Transcript
Owner’s Manual for the CCI-0008
RS232 Serial Option Module for NuVAX
CCI-0008-OM Revision A
Owner's Manual for the
CCICCI-0008
Serial Option Module for NuVAX
Document Number CCI-0008-OM Revision A, February 2008
VMS is a trademark of Hewlett Packard Corporation.
The material in this manual is for informational purposes only and is subject to change without notice.
Contents
1
Installation......................................................................................................... 1 1. Open the system enclosure........................................................................................ 1 2. Install the CCI-0008 module..................................................................................... 2 3. Install the octopus cable............................................................................................ 3 4. Close the system enclosure ....................................................................................... 3 5. Verify installation ..................................................................................................... 3
2
General Description.......................................................................................... 5 Specifications........................................................................................................................ 6
Appendix A - PCI Local Bus Interface Connector Pin Assignments ................... 9
Illustrations Figure 1-1: Inserting the Board into the Option Slot ............................................................... 2 Figure 2-1: DB25 Male Connector .......................................................................................... 6 Tables Table 2-1: User Interface Signals............................................................................................. 6 Table A-1: PCI Interface Connector Pin Assignments ............................................................ 9
i
Contents
ii
1 Installation
This chapter lists the steps involved in installing the CCI-0008 hardware. 1.
Open the system enclosure
To open the NuVAX system enclosure: A. If the system is running, shut down the system software as described in the system manual. B. Remove power to the system unit. C. Open the enclosure by removing two thumb screws and sliding the cover towards the rear and lifting. Replace the two thumb screws into the chassis rear panel. D. Remove the PCI card retainer rail by first lifting the black release knob and then lifting the rail up and out.
Note: Use the anti-static wrist strap supplied with your system unit to prevent damage to the equipment. Clip the free end of the strap to the metal frame of the enclosure.
1
Installation
2.
Install the CCI-0008 module
The CCI-0008 is installed in slot 6, the PCI slot furthest away from the bus adapter. A. If the back of the system unit has a metal cover plate over the opening of slot 6, remove the anchor screw that holds the cover in place then slide the cover out of the slot. Retain the anchor screw. B. Position the CCI-0008 with the high density connector toward the slot opening. Gently rock the module into the PCI connector while you fit the metal bulkhead into the slot opening. Be sure that the connectors are firmly seated. Note: If the enclosure contains RFI clips along the slot, take care when inserting the module not to push the clips out of alignment. C. Dress any cable away from the PCI slot. D. Secure the CCI-0008 using the anchor screw that you removed in Step A. Retain the cover plate for future use.
Figure 1-1: Inserting the Board into the Option Slot D. Remove the anti-static wrist strap, replace the cover on the enclosure and secure. You are now ready to connect the user equipment.
2
Installation
3.
Install the octopus cable
Use the supplied octopus cable to connect serial devices to the CCI-0008 controller.
4.
Close the system enclosure
Replace the PCI card retainer rail and the system cover. 5.
Verify installation
Digital Equipment diagnostics are not available for the CCI-0008. Using VMS login and applications is the only method to verify individual serial port operation.
3
Installation
4
2 General Description
The CCI-0008 is a serial asynchronous controller that supports eight full duplex channels with simultaneous transfer of data at a transmission speed of 38.4Kbps. Special features such as on-chip FIFO and flow control are used to prevent loss of data. The CCI-0008 is signal and pin compatible with Digital's serial controllers including the DHV11, DZQ11, DHQ11, and CXY08. The CCI-0008 is contained on a standard short PCI card. A 62-pin connector is used to connect an octopus cable to eight DB25 male connectors. Table 2-1 lists the user interface signals used by the CCI-0008 and Figure 2-1 depicts the connector layout.
5
General Description
Pin
Mnemonic
Description
2
TxD
Transmitted Data
3
RxD
Received Data
4
RTS
Request to Send
5
CTS
Clear to Send
6
DSR
Data Set Ready
7
GND
Ground
8
DCD
Carrier Detect
20
DTR
Data Terminal Ready
Table 2-1: User Interface Signals
Figure 2-1: DB25 Male Connector
Specifications Dimensions
Standard PCI short card measuring 4.72 x 3.27 inches (12.0 cm by 8.3 cm).
Interface Ports CCI-0008-A Controller CAB-0008-4 Cable
8 DB62 female connector 4-foot cable terminated with eight DB25 male
Electrical Power Required: +5 volts +3.3 volts
6
180 mA Not used
General Description
Operating Parameters Data bits Stop bits Parity Signals Speed
5,6,7,8 1, 1.5, 2 None, odd, even, space, mark RS232 – TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND 50 bps to 38.4K bps
Environmental Operating Conditions: Temperature Relative Humidity
5° to 50° C (41° to 122° F) 20% to 80% non-condensing
Storage Conditions: Temperature Relative Humidity
-40° to 66° C (-40° to 150° F) 10% to 95% non-condensing
7
General Description
8
Appendix A PCI Local Bus Interface Connector Pin Assignments
This appendix lists the pin assignments for the PCI bus interface. Pin
Signal
Pin
Signal
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30
TRST-L +12V TMS-H TDI-H +5V INTA-L INTC-L +5V
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30
-12V TCK-H GND TDO-H +5V +5V INTB-L INTD-L PRSNT1-L
+5V GND GND RST-L +5V GNT-L GND AD30-H +3.3V AD28-H AD26-H GND AD24-H IDSEL-H +3.3V AD22-H AD20-H GND
PRSNT2-L GND GND GND CLK-H GND REQ-L +5V AD31-H AD29-H GND AD27-H AD25-H +3.3V C/BE3-L AD23-H GND AD21-H AD19-H
Table A-1: PCI Interface Connector Pin Assignments
9
PCI Local Bus Interface Connector Pin Assignments
Pin
Signal
Pin
Signal
A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62
AD18-H AD16-H +3.3V FRAME-L GND TRDY-L GND STOP-L +3.3V SDONE-H SBO-L GND PAR-H AD15-H +3.3V AD13-H AD11-H GND AD09-H KEYWAY KEYWAY C/BE0-L +3.3V AD06-H AD04-H GND AD02-H AD00-H +5V REQ64-L +5V +5V
B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62
+3.3V AD17-H C/BE2-L GND IRDY-L +3.3V DEVSEL-L GND LOCK-L PERR-L +3.3V SERR-L +3.3V C/BE1-L AD14-H GND AD12-H AD10-H GND KEYWAY KEYWAY AD08-H AD07-H +3.3V AD05-H AD03-H GND AD01-H +5V ACK64-L +5V +5V
Table A-1: PCI Interface Connector Pin Assignments (cont’d
10
75 Gateway Blvd. Cottage Grove, Oregon 97424 USA http://www.logical-co.com
The Logical Company
Telephone: +1 541-942-3610 Fax: +1 541-942-3640 E-mail:
[email protected]
