S7010 869– 894 Mhz / 40w Cdma/gsm/w-cdma

Transcript

S7010 869– 894 MHz / 40W CDMA/GSM/W-CDMA Key Feature        Solid-state Pre-D linear design Small form factor and lightweight Suitable for SMR, iDEN and multi FA Applications. 50 Ohm Input / Output impedance High reliability and ruggedness Built-in high dynamic range ALC circuit and control functions Built-in Output Circulator ELECTRICAL SPECIFICATIONS @ +28 VDC, 25C, 50  System Parameter Symbol Operating Frequency BW Output Power CW PSAT Output Power @ 1dB G.C.P P1dB Power Output CDMA per IS-97 PCDMA Gain at Rated POUT G Input Power Range with ALC ON PIN Small Signal Gain Flatness G Gain Flatness @ 46 dBm, PIN = 0 dBm, (ALC ON) GALC Input/Output Return Loss S11 / S22 Third Order Intercept Point IP3 2-Tones, POUT = 12 W Avg., ∆ = 500 KHz Harmonics @ P1 dB Gain Compression Point H Noise Figure NF Spurious Signals Spur Operating Voltage VDD Supply Current @ POUT = 40 W CW IDD Supply Current @ POUT = 12 W Composite IDD MECHANICAL SPECIFICATIONS Parameter Dimensions RF Connectors In/Out DC / Control Connector ENVIRONMENTAL CHARACTERISTICS Parameter Operating Case Temperature Storage Temperature Relative humidity (non-condensing) Unit MHz Watt Watt Watt dB dBm dB dB dB +62dBm Min. dBm -45dBc Max. 10dB Max. -60dBc Max. 28V 6.0A Max. 3.5A Typ. dBc dB dBc Volt Amp Amp Value SMA Female D-Sub 9-Pin, Male Symbol Tc Tstg RH PROTECTIONS Input RF drive level without damage Load VSWR @ Rated POUT Thermal Overload Ph. 82 (032) 670-8510~2 Fax. 82 (032) 670-8513 Specifications 869-894MHz 50W Min. 50W Typ. 10W Min. 55dB Min. -6dBm Min. +5dBm Max. ±0.75dB Max. ±0.5dB Max. -14dB Max. Specifications 0 ~ +75 -40 ~ +85 ~ 95 Unit °C °C % +10 dBm ∞ @ all load phase & amplitude 85C shutdown www.RFzone.com Rev. 1.0 / 07-05-2014 S7010 869– 894 MHz / 40W CDMA/GSM/W-CDMA INTERFACE CONNECTOR - D-Sub, 9 Pin Description Pin # 1 Forward Power Monitor 2 Reverse Power Monitor 3 ALC ON/OFF 4 ALC Level 5 Mute 6&7 8&9 VDD GND Specifications Continuous Analog voltage relative to forward power via RMS detector FWDM: 27 – 47 dBm @ 0 – 5 V (100 mV/dB) Continuous Analog voltage relative to reflected power via RMS detector REVM: 24 – 44 dBm @ 0 – 5 V (100 mV/dB) ALC ON = TTL “High” ALC OFF = TTL “Low or Open” Continuous adjustable range via analog input levels Input Power Range: -6dBm to +5dBm Setting Point (ASP): 33 – 47 dBm @ 0 – 5 V (250 mV/dB) 46 dBm @ 4.75 V Error Range (AER): ±1.5 dB Response Time (ART): 100 mS/dB Amplifier Enable: TTL “Low” or Open Amplifier Disable: TTL “High” +28V±2VDC Ground LED LED Indicator Output Power level indicator referenced to ALC setting Ph. 82 (032) 670-8510~2 Fax. 82 (032) 670-8513 www.RFzone.com Rev. 1.0 / 07-05-2014