tom head x 2 pcs c. 16” bass drum head x 2 pcs 2. Assembled snare drum x 1 pcs 3. Assembled 8” tom-tom x 1 pcs 4. 10” tom-tom shell x 1 pc + hoop x 2 pcs + 2 locked lugs 5. 12” floor tom shell x 1 + pc + hoop x 2 pcs 6. 16” bass drum shell x 1 pc + hoop x 2 pcs 7. Seat of drum throne 8. 8” hi-hat x 1 pair 9. 10” cymbal x 1 pc 10. Spare Part carton: a. Cymbal stand x 1 pc b. Central tom holder x 1 pc c. Floor tom feet x 3 pcs d. Bass drum feet x 2 pcs e. Drum sticks x 1 pair f. 3” (7.5cm) lug for 10” tom-tom x 6 pcs g. 4.3” (11cm) lug for 12” floor tom x 8 pcs h. 6” (15cm) lug for 16” bass drum x 8 pcs i. Bass drum lug hook x 8 pcs j. Lug spacers x 22 pcs k. Drum key x 1 pc 11. Hi-hat Stand carton: a. Pull rod x 1 pc b. Clutch x 1 pc c. Top section tube x 1 pc d. Feet section x 1 pc e. Feet section of drum throne 12. Snare Stand carton: a. Basket arm x 1 pc b. Feet stand x 1 pc 13. Drum Pedal carton: a. Drum pedal x 1 pc b. Beater x 1 pc
a. HI-HAT
Insert the foot pedal rod and tighten.
Top hi-hat x 1 1
2
Bottom hi-hat x 1 Feet section
Top section
Tighten the feet & foot pedal rod.
Open the feet and make sure all feet are well secured to the ground. 3
4
Take out the pull rod from the top-section tube and leave the clutch aside. 5
Insert the pull rod and tighten. 6
od Pull r Top-section tube Clutch
Insert the top-section tube and tighten. 7
Place the bottom hi-hat. 8
Disassemble the clutch.
Place the top hi-hat on the clutch rod.
9
10
Assemble the felt and the screw back. 11
Fit the top hi-hat on the pull rod and tighten the screw. 12
You may leave some space for playing open and close sound
Adjustable tilter for adjusting the angle of bottom hi-hat
b. Throne Pull open the legs and tighten. 1
2
Seat
Feet
Adjustable tube
Set the throne to appropriate height and tighten. 3
Fit seat to the stand and tighten. 4
c. Snare drum 1
Pull open the legs and tighten. 2
Assembled snare drum Stand-feet Basket arm
3
Insert the basket arm to appropriate height and tighten. 4
2. open the arms
1. adjust the arm to horizontal position and tighten
Place the snare drum on basket. 5
3.loose the screw and pull the arm
You may adjust the snare by tuning the knob. 6
d. Floor tom & 10” tom-tom 1
12” Head x2 pcs drum key x1 pc
Place a head on the floor tom. 2
Floor tom Leg x 3 pcs
Hoop x2 pcs
Tension rod & spacer x 8 pcs
Place the hoop onto the head. 3
The holes on the hoop should be straight to the lug
Screw the tension rod to the lug. NOTE: DO NOT FULLY TIGHTEN 4
Rod Spacer Hoop Lug
Repeat the same procedure on the other side until all lugs are half screwed. 5
Use the drum key to tune the tension rod. 6
1st
4th
3rd
2nd
Note: Do not fully tighten one rod at a time. Please tune rods in the diametrical order as above. Repeat several times until the tension of each rod is equal. The higher tension you tune , the higher pitch it would sound
Insert the floor tom legs into the leg bracket to appropriate height and tighten. 7
8
e. Bass drum Hoop x2 pcs
Prepare 8 sets of bass drum tension rod + spacer + bracket
Bass drum x1
1
2
Drum key Bass drum head x2pcs
3
5
tension rod set x8 sets
1. Place the head with logo on the front side of the bass drum. 2. Place the hoop onto the drum head.
Screw the tension rod to the lug. NOTE: DO NOT FULLY TIGHTEN 4
Repeat the same procedure on the other side until all rods are half screwed.
Use the drum key to tune the tension rod. 1st
6 4th
3rd
2nd
Note: Do not fully tighten one rod at a time. Please tune rods in the diametrical order as above. Repeat several times until the tension of each rod is equal. The higher tension you tune , the higher pitch it would sound
Insert the legs to the leg bracket and tighten. 7
8
Bass drum leg x 2 pcs
f. Tom-tom, cymbal arm & bass drum pedal Insert the tom tom holder to the holder bracket and tighten. 1
Hang 8” and 10” tom tom on the holder The logo should face the audience. 2
Insert the cymbal arm to the holder bracket and tighten. 3
Unscrew the cymbal lock and leave single felt on the holder. 4
1. Place the cymbal between 2 felts. 2. Place the spacer on the top. 3. Lock the cymbal. 5
Don’t forget to connect your bass drum pedal before playing. 6
Notes:
Notes:
