Royal Robotic Vacuum Cleaner With Lcd Docking Station Operation Manual

Transcript

Robotic Vacuum Cleaner With LCD Docking Station Operation Manual Royal Robot 1300 TABLE OF CONTENTS SAFETY INSTRUCTIONS --------------------------------------------------- 2 * Safety Instructions * Battery and Recharging Instructions SPECIAL FEATURES -------------------------------------------------------- 3 MAJOR COMPONENTS AND ATTACHMENTS ------------------------ 3 OVERVIEW OF THE ROYAL ROBOT 1300------------------------------- 4 UV(ULTRAVIOLET) LIGHT SWITCH AND WARNING ---------------- 5 INSTALLATION GUIDE ------------------------------------------------------- 6 * Proof Test * Installing and Removing Side Brush * Removing Paper Holder * Installing Dusting Paper and Holder * Installing and Removing Remote Control Battery * Battery Installation and Removal * Recharging Battery ADJUSTMENT OF ANTI-CLIFF SENSORS ---------------------------- 12 GENERAL OPERATION ----------------------------------------------------- 13 * Preparation for Operation * Control Panel * Remote Control * Control Panel of Docking Station * Basic Operation * Select working time and function presented CLEANING AND MAINTENANCE ---------------------------------------- 18 * Maintenance Method * Cleaning Dust Bin * Cleaning Intake * Cleaning Side Brushes TROUBLESHOOTING ------------------------------------------------------- 22 WARNING OF BATTERY & ADAPTOR USAGE ----------------------- 23 1 SAFETY INSTRUCTIONS Please read the safety instructions in the Operation Manual before operating Royal Robot 1300 and keep this manual handy for your future reference. Observe the basic safety rules to prevent any occurrence of fire, electric shock and personal injury. Safety Instructions 1. Please read the Operation Manual before operating Royal Robot 1300. 2. Do not operate Royal Robot 1300 outdoors. 3. Before starting Royal Robot 1300, be sure to install dust bin filter properly in case of any damage of Royal Robot 1300. 4. Do not operate Royal Robot 1300 on wet floor or in moisture conditions, e.g. bathroom. Water and moisture could damage the circuit board in e. 5. Prior to operate Royal Robot 1300 remove any loose articles on the floor such as clothes, paper, loose cables, and extension cords as well as making sure to lift curtains and drapes off the floor to avoid any possible accidents. In case of a loose cable is tangled with Royal Robot 1300, the cable might move around with Royal Robot 1300 as Royal Robot 1300 works and topple down the table, chairs, or cabinet and cause property damage. 6. Never stand or sit on Royal Robot 1300. Beware of children or pets while Royal Robot 1300 is in operation. 7. Never use Royal Robot 1300 to clean up sparking cigarette butts or burning ashes from fireplace. 8. Never use Royal Robot 1300 to clean up combustible or highly volatile liquids such as gasoline. 9. While Royal Robot 1300 is in operation, make sure all doors leading outside are closed. 10. During operation, the heat vent should avoid being clogged. If heat vent clogged, Royal Robot 1300 could be damaged. 11. If Royal Robot 1300 is malfunctioned or damaged by force, do not operate Royal Robot 1300 regardless the cause. Please call your local dealer for service information. 12. Turn off the power and remove the battery from Royal Robot 1300 if the unit will not in use for a long period of time. 13. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by person responsible for their safety. ---Children should be supervised to ensure that they do not play with the appliance. 14. Plug must be removed from the socket-outlet before cleaning or maintaining the appliance. 15. Automatic battery-operated cleaners shall also be provided with cautionary instructions for room preparation and constant care. Battery and Recharging Instructions 1. The battery is rechargeable. Please use the voltage and current specified on the Packing. If you are not sure of the voltage and current of your house, please contact your local power company or a licensed electrician. 2. Use only the battery supplied with your Royal Robot 1300. 3. Charging adaptor is for indoors only. 4. Use only the charging adaptor supplied with your Royal Robot 1300. 5. Do not recharge the battery if the cable or plug of the battery is damaged. 6. Never touch the charger, plug or cable with damp hands. 7. If Royal Robot 1300 requires cleaning, unplug the adaptor, switch off the unit and take out the battery. 8. Please take out the battery pack before disposing of the unit. 9. Please switch off Royal Robot 1300 before taking out the battery. 10. Please recycle and dispose the waste battery properly. 2 SPECIAL FEATURES Congratulations on purchases the Royal Robot 1300 Robotic Vacuum Cleaner With LCD Docking Station. This revolution Robotic Vacuum Cleaner With LCD Docking Station is equipped with functions suitable for cleaning up floor surfaces of home and office such as wood, tile, and linoleum. Royal Robot 1300 Robotic Vacuum Cleaner With LCD Docking Station is definitely a household helper. Working Patterns: Random Spiral Along the wall Spiral "Z" Type MAJOR COMPONENTS AND ATTACHMENTS Royal Robot 1300 x1 Rechargeable Battery x1 Adaptor x1 Manua Dust Bin Filter x1 Dusting Paper x3 Side Brush x 2 Dusting paper holder x1 Remote Control x1 3 l Operation Manual x1 Docking station x1 OVERVIEW OF THE ROYAL ROBOT 1300 Top cover (Dust Bin in side) LCD Control Panel Heat Vent LED Indicator Bumper Contact plates for automatic charging Control Panel Front Small Wheel Side Brush & Cap Anti-Cliff sensor Intake Valve Left and Right Wheels Side Brush & Cap Wheel Cover Battery cover UV Light D.C. jack Power switch 4 UV(ULTRAVIOLET) LIGHT SWITCH AND WARNING CAUTION!! "Do not stare at the UV light!" (UV)Ultraviolet light is dangerous to your eyes. Even a short exposure can damage your eyes, cause severe irritation and possible loss of sight. TURN OFF THE UV LIGHT SWITCH WHEN INSTALLING AND REMOVING: INSTALLING AND REMOVING SIDE BRUSH BATTERY INSTALLATION AND REMOVAL ADJUSTMENT OF ANTI-CLIFF SENSORS INSTALL THE DUSTING PAPER HOLDER UV Light Switch UV Light You may turned on the UV light after make change on Side brush, Battery and Anti-Cliff sensors. It is not necessary to turn on the UV light when Dusting paper holder is installed. 5 INSTALLATION GUIDE Proof Test: Please try either one of the following two methods to test the installation of docking station, if the vacuum cannot go back to the docking station and charge successfully, then please replace the docking station to the proper height. 1. Test by the unit, press down the selection button, do not release, and turn on the power switch of the unit, when the unit begins to move, release the selection button. The unit will switch the mode to return to the Docking Station for charging. Please refer to Fig.1. 2. Test by the remote control, turn on the power switch of the unit, press the button "Docking" on the remote control, the unit will go back to the docking station for recharging. Please refer to Fig. 2. selection button Keep pressing Fig. 1 Power switch Press " Docking " Fig. 2 Power switch on 6 INSTALLATION GUIDE ＊Make sure the power switch of T285D and UV light are turned off. Installing and Removing Side Brush: To install: Remove the side brush caps from the bottom of cleaner. Put the brushes directly onto the holder and press on the caps to fix it.(Fig. 3) Then spread the brush bristle evenly as shown in Fig. 5 To remove: Hold the brush bristle and pull upward to remove the brush.(Fig. 4) PULL UP! Fig. 5 Side brush holder PRESS PULL UP! HOLD Fig. 4 Fig. 3 ＊Make sure the power switch of T285D and UV light are turned off. (Please refer to page 5.) Removing Paper Holder: Remove the dusting paper holder following the instruction as below diagram. 2 Lift up 1 Push to the left 7 INSTALLATION GUIDE ＊Make sure the power switch of Royal Robot 1300 and UV light are turned off . (Please refer to page 5.) Installing Dusting Paper and Holder: 1. Flat the dusting paper and put it on the floor or table. Then place the holder (the side with 4 stoppers face up) on the paper at the midpoint as below diagram. Stoppers Hole for the stopper Dusting Paper 2. Remove 4 stoppers from the holder, fold the hem of dusting paper on two sides back to the holder, and place back 4 stoppers on top of the paper then press firmly to fix the paper onto holder as below diagram. Fold back 4 5 Press Press 6 3 Press 2 Press 1 Fold back Finished ! 3. Place the dusting paper holder to the bottom of unit by aiming one bolt of holder at the hole (near the big wheel) on cleaner, click the holder on the cleaner, and then do it again for the other side. Press the two bolts on the dusting paper holder into the two holes on the bottom of the cleaner. NOTE: 1. Do not use mopping function on the carpet. At the same time you should remove the side brushes to prevent it from damaging the brushes. 2. If you don’t need to use mopping function, please remove the dusting paper holder from the cleaner before you turn it on for cleaning. 8 INSTALLATION GUIDE Installing and Removing Remote Control Battery: ※Remove insulation sheet before use remote. Turn the Remote Control upside down. Press position A and pull out position B of the battery slot at same time. Put the battery with the positive “+” side facing up. Push-in the battery slot as below diagram.. A B 9 INSTALLATION GUIDE Battery Installation and Removal: 1. Make sure the power switch of Royal Robot 1300 is turned off. 2. Press the two points “A” (marked in the below diagram) and slide the battery cover in the direction of arrow “B” (marked in the below diagram). 3. Insert the battery into the battery compartment. Be sure to orient the battery contacts with those of the unit. Slide back the battery cover to close it. A B 10 INSTALLATION GUIDE Recharging Battery: 1. Before charging, please check if the battery is properly mounted and turn on the power switch. 2. Two ways to charge the battery: A. Plug the d.c. end of the adaptor into d.c. jack at the side of the unit first, and then plug the a.c end of the adaptor into the a.c. power outlet on the wall. (Please connect the adaptor to the unit first before connecting to the a.c power outlet.) Adaptor plug D.C. jack B. Make sure the docking station is installed properly, place the unit to the docking station, make sure the contact points at the back of the unit is contacted with the contact plate at the docking station. 10 Dust bin full Charging Battery low 0c m 30 cm 3. When charging, the LED indicator below the “ ” (CHARGING) on Royal Robot 1300 (as above diagram) will flash green, and it will stay green when the cleaner has been uninterruptedly charged for 6~8 hours. 4. When the Royal Robot 1300 is in "Battery Low" situation, the LED indicator below the“ ” (BATTERY LOW) (as above diagram) will stay in RED. 11 ADJUSTMENT OF ANTI-CLIFF SENSORS sure the power switch of Royal Robot 1300 and UV light are turned off. ＊Make There are three “Anti-Cliff” sensors at the bottom of Royal Robot 1300 to prevent the unit from falling down stairs.If the distance between the stair and the ground is shorter than usual, please adjust all windows of “Anti-cliff” sensors to “◎” or “◎” or “◎” or “ ” position to prevent the cleaner from falling down stairs. Please test it before it starts to clean. ◎ The Criteria of Adjustment Darker floor Lighter floor Bigger drop Shorter drop ＊ATTENTION: If the color of the floor is dark (ex. Black), it means that reflectivity of the floor is bad, at this time, you have to open the window to a larger scale. Please refer to the criteria of adjustment for adjusting the windows. 12 GENERAL OPERATION Preparation for Operation: 1. Install the side brushes and install the battery according to the manual. 2. Turn off the power switch on the side of the unit, and charge the battery directly from D.C. Jack for 6~8 hours prior to the first operation. 3. To ensure the best efficiency of the unit, first is to remove clothes, paper, cable, extension cable scattered on the floor, roll up the curtains and drapes if any to avert the possible accident. In case of the cable entangled with the cleaner, the cable could move around as the cleaner is working and might topple down the table, chairs, even cabinet or cupboard. Control Panel: Working time selection buttom IR receiver 20 minutes working time indication lamp 13 Max working time indication lamp 40 minutes working time indication lamp GENERAL OPERATION Remote Control: ※Remove insulation sheet before use remote. IR transmitter (2) Forward (1) Auto (4) Turn Right (3) Turn Left (5) Stop (6) Backward (7) Vacuum switch (9) Spiral (8) Docking (10) Random (11) Along the wall (12) “Z” type 1. " CR2025 3V " battery required. 2. Function of buttons: Key Pressed AUTO FORWARD Action Start the unit. Select the work time(Please refer to page 17). Move forward with vacuum on and will stop when bumper encounter any obstacle or by pressing “STOP” button. LEFT Turn left . Pressing and holding the button makes it turn left continuously. RIGHT Turn right . Pressing and holding the button makes it turn right continuously. STOP Stop the unit immediately. BACKWARD VACUUM DOCKING SPIRAL RANDOM ALONG THE WALL Z TYPE The unit going backward for 20 cm.The unit doesn't have the back anti-cliff sensor to prevent it from falling from stairs when moving backward. Switch the vacuum power or to turn off vacuum and sweeper (with mop function on only). Search the docking station for recharge. Move in spiral pattern with vacuum on until the bumper encounter an obstacle or stairs, then the unit will continue operate in “AUTO” mode with max. working time and until battery low. Operate in the random mode continuously until the battery low. Operates unit in the along-the-wall mode continuously until the battery low. Operates unit in the “Z” type mode continuously until the battery low. 14 GENERAL OPERATION Control Panel of Docking Station: Present Time Setting Battery Indicator Completed setting for time of cleaning Hour Minute Day of Week 4 1 23 Functions of buttons: ＊ "Set": Press “Set” to switch between setting the "CLK" present time and “ ” the working schedule. A. Set present time:  Press 1 "Set" once, "SET" , " CLK" will flash.  Press 2 "Select" to switch among time setting modes of Hour, Minute, and Day of Week.  Press 3 “+” and 4 “-” for adjustment of the digits.  Press 1 "Set" again when finish time setting. B. Set working schedule:  Press "Set" twice, “ ” (on the left side of the screen) will flash. Press "Select" to switch among "Hour" /"Minute" / "Day of Week" to do the setting as described in paragraph A. If no time setting was done before, the screen will show “--:--”, press “+” and “-” to adjust the digits. *** With “ ” shown on the LCD display indicates the working schedule is set completely. ＊ “+”: Press “+” for increment adjustment purpose. ＊ “-”: Press “-“ for decrement adjustment purpose. Format of schedules: a. Work everyday (Su-Sa light on). b. Five days a week (Mo-Fr light on). c. Six days a week (Mo-Sa light on). d. Two days a week (Su and Sa light on only). e. Once a week (Any one day of the week light on). 15 GENERAL OPERATION Basic Operation: →Manual work ※When LED Indicator lights on. → Check: Œ . Dust bin is full.  . Intake Valve is stuck with dirt. Ž . Wipe out the inner and outside of Intake Valve area. 1. Press the “Working time selection buttom” on the control panel to select the work time: 20 Short, about 20 minutes, 40 Middle, about 40 minutes, Max Max, until battery low. Please refer to page 17 for selection sequence details. Pressed after 2 seconds later, the unit begins cleaning automatically. 2. After the work is completed, the unit will emit a buzz of warning and stop. If the power indication lamp turns to Red (battery low) at the same time, the unit will buzz twice of warning every minute indicating that the battery needs immediate charging. Stop operation 1. To stop the operation of the unit immediately, you can turn off the power switch on the right of the unit, or lift the unit off the floor, the unit will stop 7 seconds later. 2. If you want the unit to continue working, place the unit on the floor and reset the power switch of the cleaner and select the working time as expected. Safety Devices 1. The unit will stop after 7 seconds lifted up from the floor. 2. The unit will STOP when wheel jammed for more than 7 seconds. →By Remote Control 1. Press “Auto” button to start cleaning. 2. Press “Stop” button to stop cleaning. 3. Other functions please refer to the table listed on page 14 as “ Function of buttons “ . 16 GENERAL OPERATION Select working time and function presented: LED indication and sequence Function Presented Max Light on Maximum working time with docking function ON. 40 Light on 40 minutes working time with docking function ON. 20 Light on 20 minutes working time with docking function ON. Max Flash Maximum working time with docking function OFF. 40 Flash 40 minutes working time with docking function OFF. 20 Flash 20 minutes working time with docking function OFF. Stop. 17 CLEANING AND MAINTENANCE Maintenance Method: The operation and maintenance of the Royal Robot 1300 is very simple. After each use, clean any dirt left behind on the dust bin and filter. It is not necessary to clean the intake after every use. Cleaning Dust Bin: 1. Lift up the cover at "A" in the direction as arrow "B" shown in below diagram to remove the Top Cover from the cleaner. B A 2. Take out the dust bin from the cleaner. 18 CLEANING AND MAINTENANCE 3. Open the upper cover of the dust bin. 4. Lift up and take out the filter. 5. Throw away the dust and dirt from the dust bin. 19 CLEANING AND MAINTENANCE 6. Rinse the dust bin with tap water. It is not necessary to wash every time. Please do not put it into the washing machine to do the cleaning. 7. Periodically clean the filter with a soft bristle brush. 8. Once dry, reinstall the filter and the dust bin lid. 9. Place back the dust bin and the Top Cover ATTENTION!! Before starting the cleaner, please be sure the dust bin filter has properly installed in case any damage occurs. 20 CLEANING AND MAINTENANCE Cleaning Intake: After repeated use, dirt and dust can accumulate around the intake of the T285D and the working efficiency can be reduced. To ensure the best efficiency and constant airflow, the intake should be cleaned periodically. Intake Valve Cleaning Side Brushes: 1. After being used for a period of time, the brushes need to be replaced for working more effectively. 2. Turn off the power, place bottom of the cleaner upward on a flat surface. Hold the brush bristle and pull upward to remove the brush. 3. The side brushes can be rinsed and if they become crooked, you can soak them in hot water to make them recover to the original shape. Install the brushes back after cleaning. HOLD PULL UP! 21 TROUBLESHOOTING Problem Possible Cause Solution 1 LED stays red after power on. 1.Battery Low condition. 2.The wheels stuck. 1.Recharge the cleaner. 2.Remove T285D from obstacles. 2 T285D could not vacuum effectively when it is turned on. The dust bin filter is not properly installed. Install the dust bin filter properly. 3 T285D is moving backwards after being started. T285D is on the floor in darker color (it means the reflectivity of floor is bad). Please adjust all windows of “Anti-cliff” sensors. (Please refer to page 12.) 4 The side brush becomes crooked, not good to sweep. Being used for a long time. If it becomes crooked, you could soak it in hot water to have it recover to its original shape. 5 1.To install the battery properly, please refer to page 10 for 1.The battery is not installed battery installation. properly. 2.Have the battery fully Cannot start the T285D. 2.Battery power is low. charged. 3.The Top Cover is not 3.Place back the Top Cover installed properly. and turn it on again. T285D circles around only. One of the wires of the wheels is loosened. Open the wheel cover and connect the loosened wire of the wheel set properly or contact your local dealer for service. 7 Remote control doesn't work. 1. The battery for the remote control is exhausted. 2. The “CR2025 3V” battery is not installed correctly or not installed. 3. The unit and remote control are exposed in the sunlight or strong light. 1. Change a new set of battery. 2. Re-install the battery correctly. 3. Please close the curtain to avoid the unit directly exposed to sunlight . 8 1. The power switch of the Can't use the remote unit is not on. to control the unit while 2. The distance is beyond it is in docking station. the threshold. 6 1. Turn on the power switch. 2. Move forward within the acceptable range. ※ If the solution can not solve the problem, please contact your local dealer for service. 22 WARNING OF BATTERY & ADAPTOR USAGE 1. Please follow the voltage and current specified and printed on the packing labels. Check with salesman or local power company if it is uncertain. 2. Please apply the same model’s battery (D.C. 14.4V 1500mAh) and adaptor (19V 600mA) as equipped with the packing. 3. Forbid any un-rechargeable or different type/model battery. 4. To avoid the hazard from battery short circuit, please follow the instruction of installing battery exactly. 5. The adaptor is applied indoors only. 6. Do not keep on using the equipped battery if the packing cast is broken. 7. Never touch the adaptor, plug and cable with wet hands. 8. Unplug, stop recharging, and take out the battery before clean the unit. 9. Remove the battery before dispose the unit. 10. Unplug or turn off the unit before take out the battery. 11. Recycle the disused battery properly. 12. Keep battery away from inflammable area. 13. Do not soak the battery into water or raindrop. 14. Do not try to disassemble the battery. 15. Do not disregard kids playing with battery. 16. Do not contact eyes, skin, clothes with battery leaking fluid, wipe the leaking battery with dry cloth before recycle it properly. 23 Royal Robot 1300 ROYAL CONSUL EUROPE A/S Ringvejen 59, 7900 Nykøbing Mors-Danmark Tlf. +45 96 69 16 00 Fax. +45 96 69 16 01 E-mail: [email protected] Web: www.royal-consul.dk