Transcript
Diamond Aircraft Industries GmbH N. A. Otto-Straße 5 2700 Wiener Neustadt Austria
DAI OSB 42NG-042 Page 1 of 3 26-Sep-2014
OPTIONAL SERVICE BULLETIN OSB 42NG-042 I
TECHNICAL DETAILS
I.1
Category Optional.
I.2
Airplanes affected Type:
DA 42 NG, DA 42 M-NG
Serial numbers:
42.N001 and subsequent 42.NC001 and subsequent 42.MN001 and subsequent Airplanes converted to DA 42 NG and DA 42 M-NG
I.3
Date of effectivity 26-Sep-2014
I.4
Time of Compliance At owner’s discretion
I.5
Subject Installation of Provisions for Operation with Diesel fuel. ATA-Code:
I.6
71-00
Reason This Service Bulletin describes the necessary provisions for Operation with Diesel fuel.
I.7
Concurrent Documents None.
I.8
Approval The technical information or instructions contained in this document relate to the Design Change Advisory No. OÄM 42-251, which has been approved under the authority of EASA Design Organization Approval ref. EASA.21J.052. The technical content of this document has been approved under the authority of DOA ref. EASA.21J.052.
I.9
Accomplishments / Instructions See WI-OSB 42NG-042, latest effective issue.
Diamond Aircraft Industries GmbH N. A. Otto-Straße 5 2700 Wiener Neustadt Austria
DAI OSB 42NG-042 Page 2 of 3 26-Sep-2014
I.10 Mass (Weight) and CG None.
II
PLANNING INFORMATION
II.1
Material and Availability See WI-OSB 42NG-042, latest effective issue.
II.2
Special Tools None.
II.3
Labour Effort Approx. 1 hour.
II.4
Credit None.
II.5
Reference Documents DA 42 NG Airplane Maintenance Manual, Doc. No. 7.02.15, latest effective issue.
III REMARKS 1.
All work must be done by a certified aircraft service station or a certified aircraft maintenance mechanic.
2.
All work, particular that, which is not especially described in this Service Bulletin, must be done in accordance with the referenced Maintenance Manual.
3.
Completion of all work must be recorded in the log book.
4.
In case of doubt contact Diamond Aircraft Industries GmbH.
Diamond Aircraft Industries GmbH N. A. Otto-Straße 5 2700 Wiener Neustadt Austria
DAI OSB 42NG-042 Page 3 of 3 26-Sep-2014
EXECUTION REPORT TO SERVICE BULLETIN OSB 42NG-042
AIRPLANE INFORMATION Airplane Serial Number
_________________
Airplane Registration
_________________
Airplane Operator
_________________
Hours of operation of airplane
_________________
No. of landings
_________________
Hours of operation-engine
Typical operation of airplane
LH
_________________
RH
_________________
private, club, training, other ______________
__________________________________ Date, Name, Sign
Please fax the completed form to Fax No. +43-2622-26700-1369 or e-mail to
[email protected]
Diamond Aircraft Industries GmbH N. A. Otto-Straße 5 2700 Wiener Neustadt Austria
WI-OSB 42NG-042 Revision 0 Page 1 of 2 26-Sep-2014
WORK INSTRUCTION WI-OSB 42NG-042 I
GENERAL INFORMATION
I.1
Subject Provisions for Operation with Diesel fuel.
I.2
Reference Documents DA 42 NG Series Airplane Maintenance Manual, Doc. No. 7.02.15, latest effective issue.
I.3
Remarks a) All work must be done by a certified aircraft service station or a certified aircraft maintenance mechanic. b) All work, in particular if not described in this work instruction, must be done in accordance with the referenced maintenance manual. c) In case of doubt, contact Diamond Aircraft Industries GmbH.
II
DRAWINGS, SPECIAL TOOLS & MATERIALS
II.1
Drawings None.
II.2
Special Tools None.
Diamond Aircraft Industries GmbH N. A. Otto-Straße 5 2700 Wiener Neustadt Austria II.3
WI-OSB 42NG-042 Revision 0 Page 2 of 2 26-Sep-2014
Material
Quantity
Part Number
Description
1
D44-1131-20-08
Limitation Placard - Fuel Temperature
1*)
010-12074-03
G1000 Secondary Configuration Card – Diesel Fuel Operation
*) For Garmin G1000 System Software Versions P/N 010-00670-10 and P/N 010-00670-11. Refer to MSB 42NG-003, latest effective issue. Material is available from Diamond Aircraft Industries.
III INSTRUCTIONS 1
If MÄM 42-480 is not installed, install check valves i.a.w. OSB 42NG-041.
2
Install an E4 Software Version approved for Operation with Diesel fuel i.a.w. MSB 42NG002, latest issue.
3
Make sure the G1000 secondary configuration card P/N 010-12074-03 is installed i.a.w. MSB 42NG-003, latest issue.
4
Install Placard D44-1131-20-08 on the LH canopy frame next to the handle.
5
Make sure TR-OÄM 42-251 is incorporated into the AFM or an AFM revision with this TR incorporated is used.
6
Insert Supplement O05 into the AFM.
7
Clean working areas, check for foreign objects.
8
Check all altered, replaced, repaired parts for proper function.
9
Test all systems in working area for function.
10
Make all necessary entries in the airplane logs.
