Transcript
SEAWING
SC-1000 WebStar General Outlines
General SC-1000 WebStar is the entry level system of SEAWING, designed to meet the demands on access control systems to be installed and managed easily, with the maximum possible flexibility on tags (cards) and readers to use, also to be capable of controlling a wide variety of electronically controllable access blocking devices. To make it really simple to manage, there is no need to install software on PCs as it has a built-in WEB server manageable via WEB.
Capabilities SC-1000 Webstar is capable of controlling up to 16 access points with 2 readers of each, 32 access points equipped with one reader of each, and a combination in between. To build-up larger access control systems, SEAWING offers its SIS systems, where there is no limit for the size of the systems. All hardware components of SC-1000 WebStar can be used when upgrading the system for SiS. This concept opens the possibility for a low cost upgrading.
Applicable ID tag types – compatible readers Practically, all commonly available ID tag readers can be managed by the system. e.g.: MIFARE, HID, Indala, EM, UHF, Hyper-X, etc.
Applicable electronically controllable access blocking devices e.g.: magnetic strikes, turnstiles, speed gates, barriers, etc.
Operation The access control modules communicate the events immediately to the controller on the CAN bus. Events are processed by the controller and it responds on them according to the rules stored in it. After processing the event, the controller sends commands to the modules via the CAN bus requesting them for the adequate reaction. Continuous connections between the controller and the modules are required for the correct operation. Time-stamps, provided by the controller, are added to the events and they also stored in its memory for further processing, creating reports. Setup is done via the WEB server utilizing a standard internet browser.
2
SEAWING
SC-1000 WebStar General Outlines
SC-1000 WebStar -the ideal solution to create an entry-level access control system Advantages when installing: • Quick and simple installation • Just follow the wiring instructions when installing the system • No IT knowledge required • No software installation required as the system is WEB-server based with high level services • Simple configuring, automatic module recognition • Following the hardware installation, it provides the possibility of full operation • Loading or saving master data can also be made in an Excel file format
Advantages in everyday use: • WEB-browser only required for the system management and supervision (Explorer, Firefox, Opera, etc) • Bilingual operator platform (English – Hungarian as default) • Built-in translator for to make the operator platform speak in different languages • Language setting options for the operator platform by operators -2 languages simultaneously • 4 levels of system management can be set with password protection • Capable of managing 5 different FCs (facility code) to manage common access points of office buildings with different tenants • Optional access right distribution by access points with different time-zones • 16 different time-zones with 90 time slots • Setting possibilities for to manages special calendar days with altering rules for access • 3 different ways for to enter ID cards into the system: by reading them, defining an interval or importing them from an Excel file • Granting and deleting access rights can be made individually, by user groups or entirely • Copy-paste for to create simple access profiles • Built-in Quick Guide and User Manuel with instant access • Effective service support with built-in self-checking diagnostics modules
Additional high level services: • The system manages 500 cards (tags) as a default • In full configurations, it can take 16 access points with bidirectional identification or 32 access points with single directional identification or any combination in between. • It has an events memory capable of storing 100 000 events at a time • Remote management according to entitlement levels • Various event tracking functions (by time-intervals, users, access-points, event types, etc) • On-line event monitoring • Report generation, exporting reports • Map management with icons representing the type and status of the access points.
3
SEAWING
SC-1000 WebStar General Outlines
System charts
Adding access control modules The limits of the SC-1000 WebStar is: • 1x SC-1000-01 group controller • 16x active SC-1000-02 access control ,module
4
SEAWING
SC-1000 WebStar General Outlines
Packages of components SC-1000 Basic Kit + 7Ah battery • • • • •
SC-1000-D large metal box SC-1000-01 group controller SC-1000-02 x2 access control module PWS-12-20 12V/2A linear power supply Akku-7 12V 7Ah battery
SC-1000-02-D middle-size sheet metal box SC-1000-D middle-size metal box SC-1000-01 group controller SC-1000-02 x1 access control module PWS-12-20 12V/2A linear power supply Akku-7 12V 7Ah battery
• • • • •
SC-1000-02 access control module in a sheet metal box SC-1000-D SC-1000-02
• •
small-size metal box x1 access control module
PWS-12 Power supplies in a sheet metal box • • •
PWS-12-10 12V 1A PWS-12-20 12V 2 A Akku-7 7Ah battery
5
SEAWING
SC-1000 WebStar General Outlines
WEB Management SC-1000 WebStart is designed to have an on Operator platform (samples) board WEB server to run the application software. It provides the required software tools and services Assigning access authorisations to set up and operate the system via an internet browser. SC-1000 WebStar application software services have an elegant graphics platform. When in operation, SC-1000 WebStar can practically be accessed from any kind of IT networks. To do so, you need the appropriate network settings and access path. Interconnection between the SC-1000 WebStar and the PC can be made by connecting them to the Setting up time zones same IT network or by using an Ethernet cross cable. SC-1000 WebStar can be started from any Internet browser. (Flash Player is required.) Type in the followings into the search line of your Internet browser: http://IP address For the first occasion: http://10.100.100.1
Communications language of the WEB server
SC-1000 WebStar has memory space for two Events report languages to choose from for its operator platform. One of them is English, as standard, and the other one is optional. A language manager to translate the operator platform to different languages is also available for SC-1000 WebStar (translator software, users guide and the assembly of phrase definitions applied). With the help of these, the operator platform can be prepared for to take a new language beside the Firmware upgrade English. For to help the translation, each window of the operator platform has a unique identifier displayed at the upper left-hand corner.
Additional services of the WEB server Following chart provides a summary of the WEB server services available by user authentications (guard, administrator, supervisor, and installer).
6
SEAWING
SC-1000 WebStar General Outlines
WEB Management - Menu System
User Authorisations Guard
Reports
Supervisor
Installer
x
x
x
x
Event monitor Event report User
x -
x x x
x x x
x x x
x
x
x
x
Terminal status Grid view Map view Change password Logout
x x -
x x x
x x x x x
x x x x x
-
x
x
x
-
x x x x x -
x x x x x x x
x x x x x x x x x x x
-
-
x
x
-
x x x -
x x x x x x x x x -
x x x x x x x x x x x x x x x x x x x x x
Operations
Editor
Administrator
System manager Module Terminal Time zone FC Identifier (ID) Authorisation Map Backup and restore Create backup Restoring
System
Restart Date and time settings IP settings Module status Module connections test Configurations file Preview Restore factory default Restore last correct configurations Terminal configurations ID database IDs in memory Delete Events log status Options Firmware File operations Firmware upgrade Log files Configurations error log Test log
7
SEAWING
SC-1000 WebStar General Outlines
SC-1000-01 Group Controller SC-1000-01 group controller operates the access control modules and logs the events. • CAN bus is used for the communications between the controller and the access control modules. • SC-1000-01 has an Ethernet connecting capability for to make it accessible from LAN. • For SC-1000 WebStar, a built-in WEB server is also added with on boar application software to setup the access control systemand analyse the events.
Main features
T e c h n i c a l s p e c i fi c a t i o n s Type Metal box Installation environment
SC-1000-01 Group Controller Box „A”
Box „B”
Indoor use
Metal box
Sheet metal box, powder coated finish
Outside dimensions
Power
335 x 455 x 95 mm 5,9kg (without battery) 12 V DC
Current requirement
45 mA
Weight
240 x 380 x 95 mm 4,2kg (with battery)
Maximum current requirements
135 mA (without USB device)
Accuracy
1 sec
Maximum number of events stored Maximum number of IDs Maximum number of connecting modules
•
400 MHz processor
•
LINUX operating system
•
Watch dog
•
Built-in WEB server
•
Tamper sensor
•
Ethernet port
•
2x CAN bus
•
RS-485 bus
•
2x serial port
•
6x input
•
2x relay outputs
•
Power supply supervision
•
2x USB port
Indications of the controller, default settings
100000 20000 (100000 with limitations)
TYPE
32
Number of tag readers
Applies for the modules only (2x / module tipycal)
Number of inputs
2 + inputs available on the modules
Number of outputs
2x relay dry contacts + outputs on the modules
Communications lines
• • • •
Tamper protection
Tamper switch + loop
Operating temperature
-5 ÷ +50Cº
Relative humidity
10% ÷ 95% non-condensing
Storage temperature
-20 ÷ +60Cº
LED displays: • LD1 / POWER: • LED1 / Status: •
LR2 / TX
• LG3 / RX Jumpers: • JP1 / Battery:
RJ45 Ethernet 100Mbit CAN 62,5 kbps USB (Full speed) RS-485, RS-232
•
JP3 / CAN1 TERMINATOR:
JP5 / MFG DEFAULT: Push button: RESET: •
8
SC-1000-01 Red – power Green – operating status of the system CAN bus communications
Connecting back-up battery Connecting CAN bus terminating resistor Operating mode
Restarting the controller
SEAWING
SC-1000 WebStar General Outlines
SC-1000-02 Access Control Module SC-1000-02 access control module can manage one two way or two one way access points. Practically all kinds of available tag (card) readers and electronically controllable access blocking devices (magnetic strikes, turnstiles, speed-gats, barriers, e.t.c.) can be connected to it.
Technical specifications Type
Installation / operation Power connections Power Current requirement Tag readers Inputs Outputs Communications Operating temperature Relative humidity Storage temperature
SC-1000-02 Access Control Module It can be installed separately but only operates under the control of SC-1000-01. Independent module and device connections 12V DC 58mA (without tag reader) 2x ABA track2 or Wiegand 4x contacts NC or NO 2x relay dry contact CAN 62,5kbps -5 ÷ +50Cº 10% ÷ 95% non-condensing -20 ÷ +60Cº
Main features • • • • • •
Access control module – indications, default settings Type LED displays: • LD1 / POWER: • LD2 / DIAG: Amber, operating status of the module:
Manageable tag readers • MIFARE • HID • INDALA • EM (ASK) • UHF readers • HYPER-X • etc. ABA track2 or Wiegand interface types. Facility code (FC) or ID only management or the combination of them.
SC-1000-02 Access Control Module
Red - power Continuously on: OK
Turns On & OFF in every second: Connections is OK, not configured Short flash in every 5 seconds: there is no CAN connection with the controller • LD3 / CAN RX: • LD4 / CAN TX: Jumpers: • JP1 / CAN TERMINATOR: Push button: • RES / RESET:
CAN bus 2x tag reader interface 4x dual-state input 2x relay output Tamper sensing RS-232 interface (not used for WebStar version).
Manageable access blocking devices All kinds of • • • • •
CAN bus communications
magnetic strikes turnstiles speed-gates barriers etc.
Note: There is a “Wiring Instruction” guide is available for the system to provide help for connecting the various readers and access blocking devices.
Connecting CAN bus terminating resistor at the end of the CAN bus Module restart (HW reset)
9
SEAWING
SC-1000 WebStar General Outlines
MFN/MFS-300 series of proximity readers MFN-310/311 readers are capable of reading the unique ID (UID) of Mifare Plus tags. These readers can recognise any Mifare Plus 1K, 4K tags. MFS-310/311 readers can also read a sector of Mifare Plus tags. Security level of sector readers is much higher as assess to sector data only available for readers with the matching access key to make illegal copying practically impossible.
Available models: TYPE Readers MFN-310 MFN-311
DESCRIPTION MIFARE Plus UID reader – dark grey MIFARE Plus UID reader – beige
MFS-310 MIFARE Plus UID + sector reader – dark grey MFS-311 MIFARE Plus UID + sector reader – beige R/W devices Call for availability
Technical specifications: TYPE
MFN-310/311 MFS-310/311
Description: Read range: Case: Installation environment: Finish:
RFID reader Maximum 5cm* ABS Indoor (IP 44) / Outdoor (IP 64) MFR, MFS-310 dark grey MFR, MFS-311 beige 80x80x26mm 72g Multicolour LED Single-tone buzzer 7-14VDC 100mA @ 12VDC 13,56Mhz ABA track 2 Wiegand26, 34, 40 Serial MIFARE Classic 1k MIFARE Classik 4k
Dimensions (HxWxD): Weight: Visual indication: Audio indication: Power: Maximum consumption: Transmitting frequency: Data format:
Recognised proximity tag types: Operating temperature: Data read:
Tamper signal:
All devices use cryptographic communications between the reader and the tag/card via ABA/Wiegand or serial interface. Cryptographic communications between the controller and the reader is optional and can only be applied for devices with serial interface. For high security systems, they offer tamper protection and continuous presence monitoring as an option. The readers can be installed on flat wall surface but also prepared to be installed on Ø60 electrical wall boxes too.
Recognised and managed tag (card) types • MIFARE Plus 1K, 4K Note: Various models of these devices can recognise MifarePlus S/X, DESFire EV1 tags and cards, and in addition, some of the models can even write on them.
-25...+65°C • MFN - Serial number UID • MFS- Sector contents with Seawing coding Separate NC contact or transmitted via communications line
*with ISO card in a noise-free environment
10
Main features • • • •
High security Independent applications on a single tag (card) body Wall-mounting & desktop design Tamper protection
SEAWING
SC-1000 WebStar General Outlines
MSW-400 series proximity readers SW-MP-400 is a series of RFID readers and read/write devices providing perfect solution for applications requiring extremely high security RFID technology. All devices comply with the provisions of 13,56 MHz, ISO/IEC 14 443A-4 standard. Protection of data stored on the cards is on the highest technical level currently known. MIFARE Plus and DESFire EV1 readers and cards are protected against illegal access or modification attempts.
Available models: TYPE Readers SW-MP-400 SW-MP-400 DESFire SW-MP-400 Classic SW-MP-400 UID
R/W devices SW-MP-400 RW SW-MP-400 DESFire RW SW-MP-400 Classic RW
DESCRIPTION Mifare Plus X/S reader DESFire reader Mifare Classic sector reader 14443 A unique ID reader (reads unique ID of Mifare Plus, Mifare Classic, DESFire tags) Mifare Plus X/S R/W device with RS-232 interface DESFire R/W device with RS-232 interface Mifare Classic R/W device with RS-232 interface
Recognised and managed tag (card) types
Technical specifications: TYPE Description: Read range: Case: Installation environment: Finish: Dimensions (LxWxD): Weight: Visual indication: Audio indication: Power: Maximum consumption: Transmitting frequency: Data format: Recognised proximity tag type: Operating temperature: Tamper sensor: Tamper signal:
DESCRIPTION RFID reader RFID read/write device Maximum 5cm* ABS Indoor (IP 44) / Outdoor (IP 64) black 120x80x25mm 200g Four-colour visual indication Single-tone buzzer 7-14VDC 150mA @ 12VDC 13,56Mhz ABA track 2 / Wiegand or RS232 MIFARE Plus S/X, DesFire EV1 -10...+40°C REED-relay sensor Separate NC contact or transmitted via communications line
*with ISO card in a noise-free environment
11
• • • •
MIFARE Classic / Ultralight MIFARE Plus X DESfire EV1 NFC compatibility
Main features • • • • •
High security Independent applications on a single tag (card) body NFC support Wall-mounting & desktop design Tamper protection
SEAWING
SC-1000 WebStar General Outlines
Main features Same construction Safety toroidal transformer Analogue output voltage stabilization Output current limit 12V & 24V accumulator compatibility Mains failure & over discharging battery indications Overload & short-circuit protection
• • • • • • •
Available models The PWS family of SEAWING power supplies has four members of different output current and voltages. PSW-12-10 – 12V 1A linear power supply PSW-12-20 – 12V 2A linear power supply PSW-24-20 – 24V 2A linear power supply
Specifications Type:
PWS12-1A
PWS12-2A
PWS24-2A
MEEI* certificate: Input Mains input: Rated current requirements: Mains transformers:
D0293E039
D0294E039
D0292E039
Mains connections: Output DC output voltages: Output voltages accuracy: Output voltages when recharging battery: Output current: Current limit Recommended sealed rechargeable batteries: Output connectors: Protection Shock protection: Overload protection: Battery protection: Fault indications: Tamper protection: Environment Operating temperature: Mechanical construction Case: Size: Weight:
230 V ±10% 50 Hz single-phase 150 mA 250 mA TL-30-1 TL-50-2 230/16V 230/16V Bolt fixing connectors Built-in thermostatic switch, MEEI licence No.: CM2594M025 13,8 V
13,8 V +2 ÷ 5 % 11,6 - 13,8 V
1A 1,3 A 12V / 7,2 Ah
400 mA TL-80-1 230/27V
27,6 V 23,2 -27,6 V
2A 2,3 A 12 V / 7,2 Ah
1,8 A 2,2 A 2x12 V / 7,2 Ah
Bolt fixing connectors Grounding, shock protection class No:1 (for built-in use only) Switch-off circuit for under 12V output voltages. under 24V Fuse protection for inverted polarity & overloading. Over discharging protection. 2 opto-coupling outputs, LED display for mains failure & over discharging battery Tamper switch -10 C° ÷+35 C° Metal case 200 x 100 x 70 mm 0,8 kg
1 kg
12
1,2 kg
