Transcript
www.rohlhome.com
3-Hole Widespread Faucet ROHL Country Bath Arcana
AC107L-2 (Ornate Metal Lever) AC107LM-2 (Classic Metal Lever) AC107X-2 (Cross Handle) AC107OP-2 (Ornate Porcelain Lever)
FEATURES • 3 x 1 3/8” cutouts • 1/4-turn ceramic disc valves • Fixed spout • Pop-up drain, 1 1/4” pipe • Spout, valve housing, and popup made from solid brass • 7 1/2” overall height • 1.2 GPM
FINISHES •Polished Chrome •Polished Nickel •Satin Nickel •Tuscan Brass •Inca Brass
WARRANTY • Limited Lifetime* * No Warranty on Tuscan Brass Finish (TCB)
AC107X
AC107L
AC107OP
AC107LM
Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
www.rohlhome.com
AC107-2 Spare Parts
Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
www.rohlhome.com
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PRELIMINARY INFORMATION - We recommend the use of a professional plumber - Flush the plumbing system before installation of the mixer. This will prevent residue from clogging the line and aerator. Especially important in new construction. - Mixers of the ARCANA series are fit for operating with hot water collectors under pressure, instantaneous and gas water-heaters TECHNICAL DATA - Minimum dynamic pressure ……………….7.25 psi - Maximum operational pressure (static)……145 psi - Recommended operational pressure(static)..14.5-72.5 psi (N.B.: for pressures higher than 72.5 psi we suggest the installation of a pressure reducer) - Maximum test pressure (static)……………..232 psi - Maximum hot water temperature ………….176°F - Suggested hot water temperature ………….140°F (for energy saving) - Hot water connection ……………………… left - Cold water connection …………………….. right - Flow rate…………………………max 1.5gpm @ 60 psi SPOUT INSTALLATION - Screw the flexible hoses (5) to the mixer using a 7/16 ” crescent wrench positioning it in the special millings. - IMPORTANT: during the flexible hose assembly operations, DO NOT HOLD the sleeve of the flexible hose with VICE GRIPS OR ADJUSTABLE PLIERS, this could damage them, and would compromise the safety of the installation. - Screw the fixing stem (9-4) on the spout (7). - Insert the spout (7) in the central hole of the lavatory (min. 0 1” 3/8); placing the packing (9-1) between the spout and the lavatory. - Fix the spout on the ceramics by a shaped packing (9-2), fixing clamp (9-3) and hexagonal check-nut; using a ½” crescent wrench. - Insert the pop-up’ s rod (8-3) and screw the knob (8-1). - Connect the lower rod (8-5) to the upper rod (8-3) by the connection(8-4) and using a ¼” wrench. HEADVALVE INSTALLATION 1. Screw a mounting nut (2-1) on the tail-piece (3-2) and mount first a gasket (2-2); then a seal (2-3) 2. Insert the tail piece into the side hole of the sink (min. 01”18) 3. Assemble the other seal (2-3); then the other gasket (2-2) and then screw down the other mounting nut.
4. The head valves height on the sink should be between min. 1 ¾” and max. 2 1/8” (recommended height 1 7/8"). 5. Screw the flexible hose (5) to the cross connection and insert the seals (4). 6. Screw down the joint (1-5) on the tailpiece. 7. Assemble on the rod (A) of the head valve (3-1) the extension (1-4) first; then the handle (1-7) (10-7) (11-7) on the extension and place the gasket (13) inside the handle. 8. Screw down the screw (1-3) and mount the cover cap (1-2) POP UP DRAIN INSTALLATION 1. Insert the drain (6-2) into the hole of the sink. Use an approved sealant under the drain (6-2) to make a watertight seal. 2. Mount on the drain the tapered seal (6-4) first; then the gasket (6-5) and screw down the check nut (6-6). 3. Screw the body (6-7) to the drain. 4. Unscrew the nut (6-9), insert the horizontal rod (6-8) into the body; taking care that the end is inserted into the hole (B) on the plug (6-1) and then mount the nut again. 5. Connect the stick (8-5) with the horizontal rod (6-8), using the connection piece (8-2). MAINTENANCE The faucets are fitted with an aeration device in the Hot/Cold water outlet. This may need occasional cleaning especially in hard water areas. This is accomplished by unscrewing the outlet in a counter clockwise direction, dismantling and leaving the inner screen mesh immersed over night in a solution of a 50% / 50% solution of vinegar and water. WARRANTY INFORMATION There is no warranty on the Tuscan Brass finish.
Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
w
www.rohlhome.com
INSTALLATION INSTRUCTIONS
FINISH CARE 1. 2. 3.
4.
WIPE DOWN AFTER USE TO AVOID SPOTTING USE A SOFT BRUSH FOR DETAIL CLEANING DO NOT USE SPRAY CLEANERS WITH AMMONIA, ALCOHOL OR BLEACH DO NOT USE ABRASIVES LIKE COMET, AJAX OR BONAMI
FINISH CHROME
CLEANING 50-50 VINEGAR AND WATER
CARE FLITZ WAX OR GAGNON, SIMICHROME
INCA BRASS
50-50 VINEGAR AND WATER
DO NOT USE FLITZ – GAGNON OK
POLISHED NICKEL
50-50 VINEGAR AND WATER
FLITZ WAX OR GAGNON, SIMICRHOME
SATIN NICKEL
50-50 VINEGAR AND WATER
FLITZ WAX OR GAGNON
TUSCAN BRASS
PAT DRY AFTER USE
FLITZ WAX. NO WARRANTY. DO NOT RUB OR WIPE.
FOR WATER SPOTTING ON CHROME, POLISHED NICKEL OR SATIN NICKEL, USE SIMICHROME PASTE.
ROHL LLC 3 PARKER IRVINE, CA 92618-1605 USA Phone: 800.777.9762 Fax: 714.557.8635 www.rohlhome.com
Rubinetteria CISAL S.p.A. Via Pietro Durio, 160 28010 Alzo di Pella (Novara) – ITALIA Tel.+39.0322.918111 – Fax +39.0322.969518 E-mail:
[email protected] - www.cisal.it
Consult your local ROHL showroom for additional information and specifications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
