Transcript
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
PAUL REDEHOFT
Home | Account | Contact ALLDATA | Log Out | Help
Select Vehicle | New TSBs | Technician's Reference
Page 1 of 8
OK
Component Search:
Conversion Calculator
1995 Honda Accord Sedan V6-2.7L SOHC Vehicle Level
Engine, Cooling and Exhaust
Engine
Timing Belt
Service and Repair
Service and Repair Notes
Zoom
Sized for Print
TIMING BELT REMOVAL
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Page 2 of 8
NOTE:
Mark the direction of rotation on the belt before removing. Do not use the upper covers and lower cover for storing removed items. Clean the upper covers and lower cover before installing. Replace the camshaft seals and crankshaft seals if there is oil leakage. Refer to crankshaft pulley before installing timing belt. Replace the timing belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle regularly is driven in one or more of the following conditions, replace the timing belt at 60,000 miles (100,000 km): In very high temperatures (over 110°F, 43°C). In very low temperatures (under -20°F, -29°C). Turn the crankshaft pulley so the No. 1 piston is at top dead center (TDC) before removing the belt. Inspect the water pump after removing the timing belt.
1. Remove the front wheels and splash shield. 2. Remove the bolts, then loosen the mount bolt and pivot the side engine mount out of the way. 3. Loosen the idler pulley center nut and adjusting bolt, then remove the air conditioning (A/C) compressor belt. 4. Loosen the alternator mounting bolt, nut and adjusting bolt, then remove the alternator belt. 5. Loosen the mounting nuts and adjusting nut, then remove the power steering (P/S) pump belt.
Zoom
Sized for Print
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Page 3 of 8
6. Remove the dipstick and pipe. 7. Remove the crankshaft pulley.
Zoom
Sized for Print
8. Remove the upper covers and lower cover. NOTE: Do not use the upper and lower covers for storing removed items. 9. Loosen the adjusting bolt 180°. Push the tensioner to remove tension from the timing belt, then retighten the adjusting bolt.
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Zoom
Page 4 of 8
Sized for Print
10. Remove the timing belt. TIMING BELT INSTALLATION NOTE:
Install the timing belt in the reverse order of removal; Only key points are described here. Clean the upper and lower covers before installation.
Zoom
Sized for Print
1. Set the timing belt drive pulley so that the No. 1 piston is at TDC. Align the TDC mark on the tooth of the timing belt drive pulley with the pointer on the oil pump. Front
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Zoom
Page 5 of 8
Sized for Print
Rear
Zoom
Sized for Print
2. Set the camshaft pulleys so that the No. 1 piston is at TDC. Align the TDC marks on the camshaft pulleys to the pointers on the back covers.
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Zoom
Page 6 of 8
Sized for Print
3. Install the timing belt tightly in the sequence shown: (1) Timing belt drive pulley (crankshaft) (2) Adjusting pulley (3) Front camshaft pulley (4) Water pump pulley (5) Rear camshaft pulley NOTE: Make sure the timing belt drive pulley and camshaft pulleys are at TDC. 4. 5. 6. 7.
Loosen and retighten the adjusting nut to tension the timing belt. Install the lower cover and upper covers. Install the crankshaft pulley, then tighten the pulley bolt. Rotate the crankshaft pulley about 5 or 6 turns clockwise so that the timing belt positions on the pulleys. 8. Adjust the timing belt tension.
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Zoom
Page 7 of 8
Sized for Print
9. Check that the crankshaft pulley and camshaft pulleys are at TDC. Front
Zoom
Sized for Print
Rear
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
ALLDATA Online - 1995 Honda Accord Sedan V6-2.7L SOHC - Service and Repair
Zoom
Page 8 of 8
Sized for Print
10. If the camshaft or crankshaft pulley is not positioned at TDC, remove the timing belt and adjust the positioning, then reinstall the timing belt. NOTE: After installation, adjust the tension of each belt.
© 2010 ALLDATA LLC. All rights reserved.
Terms of Use
http://www.alldatapro.com/alldata/PRO~V155086906~C21693~R0~OD~N/0/41746505/56... 3/1/2010
