Rotary Push-control Wall Dimmer

Transcript

RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 1 OF 6 Rotary Push-control Wall Dimmer RPC series 0-10V dimming and switching rotary module to fit into plates and grid systems Contents Product order codes Technical specification and installation 2 Related product options 3 Wiring diagrams RPC wired to LC100R/T 3 Two RPCs wired to LC200R/T 4 RPC wired to Trailing-edge Dimmer ADT400 4 RPC wired to Leading-edge Dimmer AD2500 5 RPC wired to LEDrose LDR100 with mains switching 5 RPC wired to LEDrose LDR100 without mains switching 6 RPC1 2-wire control of a single drive unit or a Multiload dimming and switching product RPC2 2-wire control of between 2-20 drives or Multiload dimming and switching products Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 2 OF 6 Technical specification and installation minimum brightness preset DC 0-10V C1 C2 maximum brightness preset 0-10V control terminals front view back view top view Modules can be supplied to fit wall plates and grid systems from UK wall-plate manufacturers. Contact Multiload on +44 (0) 20 7794 9152 to ensure compatibility with specified plate type and finish. Shown above is module supplied for fitting into MKGridPlus. Functions Installation and set up procedure Rotary Push-control Wall Dimmers RPC provide 2-wire control, dimming and switching, of control gear accepting 0-10V and 1-10V signals. Installation should be carried out by suitably qualified personnel in accordance with good electrical practice and the appropriate national wiring regulations. This control gear includes Multiload products such as: Switch off mains electrical supply before commencing installation. • Lighting Contactors LC series mains switching and boosted 0-10V and 1-10V dimming Trailing-edge Dimmer ADT400 with internal relay for mains switching Leading-edge Dimmer AD2500 with internal relay for mains switching • LED drivers dimmable to zero such as LEDrose LDR100 The device may be used for interior installations in dry locations with suitable surface plates fitted. Terminals C1 (-ve 0V) C2 (+ve 0-10V) Low voltage 2-wire 0-10V analogue control by rotation of the control knob. Setting minimum and maximum brightness • Other manufacturers control gear accepting 0-10V or 1-10V signals that source 100mA at 10V at the signal input with RPC Easy access minimum and maximum brightness screwdriver presets set the dimming range covered by the rotary control. Technical specification Set the minimum preset first: setting the maximum will not affect minimum setting. Brightness levels are not affected by temperature changes around the module. RPC1 for a single drive only RPC2 for 2 to 20 drives This module can be wired to a number of LED drivers or fluorescent ballasts or other 0-10V and 1-10V controlled drive units. The control signal is stabilised so that adding or removing a drive unit will not materially affect the brightness. Environmental specification Temperature range: -10ºC – +50ºC Maximum humidity: Less than 95% non-condensing Signal output: 0-10V DC (sink current capability only, allowing use with standard drives, such as LED drivers and fluorescent ballasts) Dimensions: MK module L:50mm W:25mm D:30mm Knob Diam: 20mm H:13mm Fixing: Bush M10 Shaft:6mm Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 3 OF 6 Rotary Push-control Wall Dimmer RPC related product options PROTECTED MAINS VOLTAGE SUPPLY 230V CONTROL SIGNAL 0-10V ONLY ONE CONTROL SIGNAL OPTION TO BE CONNECTED Lighting Contactor LC100 Lighting Contactor Lighting Contactor LC100 LC100 Trailing-edge Dimmer ADT400 LeadingEdge Dimmer AD2500 24V POWER SUPPLY DIMMABLE DRIVE VoltMaster Intelligent Transformer LEDrose LDR100 LED CONSTANT VOLTAGE LED CONSTANT CURRENT FLUORESCENT BALLAST LOW VOLTAGE DRIVE LED DRIVE ROTARY DIMMING 3RD PARTY DRIVES VoltMaster VMD series Intelligent Transformer 35W-400W with LC100 LEDrose LDR100 Constant Current Dimmable Driver with LC100 RPC1: for a single drive RPC2: for 2-25 drive units Lighting Contactor LC100 provides a boosted 0-10V signal output Output: 12V / 24V AC Output: 100-750mA max Output: 0-10V signal sink Dimmable drive Output MAINS VOLTAGE DIMMING & SWITCHING MAINS VOLTAGE DIMMING & SWITCHING Trailing-edge Dimmer ADT400 10W-400W max Leading-edge Dimmer AD2500 40W - 2.3kVA Output: 230V variable Output: 230V variable [email protected] www.multiload.co.uk RPC1 wired to Lighting Contactor LC100R/T Both dimming and mains switching activated from Rotary Push-control Wall Dimmer using only 2-core signal cable L SUITABLY RATED CIRCUIT PROTECTION N E TO ADDITIONAL DRIVES E L N INPUT 1-10V DIMMABLE DRIVE LED / FLUORESCENT L2 ON OFF SIG 0V C1 C2 15V INPUT A OUTPUT A L N L1 N GLOBAL SIG OUT A SIG IN A OUT LIGHTING CONTACTOR LC100R/T RPC1 OUTPUT SIGNAL + – C1 C2 – + TO ADDITIONAL DRIVES DRAWING NOT TO SCALE WD-RPC-LC100. ISS-1-0116 Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 4 OF 6 Two RPC1s wired to Lighting Contactor LC200R/T SUITABLY RATED CIRCUIT PROTECTION L N E TO ADDITIONAL DRIVES TO ADDITIONAL DRIVES + – – + E L N OUTPUT SIGNAL INPUT 1-10V DIMMABLE DRIVE LED / FLUORESCENT 1-10V DIMMABLE DRIVE LED / FLUORESCENT INPUT OUTPUT SIGNAL E L + – N – + L2 ON OFF SIG 0V C1 C2 15V INPUT A OUTPUT A L N L1 N GLOBAL SIG OUT A SIG IN A OUT LIGHTING CONTACTOR LC200R/T C1 C2 RPC1 INPUT B OUTPUT B L N L1 N L2 RPC1 GLOBAL SIG OUT B SIG IN B IN ON OFF SIG 0V C1 C2 15V C1 C2 TO ADDITIONAL DRIVES TO ADDITIONAL DRIVES DRAWING NOT TO SCALE WD-RPC-LC200. ISS-1-0116 RPC wired to Trailing-edge Dimmer ADT400 LOAD 10W–400W SUITABLY RATED CIRCUIT PROTECTION L N L L L N N SUPPLY 230V N VL N VL1 LOAD OUTPUT TRAILING-EDGE DIMMER ADT400 RPC1 GLOBAL DC OUT SIGNAL INPUT 0V ON 0V OFF 0V 15V C1 C2 C1 C2 Rotary Push-control Wall Dimmer RPC2 is used when controlling a circuit with more than one Trailing-edge Dimmer ADT400 0-10V SIGNAL SELV DRAWING NOT TO SCALE WD-RPC-ADT400. ISS-1-0116 Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 5 OF 6 RPC wired to Leading-edge Dimmer AD2500 SUITABLY RATED CIRCUIT PROTECTION L N E LOAD 40W – 2.3kVA E L N INPUT N VL SL OUTPUT LEADING-EDGE DIMMER AD2500 RPC1 INPUT OUT IN 0V C1 C2 Rotary Push-control Wall Dimmer RPC2 is used when controlling a circuit with more than one Leading-edge Dimmer AD2500 BOOSTED SIGNAL OUTPUT DRAWING NOT TO SCALE WD-RPC-AD2500. ISS-1-0116 RPC wired to LEDrose LDR100 with mains switching SUITABLY RATED CIRCUIT PROTECTION L N E L LEDrose DC C2 C1 C2 C1 NC DIM CONTROL LDR100 N E POWER SUPPLY 24V DC L2 ON OFF SIG 0V C1 C2 15V INPUT A OUTPUT A L N L1 N GLOBALSIG OUT ASIG IN A OUT LIGHTING CONTACTOR LC100R/T C1 C2 LED 15V 0V +ve -ve RPC1 DC OUTPUT – + 15V To additional LEDrose LDR100 Combination of which must be within 85% of the rating of the power supply DRAWING NOT TO SCALE WD-RPC-LDR100. ISS-2-0117 Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk RPC-3-0217. ROTARY PUSH-CONTROL WALL DIMMERS. PAGE 6 OF 6 RPC wired to LEDrose LDR100 without mains switching L SUITABLY RATED CIRCUIT PROTECTION N L N E POWER SUPPLY 24V DC DC OUTPUT RPC1 – + LEDrose C2 C1 C2 C1 NC DIM CONTROL LDR100 DC LED 15V 0V +ve -ve C1 C2 To additional LEDrose LDR100 Combination of which must be within 85% of the rating of the power supply Use RPC2 when more than one LEDrose LDR100 is installed DRAWING NOT TO SCALE WD-RPC-LDR100. ISS-2-0117 Multiload 2 Rosemont Road Hampstead London NW3 6NE Telephone +44 (0) 20 7794 9152 www.multiload.co.uk