Rs1sx Manual 180x126 Corelx2 20150331 Editable.cdr

Transcript

RS1 S X V 1.0 Quick start Quick start Charge Charge the camera for three hours or until the blue light turns off. Introduction Mount Welcome to our most straightforward body camera. For your convenience, the camera is set up and ready to go in three easy steps. Choose how to mount your camera; you can use either the Klickfast attachment, clips or a lanyard. Record Slide the red switch down to start recording. To stop recording, slide the red switch up. RS1 - SX Quick Start and User Manual 2 RS1 - SX Quick Start and User Manual 3 Quick start Quick start Charge Mount Open the cover on the bottom of the camera. Choose your mount: • Klickfast stud • Shirt clip (adjustable for male and female shirts) • Pocket clip (for use with lanyard) Insert the mini USB into the port and connect to a computer or plug in to charge. Slot clip into place, ensuring the 2 plates on the clip are between the 3 plates on the back of the camera, and align the holes. NOTE: This is the same cable that will upload video to a computer. RS1 - SX Quick Start and User Manual 4 Place the screw through the top hole, into the clip, and tighten at the desired angle with supplied screwdriver. RS1 - SX Quick Start and User Manual 5 Quick start Operation Record Pull down the red switch to record. Camera articulation As confirmation: The camera head rotates 110° vertically. • The camera will beep three times. • The LED and the recording icon on the screen will flash red. Pull the switch back up to stop recording. As confirmation: • The camera will beep twice. Camera rotation • The lights will stop flashing and the camera will turn off. To set the RS1-SX to sit correctly against the body, fasten to the desired angle by tightening the screw at the top of the camera. RS1 - SX Quick Start and User Manual 6 RS1 - SX Quick Start and User Manual 7 Operation Operation Charging via USB (off when charged) Recording (flashing) On when connected to PC (via USB) Flashing record indicator Time HH:MM:SS 2015-01-27 14:52:10 508MB RS1 - SX Quick Start and User Manual Date YYYY-MM-DD Micro SD card space remaining 8 Micro SD card (up to 32Gb) NOTE: Recordings will stop automatically when the card is full. RS1 - SX Quick Start and User Manual 9 Editing settings options Editing settings options 4. This will launch the first of two screens. Follow the instructions on these screens. 1. Connect RS1 - SX to your computer’s USB port and turn on the camera. 1. Select the RS1 - SX camera you want to change settings on. 2. While still connected to the PC, turn off RS1 - SX then turn it on again. 2. Navigate to the RS1-SX removable disk drive on your computer. 3. Double click on the drive and you will see the following RS1 utility icon. Double click on this to start the setup procedure. RS1 - SX (J:) RS1 Utility RS1 Utility RS1 Setup 0.97 GB free of 3.62 GB i RS1 Setup Once you have clicked the button below you will need to turn off your RS1 then turn it on again i Please turn your RS1 off then on again while still connected to this computer Select RS1 Select RS1 RS1B1234 RS1B1234 Click to edit RS1 settings WAITING TO FIND RS1 RS1 Utility.exe RS1 - SX Quick Start and User Manual 10 RS1 - SX Quick Start and User Manual 11 Editing settings options Editing settings options Once you have rebooted the RS1 - SX, you will see the following setup utility. Please enter the default password. The default password is “admin”. The following settings can be changed by running the RS1 - SX setup utility: RS1 Utility Date and time: this takes the time from your PC (ensure your PC’s clock is accurate). Utility password: the default password is “admin”. RS1 setup LCD screen off time: to conserve battery power, the screen can be set to automatically switch off after the time set in this option. Sync Date/Time Sync Date/Time Syncronise RS1 to your PC’s Date & Time Password Change Password Split video: this setting will ensure that long recordings are split into sections according to the length specified. New Password ConfirmPassword Machine ID: the unit has been assigned a unique number during production that you may wish to change. This sets the unit ID for the camera. The machine ID must start with RS1B. Parameters Playback Disable Enable Show Portrait Change Parameters Screen Off Split Video 1 min 30min Machine ID ( 9 Alphanumerics ) Enable/disable playback. RS1B1234 NOTE: You must click “Change Parameters” before exiting. Exit RS1 - SX Quick Start and User Manual 12 RS1 - SX Quick Start and User Manual 13 Mounting and usage options Mounting and usage options Klickfast Attach the Klickfast to use with a Klickfast dock. Harness For use with loose fitting clothes or uniforms. (optional extra) Shirt clip For use on a shirt (ajustable for male and female shirts). Table top Pocket clip For use in interviews and other static situations. For use with a lanyard around the neck or attached to a pocket. RS1 - SX Quick Start and User Manual 14 RS1 - SX Quick Start and User Manual 15