Preview only show first 10 pages with watermark. For full document please download

Rpi-122 : Optical Sensors

   EMBED


Share

Transcript

External dimensions (Unit : mm) RPI-122 Photointerrupter, Ultraminiature type Cross-section B-B +0 4.4 -0.1 Absolute maximum ratings (Ta=25°C) Reverse voltage VR 5 V PD 80 mW Collector-emitter voltage VCEO 30 V Emitter-collector voltage VECO 4.5 V IC 30 mA Collector current Collector power dissipation Applications Optical control equipment Cameras Floppy disk drives 4-φ 0.8 Features 80 mW Topr −25 to +85 °C Storage temperature Tstg −40 to +100 °C 1) Ultra-small. 2) Minimal influence from stray light. 3) Low collector-emitter saturation voltage. Gap B A 0.8 Cross-section A-A 0.1 Symbol Min. Typ. Max. Unit VF − 1.3 1.6 V IF=50mA IR − − 10 µA VR=5V ICEO − − 0.5 µA VCE=10V λP − 800 − nm Collector current IC 0.18 − 1.08 mA VCE=0.7V, IF=3mA VCE(sat) − − 0.3 V IF=20mA, IC=0.3mA VCC=5V, IF=20mA, RL=100Ω Dark current Collector-emitter saturation voltage tr tf − 10 − µs Cut-off frequency fC − 1 − MHz Peak light emitting wavelength λP − 950 − nm Response time tr tf − 10 − µs Maximum sensitivity wavelength λP − 800 − nm (0.5) 2.3 Optical axis center − 4-0.5 B A 4-0.2 4-0.4 (2) (2.7) Collector Anode IF=50mA ∗ Non-coherent Infrared light emitting diode used. Notes: 1. Unspecified tolerance shall be ±0.2 . 2. Dimension in parenthesis are show for reference. VCC=5V, IC=1mA, RL=100Ω ∗ This product is not designed to be protected against electromagnetic wave. − Cathode Emitter 100 25 0.5 1.0 1.5 2.0 20 10 0 2.5 DISTANCE : d (mm) 75 50 25 1.5 2.0 2.5 DISTANCE : d (mm) Fig.4 Relative output current vs. distance ( ) POWER DISSIPATION / COLLECTOR POWER DISSIPATION : PD / Pc (mW) d 100 1.0 20 40 60 80 10 100 100 PD PC 80 60 40 20 −20 0 20 40 60 80 AMBIENT TEMPERATURE : Ta (°C) Fig.5 Power dissipation / collector power dissipation vs. ambient temperature 0.6 0.8 1.0 1.2 1.4 1.6 3 2 0 0 1.8 100 RL=100Ω 10 20 30 40 50 1 0.05 0.1 FORWARD CURRENT : IF (mA) Fig.7 Collector current vs. forward current Input 140 120 100 80 60 40 20 RL=500Ω 10 0 20 40 60 80 100 1 10 AMBIENT TEMPERATURE : Ta (°C) Fig.6 Relative output vs. ambient temperature 1 VCC Input Output 90% RL 30mA 10% Output td 20mA tr 2 4 6 8 10 COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig.10 Output characteristics 25 50 75 Fig.9 Dark current vs. ambient temperature 40mA 10mA 0 Fig.8 Response time vs. collector current IF=50mA 10 −25 AMBIENT TEMPERATURE : Ta (°C) 20 0 0 VCE=30V VCE=20V VCE=10V 10 COLLECTOR CURRENT : Ic (mA) tf td : Delay time t r : Rise time (time for output current to rise from −40 −20 100 0.1 160 0 RL=1kΩ 1 Fig.3 Forward current vs. forward voltage 120 0 0.4 4 FORWARD VOLTAGE : VF (V) Fig.2 Forward current falloff 125 0.5 0 75°C 20 AMBIENT TEMPERATURE : Ta (°C) Fig.1 Relative output current vs. distance ( ) 0 0 −20 50°C 30 0 0.2 RELATIVE COLLECTOR CURRENT : Ic (%) 0 0 30 25°C DARK CURRENT : ID (nA) 50 0°C 40 1000 5 RESPONSE TIME : t (µs) 75 40 −25°C COLLECTOR CURRENT : Ic (mA) d 50 50 COLLECTOR CURRENT : Ic (mA) 100 FORWARD CURRENT : IF (mA) 125 FORWARD CURRENT : IF (mA) RELATIVE COLLECTOR CURRENT : Ic (%) Electrical and optical characteristics curves RELATIVE COLLECTOR CURRENT : Ic (%) Photo transistor Infrared light emitter diode Response time 2.5± 0.5 Output Input charac- characteristics teristics Peak sensitivity wavelength Reverse current 0.4 +0.15 -0.1 Conditions Forward voltage Transfer characteristics Parameter 3.3 Electrical and optical characteristics (Ta=25°C) 2.8± 0.1 1 PC Operating temperature C 0. 7 Input(LED) Output Power dissipation 1.5 2 mA 2.7 Through hole 0.9± 0.1 Unit 50 3.4 Limits IF 2.6± 0.1 Symbol Forward current Parameter (phototransistor ) 1.3 +0.05 -0.2 7 0. C 3.6± 0.1 0.25 10% to 90% of peak current) t f : Fall time (time for output current to fall from 90% to 10% of peak current) Fig.11 Response time measurement circuit 100 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1