Transcript
www.arctic.ac
S113 BT EN Manual
4.0
Packaging Contents Speaker x 1
3.5 mm Cable (30cm) x 1
Micro USB Cable (80cm) x 1 Carrying Case x 1
Manual x 1
Function Diagram
OFF/ON
POWER
LINE IN
Power Switch Micro-USB Charging Port 3.5 mm Audio Input Volume up / Next Track Multifunction button for Answer Phone / Pairing Volume Down / Previous Track
LED Light Signals Blue ŸBlue light flashing means the speaker device is on and not paired. ŸBlue light flashing every five seconds means speaker is paired to a device. Red ŸRed light flashing means battery is low ŸRed light on constantly means charging Red & Blue ŸWhen both the red and the blue lights are rapidly flashing, it means the speaker is searching for device to pair with.
Getting Connected The S113 BT allows you to pair with your mobile device in three different ways: A. Bluetooth Pairing 1. Turn on S113 BT by sliding the power switch. 2. Activate pairing mode on your S113 BT by pressing the Multifunction button for 8 seconds until the red and blue LED's flash alternately. (Not necessary for reconnection). 3. Turn on Bluetooth on your phone and pair it with the speaker. Example: iOS
Select Bluetooth
Switch On Bluetooth
Click Settings
Bluetooth is On Now Connected Select S113 BT
Example: Android 4.0
ON
OFF
Switch On Bluetooth
Bluetooth is On
Click Settings
ON
Click Search for Devices
ON
ON
Select S113 BT
Now Connected
Notes: ŸPairing mode will last up to five minutes or until a device is found, two tones will sound to let you know when pairing has stopped. ŸIf you exceed the effective range of approx. 10M (33ft) the speaker will disconnect and will automatically reconnect if the speaker re-enters the effective range within ten minutes.
B. NFC One Touch Pairing (only for NFC enabled phones) 1. Turn on the S113 BT speaker by sliding the power switch. 2. Enable NFC on your mobile device. 3. Slide your phone very slowly from top to bottom across the speaker directly above the multifunction button until you hear a beep and a confirmation message comes up on your mobile device. 4. Play music!
C. Connect via Cable 1. Turn on S113 BT speaker by sliding the power switch. 2. Insert one end of the 3.5mm audio cable into the speaker and the other end into your mobile device headphone's output. 3. Play music!
Reconnection Via Bluetooth 1. Turn on Bluetooth on phone. 2. Turn on S113 BT by sliding the power switch. 3. If your device was the latest one to be paired with the S113 BT it will connect automatically otherwise please repeat pairing section. Via NFC 1. Enable NFC on your phone 2. Turn on S113 BT by sliding the power button. 3. Slide your phone very slowly from top to bottom across the speaker directly above the multifunction button (Picture) until you hear a beep and a confirmation message comes up on your mobile device.
Music Operations ŸVolume up: one short press of the ŸVolume down: one short press of the ŸNext track: while music is playing, press and hold the
until the track moves to the next track. ŸPrevious track: while the music is playing, press and hold
the until the start of the track replays. Quickly press and hold the again to go to the previous track. ŸPause / Play: one short press and release of the
multifunction button
Phone Operations If the mobile device that is paired with the S113 BT speaker is a cellular phone you can: ŸAnswer Call: one quick press of the multifunction button ŸEnd Call: one quick press of the multifunction button
.
.
ŸReject Call: pressing and holding the multifunction button
for three seconds or until you hear a tone that indicates this function has been completed. ŸVoice Recognition: If supported by your mobile device, turn
the voice recognition feature on, in standby mode press and hold the multifunction button for three seconds; a tone will sound to indicate activation. Say the name of who you would like to call and wait for the dial tone.
Charging The S113 BT can be charged while switched on or off. 1. Insert the micro USB cable into the S113 BT and the USB side into a power source. (We recommend the Charger Pro 4). 2. When the red LED disappears the S113 BT is fully charged.
It is recommended to fully charge before initial use.
Reset To reset your speaker to factory settings; 1. Switch the S113 BT on. 2. Then press the and buttons simultaneously for 10 seconds until a low key beep is emitted. 3. Switch the speaker off.
Caution ŸWireless connections are affected by obstructions such as
walls and other devices. ŸKeep S113 BT dry moisture may damage electronic
components. ŸExposure to high temperature will shorten the life and damage electronic components. ŸOpening / altering the S113 BT voids all product warranty. ŸRough handling may damage inside electronic components.
Like us on facebook www.facebook.com/ARCTIC.en
© 2013 CSR plc and its group companies. The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by ARCTIC (HK) Ltd. is under license. Other trademarks and trade names are those of their respective owners. FCC ID ZG8BSK10 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
© 2013 ARCTIC Switzerland AG. All Rights Reserved. No part of this manual including the products described in it, may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purpose, without the express written permission of ARCTIC Switzerland AG. In no event shall ARCTIC its directors or employees be liable for any indirect damages, incidental or consequential damages arising from any defect or error in this manual or product.
