Transcript
part #:
2720 850
00
S 700 E CU 2
Speed and power packed into one game-changing cutter.
TTER
Six pounds lighter than its predecessor, and just as powerful, the S 700E2 is light years ahead of anything the competition has to date. This battery-powered cutter performs heroic rescues without hoses or a power unit. It’s designed to take on current as well as future vehicle construction. Plus, it has 77% more cutting force where you need it.
Features and Benefits:
Technical Specifications:
• Highest cutting performance in the relevant work area
• Length: 36.2 in / 920 mm
• Unique blade geometry with three distinct cutting angles
• Width: 11.7 in / 296 mm
• Built for the high-strength steel of today and tomorrow’s vehicles
• Height: 10.3 in / 262 mm
• Ergonomically designed star-grip permits tool actuation from almost any gripping position
• Weight: 48.1 lbs / 21.8 kg
• Each tool comes with two batteries and one charger
• NFPA Cutter Rating: A8/B9/C8/D9/E9
• If needed, you can plug it in for limitless power with the eDRAULIC™ 110v adaptor
• NFPA 1936 2010 Compliant: Yes
8 0 0 . 5 3 7. 2 6 5 9 • 7 11 N . P O S T R O A D S H E L B Y, N C 2 8 15 0 • J A W S O F L I F E . C O M ©2014 Hurst Jaws of Life® • Sheet# S700E2 - 04.14
• Cutter Opening: 7.6 in / 192 mm
Product Specifications
S 700 E2 - 272085000
ELECTRO-HYDRAULIC CUTTER 1.
2.
3.
4.
5. 6. 7.
8.
9. 10. 11.
12. 13. 14. 15. 16. 17. 18.
The tool is designed to be a hydraulically operated piston activating mechanical joints symmetrically to open or close a set of two opposite blade arms whereby cutting surfaces go on top of each other without making contact thus enabling objects to be cut. Electro-hydraulic devices do not need to be connected to an external hydraulic source, generation of the required hydraulic pressure takes place within the body of the device by either a quick exchange lithium/ion battery or an external power supply. The electro-hydraulic tool is equipped with light-emitting diodes attached on the operating side to facilitate work under poor lighting conditions. For simplicity, the lights must be powered by the same Lithium-Ion battery that powers the electro-hydraulic tool and not a secondary battery The cylinder of the tool shall be made of anti-corrosive light aluminium alloy for its lightweight, strength and long life. The body of the tool shall have a high impact, non-metallic housing. The housing shall have ventilation holes on both sides of the unit for cooling the motor. The maximum cutter opening at the tips will be 7.6 in (192 mm). The cutter will be of slightly curved blade geometry for pulling the debris away and to the center with intelligent cutter geometry reducing tool movement and providing maximum cutting performance. The blades shall be made of investment cast dropped-forged steel which has a glass-pearl blasted finish and are regrind able. The blades of the tool should be attached to the piston rod via removable links for ease of repair, efficient power transmission and smooth operation. The pivot points of the blades shall have a rubber booted hand guard for safety purposes. The engineered curved blades with sophisticated geometry close at the tips and then pull the object to be cut towards the point where the maximum cutting force is applied to the relevant working range providing superior cutting performance and significantly reducing cutter wear. The cutting performance of the tool shall be able to cut up to 1.57 in (40 mm) diameter round stock steel. The tool shall have a dual pilot check valve to prevent accidental movement of the blades in the event of power loss. The control mechanism shall feature a star-grip control actuator for ease of operation by allowing 360 º operations in any position. The mechanism shall be separate and independent from the handle to provide added control in close-quarter operation. The tool must provide a non-interflow shear seal “dead man” actuator, whereby the unit stops functioning when thumb pressure is released. The opening and closing positions are clearly marked. The tool shall be protected by a pressure relief valve that prevents it from being over pressurized. The tool dimensions without the battery shall not be any longer than 36.2 (920 mm), wider than 11.7 in (296 mm) or higher than 10.3 in (262 mm). The maximum operating pressure to the tool will be 11,603 psi (80 MPa) (800 bar). The nominal electrical voltage (with power supply) is 24 V. The nominal electrical voltage (with lithium/ion battery) is 25.2 V. The current consumption should be 12 amp in idle mode and 45 amp at maximum load.
19. The tool shall be able to tolerate an ambient temperature range of -4ºF (-20ºC) up to +131ºF (+55ºC). 20. The tool must be NFPA 1936; 2015 Edition certified and shall be labelled as such bearing the mark of the testing agency. 21. Cutting classification should no less than A8 / B9 / C8 / D9 / E9 as defined in NFPA 1936; 2010 and certified by a 3rd party testing agency. 22. The tool will not weigh more than 49.4 lbs (21.8 kg) excluding the power supply.
part #:
2720 9500 0
S 311 E 2 C
UTT ER
The S 700E2’s little, but powerful, brother.
It may be the 700’s little brother but it doesn’t lack for power. This tool is the perfect extrication cutter and is the most convenient tool for getting to the action. Nearly four pounds lighter than its predecessor, this tool moves quickly at the scene – and past the competition.
Features and Benefits:
Technical Specifications:
• Smaller and lighter than its predecessor
• Length: 33.4 in / 847 mm
• Standard extrication cutter
• Width: 8.9 in / 225 mm
• Ergonomically designed star-grip permits tool actuation from almost any gripping position
• Height: 10.3 in / 262 mm
• Curved blade geometry pulls materials to the back of the blade area for fast, clean action
• Cutter Opening: 5.9 in / 150 mm
• Each tool comes with two batteries and one charger • If needed, you can plug it in for limitless power with the eDRAULIC 110v adaptor
8 0 0 . 5 3 7. 2 6 5 9 • 7 11 N . P O S T R O A D S H E L B Y, N C 2 8 15 0 • J A W S O F L I F E . C O M ©2014 Hurst Jaws of Life® • Sheet# S311E2 - 04.14
• Weight: 39.0 lbs / 17.7 kg
• NFPA Cutter Rating: A7/B8/C6/D7/E7 • NFPA 1936 2010 Compliant: Yes
Product Specifications 1.
2.
3.
4.
5. 6. 7.
8.
9. 10. 11.
12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
S 311 E2 - 272095000
ELECTRO-HYDRAULIC CUTTER
The tool is designed to be a hydraulically operated piston activating mechanical joints symmetrically to open or close a set of two opposite blade arms whereby cutting surfaces go on top of each other without making contact thus enabling objects to be cut. Electro-hydraulic devices do not need to be connected to an external hydraulic source, generation of the required hydraulic pressure takes place within the body of the device by either a quick exchange lithium/ion battery or an external power supply. The electro-hydraulic tool is equipped with light-emitting diodes attached on the operating side to facilitate work under poor lighting conditions. For simplicity, the lights must be powered by the same Lithium-Ion battery that powers the electro-hydraulic tool and not a secondary battery The cylinder of the tool shall be made of anti-corrosive light aluminium alloy for its lightweight, strength and long life. The body of the tool shall have a high impact, non-metallic housing. The housing shall have ventilation holes on both sides of the unit for cooling the motor. The maximum cutter opening at the tips will be 5.9 in (150 mm) measured at the end of the tips. The cutter will be of slightly curved blade geometry for pulling the debris away and to the center with intelligent cutter geometry reducing tool movement and providing maximum cutting performance. The blades shall be made of investment cast dropped-forged steel which has a glass-pearl blasted finish and are regrind able. The blades of the tool should be attached to the piston rod via removable links for ease of repair, efficient power transmission and smooth operation. The pivot points of the blades shall have a rubber booted hand guard for safety purposes. The engineered curved blades with sophisticated geometry close at the tips and then pull the object to be cut towards the point where the maximum cutting force is applied to the relevant working range providing superior cutting performance and significantly reducing cutter wear. The cutting performance of the tool shall be able to cut up to 1.34 in (34 mm) diameter round stock steel. The tool shall have a dual pilot check valve to prevent accidental movement of the blades in the event of power loss. The control mechanism shall feature a star-grip control actuator for ease of operation by allowing 360 º operations in any position. The mechanism shall be separate and independent from the handle to provide added control in close-quarter operation. The tool must provide a non-interflow shear seal “dead man” actuator, whereby the unit stops functioning when thumb pressure is released. The opening and closing position are clearly marked. The tool shall be protected by a pressure relief valve that prevents it from being over pressurized. The tool dimensions without the battery shall not be any longer than 33.4 in (847 mm), wider than 8.9 in (225 mm) or higher than 10.3 in (262 mm). The maximum operating pressure to the tool will be 10,878 psi (75 MPa) (750 bar). The nominal electrical voltage (with power supply) is 24 V. The nominal electrical voltage (with lithium/ion battery) is 25.2 V. The current consumption shall be 12 A in idle mode and 42 A with maximum load. The tool shall be able to tolerate an ambient temperature range of -4ºF (-20ºC) up to +131ºF (+55ºC). The tool must be NFPA 1936; 2015 Edition certified and shall be labelled as such bearing the mark of the testing agency. Cutting classification should be no less than A7/ B8 / C6 / D7 / E7 as defined in NFPA 1936;2010 and certified by a 3rd party testing agency. The tool will not weigh more than 39 lbs (17.7 kg) excluding the power supply.
part #:
SC 35 7 CO E2
2730 450
00
MBI TOO L
It combines cutting, spreading and being awesome.
The SC 357E2 uses a compact, single integrated design to house a tool that does so much. It cuts; it spreads; it’s perfect for first responders who need to be ready to accomplish anything. And do it fast.
Features and Benefits:
Technical Specifications:
• Newly designed hydraulic pump
• • • • • • • • • • • • • •
• More power reserve for the unexpected • Dead man control valve reverts to neutral position if worker’s hand slips • Dual pilot check valve sustains load requirements if hydraulic flow is interrupted • Ergonomically designed star grip permits tool actuation from almost any gripping position • Fast opening and closing action for increased speed during time-critical rescues
8 0 0 . 5 3 7. 2 6 5 9 • 7 11 N . P O S T R O A D S H E L B Y, N C 2 8 15 0 • J A W S O F L I F E . C O M ©2014 Hurst Jaws of Life® • Sheet# SC357E2 - 04.14
Length: 36.6 in / 929 mm Width: 8.8 in / 225 mm Height: 10.3 in / 262 mm Weight: 41.4 in / 18.8 mm Spreading Distance: 14.5 in / 368 mm Max. Spreading Force: 225,483 lbs / 1,003 kN Max. Pulling Force: 10,791 lbs / 48 kN NFPA HSF: 9,440 lbs / 42 kN NFPA LSF: 7,190 lbs / 32 kN NFPA HPF: 12,400 lbs / 55 kN NFPA LPF: 8,770 lbs / 39 kN NFPA Cutter Rating: A7/B7/C7/D7/E7 Cutter Opening: 10.8 in / 274 mm NFPA 1936 2010 Compliant: Yes
Product Specifications 1. 2.
3.
4.
5. 6. 7. 8. 9. 10. 11. 12. 13.
14.
SC 357 E2 - 273045000
ELECTRO-HYDRAULIC COMBINATION TOOL
The tool is a designed hydraulically activated piston with two equal, opposite blade arms that are symmetrically opened by mechanical joints, thereby spreading, squeezing, pulling or cutting objects. Electro-hydraulic devices do not need to be connected to an external hydraulic source, generation of the required hydraulic pressure takes place within the body of the device by either a quick exchange lithium/ion battery or an external power supply. The electro-hydraulic tool is equipped with lights to facilitate work under poor lighting conditions. For simplicity, the lights must be powered by the same Lithium-Ion battery that powers the electro-hydraulic tool and not a secondary battery The cylinder of the tool shall be made of anti-corrosive light aluminium alloy for its lightweight, strength and long life. The body of the tool shall have a high impact, non-metallic housing. The housing shall have ventilation holes on both sides of the unit for cooling the motor. The maximum spreading force shall be up to 225,483 lbf (1003 kN). NFPA HSF test point produced 9,440 lbf (42 kN), the LSF test point produced 7,190 lbf (32 kN). The tool shall produce a spreading distance up to 14.5 in (368 mm) measured at the blade tips. The tool shall produce a maximum pulling force of 10,791 lbf (48 kN). NFPA HPF test point produced 12,400 lbf (55 kN), the LPF test point produced 8,770 lbf (39 kN). To maximize the capability of the combination tool the unit should include an optional chain and shackle package for pulling operations, use only HURST chain set KSV 8/50. The tool shall produce a pulling distance of 15 in (380 mm). The tips are patented multifunctional tips that can be used for spreading, peeling, squeezing and pulling without the need to be changed. The tips are to be serrated and made from investment cast heat-treated steel. The tool shall product cutting forces up to 85,427 lbf (380 kN) measured at the rear end of the cutting surface and will be able to cut 1.3 in (32 mm) diameter round stock steel material. The maximum cutter opening shall be 10.8 in (274 mm) and shall include a notch to focus maximum cutting force. The blades of the tool shall be of a straight serrated edge design for maximum cutting performance. The blades shall have integral tips for spreading applications. The blades of the tool shall contain shackle holes for pulling applications. The blades of the tool should be attached to the piston rod via removable links, for ease of repair, efficient power transmission and smooth operation. The blades shall be made of investment cast dropped-forged steel glass pearl blasted for long-life and quality. The blades are regrindable. The pivot points of the blades shall have rubber booted hand guard for safety purposes. The control mechanism shall feature a star-grip control actuator for ease of operation by allowing 360 º operations in any position. The tool must provide a non-interflow shear seal “dead man” actuator, whereby the unit stops functioning when thumb pressure is released. The star grip automatically returns to the central position, guaranteeing the full load-holding.
15. The tool shall have two handles. One located at the center of the tool and the other located below the control mechanism. The center crossbar handle allows easy ergonomic manipulation from the center or either side. 16. The tool will be equipped with a dual pilot check valve. This is to prevent accidental movement of the arms in the event of power loss. 17. The tool shall be protected by a pressure relief valve that prevents it from being over pressurized. 18. The tool dimensions without the battery shall not be any longer than 36.6 (929 mm), wider than 8.8 in (225 mm) or higher than 10.3 in (262 mm). 19. The maximum operating pressure to the tool will be 10,200 psi (70 MPa) (700 bar). 20. The nominal electrical voltage (with power supply) is 24 V. The nominal electrical voltage (with lithium/ion battery) is 25.2 V. 21. The estimated current consumption at nominal voltage is 12 amps at idle mode and 40 amps at maximum load. 22. The noise pressure level in idle mode shall be 69 dB(A) and 71 dB(A) in maximum load. 23. The tool shall be able to tolerate an ambient temperature range of -4ºF (-20ºC) up to +131ºF (+55ºC). 24. The tool must be NFPA 1936; 2015 Edition certified and shall be labelled as such bearing the mark of the testing agency. 25. Cutting classification should be no less than A7 / B7 / C7 / D7 / E7 as defined in NFPA 1936;2010 and certified by a 3rd party testing agency.
SC 357 E2 - 273045000 26. The tool will not weigh more than 41.4 lbs (18.8 kg) excluding the power supply.
SP 31 0 SPR E2
part #:
2710 850
00
EAD ER
An extra-strength spreader for extra-strength rescues. The superior ergonomics, durable construction and “diamond” surface tips make this tool the beast of the eDRAULIC™ spreader line. Its strength makes it perfect for urban disaster recovery and traffic accidents.
Features and Benefits:
Technical Specifications:
• Newly developed hydraulic pump provides extra power
• Length: 37.6 in / 955 mm
• Dead man control valve reverts to neutral position if worker’s hand slips from control
• Width: 13.6 in / 345 mm
• Dual pilot check valve sustains load requirements if hydraulic flow is interrupted
• Weight: 52.7 lbs / 23.9 kg
• Ergonomically designed star grip permits tool actuation from almost any gripping
• Height: 10.9 in / 276 mm • Spreading Distance: 28.5 in / 725 mm • Max. Spreading Force: 72,800 lbs / 324 kN • Max. Pulling Force: 9,900 lbs / 44 kN • NFPA HSF: 13,000 lbs / 58 kN • NFPA LSF: 10,300 lbs / 46 kN • NFPA HPF: 7,600 lbs / 34 kN • NFPA LPF: 5,800 lbs / 26 kN • NFPA 1936 2010 Compliant: Yes
8 0 0 . 5 3 7. 2 6 5 9 • 7 11 N . P O S T R O A D S H E L B Y, N C 2 8 15 0 • J A W S O F L I F E . C O M ©2014 Hurst Jaws of Life® • Sheet# SP310E2 - 04.14
Product Specifications
SP 310 E2 - 271085000
ELECTRO-HYDRAULIC SPREADER 1.
The tool is a designed hydraulically activated piston with two equal, opposite light metal alloy spreader arms that are symmetrically opened by mechanical joints, thereby spreading objects. Closing the spreader arms is also carried out hydraulically and mechanically by reverse order of the piston. 2. Electro-hydraulic devices do not need to be connected to an external hydraulic source, generation of the required hydraulic pressure takes place within the body of the device by either a quick exchange lithium/ion battery or an external power supply. 3. The electro-hydraulic tool is equipped with lights to facilitate work under poor lighting conditions. For simplicity, the lights must be powered by the same Lithium-Ion battery that powers the electro-hydraulic tool and not a secondary battery. 4. The cylinder of the tool shall be made of anti-corrosive light aluminium alloy for its lightweight, strength and long life. The body of the tool shall have a high impact, non-metallic housing. The housing shall have ventilation holes on both sides of the unit for cooling the motor. 5. The spreading force shall be up to 72,800 lbf (324 kN). 6. The tool shall produce a maximum spreading distance of 28.54 in (725 mm). 7. According to NFPA testing standards the HSF test point produced 13,000 lbf (58 kN), the LSF test point produced 10,300 lbf (46 kN). 8. To maximize the capability of the spreader the unit should include an optional chain and shackle package for pulling operations, use only HURST chain set KSV 11. This should not require the removal of the tips for attachment. According to NFPA testing standards the HPF test point produced 7,600 lbf (34 kN), the LPF test point produced 5,800 lbf (26 kN). 9. The tool shall produce a pulling distance of 18.7 in (475 mm). 10. The tips are of a unique cross section diamond design providing excellent gripping with minimal slippage during spreading and lifting operations. The tips are to be made from investment cast heat-treated steel. 11. The arms of the tool should be made of aluminium alloy and attach via removable links for ease of repair, efficient power transmission and smooth operation. The pivot points of the arms shall have a rubber booted hand guard for safety purposes. 12. The control mechanism shall feature a star-grip control actuator for ease of operation by allowing 360 º operations in any position. The tool must provide a non-interflow shear seal “dead man” actuator, whereby the unit stops functioning when thumb pressure is released. The star grip automatically returns to the central position, guaranteeing the full load-holding. 13. The tool shall have two handles. One located at the center of the tool and the other located below the control mechanism. The center crossbar handle allows easy ergonomic manipulation from the center or either side. 14. The tool will be equipped with a dual pilot check valve. This is to prevent accidental movement of the arms in the event of power loss. 15. The tool shall be protected by a pressure relief valve that prevents it from being over pressurized. 16. The tool dimensions without the battery shall not be any longer than 37.6 in (955 mm), wider than 13.6 in (345 mm) or higher than 10.9 in (276 mm). 17. The maximum operating pressure to the tool will be 10,878 psi (75 MPa) (750 bar). 18. The nominal electrical voltage (with power supply) is 24 V. The nominal electrical voltage (with lithium/ion battery) is 25.2 V. 19. The tool shall be able to tolerate an ambient temperature range of -4ºF (-20ºC) up to +131ºF (+55ºC). 20. The tool must be NFPA 1936; 2015 Edition certified and shall be labelled as such bearing the mark of the testing agency. 21. The tool will not weigh more than 52.7 lbs (23.9 kg) excluding the power supply.
Product Specifications
R 421E2 Ram - 274085000
RESCUE RAM
1.
The rescue ram is a double-acting hydraulic cylinder. Extension and retraction is carried out hydraulically.
2.
The rescue ram is a multi-stage cylinder for applying pressure with varying pressure forces depending on the piston stage. The pressure force remains constant within one piston stage.
3.
The ram shall extend to a distance of up to 53 in (1347 mm). The retracted length is to be no less than 23.5 in.(313 mm).
4.
The ram shall feature a two stage stroke. The maximum stroke for piston 1 shall be 15.2 in (387 mm) producing up to 28,600 lbf (127 kN) force. The maximum stroke for piston 2 shall be 14.3 in (363 mm) producing up to 13,500 lbf (60 kN) force. The piston stroke overall shall be 29.5 in (750 mm).
5.
The tool shall include heat-treated, investment-cast steel ram claw feet on the piston side and on the cylinder side for durable gripping and minimizing slippage.
6.
The tool shall have a dual pilot check valve to prevent accidental movement of the piston rod in the event of power loss.
7.
The control mechanism shall feature a star-grip control for ease of operation by allowing 360º operation in any position. The mechanism shall be separate and independent from the handle to provide added control in close-quarter operation.
8.
The tool must provide a “dead man” actuator whereby the unit stops functioning when hand pressure is released.
9.
The extend piston and retract piston are clearly marked.
10. The tool must be NFPA 1936; 2015 Edition certified and shall be labelled as such bearing the mark of the testing agency. 11. The tool will not weigh more than 41.9 lbs (19 kg) excluding the power supply. 12. Electro-hydraulic devices do not need to be connected to an external hydraulic source, generation of the required hydraulic pressure takes place within the body of the device by either a quick exchange lithium/ion battery or an external power supply. 13. The electro-hydraulic tool is equipped with lights to facilitate work under poor lighting conditions. 14. The cylinder of the tool shall be made of anti-corrosive light aluminium alloy for its lightweight, strength and long life. The body of the tool shall have a high impact, non-metallic housing. The housing shall have ventilation holes on both sides of the unit for cooling the motor. 15. The tool shall be able to tolerate an ambient temperature range of -4ºF (-20ºC) up to +131ºF (+55ºC).
