REAR-VIEW INTEGRATION with HANDLE CAMERA FOR RAM 2009-2012 RVCCH-75R
CONNECTIONS OVERVIEW
work. Following these instructions from “Start” to” Finish” will ensure
Audio/Video AUX-INPUT
OPEN CLOSE
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
SEEK
RADIO MEDIA
(1) Tailgate Handle (1) Camera (CDR-02) (1) 19 ft. Extension (1) CH-75R Interface (1) CH-75R Harness (2585) (1) Instruction (1) Power Down Circuit
CONNECTION
FACTORY RADIO
SEEK
PARTS INCLUDED:
RAM 2009 - 2012
VOLUME
AUDIO
Audio/Video AUX-OUTPUT
COMPATIBLE WITH MYGIG STYLE RADIOS ONLY
SEEK
RADIO MEDIA VOLUME
22-PIN
(male plug)
(male plug)
WHITE / 12V REVERSE OUTPUT
MAKE SURE TO TEST THE CAMERA ANGLE BEFORE RE-INSTALLING THE TAILGATE COVER.
ON 1
YELLOW RCA / VIDEO SIGNAL
CONNECTION
2
3
4
5
6
CAN-BUS INTERFACE
RED / PARKING 12V LINE POWER
AUDIO
15 FT . EXTENTION
AUX-OUTPUT CONNECTION
VIDEO-IN
SWITCHING SOURCES RED BARREL
/
12V CAM POWER The parking lines are there to assist you while reversing. What the lines mean: BLACK / Green Line: CLEARGROUND Yellow Line: GETTING CLOSE Red Line: WARNING - VERY CLOSE
In order to toggle between the source inputs, the user must use the VES button on the radio screen
HDD DISC AUX
Preliminary:
To remove the parking lines simply connect the white wires located near the 4 pin tail connector of the camera .
(male plug)
2. Remove (2) 8mm screws to release the factory handle. 22-PIN 3. Swap the key cylinder from the OE tailgate to the new one.(female plug) 4. Fish the wires through the tailgate and into the bottom of the truck’s frame. Route towards the front of the vehicle. Test camera. 5. Remove the factory radio to gain access to the factory connectors. 6. Route the wires towards the radio and make the power and22-PIN video (female plug) connections. For powering up the camera, use the 12v REVERSE 8-PIN out from the 8-pin Molex connector. TRIGGER (White Wire) output coming (male plug)
SETTING THE DIP SWITCHES Dip Switches: To enable the features place the switch to the on position.
To access the VES button. press the RADIO/MEDIA button on the left side of the radio to see the VES option. The VES button is only active after the interface is installed.
GREEN
12V POWER
(INPUT) YELLOW
OPTIONAL / TOGGLE SWITCH NOT INCLUDED
RED
WHITE / 12V REVERSE OUTPUT
3:48 FUSE (NOT INCLUDED)
GREEN / 12V POWER SWITCH (SAME FUNCTION AS DIP 1) NON-PERMANEN T
ON 2
3
4
5
6
Dip 1: VIM Activation CAN-BUS INTERF ACE Dip 2. RVC Enable Dip 3. Not Used Dip 4. Not Used Dip 5 & 6: CAN-Termination (Default to OFF)
VES
RED / 12V CAM POWER
TO F ACTOR Y GRA Y WHITE HARNESS 1.22-PIN Remove (8) T30 hex screws to remove the tailgate cover. 22-PIN
1
FUSE (NOT INCLUDED)
GREEN / 12V POWER SWITCH (SAME FUNCTION AS DIP 1) NON-PERMANENT VIM
INSTALLING THE CAMERA AND CABLE
IMPORTANT: This interface will only work with NTSC video format. Compatible Nav Radio Type: MYGIG
OPTIONAL / TOGGLE SWITCH NOT INCLUDED
8-PIN
(male plug)
PleaseRADIO read the entire manual before installing this interface.
Up = ON Down = OFF
12V POWER (INPUT)
22-PIN
(male plug)
*Note: Incompatible in vehicles with Manual Transmission
RAM TAILGATE
(female plug)
TOOLS NEEDED:
Make sure to test the camera angle before re-installing the tailgate cover.
RED / 12V CAM POWER
HANDLE
MENU
- Hex ATIBLE ScrewWITH Set MYGIG COMP STYLE RADIOS - Phillips ScrewONL DriverY
RED BARREL / 12V CAM POWER
TO FACTORY HARNESS
22-PIN
22-PIN
AUX-INPUT
PRELIMINARY FACTOR Y:
RED / 12V POWER
BLACK / GROUND
(female plug)
- Remove the negative side of the battery to avoid any short circuits during the installation. - Do not install the interface near any major components or near the HVAC system. This may cause damage or overheating to the system.
(male plug)
19 FT . EXTENTION
VIDEO-IN/ CAMERA
PRECAUTIONS:
SEEK
YELLOW RCA / VIDEO SIGNAL
MENU
CONNECTION
- Lens Angle 170 Degrees - Resolution 420 TV Lines - Min. Illumination 0.2Lux - Voltage 12v - Operating Temp. -22˚F - 176˚F - NTSC - Reference Lines - Shutter Speed 1/60s - 20us - Waterproof - Pixels 656 x 492
OPEN CLOSE
Rev. 053115
TROUBLE SHOOTING 1. No video display while in reverse. - Make sure the dip switches are in the correct position. More support contact us.
Ves
VES MODES