Transcript
Operating Instructions |
Sartorius Element Series Electronic Precision Balances, Electronic Gem Scale
98648-013-89
English
– Seite 3
bcd – ࡍࠫ 21
2
Contents
3 Warnings and Safety Precautions 4 Getting Started 8 Operation 8 Basic Weighing Function 8 Description of the Keys 9 9 10 11 12 13 14
Application Programs Toggling between Weight Units Counting Weighing in Percent “Hold” Display Totalizing Specific Gravity
15 Calibration/Span Adjustment 16 Configuration (Setup Menu) 17 Error Codes 18 18 19 20
Overview Specifications Accessories (Options) C Marking
Warnings and Safety Precautions Safety Information § To prevent damage to the equipment, please read these operating instructions carefully before using your balance/scale. ! Do not use this equipment in
hazardous areas. ! Make sure the voltage rating printed
on the power supply is identical to your local line voltage. ! Use only commercially available non-
rechargeable or rechargeable battery: 8 + AA, Mignon (not included). The rechargeable batteries are not charged when you use the AC adapter. Please use the charger to recharge the batteries outside the balance/scale. – The balance/scale is energized at all times unless you disconnect the AC adapter and, if connected, the battery. – Protect the AC adapter from contact with liquid ! Exposure to excessive electromagnetic
interference can cause the readout value to change. Once the disturbance has ceased, the instrument can be used again in accordance with its intended purpose. Installation – It is recommended to connect Sartorius accessories and options, as these are optimally designed for use with your balance. – Do not open the balance/scale housing as this may void the manufacturer’s warranty.
3
Getting Started
– – – –
Equipment Supplied Balance/scale Weighing pan Plug-in AC adapter Level indicator and adjustable feet
Additional equipment with models ELT602, ELT402, ELT202, ELT1001, ELT601: – Calibration weight Additional equipment with model ELT103, GD502: – Calibration weight – Round glass draft shield – Only with GD502: Gem tray
– – – –
Installation Choose a location that is not subject to the following negative influences: Heat (heater or direct sunlight) Drafts from open windows and doors Extreme vibrations during weighing Excessive moisture
Setting Up the Balance/Scale § Place the components on the balance/scale in the following order: – Weighing pan – Round glass draft shield on model ELT103, GD502
4
! Use only original Sartorius AC adapters: – for Asia: 400081.1 – for the U.S.: 400314.1
Connecting the Balance/Scale to AC Power § Insert plug into the jack (located on back of the balance/scale) § Plug the AC adapter into an electrical outlet ! LISTED power supply 11 V–21 V compliant with
NEC Class 2 output.
Below-Balance/Scale Weighing A port for a below-balance/scale weighing hanger is located on the bottom of the balance/scale. § Open the cover plate on the bottom of the balance/scale. § Attach the sample (e.g., using a suspension wire) to the hanger. $ Install a shield for protection against drafts if necessary.
5
Using a Non-Rechargeable/Rechargeable Battery (not for model ELT103, GD502) $ A non-rechargeable or rechargeable battery is not included with the equipment supplied. ! Use only a commercially available non-rechargeable
(8+ AA/Mignon) or rechargeable battery. ! When using a rechargeable battery, be sure to
recharge it outside the balance/scale using a separate charger. G Lay the balance/scale on its side G Lift the compartment cover G Insert the non-rechargeable (8+ AA/Mignon) or rechargeable batteries into the compartment. $ Make sure to connect the positive and negative poles correctly. G Close the battery compartment: press down on the cover until it clicks into place. ! All used batteries are classified as waste that requires
special handling (not “household” waste). Dispose of rechargeable batteries in accordance with the applicable special waste disposal regulations.
6
Leveling the Balance/Scale § Always level the balance/scale again any time after it has been moved to a different location. Example: moving bubble from R to L § Turn the feet as shown in the diagram until the air bubble is centered within the circle of the level indicator. > In most cases this will require several adjustment steps.
Removing Weights for Calibration/Span Adjustment (only for models ELT103, ELT602, ELT402, ELT202, ELT1001, ELT601, GD502) § Grasp the tab to turn and pull out the weight compartment. $ Follow instructions on page 14 for calibration/span adjustment.
7
Operation
Basic Weighing Function Features – Zeroing the balance/scale You can zero the balance/scale within the entire weighing range, up to the maximum capacity. Preparation § Switch on the balance/scale: press the e key § If necessary, zero the balance/scale: press the w key $ If necessary, change the configuration settings: see the chapter entitled “Configuration” $ If desired, load the factory settings: see the chapter entitled “Configuration,” menu item 9.– 1 Additional functions $ Switching off the balance/scale: press the e key $ Battery operation: automatic shut-off after 2, 5 or 10 minutes; see chapter on configuration. Example: 2 minutes. If the weight readout remains unchanged and no keys are pressed for at least two minutes, the battery symbol “ ” starts flashing. After another 2 seconds, the balance/scale shuts off automatically, unless a key is pressed. Example: Determine weight of sample Step 1. Switch on the balance/scale Self-test runs Display: Software version
Description of the Keys
e On/off key: switches the balance/scale on and off or switches it to the standby mode. Battery operation: on; turns backlight on; off w Press less than 2 seconds: zeros the balance/scale Press and hold 2 seconds: opens the application menu q Starts calibration/adjustment v Starts an application program Scrolls in the application, configuration and in the calibration menus Enter Confirms the selected setting; CF exits application, configuration & calibration menu if key is pressed and held for at least 2 seconds. r Generates a printout or data output
Key (or instruction) e
r 31.01 g 52.0 g
2. Place container on the balance/scale (in this example, 52 g) 3. Zero the balance/scale 4. Place sample in container on balance/scale (in this example, 150.2 g).
8
Display
w
0.0 g 150.2 g
Application Programs
Toggling between Weight Units With this application program you can toggle the display of a weight value back and forth between two weight units (see table below). Example: Toggle weight unit from pounds [lb] (application) to grams [g] (basic unit) Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Toggling between Weight Units
v
3. Confirm unit 4. Select weight unit; in this example: “5. Pounds” (see table below) 5. Confirm weight unit (pounds)
Display
Enter CF
v repeatedly
Enter CF
6. Place sample on balance/scale
7. Toggle weight unit
Menu code 1. user 1) 2.grams (fact. setting ELT models) 4.carat (fact. setting GD502)
5.Pound 6.ounce 7.tryo 8.tl.hon 9.tl.sin 10.tl.ta 11.grai 12.peny 15.tl.ch 22.pdoz 23.newt
v
Unit Grams Grams Carats Pounds Ounces Troy ounces Hong Kong taels Singapore taels Taiwanese taels Grains Pennyweights Chinese taels lb/oz Newtons
Conversion factor 1.00000000000 1.00000000000 5.00000000000 0.00220462260 0.03527396200 0.03215074700 0.02671725000 0.02645544638 0.02666666000 15.4323583500 0.64301493100 0.02645547175 0.03527396200 0.00980665000
Display o g o lb oz ozt tlk tl tl GN dwt tl lb:oz N
1
) User-defined conversion can be loaded in balance with RS-232 or USB program option.
9
Counting
Purpose With the Counting program you can determine the number of parts or items by weighing. Example: Determine the number of uncounted parts; weigh in the selectable reference sample quantity (in this example: 20) Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Counting
v repeatedly
3. Confirm setting Symbol “ ” on the display: application is active
Display
Enter CF
4. Place empty container on the balance/scale 5. Zero the balance/scale
w
6. Place reference sample quantity (20) on the balance/scale 7. Select reference sample quantity: in increments of 1 (1, 2, 3, ..., 99) or in increments of 10 (10, 20, 30, ...,100) 8. Confirm selected reference sample quantity
v repeatedly (briefly) or v > 2 sec. Enter CF
9. Place uncounted parts on balance/scale 10. Toggle display between mean piece weight, total weight, and quantity
v repeatedly
11. Unload the balance/scale 12. Counting application: clear the reference value 13. Reactivate Counting (if no other application program has been selected) 14. Repeat procedure starting from Step 5
10
Enter CF
v
> 2 sec
Weighing in Percent
Purpose This application program allows you to obtain weight readouts in percent which are in proportion to a reference weight. Example: Determine an unknown percentage; store the weight on the balance/scale as the reference percentage (100%) Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Weighing in Percent
v repeatedly
3. Confirm setting Symbol “ ” on the display: application is active
Display
Enter CF
4. Place empty container on the balance/scale 5. Zero the balance/scale
w
6. Place the reference weight for 100% on the balance/scale 7. If desired, change the number of decimal places displayed: 100.0%, 100.00% or 100% (factory setting) 8. Confirm selected no. of decimal places
v repeatedly Enter CF
9. Place unknown weight on the balance/scale 10. Toggle display between weight and percentage
v repeatedly
11. Unload the balance/scale 12. Weighing in Percent application: clear the reference percentage 13. Reactivate Weighing in Percent (if no other application program has been selected)
Enter CF
> 2 sec
v
14. Repeat procedure starting from Step 5.
11
“Hold” Display
Purpose The last stable value remains displayed for 5 seconds after removing the sample from the pan. Example: Determine weight of oversized sample Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Display Hold (“HLdon”)
v repeatedly
3. Confirm setting Symbol “ ” on the display: application is active 4. If necessary: zero the balance/scale
Enter CF
w
5. Place sample on balance/scale
6. Start application program
v
Symbol “ ” flashes on the display: the weight value is locked 7. Unload the balance/scale: the weight value remains displayed for a further 5 seconds; or 8. Zero the balance/scale 9. End the Display Hold application 10. Reactivate Display Hold (if no other application program has been selected) 11. Repeat procedure starting from Step 5.
12
w Enter CF
v
> 2 sec
Display
Totalizing
Purpose With this application program you can add up successive weight values exceeding the capacity of the balance/scale. Example: Totalizing weight values Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Totalizing
v repeatedly
3. Confirm setting Symbol “ ” on the display: application is active 4. If necessary: zero the balance/scale
Display
Enter CF
w
5. Place sample on balance/scale (in this example, 380 g) 6. Store value in memory. Total weight is displayed steadily; s symbol flashes.
Enter CF
7. Remove sample from balance/scale 8. Place the next sample on the balance/scale (in this example, 575 g) 9. Store value in memory. Totalized stored weight is displayed; symbol s flashes. Note: s symbol remains on indicating stored value in memory until cleared
Enter CF
10. To view the current weight for 2 seconds (if a printer is connected, a printout is generated)
v
11. Clear totalizing memory (if a printer is connected, total is printed)
v > 2 sec
12. End Totalizing 13. Reactivate Totalizing (if no other application program has been selected) (if a printer is connected, total is printed).
Enter CF
> 2 sec
v
14. Repeat procedure starting from Step 6.
13
Specific Gravity
Purpose Use this application program to determine the specific gravity of a sample. The result is displayed with one decimal place. Beaker and wire not included with balance/scale. Example: Determine the specific gravity of a solid. Step
Key (or instruction)
1. Select application program
w > 2 sec
2. Select Specific Gravity
v repeatedly
3. Confirm setting Symbol “ ” on the display: application is active
Enter CF
4. If necessary, zero the balance/scale
w
5. Start application program
v
6. Confirm the display, “airval”
Enter CF
7. Determine weight of the sample in air: place sample on the balance/scale 8. Store weight-in-air value
Enter CF
9. Remove sample from balance/scale 10. Determine weight of sample in liquid: connect wire and set up beaker 11. Confirm the display “Water”
Enter CF
12. Place sample in liquid 13. Store the weight-in-liquid value and view the result 14. Clear the display 15. Exit the Specific Gravity application 16. Reactivate Specific Gravity (if no other application program has been selected) 17. Repeat procedure starting from Step 5.
14
Enter CF
w Enter CF
v
> 2 sec
Display
Calibration/Span Adjustment
Calibration is recommended after initial installation and each time the balance/scale is moved. Features Calibration/adjustment can be performed only when: – there is no load on the balance/scale, – the balance/scale is zeroed, and – the internal signal is stable. If these conditions are not met, an error message is displayed.
The weight required for calibration/ span adjustment is displayed. Standard calibration weights for selected models: to remove, see instructions on page 6. Press v to select a different weight value. To cancel the procedure: press and hold the Enter key (> 2 sec.). CF
Example: Calibrate/adjust span of the balance/scale (here: model ELT 6001) Step
Key (or instruction)
1. Switch on the balance/scale
e
2. Zero the balance/scale
w
3. Start calibration The preset calibration weight is displayed without the weight unit (in this example, 5000 g)
q
4. To select a different calibration weight value
5. Confirm calibration weight value and adjustment
Display
v repeatedly
Enter CF
start calibration/span
After the zero point is stored, the required calibration weight flashes on the display. 6. Place the required calibration weight on the balance/scale The readout stops flashing if the weight is applied within the defined time limit and tolerance. If the weight value is accepted, the display stops flashing and the stability symbol appears on the display. 7. Remove the calibration weight 8. Calibration/span adjustment has been completed
15
Configuration (Setup Menu)
To configure the balance/scale; i.e., adapt the balance/scale to individual requirements. Step
Key (or instruction)
1. Switch off the balance/scale
e
2. Switch on the balance/scale and
e
while all segments are displayed
Display
w briefly
Navigation in the Setup Menu Key
Press briefly
Enter CF
Menu level: Move to the right (cyclical) v Menu item: Scrolling w Menu level: Move to the left
Parameter Settings (Overview) Setup menu
1 Weighing
ο Factory setting
√ User-defined setting
1.1. Adapt filter
1.1.1 1.1.2 1.1.3 1.1.4
Very stable conditions ο Stable conditions Unstable conditions Very unstable conditions
1.2. Application filter
1.2.1 1.2.2
ο Final readout Filling
1.3. Stability range
1.3.1 1.3.2 1.3.3 1.3.4 1.3.5
1/4 digit 1/2 digit 1 digit ο 2 digits 4 digits
1.5. Calib./adjust./linearization: Function of the Q key
1.5.1 1.5.2 1.5.3
ο Calibration/span adjustment Linearization: for service personnel only Key blocked
1.6. Auto zero
1.6.1 1.6.2
ο On Off
1.7. 1st weight unit, or 2nd unit in Toggle Weight Units app.
1.7.1 to 1.7.23
User-defined unit: see “Toggling between Weight Units”
5. and 6.
Only relevant with built-in data interface: see corresponding interface description
8. Additional functions
8.1. Block key functions
8.1.1 8.1.2
All keys blocked except for e and w ο All keys unblocked
8.2. Automatic shut-off
8.2.1 8.2.2 8.2.3
ο After 2 minutes After 5 minutes After 10 minutes
9.1. Factory settings
9.1.1 9.1.2
Restore ο Do not restore
9. Reset menu
16
Press and hold Confirm setting – Save settings and exit Setup
Error Codes
Error codes are shown on the main display for approx. 2 seconds. The program then returns automatically to the previous mode. Display/Problem No segments appear on the display
oL UL
disErr
calErr
appErr
PrtErr Bal.Err
Sys.Err Max. weighing capacity is less than indicated under “Specifications” The weight readout is obviously wrong
Cause No power available
Solution Check the power supply
The AC adapter is not plugged in Battery is drained
Plug in the AC adapter Replace battery; recharge battery using external charger Unload the balance/scale
The load exceeds the balance/scale capacity Weighing pan not in place Something is touching the weighing pan Display overflow: Value cannot be shown on the display Calibration parameter not met; e.g.: – Balance/scale not zeroed – Balance/scale is loaded Weight is too light or there is no sample on the balance/scale with application in use Data interface for printing is blocked Balance/scale loaded or defective when power was turned on
Place the weighing pan on the balance/scale Move the object that is touching the weighing pan Reduce load on the balance/scale Calibrate only when zero is displayed Press w to tare the balance/scale Unload the balance/scale Increase the weight on the balance/scale
Contact the Sartorius customer service center Unload balance/scale before switching on or contact Sartorius customer service Balance/scale defective Contact Sartorius customer service The balance/scale was Place the weighing pan switched on without on the balance/scale and the weighing pan in place press e The balance/scale was not Calibrate/adjust the calibrated/adjusted before weighing balance/scale Balance/scale not zeroed Zero the balance/scale
If any other errors occur, contact your local Sartorius customer service center. 17
Overview
Specifications Model Weighing capacity Readability Tare range (subtractive) Linearity Operating temperature range Stabilization time (average) Adaptation to ambient conditions Calibration weight Net weight, approx. Pan size Power source/voltage/frequency Power consumption (average) Power requirements, DC voltage Hours of operation with battery: – Mignon, AA alkaline manganese (2200 mAh), avg. – Rechargeable 1500 mAh, fully ch., (NiMH), avg. Model Weighing capacity Readability Tare range (subtractive) Linearity Operating temperature range Stabilization time (average) Adaptation to ambient conditions Calibration weight Net weight, approx. Pan size Power source/voltage/frequency Power requirements, DC voltage Power consumption (average) Hours of operation with battery: – Mignon, AA alkaline manganese (2200 mAh), avg. – Rechargeable 1500 mAh, fully ch., (NiMH), avg. * = included in delivery
18
g g <±g s
g kg mm W
GD502 ELT103 ELT602 ELT402 ELT202 500 ct 100 g 600 g 400 g 200 g 0.005 0.001 0.01 0.01 0.01 500 ct 100 g 600 g 400 g 200 g 0.015 ct 0.003 g 0.03 g 0.03 g 0.035 g 10°C to 30°C (273°K to 303°K; 50°F to 86°F) 2.5 2.5 2 2 2 By selection of 1 of 4 optimized filter levels; display update: 0.1–0.8 (depends on filter level selected) 100 (F1)* 100 (F1)* 200 (F2)* 200 (F2)* 100 (F2)* 1.2 1.2 1.35 1.35 1.25 107 d 107 d 140+ 127 140 +127 140 +127 AC adapter, 230 V or 115 V, +15% to –20%, 48–60 Hz 1 1 0.8 0.8 0.8 12 V to 20 V
h
–
–
35
35
35
h
–
–
24
24
24
W
ELT6001 ELT4001 ELT2001 ELT1001 ELT601 ELT6000 6000 4000 2000 1000 600 6000 0.1 0.1 0.1 0.1 0.1 1 6000 4000 2000 1000 600 6000 0.2 0.2 0.2 0.2 0.2 2 10°C to 30°C (273°K to 303°K; 50°F to 86°F) 2 2 2 1.5 1.5 1.5 By selection of 1 of 4 optimized filter levels; display update: 0.1–0.8 (depends on filter level selected) 5 (F2) 2 (F2) 2 (F2) 0,2 (F2)* 0,1 (F2)* 5 (M1) 1.25 1.25 1.25 1.1 1.1 1.1 140+127 AC adapter, 230 V or 115 V, +15% to –20%, 48–60 Hz 12 V to 20 V 0.8 0.8 0.8 0.6 0.6 0.6
h
35
35
35
60
60
60
h
24
24
24
42
42
42
g g g <±g s
kg kg mm
Accessories (Options)
Product Data interface, mounting kit – RS-232 interface with cable – USB interface with cable
– – – –
Order No. YADAP-RS YADAP-USB
Data printer
YDP03-0CE
Lock-down capability (for anti-theft locking device)
LC-1
Calibration weights for ELT6001 (5 kg; F2) for ELT4001/2001 (2 kg; F2) for ELT6000 (5 kg; M1) for weight compartment, (rear side), (100 g; F1) Round glass draft shield (25 mm high)
YCW6548-00 YCW6248-00 YCW655-00 Available on request Available on request
Weighing pan – Round – Rectangular
Available on request Available on request
Pan support – Round – Rectangular
Available on request Available on request
Leveling feet (set of one adjustable foot and one fixed foot)
Available on request
Plug for level indicator port
Available on request
Covers – Battery compartment – Interface port – Below-balance/scale port
Available on request Available on request Available on request
Weight compartment
Available on request
19
C
20
⋡ ᰴ ࡍࠫ ⼊๔ߣోᵈᗧ
3
ోߦ߅ߚߛߊߚߦ
3
⸽ߦߟߡ
3 22 4 22 4 22
ᆎࠆ೨ߦ ᪿ൮ౝኈ ⸳⟎᧦ઙ ᝪઃᚻ㗅 AC 㔚Ḯ߳ߩធ⛯ บਅ߭ࠂ߁㊂ ࡃ࠶࠹ߩขࠅઃߌ ᳓ᐔߩ⺞ᢛ ࠠࡖࡉ࡚ࠪࡦ㧛ࠬࡄࡦ⺞ᢛ↪ಽ㌃ߩขࠅᄖߒ ߭ࠂ߁㊂ᠲ
␜ㇱߩࠠߩ⺑
ၮᧄ߭ࠂ߁㊂
4 23 4 23 5 23 23 5 24 5 24 6 24 6 25 7 25 7
㊀㊂නߩᄌ឵
7 26 26 9 26 9
ࠞ࠙ࡦ࠹ࠖࡦࠣ
10 28
㧑߭ࠂ߁㊂
12 28
ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ
ࡎ࡞࠼␜
29 14
ว⸘
31 15
Ყ㊀᷹ቯ
33 17
ࠠࡖࡉ࡚ࠪࡦ㧛ࠬࡄࡦ⺞ᢛ
34 19
ᄤ߮ࠎߩ᭴ᚑ
21
⸳ቯ㧔࠶࠻ࠕ࠶ࡊࡔ࠾ࡘ㧕 ࡄࡔ࠲৻ⷩ ࠛࠦ࠼
36
38 21 22 40 23 40 24 41
ⷐ
࠹ࠢ࠾ࠞ࡞࠺࠲
24
ࠕࠢࠨ㧔ࠝࡊ࡚ࠪࡦ㧕
27
CE ࡑࠢࠠࡦࠣ
28
SAS ቯᦼᩞᱜࠨࡆࠬߩߏ᩺ౝ
42 43 43 46 47 48
21
⼊๔ߣోᵈᗧ ోߦ߅ߚߛߊߚߦ ߎߩߚ߮ߪࠬ࠙࠻࡞ࠩޔ㔚ሶᄤ߮ࠎ
ELEMENT ࠪ࠭ ࠍ߅⾈ߍߚߛ߈߹ߒߡ
ࠅ߇ߣ߁ߏߑ߹ߔޕ
ᄤ߮ࠎࠍߏ↪ߩ೨ߦޔᔅߕߎߩขᛒ⺑ᦠࠍࠃߊ ߅⺒ߺߊߛߐ߹ߔࠃ߁߅ޔ㗿↳ߒߍ߹ߔޕ
㒐᭴ㅧߢߪࠅ߹ߖࠎߩߢෂ㒾ߥၞ߿႐ᚲߢᄤ߮ࠎࠍ↪ߒߥߢߊߛߐޕ ↪ߔࠆ೨ߦ AC ࠕ࠳ࡊ࠲ߩ␜ߦᓥଏ⛎㔚ߣห৻ߢࠆߎߣࠍ⏕ߒߡߊߛߐޕ 㔚ᳰࠍߏ↪ߩ႐วߪޔᏒ⽼ߩ 1.5V ࠕ࡞ࠞ㔚ᳰࠍߏ↪ߊߛߐޕ ߹ߚޔల㔚ᑼ㔚ᳰ߽↪ߢ߈߹ߔޕ 㧔ઃዻߐࠇߡ߹ߖࠎ㧕 㧙 ᄤ߮ࠎߪ AC ࠕ࠳ࡊ࠲ߦࠃࠅ㔚Ḯߦធ⛯ߐࠇߡࠆ႐วޔ ߅ࠃ߮㔚ᳰ߇ⵝ⌕ߐࠇߡࠆ႐วߪޔ ㅢ㔚⁁ᘒߦߥߞߡ߹ߔޕ 㧙 AC ࠕ࠳ࡊ࠲ߪ㒐᳓ߢߪࠅ߹ߖࠎޕᶧ߇ਛߦࠄߥࠃ߁ߦߒߡߊߛߐޕ ㆊᐲߩ㔚⏛ᵄߦߐࠄߐࠇߥࠃ߁ߦߒߡߊߛߐ⺒ޕข୯ߦᓇ㗀ࠍ߷ߔ႐ว߇ࠅ߹ߔޕૉ ߒޔ㔚⏛ᵄߩᓇ㗀߇ήߊߥࠆߣㅢᏱߦ↪ߢ߈߹ߔޕ 㧙 ࠕࠢࠨ߅ࠃ߮ࠝࡊ࡚ࠪࡦ㘃ߪߩߎޔᄤ߮ࠎߦ↪ߔࠆߚߦᦨㆡߦ࠺ࠩࠗࡦߐࠇߡ߹ ߔࡦ࡚ࠪࡊࠝ߮ࠃ߅ࠨࠢࠕߩࠞࡔߩઁޕ㘃ߪ↪ߒߥߢߊߛߐޕ ᵈ㧦ELEMENT ࠪ࠭ߪޔขᒁ⸽↪ߦࠊࠇࠆ․ቯ⸘㊂ེߣߒߡߪ↪ߢ߈߹ߖࠎޕ
⸽ߦߟߡ 㧙 ᄤ߮ࠎߩࡂ࠙ࠫࡦࠣࠍ㐿ߌߥߢߊߛߐᦼ⸽ޕ㑆ౝߢߞߡ߽ࠢࡓߩኻ⽎ᄖߣߥࠅ߹ ߔߩߢߏᵈᗧߊߛߐޕ 㧙 หᪿߩ⸽ᦠ⊓㍳ࠞ࠼ߦᔅⷐ㗄ࠍߏ⸥ߩߪߚ߹ࢃࠬ࠙࠻ࠩޔᑷ␠ઍℂᐫߦ⊓㍳ࠞ ࠼ࠍߏㅍߊߛߐޕ
22
ᆎࠆ೨ߦ ᆎࠆ೨ߦ ᪿ൮ౝኈ 㧙 ᄤ߮ࠎᧄ ᪿ൮ౝኈ 㧙 ߭ࠂ߁㊂⋁ 㧙 㧙 㧙 㧙
AC ࠕ࠳ࡊ࠲ ᄤ߮ࠎᧄ ࠠࡖࡉ࡚ࠪࡦ↪ಽ㌃ ߭ࠂ߁㊂⋁
ߦߟߡߪࠝࡊ࡚ࠪࡦߣ 㧙 㧔ELT6001㧛ELT4001㧛ELT2001㧛ELT1001㧛ELT601㧛ELT6000 AC ࠕ࠳ࡊ࠲ ߥࠅ߹ߔޕㅜߏᵈᢥߊߛߐޕ 㧕 㧙 ࠠࡖࡉ࡚ࠪࡦ↪ಽ㌃ 㧙 㧔ELT6001㧛ELT4001㧛ELT2001㧛ELT1001㧛ELT601㧛ELT6000 ਣᒻࠟࠬ㘑㒐㧔1mg ࠲ࠗࡊ㧕 ߦߟߡߪࠝࡊ࡚ࠪࡦߣ 㧙 ᳓Ḱེߣ⺞ᢛ↪ࡈ࠶࠻ ߥࠅ߹ߔޕㅜߏᵈᢥߊߛߐޕ 㧕 㧙 ਣᒻࠟࠬ㘑㒐㧔1mg ࠲ࠗࡊ㧕 㧙 ᳓Ḱེߣ⺞ᢛ↪ࡈ࠶࠻
⸳⟎᧦ઙ ᄤ߮ࠎߩ⸳⟎႐ᚲࠍㆬ߱ߣ߈ޔਅ⸥ߩ᧦ઙࠍߏ⏕ߊߛߐޕ ⸳⟎᧦ઙ 㧙 ᄤ߮ࠎࠍࡅ࠲ߩㄭߊߦ⟎ߚࠅ⋥ޔᣣశߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ 㧙 ᄤ߮ࠎࠍ⓹߿࠼ࠕ߆ࠄ᧪ࠆㅢ㘑ߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ ᄤ߮ࠎߩ⸳⟎႐ᚲࠍㆬ߱ߣ߈ޔਅ⸥ߩ᧦ઙࠍߏ⏕ߊߛߐޕ 㧙 ߭ࠂ߁㊂ᠲਛߦᄤ߮ࠎࠍㆊᐲߩᝄേߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ 㧙 ᄤ߮ࠎࠍࡅ࠲ߩㄭߊߦ⟎ߚࠅ⋥ޔᣣశߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ 㧙 㧙 ᄤ߮ࠎࠍ㐳ᤨ㑆Ḩ᳇ߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ ᄤ߮ࠎࠍ⓹߿࠼ࠕ߆ࠄ᧪ࠆㅢ㘑ߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ 㧙 ߭ࠂ߁㊂ᠲਛߦᄤ߮ࠎࠍㆊᐲߩᝄേߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ
ᝪઃᚻ㗅 㧙 ᄤ߮ࠎࠍ㐳ᤨ㑆Ḩ᳇ߦߐࠄߐߥࠃ߁ߦߒߡߊߛߐޕ ᝪઃᚻ㗅
23
24
25
߭ࠂ߁㊂ᠲ ␜ㇱߩࠠߩ⺑
ࠝࡦ㧛ࠝࡈࠠ(ON/OFF) Ԙ AC ࠕ࠳ࡊ࠲↪ᤨ 㨯 ࠝࡦ㧔ࡃ࠶ࠢࠗ࠻ઃ߈㧕/ࠬ࠲ࡦࡃࠗ ԙ 㔚ᳰߢ↪ᤨ
␜ㇱ
ࠝࡦ ࡃ ࠢ
ࠝࡦ ࠝࡈ
TARE ࠠ ᄤ߮ࠎߩࡠὐࠍߣࠅ߹ߔޕ 2 ⑽એ㐳ߒߔࠆߣࠕࡊࠤ࡚ࠪࡦ ࡔ࠾ࡘࠍ㐿߈߹ߔޕ PRINT ࠠ 㨯ශሼ߅ࠃ߮࠺࠲ജ CAL ࠠ
CF ࠠ 㩁㨶㩢㩖㩨㩤㨺㩆㨸㩧㧛⺞ᢛߦ 㨯 ㆬᛯߒߚࡔ࠾ࡘߩ⸳ቯ ↪ 㨯 ࠠ㧙߇ 2 ⑽એߐࠇߚ႐วߩࡦ࡚ࠪࠤࡊࠕޔ ⚳ੌߤߥޔ
㧲ࠠ ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓߩ㐿ᆎ ࡔ࠾ࡘߩㆬᛯ
ၮᧄ߭ࠂ߁㊂ ․ᓽ 㧙 ᄤ߮ࠎߩࡠὐ⺞ᢛ ో߭ࠂ߁㊂▸࿐ߦᷰߞߡࡠὐ⺞ᢛ߇ߢ߈߹ߔޕ Ḱ ٨ ᄤ߮ࠎߩࠬࠗ࠶࠴ࠝࡦ㧦ࠝࡦ㧛ࠝࡈࠠ㧔ON/OFF㧕ࠍߒ߹ߔޕ ٨ ࠹ࠕࠠ(TARE)ࠍߒߡߊߛߐޕ ٤ ᔅⷐߦᔕߓߡᄤ߮ࠎߩฦ⒳⸳ቯࠍᄌᦝߒߡߊߛߐޕ 㧔 ̌ᄤ߮ࠎߩ᭴ᚑ̍ߩ㗄ࠍෳᾖ㧕 ٤ ᔅⷐߦᔕߓߡᄤ߮ࠎߩ⸳ቯࠍ̌Ꮏ႐⩄ᤨ⸳ቯ̍ߦᚯߒߡߊߛߐޕ 㧔ࡔ࠾ࡘࠍ ̌9.-1̍ߦ⸳ቯߔࠆ㧕
26
e
w
27
ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ ㊀㊂නߩᄌ឵ ߎߩࠕࡊࠤ࡚ࠪࡦߢߪޔ2 ⒳㘃ߩ㊀㊂න㑆ߢ߭ࠂ߁㊂୯ߩ␜ࠍಾࠅ឵߃ࠄࠇ߹ߔޕ ࡔ࠾ࡘࠦ࠼
1. user*
㊀㊂න
ᄌ឵ቯᢙ
ࠣࡓ
1.00000000000
ࠣࡓ**
1.00000000000
ࠞ࠶࠻
5.00000000000
࠾ࡘ࠻ࡦ
0.00980665000
␜
2.grams
*㧩RS232 ߹ߚ US㧮ߩࡊࡠࠣࡓ㧔ࠝࡊ࡚ࠪࡦ㧕ߢᔅⷐߦࠃࠅ࡙ࠩ⸳ቯ߇น⢻ޕ
4.cart
**㧩Ꮏ႐⩄ᤨ⸳ቯ
23.newt ⸥㊀㊂නએᄖߪᣣᧄ࿖ౝߢߪ↪ߢ߈߹ߖࠎޕ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ
TARE ࠠࠍ
ߩㆬᛯߒߡߊߛߐޕ
2 ⑽એߔ
2. ㊀㊂නߩᄌ឵ࠍㆬᛯ
㧲ࠠࠍߔ
␜
ߒߡߊߛߐޕ 3. ㆬᛯߒߚ㊀㊂නߩ⏕
CF ࠠࠍߔ
ࠍߒߡߊߛߐޕ 4. ㊀㊂නࠍㆬᛯߒߡ ߊߛߐޕ
㧲ࠠ 㧔ฝߩ␜߇ࠆ߹ߢ
㧔4.ߩࠞ࠶࠻ࠍㆬᛯ㧕 5. ㊀㊂නߩ⏕
➅ࠅߒߡߔ㧕 CF ࠠࠍߔ
ࠍߒߡߊߛߐޕ
ߡߊߛߐޕ
28
•†• ⁕ ‧••†•⁕
6. ߭ࠂ߁㊂⋁ߦࠨࡦࡊ࡞ࠍタߖ
7. ㊀㊂නߩᄌ឵ࠍߒ߹ߔޕ
…†‵ ⊕″
㧲ࠠࠍߔ
ࠞ࠙ࡦ࠹ࠖࡦࠣ ࠞ࠙ࡦ࠹ࠖࡦࠣࡊࡠࠣࡓߢߪ߷߶ޔห╬ߩන㊀ࠍ߽ߟㇱຠߩᢙ㊂ࠍቯߢ߈߹ߔޕ 㧦ෳᾖᢙࠍ⸳ቯߒᧂޔ⍮ߩᢙࠍ⸘▚ߒ߹ߔޕ 㧔ෳᾖᢙ㧦20 㧕 ᠲ
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ ࠍㆬᛯߒߡߊߐߛޕ
2. ࠞ࠙ࡦ࠹ࠖࡦࠣࠍㆬᛯ ߒߡߊߐߛޕ
3. ࠞ࠙ࡦ࠹ࠖࡦࠣࠍ⏕
ࠠ㧔߹ߚߪᚻ㗅㧕
␜
TARE ࠠࠍ 2 ⑽ એߔ
F ࠠࠍ➅ߒ ߔ
CF ࠠࠍߔ
ߒߡߊߐߛޕ ␜ㇱߦ 㧖 ߇␜ߐࠇ߹ߔޕ
4. ߭ࠂ߁㊂⋁ߦⓨߩኈེ ࠍ⟎ߡߊߛߐޕ
5. ᄤ߮ࠎߩࡠὐࠍߣࠅ߹ߔޕ
TARE ࠠࠍߔ
6. ෳᾖᢙ㧦20 ࠍ ኈེߦࠇ߹ߔޕ
7. ෳᾖᢙࠍㆬᛯߒ߹ߔޕ 1-99 ߪߚ߹ޔ10 ߕߟᓴⅣ
㧲ࠠࠍ➅ߒߔ߆ߪߚ߹ޔ
ߒ߹ߔޕ 㧔ဳᑼߦࠃࠆ㧕
㧲ࠠࠍ 2 ⑽એߔ
8. ෳᾖᢙࠍ⏕ߒ߹ߔޕ
9
CF ࠠࠍߔ
⸘㊂ߔࠆࠨࡦࡊ࡞ࠍ ࠇ߹ߔޕ
29
30
㧑߭ࠂ߁㊂ 㧑߭ࠂ߁㊂ࡊࡠࠣࡓߢߪޔෳᾖ߭ࠂ߁㊂ߦኻߔࠆ㧑ߢ߭ࠂ߁㊂⺒ข୯ࠍ␜ߢ߈߹ߔޕ 㧦ෳᾖ߭ࠂ߁㊂ߦኻߔࠆ㧑ߢ߭ࠂ߁㊂୯ࠍ␜ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ ࠍㆬᛯߒߡߊߐߛޕ
2. 㧑߭ࠂ߁㊂ࠍㆬᛯߒߡ ߊߐߛޕ
3. 㧑߭ࠂ߁㊂ࠍ⏕ߒߡߊ
␜
TARE ࠠࠍ 2 ⑽ એߔ
F ࠠࠍ➅ߒ ߔ
CF ࠍߔ
ߊߛߐޕ ␜ㇱߦ 㧖 ߇␜ߐࠇ߹ߔޕ
4.
߭ࠂ߁㊂⋁ߦⓨߩኈེ ࠍ⟎ߡߊߛߐ
5. ᄤ߮ࠎߩࡠὐࠍߣࠅ߹ߔޕ
TARE ࠠࠍߔ
6. ෳᾖ㧑ߣห╬ߩ 100㧑ࠨࡦࡊ࡞ࠍ ኈེߦࠇ߹ߔ
7. F ࠠࠍߔߎߣߦࠃࠅዊᢙὐ
㧲ࠠࠍ➅ߒߔ
એਅߩ␜߇น⢻ߦߥࠅ߹ߔޕ
100.0㧑ޔ100.00㧑߹ߚߪ 100㧑㧔Ꮏ႐⩄ᤨ⸳ቯ㧕 8. ዊᢙὐߩ⟎ࠍ⏕ߒ߹ߔޕ
CF ࠍߔ
9. ⸘㊂ߔࠆࠨࡦࡊ࡞ࠍ ࠇ߹ߔޕ
31
32
ࡎ࡞࠼␜ ࡎ࡞࠼␜ࠕࡊࠤ࡚ࠪࡦߢߪ߁ࠂ߭ࠍ࡞ࡊࡦࠨޔ㊂⋁߆ࠄขࠅ㒰ߚ႐วߢ߽ޔ5 ⑽㑆ߘߩ ୯ࠍ␜ߒ⛯ߌ߹ߔޕ 㧦⋁ࠃࠅᄢ߈ߥࠨࡦࡊ࡞ߩ߭ࠂ߁㊂୯ߩ᷹ቯߥߤ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ ࠍㆬᛯߒߡߊߐߛޕ
2. ࡎ࡞࠼␜ࠍㆬᛯߒߡ ߊߐߛޕ
3. ࡎ࡞࠼␜ࠍ⏕ߒߡߊߛߐޕ
␜
TARE ࠠࠍ 2 ⑽ એߔ
F ࠠࠍ➅ߒ ߔ
CF ࠠࠍߔ
␜ㇱߦ 㧖 ߇␜ߐࠇ߹ߔޕ
4. ᔅⷐߦᔕߓߡࡠὐࠍߣߞߡ
TARE ࠠࠍߔ
ߊߛߐޕ
5. ߭ࠂ߁㊂⋁ߦࠨࡦࡊ࡞ࠍ ⟎ߡߊߛߐ
6. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ
F ࠠࠍߔ
ࠍ㐿ᆎߒ߹ߔޕ ߇ὐṌߒ߁ࠂ߭ޔ㊂୯ߪࡠ࠶ࠢߐࠇ߹ߔޕ
7. ࠨࡦࡊ࡞ࠍ㒠ࠈߒ߹ߔޕ ߭ࠂ߁㊂୯ߪ 5 ⑽㑆␜ߐࠇ߹ߔޕ
8.
ࡠὐࠍߣߞߡߊߛߐޕ
9.
ࠕࡊࠤ࡚ࠪࡦߩ⚳ੌ
10. ߎߩࠕࡊࠤ࡚ࠪࡦࠍ⛯ߌࠆ႐ว
TARE ࠠࠍߔ CF ࠠࠍ 2 ⑽એߔ 㧲ࠠࠍߔ
㧔ઁߩࠕࡊࠤ࡚ࠪࡦߦᄌᦝߒߡߥ႐ว㧕
11. 5.ࠃࠅ➅ࠅߒߡߊߛߐ
33
ว⸘ ว⸘ࠕࡊࠤ࡚ࠪࡦߢߪࠅ߆ߪࠍ࡞ࡊࡦࠨߩ߆ߟߊޔㄟߎߣ߇ߢ߈߹ߔޕ 㧦ࠨࡦࡊ࡞ߩว⸘୯ߩ␜ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ
TARE ࠠࠍ 2 ⑽
ࠍㆬᛯߒߡߊߐߛ ޕ
એߔ
2. ว⸘ࠕࡊࠤ࡚ࠪࡦࠍ
F ࠠࠍ➅ߒ
ㆬᛯߒߡߊߐߛ ޕ
ߔ
3. ว⸘ࠕࡊࠤ࡚ࠪࡦࠍ
CF ࠠࠍߔ
␜
⏕ߒߡߊߛߐޕ ␜ㇱߦ 㧖 ߇␜ߐࠇ߹ߔޕ
8. ᔅⷐߦᔕߓߡࡠὐࠍߣߞߡ
TARE ࠠࠍߔ
ߊߛߐޕ
5. ߭ࠂ߁㊂⋁ߦࠨࡦࡊ࡞ࠍ ⟎ߡߊߛߐޕ 㧔ߎߩߢߪ 380㨓)
6. ࡔࡕߦ୯ࠍሽߒ߹ߔ ޕ
CF ࠠࠍߔ
ว⸘୯߇␜ߐࠇ߹ߔޕ ߇ὐṌߒ߹ߔޕ
7. ࠨࡦࡊ࡞ࠍ㒠ࠈߒ߹ߔ ޕ
8. ᰴߩࠨࡦࡊ࡞ࠍ⟎߈߹ߔ ޕ 㧔ߎߩߢߪ 575㨓)
9.
ࡔࡕߦ୯ࠍሽߒ߹ߔ ޕ
CF ࠠࠍߔ
ว⸘୯߇␜ߐࠇ߹ߔޕ ߇ὐṌߒ߹ߔޕ ᵈ㧦ࡔࡕߦሽߐࠇߚ୯߇ࠢࠕߐࠇࠆ߹ߢ
34
ߪ␜ߐࠇߡ߹ߔޕ
35
Ყ㊀᷹ቯ ߎߩࠕࡊࠤ࡚ࠪࡦߢߪߩ࡞ࡊࡦࠨޔᲧ㊀ࠍ᷹ቯߒ߹ߔޕዊᢙὐએਅ 1 ߹ߢ␜ߒ߹ߔࡆޕ ࠞ߅ࠃ߮ࡢࠗࡗߪ߹ࠇߡ߹ߖࠎޕㅜߏ↪ᗧߊߛߐޕ 㧦࿕ߩᲧ㊀ߩ᷹ቯ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ࠕࡊࠤ࡚ࠪࡦࡊࡠࠣࡓ
TARE ࠠࠍ 2 ⑽
ࠍㆬᛯߒߡߊߐߛޕ
એߔ
2. Ყ㊀᷹ቯࠕࡊࠤ࡚ࠪࡦ
F ࠠࠍ➅ߒ
ࠍㆬᛯߒߡߊߐߛޕ
3.
ߔ
CF ࠠࠍߔ
Ყ㊀᷹ቯࠕࡊࠤ࡚ࠪࡦ ࠍ⏕ߒߡߊߛߐޕ ␜ㇱߦ 㧖 ߇␜ߐࠇ߹ߔޕ
4. ᔅⷐߦᔕߓߡࡠὐࠍߣߞߡ
TARE ࠠࠍߔ
ߊߛߐޕ
5. ࠕࡊࠤ࡚ࠪࡦࠍ
F ࠠࠍߔ
㐿ᆎߒ߹ߔޕ
6.
CF ࠠࠍߔ
ࠍ⏕ߒ߹ߔޕ
7. ⓨ᳇ਛߢߩࠨࡦࡊ࡞ߩ㊀㊂୯᷹ቯߒ߹ߔޕ ߭ࠂ߁㊂⋁ߩߦࠨࡦࡊ࡞ࠍ⟎߈߹ߔޕ
8. ㊀㊂୯ࠍሽߒ߹ߔޕ 9. ߭ࠂ߁㊂⋁߆ࠄࠨࡦࡊ࡞ ࠍ㒠ࠈߒ߹ߔޕ
10. ᶧਛߩ㊀㊂୯ࠍ᷹ቯߒ߹ߔޕ ࡢࠗࡗߦࠨࡦࡊ࡞ࠍษࠅਅߍ߹ߔޕ
36
CF ࠠࠍߔ
␜
37
ࠠࡖࡉ࡚ࠪࡦ㧛ࠬࡄࡦ⺞ᢛ ᄤ߮ࠎࠍᦨೋߦ⸳⟎ߒߚߣ߈ߪߚ߹ޔ⒖േߒߚߣ߈ߪࠠࡖࡉ࡚ࠪࡦ㧛⺞ᢛࠍⴕߞߡߊߛߐޕ ․ᓽ㧦ࠠࡖࡉ࡚ࠪࡦ㧛⺞ᢛߪਅ⸥ߩ႐วߦⴕߞߡߊߛߐޕ 㧙 ᄤ߮ࠎߩ߭ࠂ߁㊂⋁ߦ߽タߖߡߥߣ߈ 㧙 ᄤ߮ࠎߩࡠὐ߇ߣࠇߡࠆߣ߈ 㧙 ౝㇱାภ߇ቯߒߡࠆߣ߈ ⸥ߩ⁁ᘒߦߥ႐วޔᄤ߮ࠎߪࠛࡔ࠶ࠫࠍ␜ߒ߹ߔޕ ࠠࡖࡉ࡚ࠪࡦ㧛⺞ᢛ↪ߩಽ㌃୯߇␜ߐࠇ߹ߔޕಽ㌃ߦߟߡߪޔ ̌ࠠࡖࡉ࡚ࠪࡦ㧛 ࠬࡄࡦ⺞ᢛ↪ಽ㌃ߩขࠅᄖߒ̍ߩ㗄ࠍߏෳᾖߊߛߐ㧔ဳᑼߦࠃࠆ㧕 ޕ ⇣ߥߞߚಽ㌃୯ߩㆬᛯߦߪޔ㧲ࠠࠍ↪ߒ߹ߔޕ ㅜਛߢᚻ⛯߈ࠍขࠅᶖߔ႐วߪޔCF ࠠࠍ 2 ⑽એߒߡߊߛߐޕ 㧦 ELT6001 ߩࠠࡖࡉ࡚ࠪࡦ㧛⺞ᢛ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ᄤ߮ࠎࠍࠝࡦߒ߹ߔ ޕ
ON/OFF ࠠࠍߔ
2. ᄤ߮ࠎߩ TARE ὐࠍ
TARE ࠠࠍߔ
ߣࠅ߹ߔޕ CAL ࠠࠍߔ
3. ࠠࡖࡉ࡚ࠪࡦࠍ 㐿ᆎߒ߹ߔޕ ㊀㊂නߥߒߢޔಽ㌃ ߩ୯߇␜ߐࠇ߹ߔޕ 㧔ߎߩߢߪޔ5000g㧕
4. ઁߩಽ㌃୯ࠍㆬᛯߒߡ ߊߛߐ ޕ
F ࠠࠍ➅ߒ
ߔ
5. ಽ㌃୯ࠍ⏕ߒࡦ࡚ࠪࡉࡖࠠޔ㧛 CF ࠍߔ ࠬࡄࡦ⺞ᢛࠍ㐿ᆎߒ߹ߔޕ ࡠὐ߇ሽߐࠇߚߣޔ ࠠࡖࡉ࡚ࠪࡦಽ㌃୯߇ ␜ㇱߦὐṌߒ߹ߔޕ
38
␜
ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
␜
6. ߭ࠂ߁㊂⋁ߦಽ㌃ࠍ タߖ߹ߔޕ ಽ㌃߇ᤨ㑆ౝߦ⟎߆ࠇࠆߣ ⺒ข୯ߩὐṌ߇ᱛ߹ࠅቯߒ߹ߔޕ ಽ㌃୯߇ ok ߢࠆߣὐṌߪᱛ߹ࠅ ቯൻࠪࡦࡏ࡞ߩ ࡑࠢ߇␜ߐࠇ߹ߔޕ
7. ಽ㌃ࠍ㒠ࠈߒߡߊߛߐޕ
8. ࠠࡖࡉ࡚ࠪࡦ߇ቢੌߒ߹ߒߚޕ
39
ᄤ߮ࠎߩ᭴ᚑ ⸳ቯ㧔࠶࠻ࠕ࠶ࡊࡔ࠾ࡘ㧕 ฦ⒳ࡔ࠾ࡘߩ⸳ቯߦࠃࠅⷐߩޘ᳞ߦวߞߚᄤ߮ࠎࠍ᭴ᚑߔࠆߎߣ߇ߢ߈߹ߔޕ ᠲ
ࠠ㧔߹ߚߪᚻ㗅㧕
1. ᄤ߮ࠎࠍࠝࡈߒߡߊߛߐޕ
␜
ON/OFF ࠠࠍ ߔ
2. ᄤ߮ࠎࠍࠝࡦߒߡߊߛߐޕ
ON/OFF ࠠࠍ ߔ
ߔߴߡߩࠣࡔࡦ࠻߇␜
TARE ࠠࠍ
ߐࠇߡࠆ㑆ߦ
ߔ
࠶࠻ࠕ࠶ࡊࡔ࠾ࡘ ࠠ
CF
シߊߔ ࡔ࠾ࡘࡌ࡞㧦ฝᣇะߦ⒖േ㧔ࠨࠗࠢ࡞㧕
ߒ⛯ߌࠆ ⸳ቯߩ⏕
F
ࡔ࠾ࡘ㗄⋡㧦 ᓴⅣ
㧙
TARE
ࡔ࠾ࡘࡌ࡞㧦Ꮐᣇะߦ⒖േ
⸳ቯߩሽߣ⸳ቯߩ⚳ੌ
40
41
ࠛࠦ࠼ ࠛࠦ࠼ߪ␜ㇱߦ⚂㧞⑽㑆␜ߐࠇ߹ߔߩߘޕᓟ⥄േ⊛ߦ೨ߩ⁁ᘒߦᚯࠅ߹ߔޕ ࠛࠦ࠼㧛
ේ࿃
ࡔ࠶ࠫ␜
ಣ⟎
␜ㇱߦ߽
AC 㔚Ḯߪߞߡߥ
AC 㔚Ḯࠍ࠴ࠚ࠶ࠢߔࠆ
␜ߐࠇߥ
AC ࠕ࠳ࡊ࠲߇ធ⛯ߐࠇߡߥ
AC ࠕ࠳ࡊ࠲ࠍធ⛯ߔࠆ
ࡃ࠶࠹߇ᶖ⠻ߒߡࠆ
ࡃ࠶࠹ߩ឵ߪߚ߹ޔ ల㔚ߔࠆ
⩄㊀߇ᄤ߮ࠎߩ߭ࠂ߁㊂▸࿐ࠍ ߃ߡࠆ
߭ࠂ߁㊂⋁߆ࠄࠨࡦࡊ࡞ࠍ㒠ࠈߒ ߡߊߛߐޕ
߭ࠂ߁㊂⋁߇࠶࠻ߐࠇߡߥ
߭ࠂ߁㊂⋁ࠍ࠶࠻ߔࠆ
߆߇߭ࠂ߁㊂⋁ߦ⸅ࠇߡࠆ
⸅ࠇߡࠆ߽ߩࠍขࠅ㒰ߡߊ
␜ࠝࡃࡈࡠ㧦
ᄤ߮ࠎߩ⩄㊀ࠍᷫߓࠆ
ߛߐ ୯߇␜ㇱߦ␜ߐࠇߥ 㩁㨶㩢㩖㩨㩤㨺㩆㨸㩧㧛⺞ᢛߩ᧦ઙ߇วࠊߥ ࡠὐࠍߣߞߡ߆ࠄ㩁㨶㩢㩖㩨㩤㨺㩆㨸㩧ࠍⴕ 㧙ᄤ߮ࠎߩࡠὐ߇ߣࠇߡߥ 㧙߭ࠂ߁㊂⋁ߦߥߦ߆߇タߞߡࠆ
ߞߡߊߛߐ TARE ࠠࠍߒޔᄤ߮ࠎࠍ࠹ࠕߒ ߡߊߛߐ ߭ࠂ߁㊂⋁߆ࠄࠨࡦࡊ࡞ࠍ㒠ࠈߒ ߡߊߛߐ
㊀㊂୯߇シߔ߉ࠆ߆ޔ㨻㩖㩩㩢㩃㨺㩆㨸㩧↪
߿ࠅ⋥ߒߡߊߛߐޕ
ߩࠨࡦࡊ࡞߇߭ࠂ߁㊂⋁ߦタߞߡ ߥ ࡊࡦ࠻↪ߩࠗࡦ࠲ࡈࠚࠬ߇ࡉ ߅⾈ߍߩ⽼ᄁᐫ߹ߚߪࠩ࡞࠻ ࡠ࠶ࠢߐࠇߡࠆ ᦨᄢ߭ࠂ߁㊂߇ ࠹ࠢ࠾ࠞ࡞࠺
߭ࠂ߁㊂⋁ࠍ࠶࠻ߔࠆ೨ߦᄤ߮ ࠎߩࠬࠗ࠶࠴ࠝࡦࠍߒߚ
࠙ࠬࢃߦߏㅪ⛊ߊߛߐ ߭ࠂ߁㊂⋁ࠍ࠶࠻ߒߡ߆ࠄ㔚Ḯࠍ ࠝࡦߔࠆ
࠲ߦ⸥タߐࠇߡ ࠆᢙ୯ࠃࠅዋ ߥ ߭ࠂ߁㊂୯߇ ߈ࠄ߆ߦ㑆㆑ߞ ߡࠆ
߭ࠂ߁㊂೨ߦ㩁㨶㩢㩖㩨㩤㨺㩆㨸㩧㧛⺞ᢛ߇
㩁㨶㩢㩖㩨㩤-㩆㨸㩧㧛⺞ᢛࠍߔࠆ
ߐࠇߡߥ߆ߞߚ ࡠὐ߇ขࠇߡߥ߆ߞߚ
ᄤ߮ࠎߩࡠὐࠍߣࠆ
*⸥એᄖߩࠛߩ႐วߪ߅ߦࢃࠬ࠙࠻࡞ࠩޔวࠊߖߊߛߐޕ
42
ⷐ ࠹ࠢ࠾ࠞ࡞࠺࠲ ဳᑼ
ELT103
߭ࠂ߁㊂
㨓
100
⺒ข㒢ᐲ
㨓 0.001
࠹ࠕ▸࿐ 㧔ᷫ▚ᑼ㧕
㨓
➅ߒᕈ ҇r㨓
100 0.001
⋥✢ᕈ
҇r㨓
0.003
ᠲ᷷ᐲ▸࿐
͠
10㨪30
㨟
2.5
ቯᚲⷐᤨ㑆 㧔ᐔဋ㧕
Ⓧಽᤨ㑆 (㩍㩨㨲㩆㩨㩊㩣㩖㨲㩣㩊)
㧠Ბ㓏ㆬᛯน⢻
(ㆬᛯⓍಽᤨ㑆ߦࠃࠆ)
0.1㨪0.8 ㆬᛯน⢻
ᄖㇱᩞᱜ↪ಽ㌃୯ 㨓
100㧔㧲1㧕
ᱜ㊀㊂ ⚂ޔkg
1.2
␜㩆㨺㩃㩧㩇
߭ࠂ߁㊂⋁ኸᴺ mm 107Ǿ 㔚Ḯ㔚
AC ࠕ࠳ࡊ࠲ޔ115㨂߹ߚߪ 230㨂ޔ+15㧑㨪-20㧑
㔚Ḯᵄᢙ 48㨪60㧴z ᶖ⾌㔚ജ㧔ᐔဋ୯㧕 㨃
1
㧖᭽ߪ߅ᢿࠅߥߒߦᄌᦝߐߖߡߚߛߊ႐ว߇ࠅ߹ߔޕ
43
ELT602
ELT402
ELT202
ELT6001
ELT4001
ELT2001
ࡥࡺ࠹㔖
㹜
600
400
200
6,000
4,000
2,000
ㄖཱི㝀ᗐ
㹜
0.01
0.01
0.01
0.1
0.1
0.1
2,000
ᆵᘟ
ࢷ⠂ᅑ 600
400
200
6,000
4,000
⧖㏁ࡊᛮ ӌs㹜
0.01
0.01
0.01
0.1
0.1
0.1
├⥲ᛮ
ӌs㹜
0.03
0.03
0.035
0.2
0.2
0.2
᧧షῺᗐ⠂ᅑ
Υ
10㹳30
㹨
2
2
2
2
2
2
㸝΅⟤ᘟ㸞
㹜
Ꮽᏽᡜこ㛣 㸝ᖲᆍ㸞
✒ฦ㛣 (㺘㺳㹽㺑㺳㺕㺮㺡㹽㺮㺕)
4 ṹ㝭㐽ᢝྊ⬗
⾪♟㺑㺅㺎㺲㺒 (㐽ᢝ✒ฦ㛣࡞ࡻࡾ)
0.1㹳0.8 㐽ᢝྊ⬗
አ㒂ᰧḿ⏕ฦ㖙ೋ
200g((F1)
ḿ㔔㔖ࠉ⣑
kg
1.35
ࡥࡺ࠹㔖⓸ᑇἪ
mm
140ə127
200g((F1) 100g((F1) 1.35
1.25
5kg((F1)
2kg(F1)
2kg(F1)
1.25
1.25
1.25
㞹″࣬㞹ᅸ
AC ࢱࣈࢰࠉ115㹋ࡱࡒࡢ 230㹋ࠉ+15㸚㹳-20㸚
㞹″࿔ἴᩐ
48㹳60Hz
ᾐ㈕㞹ງ㸝ᖲᆍೋ㸞
W
0.8
0.8
0.8
0.8
0.8
0.8
21
21
21
21
21
21
14
14
14
14
14
14
㞹ờ࡞ࡻࡾ㸝༟ 8 ᮇ㸞 ⏕㛣 ࣬ࣜ࢜ࣛ㞹ờ㸝⣑㸞㹝 ࣬ ඖ㞹ᘟ㞹ờࠉ ࣆࣜඖ㞹 㸝㹃iMH㸞ᖲᆍ 㹝
㸟 ᵕࡢ࠽᩷ࡽࡊ࡞ን᭞ࡈࡎ࡙࠷ࡒࡓࡂሔྙ࠵ࡽࡱࡌࠊ
44
ELT1001
ELT601
ELT6000
ࡥࡺ࠹㔖
㹜
1,000
600
6,000
ㄖཱི㝀ᗐ
㹜
0.1
0.1
1
ᆵᘟ
ࢷ⠂ᅑ 㸝΅⟤ᘟ㸞
㹜
1,000
600
6,000
⧖㏁ࡊᛮ
ӌs㹜
0.1
0.1
1
0.2
2
├⥲ᛮ
ӌs㹜
0.2
᧧షῺᗐ⠂ᅑ
Υ
10㹳30
㹨
1.5
Ꮽᏽᡜこ㛣 㸝ᖲᆍ㸞
✒ฦ㛣 (㺘㺳㹽㺑㺳㺕㺮㺡㹽㺮㺕)
4 ṹ㝭㐽ᢝྊ⬗
⾪♟㺑㺅㺎㺲㺒 (㐽ᢝ✒ฦ㛣࡞ࡻࡾ)
0.1㹳0.8 㐽ᢝྊ⬗
አ㒂ᰧḿ⏕ฦ㖙ೋ
200g((F1)
100㹜㸝㸻1㸞
5kg((F1)
ḿ㔔㔖ࠉ⣑ kg
1.1
1.1
1.1
ࡥࡺ࠹㔖⓸ᑇἪ mm
142ə127
㞹″࣬㞹ᅸ
AC ࢱࣈࢰࠉ115㹋ࡱࡒࡢ 230㹋ࠉ+15㸚㹳-20㸚
㞹″࿔ἴᩐ
48㹳60㸽z
ᾐ㈕㞹ງ㸝ᖲᆍೋ㸞 㹌
0.6
36
36
㞹ờ࡞ࡻࡾ㸝༟ 8 ᮇ㸞 ⏕㛣 ࣬ࣜ࢜ࣛ㞹ờ㸝⣑㸞㹝
36
࣬ ඖ㞹ᘟ㞹ờࠉ ࣆࣜඖ㞹 㸝㹃iMH㸞ᖲᆍ 㹝
25 25 25
㸟ᵕࡢ࠽᩷ࡽࡊ࡞ን᭞ࡈࡎ࡙࠷ࡒࡓࡂሔྙ࠵ࡽࡱࡌࠊ
45
ࠕࠢࠨ㧙㧔ࠝࡊ࡚ࠪࡦ㧕 ຠ ᵈᢥ⇟ภ ࠺࠲ࠗࡦ࠲ࡈࠚࠬ 㧙 RS-232 ࠗࡦ࠲ࡈࠚࠬ㧔ࠤࡉ࡞ઃ߈㧕
YADAP-RS
㧙 USB ࠗࡦ࠲ࡈࠚࠬ㧔ࠤࡉ࡞ઃ߈㧕
YADAP-UB
࠺࠲ࡊࡦ࠲
YDP03-0CE
㍤ઃࠤࡉ࡞
LC-1
ާ⋑㔍㒐ᱛ↪ި ᩞᱜ↪ಽ㌃ 㧙 ELT6001 㧔5kg;F1㧕
YCW6538-00
㧙 ELT4001 㧔2kg; F1㧕
YCW6238-00
㧙 ELT2001 㧔1kg; F1㧕
YCW6138-00
㧙 ELT6000 (5kg; F1)
YCW6538-00
ਣᒻࠟࠬ㘑㒐㧔㜞ߐ 25mm㧕㧛߭ࠂ߁㊂⋁㧛ࡄࡦࠨࡐ࠻㧛ࡌࡦࠣࡈ࠶࠻㧛 ߘߩઁࠕࠢࠨ㧙ޔㇱຠ㘃ߦߟߡߪ߅วࠊߖߊߛߐޕ
46
CE ࡑࠠࡦࠣ ⵝ⟎ߦᷝઃߐࠇߚ CE ࡑࠠࡦࠣߪᰴߩᜰߦㆡวߒߚⵝ⟎ߢࠆߎߣࠍ␜ߒߡ߹ߔޕ
ᆔຬળᜰ 89/336EEC㧔㔚⏛᳇ㆡวᕈ EMC㧕 ㆡ↪ߐࠇࠆ࡛ࡠ࠶ࡄᮡḰ㧦 ᅹኂᵄߩ⊒↢㒢㧦 ຠᮡḰ EN61326-1 ࠢࠬ 㧮㧔ቛၞ㧕 ᅹኂᵄߦኻߔࠆᛶ᛫ജ㧦 ຠᮡḰ EN61326-1 㧔ᦨዊ࠹ࠬ࠻ⷐ᳞, 㕖ㅪ⛯ᠲ㧕 ㊀ⷐ㗄㧦 ࠕࠠࡘࡏᄤ߮ࠎߩᡷㅧ߅ࠃ߮ࠕࠠࡘࡏຠߢߥࠤࡉ࡞㘃߹ߚߪⵝ⟎ߣߩធ⛯ߦߟߡߪޔ ࠩ࡞࠻࠙ࠬࢃߦ߅วࠊߖߊߛߐޕ
73/22/EEC ૐ㔚ᜰ ㆡ↪ߐࠇࠆ࡛ࡠ࠶ࡄᮡḰ㧦 㧙 㔚᳇ᬺౕེ㧛ᛛⴚౕེߩోᕈ㧦 EN 60950 㧙 ᷹ቯ▤ޔℂߩߢࡏޔ㔚᳇ౕེߩోᕈ㧦 EN61010 ╙ 1 㗄㧦৻⥸ⷐ᳞ ⵝ⟎ߩਛߢ߹ߚࠅࠃޔ㜞ోᮡḰࠍⷐ᳞ߔࠆⅣႺ᧦ઙਅߢ㔚ሶᯏེࠍ↪ߔࠆ႐วޔ ฦ࿖ߩㆡ↪ⷙߦቯࠄࠇߚⷙቯߦᓥ߁ᔅⷐ߇ࠅ߹ߔޕ
2005/9se
47
48
Sartorius AG Weender Landstrasse 94–108 37075 Goettingen, Germany Phone +49.551.308.0 Fax +49.551.308.3289 www.sartorius-mechatronics.com Copyright by Sartorius AG, Goettingen, Germany. All rights reserved. No part of this publication may be reprinted or translated in any form or by any means without the prior written permission of Sartorius AG. The status of the information, specifications and illustrations in this manual is indicated by the date given below. Sartorius AG reserves the right to make changes to the technology, features, specifications and design of the equipment without notice. Status: May 2008, Sartorius AG, Goettingen, Germany
本 社／〒 140-0001 東京都品川区北品川1-8-11 ダヴィンチ品川 II 4F
TEL. (03) 3740-5408
FAX.（03） 3740-5406
技術サービスセンター／〒140-0002 東京都品川区東品川4-13-34 タカセ PDセンター 3F
TEL. (03) 5796-0401
FAX. (03) 3474-8043
JCSS校正室／〒168-0074 東京都杉並区上高井戸1-14-4 三幸ビル2F
TEL. (03) 5316-1555
FAX. (03) 3304-0308
大 阪／〒 532-0003 大阪市淀川区宮原4-3-39 大広新大阪ビル 3F
TEL. (06) 6396-6682
FAX. (06) 6396-6686
名古屋／〒461-0002 名古屋市東区代官町35-16 第一富士ビル6F
TEL. (052) 932-5460
FAX. (052) 932-5461
W4A000 · KT Publication No.: WEL6002-bg08055
