Transcript
P P
INSULATION SHEATHING STAPLER MODEL S200 W16 WIDECROWN (15/16")
TOOL SCHEMATIC AND PARTS IMPORTANT! DO NOT DESTROY Always refer to safety and operating manuals, #403606, #405218 and #405222 for detailed information on this tool. It is the customer's responsibility to have all operators and service personnel read and understand this information.
PARTS LEGEND 1 2 3 4 5 *6 7 *8 9 10 * 11 * 12 * 13 * 14 15 16 17 18 19 * 20 21 22 23 24 * 25 * 26 * 27 28 29 30 31 32 33 34 35 36 37 38 ▲ 39 40 41 * 42
501043 500956 501299 501254 402717 404230 501250 091452 404054 404056 090927 092775 092773 404256 500954 015660 403582 405430 501252 404182 501322 402725 405243 501251 402728 091966 500369 501227 500975 501140 501141 402708 501229 402754 402706 091545 501023 500957 500963 097748 097746 092174
1 1 6 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1
S200 W16, 501265
T.H.S.C.S. 1/4-20 x 1/2" Cap Diffuser S.H.C.S. 1/4-20 x 1-1/2" Cap Conical Spring Retaining Ring Upper Valve Piston O-Ring Seal, Main Valve Lower Valve Piston O-Ring, Main Valve O-Ring, Main Valve O-Ring, Main Valve O-Ring Post, Main Valve S.H.C.S. 10-24 x 1/2" Driver Blade Nut O-Ring, Piston Piston Driver Blade Sleeve Retainer Seal Sleeve Flange Sleeve Sleeve O-Ring, Sleeve O-Ring, Sleeve O-Ring, Sleeve Bumper Retainer Gasket Cap Logo Housing Left Logo Housing Right Gasket Nose Flange Bumper Seal Driver Blade Flange Nose S.H.C.S. 1/4-20 x 7/8" Grip Handle Housing End Plug Spring Valve Pin Valve Pin O-Ring, Valve Body
43 44 45 46 47 48 49 50 51 52 ▲ 53 54 55 * 56 ▲ 57 58 59 60 61 62 63 64 65 ** 66 67 68 69 70 71 72 73 * 74 75 76 77 78 79 * 80 81 82 83
026133 401958 402668 501008 501010 501009 402669 092037 004502 402781 004224 402743 091534 091532 091568 402760 402486 402758 402759 402740 402780 501291 404849 500459 404698 402730 405079 501208 501209 501206 501212 402734 402763 402629 403716 402608 402736 402738 501320 071297 501244
2 1 3 1 1 1 1 4 4 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1
Roll Pin 1/8 x 1 Valve Body Retaining Washer Trigger Lever Trigger Roll Pin Trigger Pin Locknut S.H.C.S. 10-32 x 5/8" Rail Bracket S.H.C.S.10-32 x 3/8" Pin Negator Drum Drum, Negator Negator Bd. Head Screw 6-32 x 1/4" Follower Retaining Washer Latch Follower Button Spring Follower Latch Roll Pin 3/32 x 7/16 Pivot Rail Cover Assembly Nameplate Rail & Rail Cover Assembly Warning Label Roll Pin Assembly Pivot Pin Front Guide Spring Front Guide Latch Latch Guide Latch Pin Back Plate Front Guide Spring W.C.E. Upper W.C.E. Hardened Washer S.H.C.S. 10-32 x 5/16" Lower W.C.E. Flat Washer #10 Spring Guide Block Roll Pin 1/8 x 1-1/8" Intermediate W.C.E.
AIR CONSUMPTION CHART
* Denotes normal wear items. ** Make sure warning label (500459) is properly affixed. Replace if necessary. Label available at no charge through the Service Dept.
▲ Apply Loctite 242 (Blue) Part No. 093500 ➔ Denotes new change.
AIR CONSUMPTION - SCFM/FASTENER
.050
.045
.040 .040
.035
.030
70
80 90 100 110 AIR PRESSURE - PSIG
120
21 S200 W16
1 22
2
25
23
3
24
26 Cap Assembly #501262
4
501265
27 37
28 5
3
29
8
38
Main Valve Assembly #501261
6 40 41
7 9 11
31
32
10
12 13
44
46
17
18
55
48 47
56 57
63
59
62
80
61 60 64
82 83
76
58 45
66
19 20
54
36
81 77
Trigger Assembly #501048
49
16 Piston Assembly #501267
53 43
34 35
15
51
52
42
45
33
14
50
51 30
39
14
67
65
68 69 74 77
51
76
73
72
70 45 71
75
50 79
78
WARNING All parts must be periodically inspected and replaced if worn or broken. Failure to do this can affect the tool's operation and present a safety hazard
ACCESSORIES Sequential Operating Kit This special attachment is designed for sequential operation (stops "contact" firing). The operator must depress and hold the work contacting element against the worksurface before pulling the trigger. This sequence must be repeated each timethe tool drives a fastener.
Part No. 501039
Remote Fire Valve This valve via a positive air signal allows a machine mounted tool to be operated from an automatic air valve or foot pedal system.
Part No. 1X0713
Large Nylon Tool Bag
Part No. 219046
Wide Crown Stapler Repair Kit This kit repairs all air leaks except for the trigger valve. Part No. 219220 Trigger Valve Repair Kit This kit repairs all trigger valve air leaks. Part No. 219224
Safety Glasses Clear
Part No. 402510
Tinted
Part No. 402512
Lubricants and Loctite Lubricant 1 lb. Lubricant 5 gram tubes Loctite 242 (Blue) 1 oz. Lubricating Oil 16 oz. Lubricating Oil 8 oz. with Antifreeze
Part No. 403734 Part No. 219188 Part No. 093500 Part No. 403720 Part No. 219090
Degreaser Cleaner Ideal cleaner for all Paslode tools.
Part No. 219086
Belt Hook Attaches to tool enabling you to carry tool on belt holder. Part No. 500955 Belt Hook Holder Attaches to work belt and carries tool using the above belt hook. Part No. 219028
SAFETY INSTRUCTIONS
DO NOT EXCEED MAXIMUM RECOMMENDED AIR PRESSURE
WEAR EYE AND HEARING PROTECTION
60
0
120
Always wear hearing protection and eye protection devices, including side shields when operating or working in the vicinity of a tool.
120
0
60
Operate the tool using only the recommended air pressure. Do not exceed the maximum air pressure marked on the tool. Be sure the air pressure gauge is operating properly and check it at least twice a day.
Never use any bottled air or gases such as oxygen to operate the tool since they could cause the tool to explode.
Printed in U.S.A. © 2005, Illinois Tool Works, Inc.
P
An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061
501353-3 09/05
