Transcript
6. ANTI HI-JACK MODE There are three different ways to activate Anti Hi-Jack (AHJ). 1. By Ignition (Programmable Feature #7, Default setting is OFF) When Programmable Feature #7 is ON, and the ignition is turned on, the alarm will enter AHJ mode. The siren will chirp three times and the LED will flash fast. Note: If programmable feature #7 hi-jack through ignition is enabled (ON) you must exit hi-jack mode using the valet button before entering programming mode, see section 4 to enter programming mode. Do not turn ignition off, leave ignition on, then press valet button 5 times to enter programming mode. 2. By Door (Programmable Feature #8, Default setting is OFF) When Programmable Feature #8 is ON, and when the Ignition is ON AND the driver door is opened then closed, alarm will enter AHJ mode. The siren will chirp three times and the LED will flash fast. 3. By Remote Control (Programmable Feature #9, Default setting is OFF) When Programmable Feature #9 is ON and Ignition ON, Press and hold PANIC and AUX together for 2 seconds – alarm will enter AHJ mode. Siren will chirp three times and LED will flash fast. NOTE: All three features can be set to ON. ANTI HI-JACK MODE ACTIVATED STATUS • From 0-60 sec LED will flash quickly. • From 61-70 sec LED will flash quickly, siren chirps, and the parking light will flash. • From 71-80 sec LED will flash quickly, siren chirps, parking light will flash, and ignition cut output constantly. • After 81 sec LED will flash quickly, siren chirps, parking light will flash and ignition cut output constantly. EXIT ANTI HI-JACK MODE • From 00-60 sec, Turn on the ignition, then press and hold UNLOCK button for 2 sec. The system will be in disarm mode. • After 60 sec, Turn on ignition, then press override switch for 1 sec. The system will be in disarm mode.
Manual REMOTE OPERATION GUIDE #RRAL900-433 INSTALLATION #RRAL900-433 REMOTE OPERATION #RRAL900-433 GUIDE #RRAL900-433 REMOTE OPERATION GUIDE OPERATION GUIDE #RRAL900-433 REMOTE OPERATION GUIDE #RRAL900-433 REMOTE LOCK BUTTON LOCK BUTTON LOCK BUTTON
• Press and release the LOCK button to ARM ALARM and LOCK DOORS • Press and release the LOCK button to ARM ALARM •• and Press and LOCKALARM DOORS LOCK DOORSthe Press and release release the LOCK LOCK button button to to ARM •• and Press and button and to press it again for LOCK DOORSLOCK Press and release release the LOCK button LOCK DOORS 2 SECONDS to BYBASS SHOCK SENSOR and ARM the LOCK button ARM LOCK DOORS • Press and release LOCK button and to press it ALARM again for ALARM (Use this to bypass shock sensor) and LOCK DOORS SECONDS to BYBASS SHOCK SENSOR ARM •• 2 Press and LOCK button and press it and again for Press and release release the LOCK button to ARM ALARM ALARM (Use this tothe bypass shock sensor) • 2 Press and release LOCK button to LOCKand DOORS SECONDS to BYBASS SHOCK SENSOR ARM and LOCK DOORS (Use this toLOCK bypass shock sensor) •• ALARM Press release button and press it again for Press and and release the LOCK button to LOCK DOORS 2Press SECONDS to BYBASS SHOCK SENSOR ARM and release release LOCK button button and press itand again for •• Press and the UNLOCK to DISARM ALARM (UseUNLOCK this to bypass shock sensor) 2 SECONDS to BYBASS SHOCK SENSOR and ARM ALARM and DOORS • Press and release thebypass UNLOCK button to DISARM ALARM (Use this to shock sensor) •• ALARM Press and release the UNLOCK button to STOP and UNLOCK DOORS button to DISARM Press and release the UNLOCK ALARM TRIGGER and UNLOCK DOORS button to STOP • ALARM Press and release the UNLOCK •• ALARM Press and release the UNLOCK TRIGGER Press and release the UNLOCK button button to to UNLOCK DISARM STOP DOOR TRIGGER ALARM and UNLOCK DOORS •• Press Press and and release release the the UNLOCK UNLOCK button button to to UNLOCK DISARM •• DOOR Press and Hold the UNLOCK button for 2 SECONDS Press and release the UNLOCK UNLOCK ALARM and UNLOCK DOORS button to STOP to switchTRIGGER ALARM to KEYLESS basic mode. ALARM DOOR •• Press and Hold thethe UNLOCK button for to 2 SECONDS release UNLOCK button STOP to switch ALARM tothe KEYLESS basic mode. • Press and release UNLOCK button to2 UNLOCK Press and Hold the UNLOCK button for SECONDS ALARM TRIGGER LOCK to switch ALARM KEYLESS basic mode. • DOOR Press and releasetothe UNLOCK button to UNLOCK LOCK PRESS • Press and Hold the UNLOCK button for 2 SECONDS DOORand TOGETHER • LOCK • Press hold the PANIC butswitch ALARM to KEYLESS basic mode. • to Press and Hold the UNLOCK button for 2 SECONDS PRESS
LOCK BUTTON LOCK BUTTON
UNLOCK BUTTON UNLOCK BUTTON UNLOCK BUTTON
UNLOCK BUTTON UNLOCK BUTTON
PANIC BUTTON PANIC BUTTON BUTTON tonPANIC for 2 SECONDS to TRIGGER
• Press and ALARM hold the to PANIC but- basic mode. to switch KEYLESS HORN / SIREN for and 2 SECONDS to TRIGGER • ton Press hold the PANIC butPANIC BUTTON HORN ton for 2/ SIREN SECONDS to TRIGGER PANIC BUTTON / SIREN • HORN Press and hold the PANIC butAUX BUTTON for 2and SECONDS to TRIGGER •ton Press hold the PANIC butHORN for /and 2SIREN SECONDS to TRIGGER AUX BUTTON • ton Press release the AUX button for TRUNK HORN / SIREN AUX BUTTON RELEASE
TOGETHER
PRESS LOCK PANIC TOGETHER
LOCK PANIC PRESS
TOGETHER PANIC PRESS TOGETHER
PANIC
Ignition must be OFF
Ignition must be OFF During IgnitionValet must Mode be OFF Ignition must Mode be OFF During Valet Ignition must Mode be OFF During Valet Ignition Ignition must must be be OFF OFF During Valet Mode Ignition must Mode be OFF During Valet
Ignition must OFF and Alarm must bebe ARMED Ignition OFF Alarm must be ARMED and When siren / horn is Sounding Ignition OFF Alarm must be ARMED and
Ignition OFF When siren / horn is Sounding During Driving or Valet Mode Alarm must ARMED and When siren /be horn is Sounding Ignition OFF During Driving Valet Mode Alarm must beor ARMED and Alarm must be DISARMED When siren / horn is Sounding During Driving or Valet Mode Ignition OFF and Ignition ON. Alarm DISARMED When must siren be / horn is Sounding and Ignition During Driving or Valet Mode Alarm must beON. DISARMED and Ignition During DrivingON. or Valet Mode Alarm must be DISARMED Press LOCK and PANIC buttons and Ignition Alarm must beON. DISARMED
2nd AUXILIARY 2nd AUXILIARY 2nd AUXILIARY 2nd togetherAUX to get AUX2 Output.
• Press andON. PANIC buttons andLOCK Ignition Note: Contact installer to make sure this
together to get AUX2 Output. • option Press LOCK and PANIC buttons 2nd AUXILIARY is enabled. Note: Contactto installer to make Output. sure this together get AUX2 2nd AUXILIARY option is enabled. Contact installer make surebuttons this • Note: Press LOCK andto PANIC
to getand AUX2 Output. • together Press LOCK PANIC buttons Note: Contact to installer to make sure this together get AUX2 Output.
PANIC
option is enabled.
option is enabled. Note: Contact installer to make sure this
• Press and release the AUX button for TRUNK option is enabled. •• Press and thethe AUX button for for 2 SECONDS Alarm must be DISARMED RELEASE Press and hold release AUX button TRUNK for SILENT ARMING and Lock Doors and ignition OFF RELEASE • Press and hold the AUX button for 2 SECONDS for Alarm must be DISARMED •• Press and hold AUX button for 2 Alarm must ARMED and SILENT ARMING Lock Doors and ignition Press and release the AUX button TRUNK for hold the theand AUX button for for 2 SECONDS SECONDS for Alarm must be beOFF DISARMED SILENT ARMING DISARMING and Unlock Doors ignition OFF RELEASE SILENT Lock Doors and ignition •• Press theand AUX button for 2forSECONDS Alarm must beOFF ARMED and Press and and hold release the AUX button TRUNK for SILENT DISARMING andbutton Unlock ignition OFF • Press and hold the AUX forDoors 2 SECONDS for Alarm must be ARMED DISARMED and RELEASE ARMING and Lock Doors and ignition DISARMING and Unlock ignition OFF • SILENT Press and hold the AUX button forDoors 2 SECONDS for Alarm must beOFF DISARMED • Press and hold theand AUX button for 2 SECONDS for Alarm beOFF ARMED and SILENT ARMING Lock Doors and must ignition USED FOR: 1. Stopping horn/siren: Turnthe ignition on, pressfor and valet switch stops. DISARMING and Unlock Doors ignition OFF • SILENT Press and hold AUX button 2 hold SECONDS for until horn/siren Alarm must be ARMED and 2. To enter/exit keyless basic mode (LED steady on): Ignition on and hold valet switch for 5 SILENT DISARMING and Doors ignitionstops. OFF seconds. USED FOR: 3. 1. Stopping horn/siren: Turn ignition on,Unlock press and hold valet switch until horn/siren Use to program remotes: Turn ignition on, press and release valet switch 5 times, press lock buttons on To enter/exit keyless Turn basicignition mode (LED steady on): Ignition on anduntil holdhorn/siren valet switch for 5 seconds. USED FOR: 2. 1. each Stopping horn/siren: on, press and hold valet switch stops. remote to be programmed, turn ignition off. Up to 4 remotes may be programmed. 3. Useenter/exit to program remotes: ignition press and release switch 5 times, buttons on 2. To keyless basicTurn mode (LED on, steady on): Ignition onvalet and hold valet switchpress for 5lock seconds. Most Common Locations (Ask where itignition isturn located.) each remote to installer be programmed, ignition off. and Up to 4 remotes may be 5programmed. 3. Use to program remotes: Turn on, press release valet switch times, press USED FOR:glove 1. Stopping horn/siren: Turn ignition on,behind press the and hold valet switch until horn/siren stops. lock buttons on • Inside compartment, driver's kick panel, each remote to be programmed, turn ignition off. Up to 4 remotes may be programmed. Most Common Locations (Ask installer where it is located.) 2. enter/exit keyless basic mode (LED steady on): Ignition and until hold horn/siren valet switch for 5 seconds. USED 1.To Stopping horn/siren: Turn ignition on, press and hold valet on switch stops. fuseFOR: panel access door, underneath • Inside glove driver's kick panel, behind the on): 3. to front program remotes: Turn on, press andIgnition releaseonvalet 5 times, press buttons on Most Locations (Ask installer where itignition is(LED located.) 2. Use Tocompartment, enter/exit basic mode steady and switch hold valet switch for 5lock seconds. theCommon dashboard in ofkeyless the driver. panel access door, to underneath remote be programmed, turnbehind ignition off. Up 4 remotes be 5 programmed. • fuse Inside glove compartment, driver's kick panel, the 3. each Use to program remotes: Turn ignition on, press andtorelease valetmay switch times, press lock buttons on the dashboard in front of the driver. fuse panel access door, underneath REPLACEMENT REMOTE PART NUMBER: each remote to installer be programmed, ignition off. Up#REMOTE-RRAL900-433 to 4 remotes may be programmed. Most Common Locations (Ask where it isturn located.) THIS IS ONLY dashboard in front of the driver.kick panel, • the Inside glove compartment, driver's behind the A GUIDE
AUX BUTTON AUX BUTTON
VALET OVERRIDE SWITCH OPERATION VALET OVERRIDE SWITCH OPERATION VALET OVERRIDE SWITCH OPERATION
VALET OVERRIDE SWITCH OPERATION VALET OVERRIDE SWITCH OPERATION
REPLACEMENT REMOTE PART NUMBER: #REMOTE-RRAL900-433 Most Common Locations (Ask installer where it is located.) The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
panel access door, underneath THIS IS •fuse Inside glove compartment, driver's panel, behind theA GUIDE REPLACEMENT REMOTE PART #REMOTE-RRAL900-433 ©2011kick Micro Alarm Systems, Inc.ONLY •NUMBER: RRAL900-433-REMOTE-NOV2011.indd the in front of theare driver. The button operations shown a general guide. Consult with dealer that installed your keyless entry to confirm these remote functions. fusedashboard panel access door, underneath THIS IStheONLY A GUIDE ©2011 Micro Alarm Systems, Inc. • RRAL900-433-REMOTE-NOV2011.indd the dashboard in front shown of thearedriver. The button operations a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions.
REPLACEMENT REMOTE PART NUMBER: #REMOTE-RRAL900-433 ©2011 Micro Alarm Systems, Inc. • RRAL900-433-REMOTE-NOV2011.indd
THIS IS ONLY A GUIDE
REPLACEMENT REMOTE PART NUMBER: #REMOTE-RRAL900-433
The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions. THIS IS ONLY A GUIDE ©2011 Micro Alarm Systems, Inc. • RRAL900-433-REMOTE-NOV2011.indd The button operations shown are a general guide. Consult with the dealer that installed your keyless entry to confirm these remote functions. ©2011 Micro Alarm Systems, Inc. • RRAL900-433-REMOTE-NOV2011.indd
REPLACEMENT REMOTE PART NUMBER: #REMOTE-RRAL900-433
THIS IS ONLY A GUIDE These instructions are a general guideline of possible applications. Specifications may change dependent upon vehicle. Always review the vehicle’s service manual and wiring diagram when performing an installation. Manufacturer does not assume any responsibility for damages to property or persons which may occur due to incorrect applications or product failure. Not responsible for typographical errors. Specifications are subject to change without notice.
8
Warranty void if not installed by authorized dealer. Specification and date are subject to change or withdrawal without notice. © 2011 Micro Alarm, Inc. • rral900-433-Inst-NOV2011.indd
1. HOW TO “CODE LEARN” A REMOTE CONTROL:
5. RRAL900-433 ADDITIONAL INFORMATION
When Car Alarm is Disarmed and Ignition is off:
AUXILIARY ONE (Grey Wire) maybe used for either Trunk Release (default) or Remote Starter. (Programmable feature #3)
1. Turn Ignition To ON Position. 2. Press Valet Override Switch 5 Times. Siren / Horn will Chirp Once and Parking Light and LED will stay ON. 3. Press LOCK on each remote to be programmed. Siren / Horn will chirp and parking light will flash to confirm remote has been programmed. 4. Turn Ignition OFF.
Press and relase AUX button to release trunk OR engage Remote Starter. • If Gray Wire is used for Trunk Release: the system will disarm and unlock vehicle • If Gray wire is connected to enable Remote Starter, the system will bypass sensor and ignition • Programmable feature #3 must be programmed to either Trunk Release (default) or Remote Starter.
Note 1: After 10 seconds without any programming activity, or if the ignition is turned OFF, the System will automatically exit Remote Control Programming Mode. Note 2: Up 4 Remote Controls can be programmed.
SECOND AUXILIARY or HORN OUTPUT (Brown/White Wire) has four programmable options (programmable feature #4):
2. JUMPER PIN AND WIRING CONFIGURATION
JP1 JP2 JP3 JP4
REPLACEMENT REMOTE PART#: REMOTE-RRAL900-433
#RRAL900-433
JP1 - OPEN = Last Door Arm/Auto Rearm = OFF CLOSED = Last Door Arm/Auto Rearm = ON JP2 - OPEN = Last Door Arm/Auto Rearm w/o Door Lock CLOSED = Last Door Arm/Auto Rearm w/ Door Lock JP3 - OPEN = Door Light Delay for 60 Sec = ON CLOSED = Door Light Delay for 60 Sec = OFF JP4 - OPEN = CDL Pulse Timer = 3.5 Sec CLOSED = CDL Pulse Timer = 0.5 Sec NOTE: DEFAULT FOR ALL JPS IS CLOSED
1. PULSE – Provides a negative output as long as “Lock” and “Panic” are pressed and held together. (Default) 2. LATCH OUTPUT – Provides a negative output for 25 seconds when “Lock” and “Panic” buttons are pressed together at the same time and released. 3. HORN – Horn and siren work together only on all alarm events. Siren will work on all events. 4. LIMITED HORN – Horn enables when alarm is triggered. Horn does not activate when lock/unlock is pressed on the remote, only the siren chirps.
RRAL900-433 BRAINSTIC
SHOCK SENSOR (WHITE CONNECTOR) DOOR LOCK (RED CONNECTOR) LED (WHITE CONNECTOR)
VALET SWITCH (BLUE CONNECTOR)
16 - N/A 15 - BLACK/WHITE WIRE (–) Dome Light Output 14 - N/A 13 - BROWN/WHITE WIRE (–) 2nd AUX / Horn 12 - BLUE WIRE (–) Hood Pin Input 11 - ORANGE WIRE (–) Starter Disable 10 - PURPLE WIRE (+) Door Trigger Input 9 - N/A 8 - GREEN WIRE (–) Door Trigger Input 7 - GREY WIRE (–) Trunk Release Output (Aux) 6 - YELLOW WIRE (+) Ignition Input 5 - BROWN WIRE (+) Siren Output (3 Amp) 4 - BLACK WIRE (–) Ground 3 - WHITE WIRE (+/–) Parking Light Output 2 - RED WIRE (+) 12 Volts 1 - RED/WHITE WIRE (+/–) Parking Light Input
2 5.3cm
16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
6cm
NOTE: Programmable feature #4 must be programmed to how the Brown/White wire is connected and intended to be used. ONLY ONE OPTION MAY BE SELECTED AND PROGRAMMED.
AUXILIARY 2:
LOCK
IF LATCH IS WIRED / CONFIGURED: Press and Release “Lock” and “Panic” at same time to get a negative output for 25 seconds
Press TOGETHER
PANIC
7
IF PULSE IS WIRED / CONFIGURED (Default): A negative output will be provided by pressing and holding “Lock” and “Panic” at the same time. Output will be provided as long as “Lock” and “Panic” are held.
2A. JUMPER PIN INFORMATION
4.A PROGRAMMABLE FEATURE TABLE FEATURES
LOCK: Siren chirp once LED flash once
1
Lock / Unlock Pulse
Single*
Double
1 Short Chirp
2
Disarm Parking Light O/P
Flash Twice*
Light 30 sec
1 Short Chirp
3
Disarm (1st AUX)
Trunk*
Car Start (see Note 1)
1 Short Chirp
4
2nd AUX / Horn
5
IGN Lock / Unlock
On*
Off
1 Short Chirp
6
Keyless Entry
Off*
On
1 Short Chirp
7
IGN Anti Hi-Jack
Off*
On Note 6
1 Short Chirp
8
Door Anit Hi-Jack
Off*
On
1 Short Chirp
9
Remote Anit Hi-Jack
Off*
On
1 Short Chirp
10
UNLOCK: PANIC: AUX: Siren Siren chirp Siren chirp Siren chirp Chirp twice 3 times 4 times Indicator LED flash LED flash 3 LED flash 4 twice times times
Pulse* Latch Horn Limited Horn (see Note 2) (see Note 3) (see Note 4) (see Note 5)
Back to Press AUX for 3 seconds. Siren will chirp 6 times. Factory Default Light will flash 6 times. All features will be returned to default settings.
1 Short Chirp
1 Short Chirp
*All settings shaded in gray are factory default settings. Note 1: CAR START – Press and release AUX button to get a 0.5 second negative output on the 1st channel (trunk release wire). This will bypass the sensor and ignition. Note 2: PULSE – Press and hold the LOCK and PANIC buttons, and the 2nd Channel Output will send signal as long as the LOCK and PANIC buttons are held. Note 3: LATCH – Press LOCK and PANIC buttons for a 30 second signal output. Note 4: HORN – The Horn wire will have an output whenever the Siren wire has an output. Note 5: Limited Horn – The Horn will sound only during Door Trigger, Ignition, or when the Shock Sensor is triggered. The siren will sound/chirp on all events. Note 6: If ignition hi-jack is enabled, you must disable hi-jack using the valet button befor entering programming mode. Leave ignition on after turning off hi-jack. See ignition hi-jack on page 8.
4.B LED INDICATION TABLE Type of Trigger in Armed Mode
LED Status
No Trigger
LED Flash rapidly (Auto Rearm Activated)
Ignition
1 Flash & 1 Pause
Pin Switch Zone
2 Flash & 1 Pause
Door Zone
3 Flash & 1 Pause
Sensor Zone
4 Flash & 1 Pause
6
Jumper 1 OPEN – Last Door Arm/Auto Rearm = OFF CLOSE – Last Door Arm/Auto Rearm = ON Jumper 2 OPEN – Last Door Arm/Auto Rearm without Door Lock CLOSE – Last Door Arm/Auto Rearm with Door Lock Jumper 3 OPEN – Dome Light Delay for 60sec = ON CLOSE – Dome Light Delay for 60sec = OFF Jumper 4 OPEN – Central Door Lock (CDL) Pulse Timer = 3.5sec CLOSE – Central Door Lock (CDL) Pulse Timer = 0.5sec Default setting for all jumpers is CLOSED.
2.B POWER HARNESS WIRING CONFIGURATION Pin#1: RED/WHITE = PARKING LIGHT INPUT VOLTAGE (+/–) • This Input will provide the Voltage and Polarity to White Wire, fused at 10 Amps. Pin#2: RED = MAIN POWER CONNECTION, 12V (+) • Connect to the (+)12V Battery Terminal, Fused at 15 Amps. Pin #3: WHITE = PARKING LIGHT OUTPUT (+/–) • Connect this Wire to the Vehicle 12 Volts Parking Light Circuit. • This Output will provide a Flashing 12 Volts fused at 10 Amps to energize vehicle’s Parking Light. Pin #4: BLACK = GROUND (–) • Connect this wire to Chassis ground. Pin #5: BROWN = SIREN OUTPUT (+) • This wire will provide a (+)12Volts positive Output for powering a Siren(3A). Pin #6: YELLOW = IGNITION INPUT (+) • Connect to the Vehicle (+)12 Volt Ignition Wire Pin #7: GRAY = AUXILIARY/TRUNK RELEASE OUTPUT, 500mA (–) • This wire will provide a 12V. Negative output. • May be used for remote starter, see programmable feature #3. 3
2.B POWER HARNESS WIRING CONFIGURATION CONTINUED Pin #8: GREEN = Negative Trigger Door Input (–) • This Input will trigger the Alarm if it becomes Grounded while alarm is armed (if door is opened). Pin #9: N/A Pin #10: PURPLE = Positive Trigger Door Input (+) • This Input will trigger the Alarm if it receive +12 Volts while alarm is armed (if door is opened). Pin #11: ORANGE = Starter Kill Output (–) • This output needs to be used with a relay to be cut into the vehicle starter wire. Pin #12: BLUE = Hood Pin Input (–) • This Input will trigger the Alarm if it becomes Grounded while alarm is armed (if the hood is opened). Pin #13: BROWN/WHITE = 2nd Auxiliary or horn honk output. Note: Controlled through programmable feature #4. Pin #14: N/A Pin #15: BLACK/WHITE = Dome Light Supervision (–) • This wire will provide a 0-60 sec for illuminated vehicle when Alarm is Disarmed.
2.D 2 PIN HARNESS(LOCK/UNLOCK) WIRING CONFIGURATION GREEN:(-) Connect this Wire to Vehicle Lock Wire. BLUE: (-) Connect this Wire to Vehicle Unlock Wire. Note: For vacuum operated door lock system remove jumper pin #4. Use Optional Part RRAL-DL to add door lock on-board relay interface.
3. VALET OVERRIDE SWITCH OPERATION The Valet switch has five functions: • To Program Remote Controls (see Section 1 – How to “Code Learn” a Remote Control) • To Program the “Programmable Features” (see Section 4 – Programmable Features) • Basic Keyless Entry Mode • With Ignition ON, hold Valet switch for 5 seconds (repeat to exit). • Only locks and unlocks doors; Horn and siren only work in “Panic Mode”. LED steady on. • NOTE: This is different from Programmable Feature #6, which does Keyless Entry where all features work except door, hood, and shock sensor triggers. • To Stop Panic Mode if Remote is Lost or Not Present • With Ignition ON, hold Valet switch until Horn/Siren stops.
Pin #16: N/A
• To Exit from Hi-jack mode • Turn on ignition, then press override switch for 1 sec. The system will be in disarm mode.
2.C SHOCK SENSOR
4. PROGRAMMABLE FEATURES
Adjust Sensitivity for best protection.
To change any of the programmable features, please follow these steps.
1. If car receives light Impact, siren / horn will chirp 5 times in quick succession and Parking Light will Flash once for warning purpose. 2. If car receives heavy impact, siren / horn will sound and Parking Lights will Flash for 60 sec. NOTE: Shock Sensor will sound maximum of 5 times, then will reset to deactive until armed again.
4
1. Turn ignition ON. 2. Press Valet Override switch 5 times – the siren / horn will chirp once and parking light and LED will stay on. 3. Press the Valet switch the number of times equal to the number of the feature to be programmed 4. Press the button to be programmed (LOCK, UNLOCK, PANIC, AUX) on the remote to choose the setting you desire. 5. Turn ignition OFF. Note: If 10 seconds expire without any programming activity, the parking light and LED will turn OFF, and the System will return to Disarm mode. 5
