Transcript
SECTION 13750 VIDEO SURVEILLANCE SYSTEMS PART 1 GENERAL 1.1
SUMMARY A. B.
1.2
1.3
1.4
Section includes CCTV cameras, control equipment, and accessories. Related Sections: 1. Section 16130 – Raceway and Boxes. 2. Section 16710 – Telecommunications Systems. 3. Section 16711 – Local Area Network. 4. Section 16810 – Sound and Video Circuits: Video cable. 5. Section 16811 – Communications Cabinets, Racks and Enclosures.
SYSTEM DESCRIPTION A.
Description: Closed circuit television (CCTV) system providing real-time and archival digital video surveillance and monitoring of station/terminal activities at points as indicated on Drawings.
B.
Capacity: Closed circuit television (CCTV) system that is expandable and upgradeable to accommodate future equipment additions, facility expansion and renovation.
REFERENCES A.
Federal Communications Commission: 1. 47CFR15 – Radio Frequency Devices. 2. 47CFR68 – Connection of Terminal Equipment to the Telephone Network.
B.
Institute of Electrical and Electronics Engineers: 1. ANSI/IEEE C62.41 – Guide for Surge Voltages in Low-Voltage AC Power Circuits.
C.
National Fire Protection Association: 1. NFPA-70 – National Electrical Code.
D.
Telecommunications Industry Association/Electronic Industries Alliance: 1. ANSI/EIA 310-D – Cabinets, Racks, Panels and Associated Equipment. 2. TIA/EIA 568 – Commercial Building Telecommunications Cabling Standard. 3. TIA/EIA 569 – Commercial Building Standard for Telecommunication Pathways and Spaces. 4. TIA/EIA 607 – Commercial Building Grounding and Bonding Requirements for Telecommunications.
SUBMITTALS A.
Submit in accordance with General Provisions for Construction.
NPS Platform “E” Communications & Finishes Renovations
13750 - 1
Video Surveillance Systems
1.5
1.6
1.7
1.8
B.
Shop Drawings: Indicate electrical characteristics and connection requirements, including system wiring diagram at CCTV locations.
C.
Product Data: Submit catalog data showing electrical characteristics and connection requirements for each component.
D.
CAT5E test results prior to camera installation.
CLOSEOUT SUBMITTALS A.
Submit in accordance with General Provisions for Construction.
B.
Project Record Documents: Record actual locations of cameras and routing of television cable.
C.
Operation and Maintenance Data: Submit instructions for operating system and performing routine trouble shooting procedures.
QUALIFICATIONS A.
Manufacturer: Company specializing in manufacturing products specified in this section with minimum ten years documented experience, and with service facilities within 50 miles of project.
B.
Supplier: Authorized distributor of specified manufacturer.
C.
Installer: Authorized installer of specified manufacturer with minimum ten years documented experience.
PRE-INSTALLATION MEETINGS A.
Convene in accordance with General Provisions for Construction.
B.
Convene minimum one week prior to commencing work of this section.
ENVIRONMENTAL REQUIREMENTS A.
1.9
FIELD MEASUREMENTS A.
1.10
Conform to manufacturer’s standard service conditions during and after installation of components.
Verify field measurements prior to fabrication.
MAINTENANCE SERVICE A.
Furnish service and maintenance of video surveillance system equipment for one year from Date of Substantial Completion.
NPS Platform “E” Communications & Finishes Renovations
13750 - 2
Video Surveillance Systems
PART 2 PRODUCTS 2.1
SYSTEM PLATFORM A.
Manufacturer: 1. NICE Systems, Inc., “NiceVision NVR” Version 10.8 2. Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction. 3. Description: The Real-Time Network Video Recording System (RT-NVRS) shall not utilize any multiplexing or time-division technology for IP video. 4. All video information supplied from all edge devices shall be real time encoded and transmitted over an IP network simultaneously at resolutions of up to 4CIF and recording rates of up to 30 Frames per second (fps) NTSC or 25 fps PAL per camera. 5. The RT-NVRS shall be capable of supporting Mega-Pixel cameras: 1.3MP, 2MP, 3MP and 5MP. 6. The RT-NVRS shall be based upon a fully modular architecture, which allows for upgrades for additional recording capacity in the future. 7. The system shall simultaneously display live, playback and record video while continuously recording onto the system’s Hard-Drive(s) and archiving to remote storage server. 8. None of the video operations shall interfere with each other. 9. Recording operation shall not stop for playback or live viewing. 10. The RT-NVRS shall support several hardware platforms, each optimized for different number of channels.
B.
Recording Capacity: a. NVR Quantity: 0 b. IP Camera Inputs per NVR: 0 cameras. c. Nice 8 Channel Encoders per NVR: 0 d. Nice 2 Channel Encoders per NVR: 0 e. Dry Contact Interfaces: 0 d. Audio Inputs per NVR: 0 2. Video Processing and Compression: a. Standard Compression: ITU-T. b. Compressions: MPEG4 main profile; H.264, M-JPEG. c. Compression Rates: 16 Kbps to 4,096 Kbps, selectable per camera. 3. Frame Rates: 15 fps NTSC Input/Output: a. Analog Composite Video Input: NTSC/PAL, 75 ohms. b. IP Capture Compatibility: IP camera and converters. c. Output OSD: Time, date, camera name/number, view status. d. Application Programming Interface: 32-bit. 4. Video Event Triggers: a. Video motion detection per camera. b. Directional motion detection (based on object tracking technology). c. Content analysis: 1) Drop Bag Detection: 0 cameras 2) Crowd Detection: 0 cameras 3) Passenger Counting: 0 cameras 4) Illegal Park Car: 0 cameras 5. Pop-up video upon alarm.
NPS Platform “E” Communications & Finishes Renovations
13750 - 3
Video Surveillance Systems
6. 7. 8. 9. 10. 11.
12.
2.2
C.
Operating Characteristics: 1. Power Supply: 115/230 VAC, 60 Hz, single-phase. 2. Peak Power Consumption: 2.5 amps, 550 watts. 3. Power Dissipation: 1,000 to 1,300 Btu. 4. Operating Temperature: 40 to 110ºF. 5. Operating Humidity Level: 20 to 80%, non-condensing.
D.
Physical Specifications: 1. Dimensions: 7.0”H x 19.0”W x 23.5”D. 2. Net Weight: 77 lbs.
MINI-DOME CAMERAS A.
2.3
Video Software PTZ Software: Yes Audio Compressions: PCM; ADPCM-16. The NVR shall support 2 separate network interface cards (NICs). Each NIC shall support 10/100/1000Mbps Ethernet interface. Storage Media and Architecture: a. Internal Hard Drive Storage: 1 TB. b. External RAID Storage: 45-day storage for each camera at 15 fps per camera at 4CIF resolution, 80% activity, 10% PTZ/DVR. c. Disk Array Configurations: RAID-5. Search Capability: Event-driven and time-driven searches based on multiple criteria: a. Camera name/number. b. Date and time. c. Alarm trigger. d. External data. e. Comments. f. “Motiontrak” offline motion tracking tool.
Manufacturer: Bosch Security Systems, Inc., Models VDN-498 Series Camera or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction.
C.
Description: Vandal-resistant Mini-Dome, indoor or outdoor, pendant, wall, ceiling, mast mounted high-resolution color digital video camera. 1/3 inch wide dynamic CCD sensor, NTSC standard, cast aluminum housing, IP66 standard, day/night capabilities, privacy masking and remote communication capabilities to check camera status, upgrade firmware and change camera settings
D.
Lens: Wide angle 2.8 - 10.0 mm with automatic iris.
IP FIXED MINI DOME CAMERAS A.
Manufacturer: Axis: Mini Dome Series Model P33 Series Camera or approved equal.
NPS Platform “E” Communications & Finishes Renovations
13750 - 4
Video Surveillance Systems
2.4
2.5
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction.
C.
Description: Vandal-resistant, fixed position IP color digital 720p HD video camera with multiple H.264 video streams, remote zoom, Power over Ethernet, on-screen display, menu-based control system, digital signal processing, automatic black level control, low light level mode, and automatic white balance tracking. With the “Mini Dome Drop Ceiling Mount Plate” and the “Mini Dome Flush Mounting Plate”
D.
Lens: mount 3.3-12 mm
PTZ CAMERAS A.
Manufacturer: Axis Inc: PTZ Model Q- Series Camera or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction.
C.
Description: Outdoor, pendant, wall, ceiling, mast mounted 1080p high-definition color, 30 fps, 20x zoom, day/night PTZ camera.
POWER SUPPLY/16-CHANNEL PASSIVE VIDEO RECEIVER A. B. C.
2.6
2.7
Manufacturer: Network Video Technologies, Inc., Model NV-16PS13-PVD or approved equal. Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction. Description: 16 channel passive video distribution amplifier and power supply for transmission of real-time video signals; with output per channel; integral ground lifting and transient protection; RJ-45 for UTP wire connection; female BNC connections for coaxial cable; adjustable sharpness and brightness trim pot controls for each channel; and coaxial jumper cables for each channel.
FIBER SWITCH A.
Manufacturer: AFI Inc, Model Commander Series or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction
C.
Description: Fully managed 8 port 802.3af PoE with full power available at each port with no power sharing network switch. 10 port fully managed level 2 network switch with 2, 1 Gigabit ports for Cascade and VLAN configurations.
FIBER MULTI-CHANNEL TRANCEIVERS A.
Manufacturer: AFI Inc, Model Transceiver Series or approved equal.
NPS Platform “E” Communications & Finishes Renovations
13750 - 5
Video Surveillance Systems
2.8
2.9
2.10
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction
C.
Description: Fully managed 16-port transceiver that transmits and receives individual channels of video. The ability to transmit and receive data communications for PTZ control.
POWER SUPPLY A.
Manufacturer: Pelco Inc: WCS Series Power Supply or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction
C.
Description: Outdoor camera power supply, 100/120/240 VAC input, One 24, 26, 28 VAC output, total current capacity of 4A (100VA)
PASSIVE VIDEO TRANSMITTER A.
Manufacturers: Bosch, Inc., Model VDN-455UTP or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction.
C.
Description: Passive, non-amplified video transmitter for transmission of real-time composite video signals over unshielded twisted pair telephone wiring; with coaxial lead; integral interference rejection and transient protection; UTP screw terminals, and inline male BNC connector.
PATCH PANEL A.
Manufacturer: Ortronics, Model OR-PSD5E6U48 or approved equal.
B.
Substitutions: Submit requests for substitution in accordance with the General Provisions for Construction.
C.
Description: 48-port panel, Cat 5e, STD density, six-port modules, 19" x 10.5"
PART 3 EXECUTION 3.1
EXAMINATION A.
Verify existing conditions prior to beginning work.
B.
Verify that outlet boxes for mounting cameras are installed at proper locations.
C.
Verify that branch circuit wiring installation is completed, tested, of proper voltage and operating characteristics, and ready for connection to CCTV equipment.
NPS Platform “E” Communications & Finishes Renovations
13750 - 6
Video Surveillance Systems
3.2
3.3
3.4
EXISTING WORK A.
Disconnect and remove abandoned video surveillance equipment.
B.
Extend existing video surveillance installations using materials and methods as specified.
C.
Clean and repair existing video surveillance equipment remaining or to be reinstalled.
GENERAL INSTALLATION A.
Install in accordance with manufacturer's instructions and as indicated on the Contract drawings.
B.
Install cameras at locations and heights as indicated on the Contract drawings. Change type of mounting as necessary to achieve required clearance where approved in advance by NJT personnel. The camera views shall not be obstructed by any architecture, structural, or signage elements.
C.
Coordinate locations of outlet boxes specified in Section 16130 to obtain mounting heights as indicated on Contract drawings .
D.
Install cable and wire as specified in Section 16810.
E.
Set pan unit and pan-and-tilt unit stops to suit final camera position and to obtain the field of view required for camera in accordance with approved shop drawings and calculations.
F.
Install power supplies and other auxiliary components at control stations. Do not install such items near the devices they serve, unless otherwise indicated.
G.
Install equipment racks in accordance with ANSI/EIA 310 in locations shown on Contract drawings; arrange for adequate ventilation and access. Refer to Section 16811.
H.
Ground and bond CCTV system equipment in accordance with Section 16060 and TIA/EIA 607.
I.
Identify system components, wiring, cabling, and terminal connections. Refer to Section 16195.
CONDUIT INSTALLATION: A.
Supply and install new GRS conduit and associated hardware as indicated on the contract drawings.
B.
All new GRS conduit to be a minimum of 1” in diameter.
C.
New conduit shall be installed within 3’ of each CCTV location. The contractor shall provide and install liquid tight conduit and the necessary hardware from the end of the GRS conduit to camera housing.
NPS Platform “E” Communications & Finishes Renovations
13750 - 7
Video Surveillance Systems
D. 3.5
No exposed cabling will be permitted.
STATION COMMUNICATION ROOM HARDWARE INSTALLATION: A.
Install the following in the communication room: 1. 2. 3. 4. 5. 6.
7.
8. B. 3.6
(1) 48 Port Patch Panel (3) Power supply cable integrator hub (1) Midspan KVM Switch/Console NVR, Raid Units and encoders Supply and install the necessary number of 4-pair category 5e patch cord cables from the patch panel to the power supply cable integrator hub that will support the quantity of cameras shown on the contract drawings Supply and install the necessary number of 4-pair category 5e patch cord cables from the patch panel to the midspan and from the midspan to the network switch. Supply and install the necessary number of 4-pair category 5e patch cord cables from the NVR to the network switch.
Install NVR as per NiceVision specifications for NVR installation. Contractor supply all necessary mounting hardware and shelves for proper installation of NVR.
CAMERA INSTALLATION: A.
The contractor shall use the design to determine the adequacy of the design and, in conjunction with a field survey and NJT personnel, determine the exact location of each CCTV camera.
B.
Install in accordance with manufacturer’s instructions and as indicated on the reference drawings.
C.
Install cameras at locations and heights as indicated on the Contract drawings. Change type of mounting as necessary to achieve required clearance where approved in advance by Engineer.
D.
Install camera, lens and video balun into each CCTV enclosure and configure per manufacturers instructions.
E.
Each camera shall have a single dedicated category 5e cable point-to-point without any splices from each camera to the station communication room patch panels.
F.
Within the camera housing terminate the category 5e cable with an RJ-45 connector in accordance with EIA/TIA 568B specifications and connect to video balun.
G.
Label cable at both camera and communication cabinet ends with camera designation number on drawing.
H.
Label (camera number), terminate and test all new Cat-5e cable to new cameras as shown on drawings.
NPS Platform “E” Communications & Finishes Renovations
13750 - 8
Video Surveillance Systems
3.7
MANUFACTURER'S FIELD SERVICES A.
3.8
3.9
Furnish manufacturer’s field representative to supervise final wiring connections and system adjustments.
ADJUSTING A.
Align and adjust system and pretest components, wiring, and functions to verify that they comply with specified requirements. Adjust lens irises to meet lighting conditions. Replace malfunctioning or damaged items. Retest until satisfactory performance and conditions are achieved.
B.
Where system performance is degraded in certain operating modes, revise component connections and install video distribution amplifiers and/or attenuators as required to provide a balanced signal across the system.
DEMONSTRATION AND TRAINING A.
B.
Furnish eight (8) hours of instruction each for up to ten (10) NJ TRANSIT staff, to be conducted at project site with manufacturer's representative. Coordinate training schedule with Construction Manager, Engineer and manufacturer. Provide minimum of ten (10) days notice prior to proposed commencement of training. Instruct NJ TRANSIT staff on how to adjust, operate, and maintain CCTV system equipment: 1. Review procedures and schedules for troubleshooting, servicing, and maintaining equipment. 2. Demonstrate methods of determining optimum alignment and adjustment of components and settings for system controls. 3. Review data in maintenance manuals.
PART 4 COMPENSATION 4.1
MEASUREMENT AND PAYMENT A.
Measurement: The work of this section shall not be measured.
B.
Payment: The cost of this section shall be included in the lump sum bid item CCTV SYSTEMS, with separate pricing provided for LABOR and MATERIALS. END OF SECTION
NPS Platform “E” Communications & Finishes Renovations
13750 - 9
Video Surveillance Systems
