Sena | 10s | Quick Start Guide | Preparation Basic Operation Pairing

Transcript

PREPARATION BASIC OPERATION Knowing the Headset Layout Installing the Headset Headset PAIRING Operating the Buttons Speaker Checking the Battery Level Jog Dial 1 Clamp Unit 2 1 Charging LED Tap the button 2 Phone Button Double tap the button Left Press and hold the button for 5 seconds Press the two buttons at the same time Rotate the Jog Dial Right 3 ON 1 1 Headset Left Speaker Connector Earbud Port Right Speaker Connector You will hear descending beeps. “Good bye” MP3 Port Microphone Connector OFF Microphone 3 “Hello” 1 2 Clamp Unit You will hear ascending beeps. 2 Simultaneously press and hold the Jog Dial and the Phone Button for 1 second to turn on or off the headset. Blinking 70~100% Blinking 30~70% Blinking 0~30% “High” 70~100% “Medium” 30~70% “Low” 0~30% Or, press and hold the Jog Dial and the Phone Button for 3 more seconds when the headset turns on. You will hear a triple beep and a voice prompt. Charging the Battery  You will hear a beep when the volume reaches the maximum or minimum level. or “Hello”   “Phone pairing” Ending Calls Rejecting Calls or Bluetooth Bluetooth   until you hear a beep   “Your headset is paired” Charging Fully charged or 1 or Sena10S 2 Adjusting the Volume Answering Calls Turn on the headset and check the battery level via the Status LED. Turning On/Off the Headset DC Power Charging & Firmware Upgrade Port Using Phone Features After Pairing… 5 Status LED Pairing with Mobile Devices - Phone, Music AC adapter Making Calls Using the Phone Keypad   until you hear a beep Using the Voice Dialer Using the Speed Dial INTERCOM RADIO SETTING TROUBLESHOOTING Pairing with Other Headsets Turning On/Off the FM Radio Method1) Using the headset Factory Reset Headset A Headset B 1 You will hear a double beep sound. You will hear a double beep sound. “FM on” or “FM off” “Configuration menu” If you want to restore the 10S to factory default settings, press and hold the Phone Button for 10 seconds. Tap the Jog Dial. The headset automatically restores the default settings and turns off. Fault Reset You will hear a beep. “Speed dial” Voice Menu • Last number redial • Speed dial 1 • Speed dial 2 • Speed dial 3 • Cancel   “Intercom pairing” Seeking Stations Listening to Preset Stations Connect the headset to your computer via a USB cable. Launch the Sena Device Manager and click DEVICE SETTING to configure the headset settings. Listening to Music  until you hear a double beep 1 Tracking Forward or Backward Rotate While Pressing Quick Start Guide For details about downloading the Sena Device Manager, refer to the leaflet included in the package. After Pairing… Playing or Pausing Music Method2) Using the Sena Device Manager If the 10S is not working properly for any reason, push the pin-hole reset button located on the back of the headset. Follow the steps above to pair with two or more headsets. Rotate While Pressing Method3) Using the Sena Smartphone App Saving or Deleting Stations Using the Intercom To Save After Pairing… To Delete 1. On your smartphone, download the Sena Smartphone App for Android or iPhone from Google Play or App Store. Refer to www.sena.com/headset-app/ for more details. 1 2. Pair your smartphone with the headset. 2 3. Run the Sena Smartphone App. Swipe the screen to the right and tap Setting to configure the headset settings. 3 “Preset (#)” You can start or end a two-way intercom conversation with each headset. Motorcycle Bluetooth® Communication System “(#)” “Save preset (#)” “Delete preset (#)” Sena Technologies, Inc. www.sena.com Customer Support: support.sena.com E-mail: [email protected] You can download the full version of the manual and view other Sena products at the Sena website: www.sena.com. 16.Feb