Preview only show first 10 pages with watermark. For full document please download

Scion Tc 2011– Tvip V4

   EMBED


Share

Transcript

SCION tC 2011– PREPARATION Part #: PT398-21111 TVIP V4 REMOTE ENGINE STARTER (RES) NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles without RKE systems. Kit Contents RES ECU Bracket RES ECU x1 x1 Hood Switch Sub- Harness V4 Harness x1 x1 Bolt x1 Foam Tape x25 Protective Sheet x3 Remote Label x1 Key Tag x2 08192-07820 x2 91651-60618 90167-20001 Window Label Engine Room Label x2 PT398-2109E Hood Switch Screw x1 PT398-00070-HS PT398-21111-NS Wire Tie Hood Switch x2 PT398-00071-EL x1 PT398-00070-EL Owner’s Guide x1 Service Part #’s Recommended Tools Personal & Vehicle Protection Description Safety Glasses Additional Items (may be required) Item# Description Safety Gloves (Optional) Vehicle Protection Blankets, Parts Boxes Special Tools Techstream Version 4.1 or later Installation Tools Screwdriver #2 Phillips, Flat Blade Jeweler’s, Phillips Jeweler’s Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01 Side Cutters Recommended Sequence of Application Item# 1 Description TVIP V4 Remote Engine Starter 2 TVIP V5 RS3200 PLUS 3 Hands Free BLU Logic 4 Audio / Navigation Unit Issue: B 09/29/10 Torque Wrench Battery: 36 in•lbf (4.07 N•m) Hood Latch: 70.8 in•lbf (8.0 N•m) Driver’s Knee Airbag: 88.5 in•lbf (10 N•m) Tape Clear, Electrical Socket 10mm, extension Pliers Needle Nose Utility Knife or Scissors Ruler Special Chemicals Cleaner VDC Approved Cleaner Glass Cleaner Household Glass Cleaner Page 1 of 40 SCION tC 2011– PREPARATION TVIP V4 REMOTE ENGINE STARTER (RES) Table of Contents I. Preparation............................................................................................................................. 1 – 4 1. Table of Contents.................................................................................................................................................2 2. Wire Routing Overview.................................................................................................................................... 3-4 II. Procedure............................................................................................................................. 5 – 41 1. Preparation..........................................................................................................................................................5 2. V4 Harness Preparation. (Vehicles Without Immobilizer)....................................................................................6 3. Hood Switch Installation.. ....................................................................................................................................7 4. Disassembly....................................................................................................................................................... 11 5. V4 Harness Installation. (Steering Area and Driver’s Side)...............................................................................14 6. RES ECU Preparation and Installation..............................................................................................................23 7. V4 Harness Installation. (Driver’s Side).............................................................................................................25 8. V4 Harness Installation. (Driver’s Side ~ Center Area)......................................................................................27 9. Reassembly.......................................................................................................................................................30 10. Registration Preparation....................................................................................................................................31 11. Registration. (Vehicles Without Immobilizer).....................................................................................................32 12. Registration. (Vehicles With Immobilizer)..........................................................................................................34 13. Tags and Labels.. ..............................................................................................................................................40 14. Complete the Installation...................................................................................................................................41 III. Checklist............................................................................................................................. 42 – 44 1. Accessory Function Checks...............................................................................................................................42 2. Vehicle Function Checks....................................................................................................................................43 Legend Do not proceed until process has been completed. Follow steps carefully to avoid damaging the Vehicle or Accessory Use caution to avoid injury. Used in Figures to call attention to specific tools recommended for the process. Highlights a change in installation with respect to previous issue. Indicates that torque is related to safety. Accessory Installation Practice (read before installation) Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.) • Safety (eye protection, checking torque procedure, etc.) • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.) Please see your SCION dealer for a copy of this document. Video available; click to play. xx Wire Tie location and number. Issue: B 09/29/10 Page 2 of 40 A C5 8P White B C5 8P White C - 2P White D - 2P White E - 24P White (for RES ECU) e - 8P White (for RES ECU) F A F L B U P R K S E Q e D T H G M N - 1P White H - 1P White K C1 Ground Terminal L 2C Wire Terminal (RED Wire) M - 1P White (for Registration) N - 1P White (for Registration) P - Fuse Q - Fuse R - Relay S - Fuse T - Diode U - Sky Blue Tape Marker W - White Tape Marker Z - RES ECU TVIP V4 *Color of Harness on Overview corresponds with Colored Tape near Connectors on Harness. G REMOTE ENGINE STARTER (RES) C C54 5P White 2011– Page 3 of 40 W Z Description tC Vehicle SCION Wire Harness Outline* TVIP PREPARATION Issue: B 09/29/10 Scion tC RES Vehicle A - B A13 2P Black X - 2P Black Y - Hood Switch A TVIP V4 *Color of Harness on Overview corresponds with Colored Tape near Connectors on Harness. REMOTE ENGINE STARTER (RES) B 2011– Page 4 of 40 X 2P Black tC Y Description SCION Wire Harness Outline* (Engine Compartment) TVIP PREPARATION Issue: B 09/29/10 Scion tC RES SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Disassembly Overview 1 9 1 Engine Cover 2 DS Step Cover 3 DS Cowl Cover 4 DS Lower Dash Side Panel 5 DS Knee Airbag * Do not disconnect Airbag Connectors 6 or 6 Lower Steering Column Cover 7 Center Cluster Panel 8 Audio Bracket 9 Audio Unit (if equipped) 8 4 7 5 * 3 2 Disconnect all Corresponding Connectors. Fig. 1-1 1. Preparation. a. Verify that the Short Pin is installed. • If not install now. Issue: B 09/29/10 Page 5 of 40 SCION tC 2011– PROCEDURE Fig. 2-1 10mm Socket TVIP V4 REMOTE ENGINE STARTER (RES) 2. Hood Switch Installation. a. Place the Vehicle in Park with the Parking Brake set. b. Disconnect the Negative Battery Terminal. • Note the Battery Cable Position as it will be re-installed in the same position. CAUTION: Do not touch the Positive Terminal. Fig. 2-2 Nylon Panel Removal Tool c. Remove the Vehicle’s Engine Cover. • Remove 6 Clips. Fig. 2-3 10mm Socket d. Dislodge the Hood Latch Assembly. • Remove 3 Bolts. Issue: B 09/29/10 Page 6 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 2-4 Fig. 2-5 e. Remove the Hood Latch Cable from the Hood Latch. Make sure to hold the Hood Switch by its sides. Make sure the Hood Switch Lever is positioned properly. If the Hood Switch is Broken RES will not function. Fig. 2-6 Needle Nose Pliers, Phillips Jeweler’s Screwdriver f. Release the Spring from the Hood Latch. g. Install the Hood Switch with the Switch Lever underneath the Hood Latch Trigger Lever. h. Reinstall the Spring to the Hood Latch. Issue: B 09/29/10 Page 7 of 40 SCION tC 2011– PROCEDURE Fig. 2-7 Fig. 2-8 Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) i. Route the Hood Switch Sub-Harness as shown. j. Connect the Hood Switch Sub-Harness Connector to the Vehicle’s Pre-Connector. k. Secure the 2P Connectors to the Vehicle Harness with 1 Wire Tie. l. Secure the Hood Switch Sub-Harness to the Bottom Hole of the Vehicle’s Brace using 1 Wire Tie. 2 1 Fig. 2-9 m. Connect the Hood Switch 2P Connector to the Hood Switch Sub-Harness 2P Connector. n. Wrap the 2P Connectors with 1 Foam Tape. Issue: B 09/29/10 Page 8 of 40 SCION tC 2011– PROCEDURE Torque Wrench TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 2-10 o. Reinstall the Hood Latch Cable to the Hood Latch Assembly. Fig. 2-11 p. Reinstall the Hood Latch Assembly. • Position the Bottom Hood Lock mount behind the Vehicle Brace. NOTE: Make sure to Torque the Bolts to 70.8 in•lbf (8.0 N•m) in the specified order. 3 2 1 Fig. 2-12 Side Cutters q. Route the Hood Switch Harness underneath the Hood Latch Assembly. r. Secure the Hood Switch Harness to the Hood Latch Assembly with 1 Wire Tie. CAUTION: Make sure not to secure Hood Latch Cable with Hood Switch Harness. 3 Issue: B 09/29/10 Page 9 of 40 SCION tC 2011– PROCEDURE Fig. 3-1 Nylon Panel Removal Tool TVIP V4 REMOTE ENGINE STARTER (RES) 3. Disassembly. a. Remove the Driver’s Side Step Cover. • Disengage front inner sill clip and front clip. • Disengage rear inner sill clip and rear clip. • Hold ends up keeping guide pins up and slide sill forward to disengage remaining clips. NOTE: Make sure to carefully follow steps above to avoid breaking sill plate clips. Nylon Panel Removal Tool Fig. 3-2 b. Remove Driver’s Side Cowl Cover. Nylon Panel Removal Tool Fig. 3-3 c. Remove the Driver’s Lower Dash Side Panel. • Open the DTC Connector Cover. Issue: B 09/29/10 Page 10 of 40 SCION tC 2011– PROCEDURE Nylon Panel Removal Tool, Flat Blade Jeweler’s Screwdriver, Electrical Tape TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 3-4 d. Remove the Lower Steering Column Cover. • Use a Flat Blade Jeweler’s Screwdriver wrapped with Electrical Tape to release the clips. • Insert the Key into the Ignition and turn it to on. • Turn the Steering Wheel from Right to Left to access the Holes. • Dislodge the back Clips on both sides. • Release the Front Clips on both sides. Fig. 3-5 10mm Socket, Extension e. Dislodge the Driver’s Knee Airbag carefully. • Remove 4 Bolts CAUTION: Do not disconnect the Airbag Connectors. Fig. 3-6 f. Wrap the Airbag in a Blanket or the like and place it on top of the TVIP box. CAUTION: Position the Airbag as to Prevent stress on the Airbag Harness. Issue: B 09/29/10 Page 11 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Nylon Panel Removal Tool Fig. 3-7 g. Remove the Center Cluster Panel. 10mm Socket, Extension Fig. 3-8 h. Remove the Driver’s Side Audio Bracket. • Remove 2 Bolts. IF EQUIPPED w/AUDIO UNIT i. Remove the Audio Unit. • Remove 4 Bolts. Fig. 4-1 Side Cutters 4. V4 Harness Installation. (Steering Area and Driver’s Side) V4 ONLY a. Secure the V4 Harness’s White Tape Marker to the Vehicle Harness right next to the Harness Clamp with 1 Wire Tie. 4 Issue: B 09/29/10 Page 12 of 40 SCION tC 2011– PROCEDURE Fig. 4-2 Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) b. Secure the 2P Connectors to the Vehicle Harness with 1 Wire Tie. Go to step n. 5 Fig. 4-3 Side Cutters V5/V4 ADD-ON ONLY c. Cut the Wire Tie securing the V5 8P Connectors. d. Cut 4 Wire Ties securing the V5 Harness. Fig. 4-4 e. Disconnect the V5 8P Connector from the Vehicle’s 8P IG Connector. f. Disconnect the Vehicle’s 8P Connector from the V5 Harness’s 8P Connector. Issue: B 09/29/10 Page 13 of 40 SCION tC 2011– PROCEDURE Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 4-5 g. Cut 2 Wire Ties securing the V5 Harness. Fig. 4-6 h. Disconnect the V5 2P Connectors. • Discard the V5 Male 2P Connector’s Harness. Fig. 4-7 i. Remove the Tape securing the V4 2P Connector. j. Disconnect the 2P Connector from the V4 Harness. • Discard the 2P Jumper Connector. Issue: B 09/29/10 Page 14 of 40 SCION tC 2011– PROCEDURE Fig. 4-8 Fig. 4-9 Side Cutters 4 Fig. 4-10 Side Cutters 5 Issue: B 09/29/10 Page 15 of 40 TVIP V4 REMOTE ENGINE STARTER (RES) k. Connect the V4 Male 2P Connector to the V5 Female 2P Connector. l. Secure both the V4 and V5 Harness’s White Tape Markers to the Vehicle Harness right next to the Harness Clamp using 1 Wire Tie. m. Secure the 2P Connectors to the Vehicle Harness with 1 Wire Tie. SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 4-11 n. Fully extend the Steering Wheel Column. • Release the Tilt and Telescopic Lever. Fig. 4-12 Side Cutters o. Route the V4 Harness’s 8P Connectors towards the Steering Column Area. p. Secure the V4 Harness to the Vehicle Harness with 1 Wire Tie. 6 Fig. 4-13 Issue: B 09/29/10 Page 16 of 40 CAUTION: Make sure the V4 Harness is not placed between the Vehicle Harness and the Steering Motor. SCION tC 2011– PROCEDURE Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 4-14 q. Disconnect the Vehicle’s 8P IG Connector. Fig. 4-15 r. Plug the V4 8P Connectors in between the Vehicle’s 8P Connectors. Fig. 4-16 s. Secure the 8P Connectors to the Vehicle Harness with 1 Wire Tie. • Bundle up the 8P Connector and Harness as shown. CAUTION: Make sure not to include the Yellow Airbag Wires when securing the 8P Connectors. 7 Issue: B 09/29/10 Page 17 of 40 SCION tC 2011– PROCEDURE Fig. 4-17 Side Cutters Point of View Good Vehicle Harness Point of View 8 TVIP V4 REMOTE ENGINE STARTER (RES) t. Secure the V4 Harness to the Vehicle Harness with 3 Wire Ties. NOTE: Place the V4 Harness parallel to the Vehicle Harness. V5 No Good Vehicle Harness V5 9 V5 or 10 Issue: B 09/29/10 Page 18 of 40 Fig. 4-18 u. Disconnect the Vehicle’s 1P Pre-Connector located on the right side of the Junction Box. Fig. 4-19 v. Connect the V4 Harness’s 1P Connectors in between the Vehicle’s 1P Connectors. SCION tC 2011– TVIP V4 PROCEDURE REMOTE ENGINE STARTER (RES) Fig. 4-20 Side Cutters Point of View Point of View • V4 Relay should be secured to the Vehicle Harness as shown. Good Vehicle Harness Junction Box No Good 12 Junction Box x. Route the V4 Harness’s RED wire toward the front of the Junction Box. V4 Relay 11 w. Secure the 1P Connectors and Relay to the Vehicle Harness with 2 Wire Ties. V4 Relay Vehicle Harness or V4 Relay Fig. 4-21 Example y. Locate and Disconnect the Vehicle’s 48P Connector from the Junction Box. • Release the Black Connector Lever. Fig. 4-22 z. Remove the Black Connector Lever. • Release the lock on both sides of 48P Connector. CAUTION: Do not force the lever. Issue: B 09/29/10 Page 19 of 40 SCION tC 2011– PROCEDURE Fig. 4-23 Flat Blade Jeweler’s Screwdriver TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 4-24 aa. Lift the Terminal retainer Clip. CAUTION: Do not pull out the Retainer Clip. ab. Insert the V4 Red Wire Terminal into the indicated location on the 48P Vehicle Connector. VERIFY: Terminal Pins are properly inserted and do not come out. Terminal Retainer 1 2 3 4 5 6 Wire Side View Fig. 4-25 ac. Close the Terminal Retainer Clip. ad. Re-attach the Black Connector Lever. Issue: B 09/29/10 Page 20 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 4-26 ae. Reconnect the Vehicle’s 48P Connector. Fig. 4-27 af. Secure the V4 RED Wire to the Vehicle Harness with 1 Wire Tie. Fig. 4-28 ag. Secure the V4 RED Wire to the Vehicle Harness with 1 Wire Tie. Example Side Cutters 13 Side Cutters 14 Issue: B 09/29/10 Page 21 of 40 SCION tC 2011– PROCEDURE Fig. 5-1 Ruler, Scissors or Utility Knife TVIP V4 REMOTE ENGINE STARTER (RES) 2.75 in. (70 mm) 5. RES ECU Preparation and Installation. a. Cut the Protective Sheet as shown. • Discard the Protective Sheet C . 1.0 in. (25 mm) Discard C B A Fig. 5-2 Fig. 5-3 b. Attach RES ECU Bracket to the RES ECU. c. Using VDC approved Cleaner and cleaning method, clean the area indicated on the ECU Bracket. • Do not clean the RES ECU. Issue: B 09/29/10 Page 22 of 40 SCION tC 2011– TVIP V4 PROCEDURE REMOTE ENGINE STARTER (RES) Fig. 5-4 d. Attach the Protective Sheet A on the edge of the ECU Bracket as shown. • Do not place sheet beyond the Red Line. • Make sure the Protective Sheet adhere tenaciously to the surface of the Bracket. A Fig. 5-5 • Do not place sheet beyond the Red Line. 2 • Make sure the Protective Sheet adhere tenaciously to the surface of the Bracket. B 3 1 e. Attach the Protective Sheet B on the edge of the ECU Bracket as shown. 2 3 1 Fig. 5-6 10mm Socket f. Position the RES ECU behind the Driver’s side Junction Box as shown. g. Install the RES ECU to the Vehicle’s Brace using the supplied Bolt. NOTE: Make sure the Guide Pin is seated correctly. Issue: B 09/29/10 Page 23 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 6-1 6. V4 Harness Installation. (Driver’s Side) a. Plug in the V4 Harness’s 24P and 8P Connectors to the RES ECU. Side Cutters Fig. 6-2 b. Secure the V4 Fuses to the Vehicle Harness using 2 Wire Ties. Fig. 6-3 c. Secure the V4 Harness to the Vehicle Harness using 2 Wire Ties. 16 15 Side Cutters • Route the V4 Harness above the Hood Release Cable. 17 18 Issue: B 09/29/10 Page 24 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) 10mm Socket Fig. 6-4 10mm Socket, Side Cutters Fig. 6-5 d. Remove the Vehicle’s Ground Terminal Bolt from the Driver’s side Cowl Area. e. Secure the V4 Ground Terminal to the Vehicle’s Ground Terminal using the same the Bolt. f. Secure the V4 Harness to the Vehicle Harness with 1 Wire Tie. 19 Fig. 7-1 7. V4 Harness Installation. (Driver’s Side ~ Center Area) a. Route the V4 Harness behind the Vehicle Brace toward the Center Cluster Area. Issue: B 09/29/10 Page 25 of 40 SCION tC 2011– PROCEDURE Fig. 7-2 Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) b. Secure the V4 Harness’s Sky Blue Tape Marker to the Vehicle’s Brace with 1 Wire Tie. 20 Fig. 7-3 Fig. 7-4 Side Cutters V4 ONLY c. Connect the V4 5P Connector to Vehicle’s 5P Pre-Connector located in the Center Cluster Area. d. Secure the 5P Connectors to the Vehicle Harness with 1 Wire Tie. e. Secure the V4 Harness to the Vehicle Harness with 1 Wire Tie. NOTE: Make sure that the Audio USB Cable is not secured with the V4 Connectors. 22 21 Issue: B 09/29/10 Go to section 8. Page 26 of 40 SCION tC 2011– PROCEDURE Fig. 7-5 10mm Socket TVIP V4 REMOTE ENGINE STARTER (RES) V5/V4 ADD-ON ONLY f. Remove the Screw securing the V5 ECU. • Do not discard the Screw. Side Cutters Issue: B 09/29/10 Page 27 of 40 Fig. 7-6 g. Cut the Wire Tie securing the V5 Harness. Fig. 7-7 h. Remove the Tape securing the V5 Harness’s Female 5P Connector. SCION tC 2011– PROCEDURE Fig. 7-8 Fig. 7-9 Side Cutters TVIP V4 REMOTE ENGINE STARTER (RES) i. Connect the V5 Harness’s Female 5P Connector to the V4 5P Connector. j. Secure the 5P Connectors to the Vehicle Harness with 1 Wire Tie. NOTE: Make sure that the Audio USB Cable is not secured with V4/V5 Connectors. 14 Fig. 7-10 10mm Socket Issue: B 09/29/10 Page 28 of 40 k. Reinstall the V5 ECU using the same Screw. SCION tC 2011– PROCEDURE Fig. 8-1 10mm Socket, Torque Wrench TVIP V4 REMOTE ENGINE STARTER (RES) 8. Reassembly. a. Reinstall the Driver’s side Knee Airbag. • Install 4 Bolts. NOTE: Make sure to tighten the Bolts to 88.5 in•lbf (10 N•m). Fig. 8-2 b. Using VDC approved cleaner and cleaning method, clean the area indicated on the Lower Steering Column Cover. c. Apply 2 Foam tapes as shown. NOTE: Do not perform above steps if Foam Tapes are already present. Fig. 8-3 Issue: B 09/29/10 Page 29 of 40 d. Reinstall the Lower Steering Column Cover. SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 9-1 10mm Socket, Phillips Screwdriver 9. Registration Preparation. a. Reassemble the Vehicle except for the Driver’s Cowl cover and Step cover. Note: Make sure that all Connectors are reconnected. or Note: Verify that panels fit together properly, with no uneven gaps. ALREADY INSTALLED DO NOT INSTALL Fig. 10-1 10mm Socket 10. Registration. a. Open the Hood. b. Temporarily reconnect the Negative Battery Cable. CAUTION: Do not touch the Positive Terminal. Fig. 10-2 c. Locate the 1P RES Diagnostic Connectors in the Driver’s Side Cowl Area and connect them. NOTE: Once connected you will have 10 minutes to complete this section, steps c-ad. d. Close all doors. Issue: B 09/29/10 Page 30 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 10-3 e. Insert the Key into the Ignition. f. Turn it from “OFF” to “ON” 5 times. LOOK: For the Hazard Lights to flash Once. g. Turn the Key to the “OFF” position. Fig. 10-4 h. Start the Engine. i. After 10 seconds stop the Engine. LOOK: For the Hazard Lights to flash Once. 10 Seconds Fig. 10-5 IF THIS PROCEDURE FAILED The Hazard Lights won’t flash or flashes Twice. • Disconnect the V4 Harness’s 1P RES Diagnostic Connectors. • Start again from step c. Issue: B 09/29/10 Page 31 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) j. Fig. 10-6 Techstream Connect the Techstream Notebook to the Vehicle’s Diagnostic Port. k. Turn the Key in the Ignition to the “ON” position. Fig. 10-7 TIS techstream File Function Setup TIS User Help Connect to Vehicle Open Scan Data File Launch TIS TIS techstream l. Start the TIS Techstream Application by clicking on the shortcut located on the Desktop. m. Click “Connect to Vehicle.“ New Users Demo Check for Scantool Updates Generic OBD II Software Registration User/Language Selection Log Out ABS Ver x.xx.xxx Fig. 10-8 n. Confirm that the information displayed on the Vehicle Connection Wizard is correct for the vehicle. If not verify that the Techstream is properly connected. o. Select w/o Smart Key. p. Click “Next>.” wo/Smart Key Issue: B 09/29/10 Page 32 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) q. Select “Body Electrical” tab. Fig. 10-9 r. Select “Remote Engine Starter“. s. Click . t. Select “Utility.“ Fig. 10-10 TIS techstream - 10645 File Function Setup TIS System Select User Help Stored Data Customize v. Click Utility Selection Menue Select desired Utility and then press Next button. Trouble Codes u. Select “ECU Communication ID Registration.” Custimize ECU Communication ID Registration Smart Code Registration . Communication Check(Key Diag Mode) Smart Code Erasure Smart Code Reset Data List Active Test Monitor Utility Print Close S601-03 Generic English DLC3 Fig. 10-11 w. Confirm the Conditions on the screen. x. Click “Next>.” Issue: B 09/29/10 Page 33 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Fig. 10-12 y. Follow the steps on the Techstream. z. Click “Next>.” Fig. 10-13 CONFIRM: That the ECU Communication ID was completed successfully. aa. Click “Exit.” Fig. 10-14 System Select User Help Stored Data XXXX XXXXXXXX xxx-xx Communication System Selection ECU Menu ID Registration (SMRT-13-001) (SMRT-13-001) Sel e c t d e si r e d sy s t e m aECU n d t hCommunication e n p r e s s L iv e D a ID t a tRegistration o access the E C U. xxxxxxxxxxxxxxxxx Health Check Customize Setting ECU Reprogramming CAN Bus. Check System Yellow = ECU status unknown. System White = ECU communication OK. *System White w/Asterisk = ECU not supported or not responding. All ECUs Step 1 of 1(SMRT-13-001) ECU Communication ID Registration Powertrain Chassis Body Electrical Air Conditioner Remote Engine Starter Welcome to the Communication ID 1. Remove theECU master key from the key SRS Airbag Main Body Back Door Registration utility. cylinder. ECU ID Registration has Smart Communication Key Occupant This function used to perform the 2. Insert key intoDetection the key failed.theismaster “handshake” between theconditions Immobilizer cylinder. Verify the following are met. and Remote Starter. 3. Turn the Engine IG switch ON. key is in the key 1. A registered master cylinder. Confirm the IG following 2. The switch conditions: is ON. Do you want to trykey again? 1. A registered master is in the key cylinder. 2. The IG switch is ON. ! Try TimeAgain Remaining: D Door Motor Sliding Roof Exit XXX sec. This ECU controls keyless entry and starting engine with the detection SmartKey. Press Next to proceed. TIS Search Cancel Next> Cancel Next> Print Main Menu S601-03 Issue: B 09/29/10 • Click “Try Again”. • Start again from step u. TIS techstream - 10645 File Function Setup TIS IF THIS PROCEDURE FAILED Generic English DLC3 Page 34 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) ab. Exit the vehicle. Fig. 10-15 ac. Close the Hood. ad. Look for the Hazard to flash Twice. IF THIS PROCEDURE FAILED The Hazard Lights flash Three Times. • Disconnect the V4 Harness’s 1P RES Diagnostic Connectors. • Start again from step c. Fig. 10-16 Electrical Tape ae. After a successful Registration, disconnect the 1P RES Diagnostic Connectors. af. Using Electrical Tape secure the 1P RES Diagnostic Connectors and Harness to the Vehicle Harness. Issue: B 09/29/10 Page 35 of 40 SCION tC 2011– PROCEDURE Fig. 11-1 Clear Tape TVIP V4 REMOTE ENGINE STARTER (RES) 11. Tags and Labels. a. Using VDC approved cleaner and cleaning method, clean the area indicated in the Engine Compartment Cover. b. Attach the Engine Room Warning Label as shown. 10mm CAUTION: Do not touch the adhesive surface. Fig. 11-2 Clear Tape c. Using VDC approved cleaner and cleaning method, clean the indicated area on the key. d. Use a piece of Clear Tape to lift the label off its protective backing. CAUTION: Do not touch the adhesive surface. e. Attach the Key Label as shown. f. Attach the Key Tag to the Key ring. REPEAT: steps c–f with the other Key. Fig. 11-3 Clear Tape 10 mm g. Use Household Glass Cleaner to clean the inside of the Front Door Windows. h. Use a piece of Clear Tape to lift the Label from the protective backing. CAUTION: Do not touch the adhesive surface. i. NG HI S C T EL E E LAB H T R TO THE N O IG AL N TO O G I T W AL HO TO W HO Issue: B 09/29/10 1– 5 mm Attach the Label as shown. NOTE: Make sure to Align according to Etching or Other Label. REPEAT: steps g–i with the other Window. Page 36 of 40 SCION tC 2011– PROCEDURE Fig. 12-1 10mm Socket, Phillips Screwdriver TVIP V4 REMOTE ENGINE STARTER (RES) 12. Complete the Installation. a. Finish reassembling the Vehicle. VERIFY: That panels fit together properly, with no uneven gaps. or VERIFY: That all Connectors are plugged in. ALREADY INSTALLED Fig. 12-2 10mm Socket, Torque Wrench b. Position the Negative Battery Cable at the original factory position. • Tighten the Nut to 36 in•lbf (4.07 N•m) CAUTION: Do not touch the positive terminal. c. Clean up and Remove trash. d. Sealed in its protective bag, place the Owner’s Manual in the Glovebox. e. Reset the power windows. • Turn the ignition “ON.” • Lower the Windows halfway. • Pull up on the Power Window Switches until the windows close. • Continue to hold up on the switches for a minimum of 1 Second. f. Reset the Moon Roof. (If equipped) • Turn the ignition “ON.” • Open the Moon Roof halfway. • Push and hold the Moon Roof Switch to close until the Moon Roof closes. • Continue to hold the switch for a minimum of 1 Second. Issue: B 09/29/10 Page 37 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Accessory Function Checks Close the hood, enter the vehicle and close all doors. Place the shift lever in the “P” (Park) position, set the parking brake and make sure the Vehicle is off. Perform Look For 1 Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. The hazard lights flash after 3 seconds. The engine starts. The hazard lights flash repeatedly for 10 seconds. 2 With the engine running, pull the hood release handle. The engine stops. The hazard lights flash once. The security alarm triggers. (only if equipped with OE Factory Alarm, not Genuine Accessory alarm, and only if armed) NOTE: Some Vehicles may require you to exit the Vehicle and pull up on the Hood. 3 Move the shift lever out of “P” (Park). Attempt to start the Vehicle using the remote. Issue: B 09/29/10 The engine does not start. Page 38 of 40 SCION tC 2011– PROCEDURE TVIP V4 REMOTE ENGINE STARTER (RES) Vehicle Function Checks Function Function Enter the Vehicle □ □ Dome/Courtesy Lights Starter □ Panel/Switch Illumination □ Lamp Failure Sensor □ Seat Belt Warning Light □ □ If the warning light remains on, it may indicate a system malfunction. If the warning light remains on, it may indicate a system malfunction. □ □ □ Track/Skid Control Light (if equipped) □ Tire Pressure Monitoring System (TPMS). (if equipped) Backup Lights If the warning light remains on, it may indicate a system malfunction. After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on. Cruise Control Light (if equipped) Brake Lights If the warning light remains on, it may indicate a system malfunction. Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on. If the warning light remains on, it may indicate a system malfunction. Trunk/Tailgate/Bed Lights (if equipped) Gauges ABS Light (if equipped) Air Bag Warning Light Using a Mirror or Assistant check the following. □ □ □ □ Steering Wheel Column Adjusts Without Interference Horn Start the Vehicle □ □ □ □ □ Tail Lights Daytime Running Lights (if equipped) Marker Lights Clearance Sonar (if equipped) Stop the Engine, Place the Vehicle’s IG in the ON position. □ □ □ □ □ Hazard Lights Head Light High Beams Power Side Mirrors (if equipped) Power Sliding Door (if equipped) Issue: B 09/29/10 □ □ □ □ □ Page 39 of 40 Turn Signal Lights Fog Lights (if equipped) Accessory Controls/Illumination (if equipped) Convenience Memory Settings (if equipped) Rear Sunshade (if equipped) SCION tC 2011– PROCEDURE □ □ □ □ □ □ □ □ □ □ □ Function Front Wiper/Washer Power Sun/Moon Roof (if equipped) Clock (if equipped) Audio/Video (if equipped) Steering Wheel Audio Control (if equipped) Front Windshield Defogger (if equipped) Side Mirror Defogger (if equipped) □ □ □ □ □ □ □ TVIP V4 REMOTE ENGINE STARTER (RES) Function Rear Wiper/Washer (if equipped) Rollover Side Curtain Air Bag Switch (RSCA) (if equipped) Navigation System (if equipped) HVAC Rear Window Defogger (if equipped) Accessory Power Socket (if equipped) Heated/Vented Seats (if equipped) Massage Seats (if equipped) Glovebox Light (if equipped) Power Locks (if equipped) Power Seats (if equipped) □ □ □ Remove the short pin after Function check. Check with your Port/Dealer to see if this step is necessary. Issue: B 09/29/10 Page 40 of 40 Passenger Air Bag Switch (if equipped) Power Windows (if equipped) Key Sensor Buzzer