Series Lfusg-b Lead Free

Transcript

ES-LFUSG-B For Residential and Commercial Applications Job Name_______________________________________ Contractor_______________________________________ Job Location_____________________________________ Approval_________________________________________ Engineer_________________________________________ Contractor’s P.O. No._ ____________________________ Approval_________________________________________ Representative_ __________________________________ LEAD FREE* Series LFUSG-B Under Sink Guardian® Series LFUSG-B Under Sink Guardian® 3⁄8" (10mm) compression fitting ther­mo­stat­ic mix­ing valves maintain and limit hot water to desired se­lect­able temperature between 80°F and 120°F (27°C and 49°C) with flow rates as low as 0.5 gpm (1.9 lpm) and as high as 2.5 gpm (9.5 lpm). The mix­ing valve is listed to ASSE Standard 1070 for sin­gle fix­ture applications. The LFUSG-B se­ries uses a dou­ble throt­tling de­sign to control both the hot and cold wa­ter sup­ply to the mixed outlet.The LFUSG-B features Lead Free* construction to comply with Lead Free* installation requirements. The su­pe­ri­or flow char­ac­ter­is­tics of this valve provide ac­cu­rate tem­per­at­ure con­trol (±3°F) with low pres­sure drop. As an add­ed fea­ture, the LFUSG-B -M1 in­cor­po­rates dual check valves to pro­tect against cross-flow and integral screens to filter out debris. Features • Lead Free* Brass body construction. • Maintains mixed water temperature to ±3°F up to 120°F (49°C). • Installs easily between the stop valves and faucet • Includes tamper resistant locking cap to prevent accidental mis-adjustment. • Built-in check valves prevent migration of hot water to cold and cold water to hot water piping. • Provided with cap for three port application. • Integral strainer with 40 mesh stainless steel screens to filter out debris. Applications The unit is intended for under sink installation to con­trol the hot water temperature and prevent ac­ci­den­tal scald­ing. The water temperature must be adjusted by the in­stall­er using a thermometer to measure the hot water tem­per­at­ure at the faucet outlet. Maximum tem­per­a­ture of 110°F (43°C) is recommended. LFUSG-B-M1 ASSE 1070 Listed U.S. Pat. 6,315,209 Application Note Delivery of water to fixtures intended for use in bath­ing or wash­ ing should always be controlled by valves listed to ASSE Stan­ dard 1016 or ASSE Standard 1070 such as Watts Series LFUSG or LFMMV mixing valves. These valves provide the user with both scald pro­tec­tion and pro­tec­tion from thermal shock. The installer should always test to verify temperature setting after installation. Materials Body: Lead Free*Brass Metal Disc: Stainless steel Spring: Stainless steel Ball: Stainless steel Rubber Disc: Buna-N O-rings: Buna-N Piston: UDEL-P1700 Thermostat: Copper Approval ASSE 1070 CSA B-125 Specifications A Thermostatic Mixing Valve shall be installed on the hot water supply to the fix­ture. The valve shall be ASSE Standards 1070 listed and control the temperature of the hot water. It shall have a Lead Free* brass body. Body shall be constructed using Lead Free* Brass. Lead Free* under counter thermostatic valves shall comply with state codes and standards, where applicable, requiring reduced lead content. The valve shall include integral check valves, integral screens and an ad­just­ment cap with lockin fea­ture. The valve shall be pro­vid­ed with 3⁄8" (10mm) male com­pres­sion fittings. The valve shall be Watts Series LFUSG-B. For satin chrome finish specify – SC. *The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight. Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold. Pressure – Temperature Basic Construction Minimum supply pressure: 30psi (207 kPa) Button Head Screw Hot inlet temperature: 120°F-180°F (49°C-82°C) Locking Adjusting Cap Ball O-ring Cold inlet temperature: 39°F-80°F (3.8°C-27°C) Minimum inlet temperature differential: 15°F (9°C) Temperature out: 80°F-120°F (27°C-49°C) Stem Thermostat Metal Disc Check module Maximum pressure: 150psi (10.3 bar) Maximum Pressure differential between hot and cold inlet supplies: 25%. Piston O-ring Mesh Screen Spring Body Flow Capacity 3⁄8" LFUSG-B-M1 Check Module A B kPa 620 551 482 413 345 276 207 138 69 0 psi 90 80 70 60 50 40 30 20 10 0 0 0 1.00 3.8 2.00 7.8 3.00 11.4 4.00 gpm 15.2 lpm Dimensions – Weights Models LFUSG-B-M1 LFUSG-B-SC*-M1 in. A mm in. mm Weight lbs. kgs. ⁄ " Comp. 35⁄64 ⁄ " Comp. 35⁄64 78 78 53⁄16 53⁄16 132 132 1.0 1.0 Size 38 38 B .45 .45 * SC – Satin Chrome Finish Typical Installations Two Handle Faucet Sensor Faucet LFUSG-B-M1 A Watts Water Technologies Company USA: No. Andover, MA • Tel. (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com Canada: Burlington, ONT. • Tel. (905) 332-4090 • Fax: (905) 332-7068 • www.wattscanada.ca ES-LFUSG-B 1101 © 2011 Watts