Transcript
Serene ‘Classic’ Rails
PRN2169 Rev. 4.0 Aug. 2013
User Manual
Heated Ladder Towel Rails - Curved
Contents 1 Safety Information ........................ 3 2 Installation .................................. 4 Wiring .............................................. 4 Distances ......................................... 4 To Install the Towel Rail ..................... 4 3 Operation .................................... 7 4 Specifications ............................... 7 Dimensions ........................................... 7 Electrical ............................................. 7 Construction .......................................... 7
5 Maintenance ............................... 8 6 Contact Addresses . . . . . . . . . . . . . . . . . . . . . 8
Copyright © 2013 Serene Industries Limited. Serene Industries Limited reserve the right to alter specifications without notice.
Classic Series
2
SERENE Heated Ladder Towel Rails
1 Safety Information When using any electrical appliance, safety precautions should always be observed. Read these instructions carefully before installation and retain for future reference.
This appliance is intended to dry towels and therefore is hot to the touch. When used by or near young children or infirm persons, close supervision is necessary. Young children should be supervised to ensure that they do not play with the appliance.
Any rise in ambient temperature is directly reflected in the appliance and as a result of this the appliance will feel hotter to the touch during warmer periods. The insulation effect of towels will also cause the operating temperature to increase.
Use this appliance only on the voltage specified on the rating label.
Regulations require that electrical work be carried out only by authorised persons. For your own safety, and that of others, ensure this is done.
To avoid a hazard for young children, this appliance MUST be installed so that the bottom rail is at least 600mm above the floor.
To avoid a hazard this heated towel rail MUST NOT be used to carry towels or any other articles that have been in contact with oil, petroleum based products or dry cleaning fluids.
Do NOT use this appliance other than for its intended use.
Do NOT immerse in any liquid.
Do NOT allow the power supply cord to come into contact with heated surfaces during operation.
Caution: If this appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set or electrical portable device must be positioned so that it is not subject to splashing or ingress of moisture.
Classic Series
3
SERENE Heated Ladder Towel Rails
2 Installation This appliance MUST be installed in accordance with the relevant wiring rules and regulations which cover installation of appliances and accessories in damp situations such as bathrooms, showers, laundries and other areas with fixed water containers (in Australia and New Zealand - AS/NZS 3000: 2000 Wiring Rules).
Wiring The Heated Ladder Towel Rail is supplied with a 900mm supply cord and plug. This Class II appliance does NOT require Earthing. Where protected by an RCD, the Heated Towel Rail can be plugged directly into a socket outlet, otherwise permanent connection to the supply via a permanent connection unit is required. On directly wired models, a suitable disconnection device (acting in all supplies) MUST be incorporated in the fixed supply wiring.
Distances In order to avoid a hazard for young children, this appliance MUST be installed so that the bottom rail is at least 600mm above the floor. The side frames of the Towel Rail should be mounted vertically, with the heated rails horizontal and the supply cord at the bottom.
To Install the Towel Rail 1.
2.
Remove all the packing material from around the towel rail and retrieve the fixing screws and adhesive dots from inside the plastic bag taped to the power cord. Establish a suitable position on the wall for attaching the towel rail, with at least two of the leg mounting brackets aligned with wall studs or dwangs.
Classic Series
4
SERENE Heated Ladder Towel Rails
3.
Remove all four of the mounting brackets from the towel rail frame by undoing the small hexagon socket screw under each leg. Be careful not to lose the screws.
4.
Mark the location of ONE of the mounting brackets on the wall.
5.
Drill a hole centrally at the marked location and fix the mounting bracket to the wall, either using a wall fixing screw (supplied) or a suitable wall fixing plug.
6.
Attach one of the adhesive dots (supplied) to the back of each of the remaining three mounting brackets and remove the protective paper backing.
7.
Insert the remaining three mounting brackets into the frame mounting legs. Ensure the rectangular fixing slot, in each mounting bracket, faces downwards so as to correctly align with the fixing hole in each of the frame legs.
5
Classic Series SERENE Heated Ladder Towel Rails
8. Position the corresponding towel rail frame leg onto the mounting bracket already attached to the wall. If necessary, use a level to align the towel rail in the desired position, before pressing firmly against the frame to adhere the remaining three mounting brackets to the wall.
9. Pull the frame away, leaving the mounting brackets attached to the wall.
10. Drill and attach the remaining three mounting brackets to the wall using either the three wall fixing screws (supplied) or suitable wall fixing plugs.
11. Refit the towel rail frame over the mounting brackets and lock in place with the four small hexagon socket screws.
12. Either connect the supply cord to a socket outlet or, if installed in a bathroom, have an authorised person connect the supply cord to a switched permanent connection unit.
Classic Series
6
SERENE Heated Ladder Towel Rails
3 Operation The Heated Ladder Towel Rail will take approximately 45 minutes to reach normal operating temperature and, if need be, can be left running continuously. The Heated Ladder Towel Rail costs approximately the same to run as a 100 Watt light bulb.
4 S pe c i f i ca t i on s Dimensions Model
SLTR5SS
SLTR7SS
SLTR9SS
SLTR11SS
Height:
560mm
805mm
1040mm
1280mm
Width:
630mm
630mm
630mm
630mm
Depth:
125mm
125mm
125mm
125mm
Weight:
2.0 kg
2.5 kg
3.1 kg
3.8 kg
87-95 W
105-115 W
Electrical Supply:
230-240 Volts a.c. 50 Hz
Wattage:
45-50 W
65-70 W
Insulation Class: Class II - Double Insulated Wiring:
900mm 2-core supply cord and plug. The plug may be removed for connection to permanent wiring.
Controls:
No controls provided. Designed for continuous operation. The LED indicates when the towel rail is operating.
Construction Ingress Protection Rating: IP34 – Splash proof Finish:
Polished stainless steel frame, with chrome plated fittings, and white supply cord and plug.
Table 1: Specifications
7
Classic Series SERENE Heated Ladder Towel Rails
5 Maintenance The Heated Ladder Towel Rail is best wiped down from time to time with a damp cloth. Do NOT use any abrasive or corrosive cleaners. The supply cord on this product cannot be replaced without damaging the appliance. If the supply cord becomes damaged in any way, the appliance should be scrapped. If the appliance is under warranty, contact Serene Industries Limited.
6 C ont act Add r es se s NEW ZEALAND Serene Industries Limited t:+64 (3) 344 5560 f: 0800 437 264 e:
[email protected] w: www.serene-ind.com PO BOX 33501, Barrington, Christchurch 8024 AUSTRALIA e:
[email protected] w: www.serene-ind.com HONG KONG t: +852 2325 3210 f:+852 2325 3166 e:
[email protected] w: www.serene-ind.com Serene Industries Limited 1508, 15th Floor, 9 Wing Hong Street, Cheung Sha Wan, Kowloon Hong Kong
8
Classic Series SERENE Heated Ladder Towel Rails
