Transcript
CDX-828 SERVICE MANUAL
US Model Canadian Model AEP Model UK Model E Model
Model Name Using Similar Mechanism
CDX-805
CD Drive Mechanism Type
MG-250C-137
Optical Pick-up Name
KSS-521A/J2N
SPECIFICATIONS
COMPACT DISC CHANGER MICROFILM
SECTION 1 SERVICING NOTES TABLE OF CONTENTS 1.
SERVICING NOTES ................................................ 2
2.
GENERAL ................................................................... 3 Installation ....................................................................... 4 Connections ..................................................................... 5
3.
DISASSEMBLY ......................................................... 6
4.
MECHANISM DECK ASSEMBLY ..................... 12
5.
MECHANICAL ADJUSTMENTS ....................... 14
6.
ELECTRICAL ADJUSTMENTS ......................... 15
7.
DIAGRAMS
7-1. Block Diagram – SERVO Section – ............................... 17 7-2. Block Diagram – MAIN Section – ................................. 19 7-3. Block Diagram – BUS CONTROL/POWER SUPPLY Section – ........... 21 7-4. Note for Printed Wiring Boards and Schematic Diagrams ....................................................... 24 7-5. Printed Wiring Boards – RF/SW Boards – ..................... 25 7-6. Schematic Diagram – RF/SW Boards – ......................... 27 7-7. Printed Wiring Board – MAIN Board (Component Side) – .............................. 29 7-8. Printed Wiring Board – MAIN Board (Conductor Side) – ................................ 31 7-9. Schematic Diagram – MAIN Board (1/3) – ................... 33 7-10. Schematic Diagram – MAIN Board (2/3) – ................... 35 7-11. Schematic Diagram – MAIN Board (3/3) – ................... 37 7-12. Printed Wiring Boards – DIGITAL OUT /JACK Boards – ................................. 41 7-13. Schematic Diagram – DIGITAL OUT /JACK Boards – ................................. 43 7-14. IC Pin Function Description ........................................... 49
8.
EXPLODED VIEWS ................................................ 52
9.
ELECTRICAL PARTS LIST ............................... 57
NOTES ON HANDLING THE OPTICAL PICKUP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. Laser Diode Properites • Material: GaAlAs • Wavelength: 780 nm • Emission Duration: continuous • Laser Output Power: less than 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat.
DISC MAGAZINE GETTING OUT PROCEDURE ON THE POWER SUPPLY IS OFF Remove the CASE (LOWER) assembly beforehand 1) Press the lever (ML) assy to arrow direction. 2) Removal the magazine assy.
SAFETY-RELATED COMPONENT WARNING!!
Note: Take out the magazine only when the tray is completely within the magazine. If the disk or tray is sticking out, turn on the power and eject the magazine.
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Lever (ML) ass’y
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Magazine ass’y
–2–
SECTION 2 GENERAL
–3–
This section is extracted from instruction manual.
–4–
–5–
SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given.
COVER (UPPER) , FRONT PANEL ASS’Y 1 screw (PTT2.6 × 6)
2 screw (BVTT2.6 × 6)
3 cover (upper)
4 lever (FL)
1 screw (PTT2.6 × 6)
1 screw (PTT2.6 × 6)
4 lever (FL)
5 front panel ass’y 1 screw (PTT2.6 × 6)
MECHANISM DECK (MG-250C-137) 4 mechanism deck (MG-250C-137) 2 tension spring (FL)
2 tension spring (FL) 1 two dampers (250)
3 jack flexible board (CN903)
1 two dampers (250)
–6–
JACK BOARD, DIGITAL OUT BOARD
2 connector (CN902) 5 connector (CN801)
Remove the jack board of the arrow.
1 ground point screw (PTT2.6 × 6) 3 jack board 6 digital out board 4 screw (BVTT2 × 6)
MAIN BOARD
1 main flexible board (CNJ12)
6 three screws (FP)
7 main board
2 connector (CN302)
3 screw (PTT2 × 3)
5 two precision screws (P1.7 × 2.5) 4 heat sink
–7–
ELEVATOR MOTOR ASS’Y (M104) 1 screw (PTT2 × 3) 2 bracket (EVM)
3 elevator motor ass’y (M104)
ESCUTCHEON (T)
3 two claws
2 Remove the claw of the arrow A.
A
B
4 Remove the ditch of the arrow B.
5 Remove the escutcheon (T) of the arrow C.
3 claw C 4 ditch
1 screw (M2 × 3)
–8–
CASE (UPPER) ASS’Y
1 three screws (PTT2 × 4)
3 Remove the edge of the arrow A.
A 2
1 two screws (PTT2 × 4) B
4 Remove the case (upper) ass’y of the arrow B.
1 screw (PTT2 × 4)
CHASSIS ASS’Y
3 chassis ass’y
1 two polyethylene washers 2
2
–9–
RF BOARD 1 OP flexible board (CNJ11)
2 two screws (PS2 × 4)
2 two screws (PS2 × 4) 3
5 RF board
4 connector (CNP52)
4 two connectors (CNP11, 53)
SLED MOTOR ASS’Y (M102) , OPTICAL PICK-UP (KSS-521A/J2N)
1 two screws (ESCUTCHEON)
2 sled motor ass’y (M102)
3 optical pick-up (KSS-521A/J2N)
4 Turn at the direction of the arrow, then remove shaft (sled) ass’y
– 10 –
SW BOARD, SPINDLE MOTOR ASS’Y (M101)
8 two screws (P1.7 × 2.2) 7
3 spring (chucking)
6 retainer (disc) 1 screw (P2 × 2.2) 5 bracket (CP)
4 screw (P2 × 2.2)
9 Remove the spindle motor ass’y (M101) of the arrow.
2 SW board
CHUCKING MOTOR ASS’Y (M103) 2 two screws (P2 × 2.5)
3 retainer (CHM) 4 chucking motor ass’y (M103)
1 connector (CNP51)
– 11 –
SECTION 4 MECHANISM DECK ASSEMBLY Note: Follow the assembly procedure in the numerical order given.
OPTICAL PICK-UP COMPLETE ASS’Y 1 Move the lever (LOCK 3) in direction A, and return it a little in direction B from the position where the chuck plate is moved down to the lower limit.
chuck plate
B A 4 stop ring 2.0 (E type)
5 tension spring (DH)
2 washer 2.5
3 optical pick-up complete ass’y Note: Insert the shaft (A) first.
shaft (A)
GEAR (LOMINI) / (LOAD 1) ASS’Y 2 Attach the gear (LOMINI) at the position shown in Fig. A.
gear (LOAD 2)
gear (LOMINI)
shaft (rotary prevention C) chuck plate
B
1 Move the lever (LOCK 3) fully in direction B to move the chuck plate up.
marking Fig. A
slit 3 Attach the gear (LOAD 1) ass’y with its facing inside. 4 stop ring 1.5 (E type)
– 12 –
OPERATION CHECK 1 Confirm that the slider moves in direction C to move down the chuck plate if the gear (LOAD 1) is rotated in direction A or the chuck plate moves up and the slider moves in direction D if the gear is rotated in direction B.
slider chuck plate
D
C
A
B
gear (LOAD 1) ass'y
– 13 –
SECTION 5 MECHANICAL ADJUSTMENTS • Elevator Height (Address) Adjustment Adjustment Method: 1. Connect this set to the master unit (e.g. MDX-C670/ C670RDS), load a disc magazine, and place the set vertically as shown below.
Note: This adjustments is necessary when the system controller (IC201), variable resistor (RV201), slider (R), slider (L), or chassis (ELV) was replaced for any repair.
Connection:
2. Connect the regulated power supply to the master unit, and turn the power on.
power supply master unit
3. Press the DISC button on the master unit and select DISC 5.
+ GND
4. At this time, if the elevator shaft does not position between comb teeth A and B at addresses 5 and 6 as shown below, adjust the following. 5. Press repeatedly the DISC + and – buttons on the master unit so that the elevator shafts moves from address 6 to address 5, or from 5 to 6. At this time, adjust RV201 on the main board so that the elevator shaft positions smoothly between comb teeth A and B.
BUS cable
6. Further, place the set horizontally and make same adjustment as mentioned above. 7. After adjustment at addresses 5 to 6 is finished, check all operations from addresses 1 to 10 with the set placed vertically and horizontally respectively to confirm that the elevator shaft positions in a range between comb teeth A to B.
CDX-828
comb tooth at address 6
comb tooth at address 6 elevator shaft
A
A
B
B
elevator shaft
comb tooth at address 5 comb tooth at address 5
OK
RV201
– 14 –
NG
SECTION 6 ELECTRICAL ADJUSTMENTS Note: 1. Perform adjustments as given. 2. Power supply voltage: DC14.4 V (more than 3A).
• TRACKING OFFSET CHECK [RF BOARD] – Conductor Side –
oscilloscope
• FOCUS BIAS CHECK CNJ12 [RF BOARD] – Conductor Side –
+ –
CNJ12 TP (RF)
IC51
oscilloscope + –
BP11 (TE)
IC51
TP (VC) IC11
TP (VC) IC11
Procedure: 1. Connect the oscilloscope to TP (RF) and TP (VC) on the RF board. 2. Put the set into play mode by loading the disc. 3. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
Procedure: 1. Connect the oscilloscope to BP11 (TE) and TP (VC) on the RF board. 2. Put the set into play mode by loading the disc. 3. Press the = AMS + button, and check the traverse waveform*. 4. Confirm that the oscilloscope waveform is symmetrical on the top and bottom in relation to 0 V dc, and check this level.
Note: Clear RF signal waveform means that the shape “≈” can be clearly distinguished at the center of the waveform.
* Traverse waveform: This is the tracking error wave form appears when crossing the track.
Traverse waveform
RF signal waveform VOLT/DIV: 200 mV TIME/DIV: 500 ns
VOLT/DIV : 500 mV TIME/DIV : 2 ms Center : 0 V
A 0V B
level: 1.4 ± 0.3 Vp-p A=B traverse waveform (100 track jump waveform)
– 15 –
• FOCUS GAIN ADJUSTMENT (COARSE ADJUSTMENT) This adjustment is to be performed when replacing the following parts. • Optical Pick-up Block • RV14
• When gain is lowered... The set does not play because of no focus operation. • When gain is highered... Operation noise is heard due to a scratch or a dust, then operation will be unstable.
[RF BOARD] – Conductor Side –
IC51
CNJ12
RV14
IC11
Procedure: 1. Set RV14 (RF board) to the standard position. 2. Check that there is not an abnormal amount of operation noise (white noise) from the 2-axis devise. If there is, turn RV14 slightly clockwise. [RF BOARD] – Conductor Side –
MIN side (low gain)
MAX side (high gain)
RV14 standard position
– 16 –
CDX-828 SECTION 7 DIAGRAMS BLOCK DIAGRAM – SERVO Section – DIGITAL SIGNAL PROCESSOR, CLV SERVO IC101
39 42 38 40
PD1 I-V AMP
32
46 47
FOCUS OK COMPARATOR
FOK
MIRR AMP
TTL IIL
DEFECT AMP
IIL
IIL TTL
OPTICAL PICK-UP (KSS-521A)
FOCUS ERROR AMP
FEO
1
DATA CLK XLT LOCK XRST
TTL IIL DATA REGISTER
RF AMP, FOCUS/TRACKING SERVO IC11 (1/2)
23
41 42
F
2
ASYO FOK
FEI
SENS1 C.OUT SENS2
FOCUS PHASE COMPENSATION
FEO
22 20 21 19 23 25 24 26
DATO 15 CLKO 17 XLTO 16
SEIN 13 CNIN 14
6
RFCK C2PO WDCK
RFCK
RFCK, GTOP, WFCK, C4M, XROF,
7
TRACKING PHASE COMPENSATION
TAO
LD
36
LD
LD AMP
(Page 19)
C
(Page 20)
D
(Page 19)
E
(Page 19)
F
(Page 19)
G
(Page 19)
H
(Page 19)
16K RAM ERROR CORRECTOR
DIGITAL CLV
GTOP 58 WFCK 74 EMPH 72
CPU INTERFACE
CLOCK GENERATOR
8 7 9 10 12 11 75 76 77
C4M
70
GTOP WFCK
C4M
61 100 89
SCLK 13 SBSO XROF
AUTOMATIC POWER CONTROL Q11
B
WDCK
C16M
TEI
(Page 19)
IC403 (2/2)
SUB-CODE PROCESSOR
26 27 28 29 64
47
A
1 2
LASER DIODE
PD
62 63 49
DATA, PCMD, BCK, LRCK, WDCK
PCMD BCK LRCK
52 54 50
FOCUS GAIN
TRACKING TEO 45 ERROR AMP
I-V AMP
E
40
EFM DEMODULATOR
DIGITAL PLL
ASYI
RV14 FE BIAS
ASYMMETRY CORRECTION
FOCUS OK AMP
F E
27
RF
PCMD BCKO LRCK
DATA
XTAI
44
INTERNAL BUS
C
33
XRST
B
RFI
PD2
I-V AMP
39
RFO
GFS
D
MON MDP MDS
A
RF SUMMING AMP
+
PD2 I-V AMP
LOCK XROF
DETECTOR
D/A INTERFACE
FILO CLTV PCO FILI
PD1
SERVO AUTO SEQUENCER
38
DIGITAL D.OUT 71 OUT
FILTER
SQSO SQCK SENS DATA CLOCK XLAT SCOR SBSO EXCK
7-1.
EDGE DETECT IC403 (1/2)
PD AMP
PD 37 SYSTEM CONTROLLER IC201 (1/3)
54 C.OUT 22 FOK 8 SENS2
FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC51
2 1
(TRACKING)
(FOCUS)
2-AXIS DEVICE
12 13
OUT+
SUBQ SCLK SENS CD.DATA CD.CLK CD.XLT SCOR GFS
52 51 23 67 65 66 63 24
OUT–
IN
OUT+ OUT–
FOCUS COIL DRIVE
IN
CHUCKING MOTOR DRIVE IC52 10
CH.R 5
SLED SERVO IC11 (2/2) 26 27
RESET
4
05
M
OUT+ SLED OUT– MOTOR DRIVE
IN
24
16
SLO
SLED AMP
SLP
14
4 5
OUT1
FIN RIN
CHUCKING MOTOR DRIVE
M101 (SPINDLE)
M
17 16
SPINDLE MOTOR DRIVE
IN
OUT2
1 7
M
M103 (CHUCKING)
SW12 (SAVE END DETECT) ON : When completion of the disc chucking operation.
LOAD1 7 OUT+ OUT–
SW11 (CHUCKING END DETECT)
19
ON : When completion of the disc chucking operation.
LOAD2 6
• SIGNAL PATH
SW1 (LIMIT) LIM.SW 9
– 17 –
DATA, CLOCK
SCOR
XRST 21 TRACKING COIL DRIVE
CH.F 4
M102 (SLED)
DATA CLOCK
: CD PLAY (ANALOG OUT) ON : When the optical pick-up is inner position.
: CD PLAY (DIGITAL OUT)
– 18 –
CDX-828
7-2.
BLOCK DIAGRAM – MAIN Section – OPTICAL TRANSCEIVER IC801 D/A CONVERTER IC601
D-RAM CONTROLLER IC401
SCOR
1, 2, 24, 25
DATA
47 48 46 50
4 23 3 22
XQOK
XWRE XSOE
45 44 49 59
LOW-PASS FILTER IC602 (1/2)
L MUTING Q603
PWM AOUTR
17
LOW-PASS FILTER IC602 (2/2)
R
16
XRAS 28 XCAS 34 XWE 29 XOE 35
D1 – D4
18
MUTING Q604
31, 30, 33, 32
2 XRST
60
SERIAL INPUT INTERFACE
INTERPOLATOR, ∆Σ MODULATOR
11
6
CLOCK OSC/ DIVIDER
XTI
XTO
PD
DFS
EMP 12
CPU INTERFACE
D-RAM IC402
4
5
X601 16.9344MHz
MUTING CONTROL SWITCH Q601, 602
CLOCK BUFFER IC603
XRAS XCAS XWE XOE
C16M
C
(Page 18)
I
(Page 22)
J
(Page 22)
45 47
43 A.MUTE
XRDE XWRE XSOE
44
D/A.RESET
41 42 28 26
ML
29 27
EMP
46
XQOK
25
ESPXLT SDTI
DATA, CLOCK
GRSCOR
F
A0 – A9
GRSRT
(Page 18)
VWA
ADDRESS MONITOR
1
BCK LRCK
AOUTL
DE-EMPHASIS CONTROL
CPU INTERFACE
RESET
7 9
DATA
A0 – A9
READ/WRITE BASE COUNTER
DATA LINKING CONTROL
XTAI
TIMING GENERATOR
8
D1 – D4
61
RFCK GTOP WFCK C4M XROI
25 – 22, 40 – 36, 27
7 8 3 5 6
BUFFER IC604
9 – 12, 14 – 18, 5
D-RAM INTERFACE RFCK GTOP WFCK C4M XROF
20
DATA 18 BCK 17 LRCK 19
D/A CONVERTER INTERFACE
SELECTOR
XRDE
H
SCOR
DSP INTERFACE
SDTI SCK XLT SDTO
G
BCKI LRCI WDCI DIN
GRST
(Page 18)
B
RFCK, GTOP, WFCK, C4M, XROF
11 9 12 13 4
CLOCK
(Page 18)
A
CN901 (1/2) ANALOG OUT
DATI
GSCR
(Page 18)
PCMD BCK LRCK WDCK DATA
WFCK
(Page 18)
D OUT
DIGITAL OUT
DATA, PCMD, BCK, LRCK, WDCK
IC801 DIGITAL OUT
(Page 18)
D
(Page 18)
E
SCLK
8
REQ BUSY
RESET
A/D.SW
76 74
75
56
7 6 5
4 56 REQ BUSY
79 78 77
CSO CSI CCLK
76 SCOR 77 WFCK
CSI CSO CCLK
SYSTEM CONTROLLER IC201 (2/3)
SW801 (ANALOG/DIGITAL SELECT)
ANALOG DIGITAL
D501
RESET
RST 28 CD TEXT DECODER IC501
SCLK
IC503
BU CHECK
BUCK 78
SBSO
EXTAL
20 – 27
XTAL
DATA0 – DATA7
62 63
30
29
CE
ADD0 – ADD14 11 – 18, 64 – 69, 74
WE
9 SSI
X501 10MHz
DO0 – DO7 S-RAM IC502
20 27 CE
11 – 13, 15 – 19
A0 – A14
• SIGNAL PATH
WE
10 – 3, 25, 24, 21, 23, 2, 26, 1
: CD PLAY (ANALOG OUT)
05
: CD PLAY (DIGITAL OUT)
– 19 –
– 20 –
CDX-828
7-3.
BLOCK DIAGRAM – BUS CONTROL /POWER SUPPLY Section –
SYSTEM CONTROLLER IC201 (3/3) RV201 MCK 38
LINEAR POSITION SENSOR RV202 ELEVATOR HEIGHT SENSOR
EHS 39
REFERENCE VOLTAGE SWITCH Q201
AVREF 37
SW201 MAGAZINE EJECT END DETECT
57 MGLK
+9V REGULATOR IC303
SERVO +9V
MICON +5V
D309
ELV.ON 69 D311 MICON +5V SW202 MAGAZINE IN/OUT DETECT
60 MAG.SW CD.ON 68 BU.CHK 61
BUS INTERFACE (FOR SONY BUS) IC302
ELEVATOR MOTOR DRIVE IC301 OUT1 1 OUT2 7
ELEVATOR MOTOR DRIVE
FIN RIN
SI 49
70 ELV.R 58 ELV.F
4 5
10
SO 50
9
SCK 48
11
BUS.ON 55
1 13
DATA
SO
+8V REGULATOR IC306
DAC +5V
+5V REGULATOR IC307
SERVO +5V
+5V REGULATOR IC305
B+ SWITCH Q305
D313
7 B.UP
6
SI
Q304
SCK
CLK
BUSON OUT
LOF
BUSON OUT
BUSON IN
BATTERY CHECK Q301, 302
4
LEVEL SHIFT D307
D308
5
12
DATA 4 CLK
2
EEPROM IC202
SDA SCL
6 RST 30
12 EE.DATA 11 EE.CLK
5 6
8
RESET
RESET SWITCH
RST
BUSON
2 RST
7
CN901 (2/2) CONTROL (FOR SONY BUS) RESET SIGNAL GENERATOR IC304
MICON +5V BU CHECK
J
(Page 20)
I
(Page 20)
D306 RESET
W.UP 62
EJECT 64
05
EXTAL
M
XTAL
M104 (ELEVATOR)
+8V LOW-PASS FILTER (IC602) B+
REGULATOR Q303
32
31
MICON +5V SW301 6
X201 8MHz
– 21 –
– 22 –
• Circuit Boards Location
JACK board MAIN board
DIGITAL OUT board RF board SW board
– 23 –
7-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. r : Through hole. • ¢ : internal component. • • b : Pattern from the side which enables seeing. Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. ¢ : internal component. • • C : panel designation.
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Note: Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
• U : B+ Line. • H : adjustment for repair. • Power voltage is dc 14.4V and fed with regulated dc power supply from CD changer controller. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : CD PLAY : Impossible to measure ∗ • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. J : CD PLAY (ANALOG OUT) c : CD PLAY (DIGITAL OUT)
– 24 –
CDX-828
7-5.
PRINTED WIRING BOARDS – RF/SW Boards –
• See page 23 for Circuit Boards Location.
• Semiconductor Location Ref. No.
Location
IC11 IC51 IC52
C-6 B-7 G-4
Q11
D-6
(Page 30)
– 25 –
– 26 –
CDX-828 7-6.
SCHEMATIC DIAGRAM – RF/SW Boards – • See page 39 for Waveforms.
• See page 45 for IC Block Diagrams.
(Page 33)
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
– 27 –
– 28 –
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
CDX-828
7-7.
PRINTED WIRING BOARD – MAIN Board (Component Side) – • See page 23 for Circuit Boards Location.
• Semiconductor Location (Component Side) Ref. No.
Location
D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D313 D314 D501 D502
E-3 E-3 E-3 E-3 E-3 E-7 G-4 G-4 E-2 F-4 G-5 F-4 D-3 F-3 F-7 H-5
IC101 IC201 IC202 IC301 IC302 IC304 IC306 IC307 IC401 IC402 IC403 IC501 IC502 IC503 IC601 IC602 IC603 IC604
B-7 E-7 D-8 G-3 E-4 G-4 C-3 A-5 D-5 E-5 A-6 G-7 G-6 G-6 B-5 B-5 B-5 B-6
Q201 Q301 Q302 Q304 Q601 Q602 Q603 Q604
E-9 G-5 G-4 C-3 F-6 F-5 D-4 D-4
(Page 42)
(Page 26)
– 29 –
– 30 –
7-8.
PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
CDX-828
• See page 23 for Circuit Boards Location.
• Semiconductor Location (Conductor Side) Ref. No.
– 31 –
– 32 –
Location
IC303 IC305
F-9 D-9
Q303 Q305
E-8 D-8
CDX-828 7-9.
SCHEMATIC DIAGRAM – MAIN Board (1/3) – • See page 39 for Waveforms.
• See page 46 for IC Block Diagrams.
(Page 28)
(Page 37)
– 33 –
– 34 –
CDX-828 7-10. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • See page 40 for Waveforms.
• See page 47 for IC Block Diagrams.
(Page 43)
(Page 38)
– 35 –
– 36 –
CDX-828 7-11. SCHEMATIC DIAGRAM – MAIN Board (3/3) –
• See page 40 for Waveforms.
• See page 47 for IC Block Diagrams.
(Page 34)
– 37 –
(Page 35)
– 38 –
• Waveforms – RF Board – – MAIN Board (1/3) – 1 IC11 #£ (RF O) 500 mV/DIV, 500 ns/DIV
6 IC101 ^™ (RFCK)
1 IC101 @¶ (MDP)
2.5 Vp-p
5.7 Vp-p
1.4 Vp-p
137 µs
7.6 µs 2 IC11 2 (FEI) 50 mV/DIV, 1 µs/DIV
2 IC101 #§ (V16M)
Approx. 110 mVp-p
7 IC101 &º (C4M)
6.8 Vp-p
236 ns
120 ns
3 IC11 $¶ (TEI) 200 mV/DIV, 500 µs/DIV
6.6 Vp-p
8 IC101 &¢ (WFCK)
3 IC101 $ª (WDCK)
Approx. 280 mVp-p
6.6 Vp-p
5.5 Vp-p
11.4 µs
137 µs
4 IC101 %º (LRCK)
9 IC101 *ª (XTAI)
6.6 Vp-p
22.7 µs
3.3 Vp-p
59.2 ns !º IC201 #¡ (EXTAL)
5 IC101 %¢ (BCKO)
6.6 Vp-p
472 ns
– 39 –
3.2 Vp-p
125 ns
– MAIN Board (2/3) –
– MAIN Board (3/3) –
!¡ IC603 4
!∞ IC401 !ª (LRCK)
4.7 Vp-p
@º IC401 7 (RFCK)
5.7 Vp-p
6.2 Vp-p
137 µs
22.7 µs
59.2 ns !™ IC601 4 (XTO)
6.4 Vp-p
6.2 Vp-p
472 ns
59.2 ns !£ IC601 7 (BCK)
6.6 Vp-p
236 ns @™ IC401 3, IC501&¶ (WFCK)
!¶ IC401 !£ (WDCI)
7.4 Vp-p
7.7 Vp-p
5.5 Vp-p
137 µs
11.4 µs
472 ns
!• IC401 !™ (LRCI)
!¢ IC601 9 (LRCK)
@£ IC403 1
6.6 Vp-p
6.6 Vp-p
7.4 Vp-p
22.7 µs
@¡ IC401 5 (C4M)
!§ IC401 !¶ (BCK)
22.7 µs
11.4 µs @¢ IC501 @ª (EXTAL)
!ª IC401 9 (BCKI)
6.6 Vp-p
472 ns
– 40 –
3.2 Vp-p
100 ns
CDX-828
7-12. PRINTED WIRING BOARDS – DIGITAL OUT/JACK Boards –
• See page 23 for Circuit Boards Location.
(Page 29)
– 41 –
– 42 –
CDX-828
7-13. SCHEMATIC DIAGRAM – DIGITAL OUT/JACK Boards –
(Page 36)
– 43 –
– 44 –
• IC Block Diagrams – RF Board –
RF M
RF O
35
34
33 32
PD 2 I-V AMP
PD 1 I-V AMP
PD AMP
LD AMP
VCC
31 30
29
28
27
CP
FOK
RFTC
36
CC2
LD
37
CC1
PD
38
CB
PD1
39
RF I
PD2
IC11 CXA1992BR
RF SUMMING AMP
FOCUS OK COMPARATOR
LASER POWER CONTROL
DEFECT AMP
TEI 47 ATSC WINDOW COMPARATOR
TZC 49
TZC COMPARATOR
LPC
MIRR PS1 – PS4
DFCTO
E-F BALANCE WINDOW COMPARATOR
TG1 – TG2
ATSC
IIL ↓ TTL
26 SENS2 25 SENS1 24 C. OUT
TTL ↓ IIL
23 22 21 20 19
IIC DATA REGISTER, INPUT SHIFT REGISTER, ADDRESS DECODER, SENSE SELECTOR, OUTPUT DECODER
FS1 – FS4
BALL
ATSC 48
TGFL
LDON
FOL VEE
LPFI 46
FOH
TGL BALH
IFB1 – IFB6 BAL1 – BAL4 TOG1 – TOG4
BAL1 – BAL4
EI 43 VEE 44 TEO 45
TGH
TRACKING GAIN WINDOW COMPARATOR
TGFL
VCC
18 VCC
VCC ISET
TM6
17 ISET
16 SL O 15 SL M
TM1 DFCT
TRACKING PHASE COMPENSATION TG1
+ –
TDFCT 50
TM5
VCC
14 SL P TM2
VEE
CENTER VOLTAGE GENERATOR
VC 51 FZC COMPARATOR
FZC 52
VCC TM7 TM4
VCC VEE
FOCUS PHASE COMPENSATION
FS1
CHARGE UP
+ –
FS2
FS4
DFCT
XRST DATA XLT CLK LOCK
FZC
E 42
E I-V AMP
TZC
F I-V AMP
TOG1 – TOG4
F 41
FOCUS BIAS WINDOW COMPARATOR
FOCUS ERROR AMP
LPCL
PEAK/BOTTOM HOLD
VEE
IIL ↓ TTL
CC1
FE 40 BIAS
MIRR COMPARATOR
DFCT1
PEAK/BOTTOM HOLD
TM1 – TM7
IFB1 – IFB6
FSET TM3
TG2
– 45 –
10
11
12
13
TA M
TA O
VEE 9
FSET
8
TG2
FGD
7
TGU
FDFCT
6
SRCH
FEI
5
FE M
4
FLB
3
FE O
2
FEO
VEE 1
IC52 BA6287F
OUT1 1
8 GND
VM 2
7 OUT2
DRIVER
DRIVER
TSD
VCC 3
6 VREF
CONTROL LOGIC
POWER SAVE FIN 4
5 RIN
– MAIN Board –
DOUT C4M FSTT XTSL
MNT0 MNT1 MNT3 XROF C2PO RFCK GFS XPCK XUGF GTOP VDD VSS TES4 BCK TES3 PCMD TES9
80 79 78 77 76 75 74 73 72
71 70 69 68
67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
TES6 VDD VSS EXCK SBSO SCOR
WFCK TES5 EMPH
IC101 CXD2530Q
50 LRCK 49 WDCK
ERROR CORRECTOR EFM DEMODULATOR
16K RAM
D/A INTERFACE
DIGITAL OUT
SUB CODE PROCESSOR
ASYMMETRY CORRECTOR
DIGITAL PLL
OSC
CLOCK GENERATOR TIMING LOGIC
SERVO AUTO SEQUENCER
CPU INTERFACE
DIGITAL CLV
XLTO CLKO SPOA SPOB SPOC SPOD XLON FOK VDD VSS MON MDP MDS LOCK PWMI
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
CLOK SEIN CNIN DATO
1 2 3 4 5 6
SQCK SQSO SENS DATA XLAT
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
VDD VSS LMUT RMUT TES2 CKOUT
NC VSS VDD NC TES7 NC VSS XVDD XTAI XTAO XVSS VSS NC TES8 NC VDD VSS NC NC XRST
– 46 –
48 47 46 45 44 43 42 41 40
ASYE ASYO ASYI BIAS RF AVDD CLTV AVSS FILI
39 38 37 36
FILO PCO VCTL V16M
35 34 33 32 31
VCKI VPCO1 VPCO2 TES1 TES0
IC202
AT24C16N-10SI-TR
IC301
BA6287F
OUT1 1 START STOP LOGIC
SERIAL EN CONTROL LOGIC
H.V. PUMP/TIMING
COMP
R/W
DATA RECOVERY
7 OUT2
7 TST
DRIVER
DATA WORD ADDR/COUNTER
DRIVER
TSD
LOAD INC
X DEC
A0 1 A1 2 A2 3
VM 2
8 VCC
LOAD DEVICE ADDRESS COMPARATOR
8 GND
6 SDL E2PROM
VCC 3
5 SDA
6 VREF
CONTROL LOGIC
GND 4 Y DEC
SERIAL MUX
POWER SAVE
DOUT/ACK LOGIC
DIN
FIN 4
5 RIN
DOUT
DATA OUT
DATA IN
RESET
12
11
10
9
8
RESET SWITCH
7
51 50 49 48 47 46 45 44 43
42
41
40 39 38 37 36 35 34 33
52 53 54 55 56 57 58 59
CPU I/F
32 31 30 29 28 27 26 25 24 23 22
ADDRESS MONITOR WRITE BASE COUNTER
DRAM I/F
VWA
READ BASE COUNTER
BUS RESET
D3 D0 D1 XWE XRAS A9 VDD A0 A1 A2 A3
SELECTOR TIMING GEN. GSCR 60 SCOR 61
DATA LINKING CONTROL
DSP I/F
DAC I/F
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15
16
17 18 19
BCKI VSS DATI LRCI WDCI TEST XTAO
XTAI
BCK DATA LRCK
NC 62 NC 63 NC 64 GRST XRST WFCK DIN C4M XROI RFCK GTOP
6 BUS DATA
5 VREF
4 BUS CLK
3 GND
2 BUS ON IN
BUS ON OUT
1
XWIH AM4 AM3 AM2 AM1 AM0 VDD XQOK
A4 A5 A6 A7 A8 XOE XCAS D2
CLK OUT
13
OSCE
LINK OFF
14
CXD2522Q
VSS
BUS ON
IC401
XEMP SDTO XSOE SCK SDTI XLT XRDE XWRE SPSL
BA8272F-E2
VCC
IC302
– 47 –
21 C176
DIGITAL OUT
20 DOUT
DATA INPUT BUFFER
27 WE
LEVEL SHIFT
BUFFER
I/O GATE COLUMN DECODER
I/O BUFFER
DIF0
DEM1
BVDD
DIF1
AOUTR
AOUTL
13
SERIAL INPUT INTERFACE
21 A10
BUFFER
14
A13 A8 A9 A11
22 OE
LEVEL SHIFT
19 18 17 16 15
CTF
SCF
∆Σ MODULATOR
8× INTERPOLATOR
CTF
SCF
∆Σ MODULATOR
8× INTERPOLATOR
CLOCK OSC/DIVIDER 20 CE 19 18 17 16 15
I/O8 I/O7 I/O6 I/O5 I/O4
GND 14
– 48 –
DE-EMPHASIS CONTROL 1
2
3
4
5
6
7
8
9
10
11
12
DEMO
I/O1 11 I/O2 12 I/O3 13
ROW DECODER
21 20
DFS
6 7 8 9 10
BUFFER
24 23 22
SMUTE
A4 A3 A2 A1 A0
LEVEL SHIFT
MEMORY MATRIX 512X512
26 25 24 23
AK4321-VF-E2
LRCK
1 2 3 4 5
A5 A4
IC601
KM62256DLG-7LT
28 VCC
A14 A12 A7 A6 A5
A8 A7 A6
VCOM
IC502
18 17 16 15 14
BICK
5 9 10 11 12 13
REFRESH ADDRESS COUNTER
PD
A9 A0 A1 A2 A3 VCC
PREADDRESS BUFFER DECODER
MODE CONTROL
XTI
4
BOARD BIAS GENERATOR
XTO
RAS
ROW DECODER
SDATA
CLOCK GENERATOR 1
4M BIT MEMORY CELL
AVDD
COLUMN SENSE AMP DECODER I/O GATE
23 CAS 22 OE
AVSS
CLOCK GENERATOR 2
DATA OUTPUT BUFFER
VREF
WRITE CLOCK GENERATOR
DZF
3
DVSS
WE
26 VSS 25 DQ4 24 DQ3
TTL
1 2
CKS
DQ1 DQ2
MSM514400D-60TS-K
DVDD
IC402
7-14.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC201 CXP84332-208Q (SYSTEM CONTROLLER) Pin No.
Pin Name
I/O
Function
1 to 3
—
O
Not used (open)
4
CH.F
O
Motor drive signal (load chucking direction) output to the chucking motor drive (IC52) “L” active *1
5
CH.R
O
Motor drive signal (save direction) output to the chucking motor drive (IC52) “L” active *1
6
LOAD2
I
Chucking end detect switch (SW11) input terminal “L”: When completion of the disc chucking operation
7
LOAD1
I
Save end detect switch (SW12) input terminal “L”: When completion of the disc chucking operation
8
SENS2
I
Internal status signal (sense signal) input from the CXA1992BR (IC11)
9
LIM.SW
I
Sled limit in detect switch (SW1) input terminal “L”: When the optical pick-up is inner position
10
EE.INIT
I
Initialize signal input for the EEPROM (IC202) “H”: format Fixed at “L” in this set
11
EE.CLK
O
Serial data transfer clock signal output to the EEPROM (IC202)
12
EE.DATA
I/O
Two-way data bus with the EEPROM (IC202)
13 to 19
—
O
Not used (open)
20
SINGLE
I
Setting terminal for the single disc/multiple discs mode “L”: single mode, “H”: multiple discs mode (fixed at “H”)
21
XRST
O
System reset signal output to the CXA1992BR (IC11), CXD2530Q (IC101) and CXD2522Q (IC401) “L”: reset
22
FOK
I
Focus OK signal input from the CXA1992BR (IC11) “L”: NG, “H”: OK
23
SENS
I
Internal status signal (sense signal) input from the CXD2530Q (IC101)
24
GFS
I
Guard frame sync signal input from the CXD2530Q (IC101) “L”: NG, “H”: OK
25
GRSRT
O
Reset signal output to the CXD2522Q (IC401) “L”: reset
26
XQOK
O
Subcode Q OK pulse signal output to the CXD2522Q (IC401) “L” active
27
SDTI
I
ESP status signal input from the CXD2522Q (IC401)
28
XSOE
O
ESP status read enable signal output to the CXD2522Q (IC401) “L” active
29
ESPXLT
O
ESP latch pulse signal output to the CXD2522Q (IC401) “L” active
30
RST
I
System reset signal input from the SONY bus interface (IC302) and reset signal generator (IC304) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (8 MHz)
32
XTAL
O
Main system clock output terminal (8 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open) Sub system clock input terminal Not used (fixed at “L”)
35
TEX
I
36
AVSS
—
37
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
38
MCK
I
Input of signal for the fine adjustment (linear position sensor adjustment; RV201) of elevator position (A/D input)
Ground terminal (for A/D converter)
39
EHS
I
Elevator height position detect input from the RV202 (elevator height sensor) (A/D input)
40
H.TEMP
I
High temperature sensor input terminal Not used (fixed at “L”)
41
XRDE
O
D-RAM read enable signal output to the CXD2522Q (IC401) “L” active
42
XWRE
O
D-RAM write enable signal output to the CXD2522Q (IC401) “L” active
43
A.MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
44
EMP
O
Emphasis mode output to the D/A converter (IC601) “H”: emphasis on
45
ML
O
Fast speed dubbing control signal output to the D/A converter (IC601) “L”: fast speed
46
GRSCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2522Q (IC401)
– 49 –
Pin No.
Pin Name
I/O
Function
47
D/A.RESET
O
Reset signal output to the D/A converter (IC601)
48
SCK
I
Serial data transfer clock signal input from the SONY bus interface (IC302)
“L”: reset
49
SI
I
Serial data input from the SONY bus interface (IC302)
50
SO
O
Serial data output to the SONY bus interface (IC302)
51
SCLK
O
Subcode Q data reading clock signal output to the CXD2530Q (IC101)
52
SUBQ
I
Subcode Q data input from the CXD2530Q (IC101)
53
—
O
Not used (open)
54
C.OUT
I
Track number count signal input from the CXA1992BR (IC11)
55
BUS.ON
I
Bus on/off control signal input from the SONY bus interface (IC302)
56
A/D.SW
I
Analog/digital select switch (SW801) input terminal
57
MGLK
I
Magazine eject operation completion detect switch (SW201) input
58
ELV.F
O
Motor drive signal (elevator up direction) output to the elevator motor drive (IC301) “L” active *2
59
—
O
Not used (open)
60
MAG.SW
I
Magazine in/out detect switch (SW202) input
61
BU.CHK
I
Battery detection signal input terminal
62
W.UP
I
Bus on or eject switch (SW301) input terminal
63
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
“H”: bus on
“L”: digital, “H”: analog “L”: eject completed
“L”: magazine detected
“H”: battery on “H”: bus on or eject switch pushing
64
EJECT
I
Eject switch (SW301) input terminal
65
CD.CLK
O
Serial data transfer clock signal output to the CXD2530Q (IC101) and CXD2522Q (IC401)
“H” active
66
CD.XLT
O
Serial data latch pulse signal output to the CXD2530Q (IC101)
67
CD.DATA
O
Serial data output to the CXD2530Q (IC101) and CXD2522Q (IC401)
68
CD.ON
O
D/A converter and servo section power supply on/off control signal output
69
ELV.ON
O
Mechanism deck section power supply on/off control signal output
70
ELV.R
O
Motor drive signal (elevator down direction) output to the elevator motor drive (IC301) “L” active *2
“H”: power on
“H”: power on
71
—
O
Not used (open)
72
VDD
—
Power supply terminal (+5V)
73
NC (VDD)
—
Connected to the power supply (+5V)
74
BUSY
I
75
RESET
O
Reset signal output to the CD text decoder (IC501)
76
REQ
I
Data request signal input from the CD text decoder (IC501)
77
CCCLK
O
Command clock signal output to the CD text decoder (IC501)
78
CSO
O
Command data output to the CD text decoder (IC501)
79
CSI
I
Command data input from the CD text decoder (IC501)
80
ADJ
I
Automatic/manual adjustment selection terminal “L”: manual adjustment mode, “H”: automatic adjustment mode (fixed at “H” in this set)
Busy monitor input from the CD text decoder (IC501)
*1 chucking motor (M103) control STOP
LOAD CHUCKING
SAVE
BRAKE
CH.F (pin 4)
“H”
“L”
“H”
“L”
CH.R (pin 5)
“H”
“H”
“L”
“L”
Mode Terminal
*2 elevator motor (M104) control Mode Terminal
STOP
ELEVATOR ELEVATOR UP DOWN
BRAKE
ELV.F (pin %•)
“H”
“L”
“H”
“L”
ELV.R (pin &º)
“H”
“H”
“L”
“L”
– 50 –
“L”: busy status
“L”: reset “L” active
• MAIN BOARD IC501 CXP83413-049Q (CD TEXT DECODER) Pin No.
Pin Name
I/O
Function
1, 2
NC
O
Not used (open)
3
NC
I
Not used (fixed at “L”)
4
REQ
O
Request signal output to the system controller (IC201) “L” active
5
CCLK
I
Serial data transfer clock signal input from the system controller (IC201)
6
CSI
I
Serial data input from the system controller (IC201)
7
CSO
O
Serial data output to the system controller (IC201)
8
SCLK
O
Clock signal output for subcode data reading to the CXD2530Q (IC101)
9
SSI
I
Subcode data input from the CXD2530Q (IC101)
10
NC
O
Not used (open)
11 to 18
ADD0 to ADD7
O
Address signal output to the S-RAM (IC502)
19
NC
I
Not used (fixed at “L”)
20 to 27 DATA0 to DATA7
I/O
Two-way data bus with the S-RAM (IC502)
I
System reset signal input from the system controller (IC201), SONY bus interface (IC302) and reset signal generator (IC304) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
EXTAL
I
System clock input terminal (10 MHz)
XTAL
O
System clock output terminal (10 MHz)
VSS
—
Ground terminal
32 to 55
NC
O
Not used (open)
56
BUSY
O
Busy signal output to the system controller (IC201) “L”: busy status
57 to 61
NC
O
Not used (open)
62
CE
O
Chip enable signal output to the S-RAM (IC502) “L” active
28
RST
29 30 31
63
WE
O
Data write enable signal output to the S-RAM (IC502) “L” active
64 to 69
ADD8 to ADD13
O
Address signal output to the S-RAM (IC502)
70
VDD
—
Power supply terminal (+5V)
71, 72
NC
O
Not used (open)
73
NC
I
Not used (fixed at “H”)
74
ADD14
O
Address signal output to the S-RAM (IC502)
75
NC
O
Not used (open)
76
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
77
WFCK
I
Write frame clock (7.35 kHz) signal input from the CXD2530Q (IC101)
78
BUCK
I
Backup power supply detection signal input terminal (used also to reset standby)
79, 80
NC
I
Not used (fixed at “L”)
– 51 –
SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Hardware (# mark) list and accessories and packing materials are given in the last of the electrical parts list.
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
27
(1)
#2
COVER SECTION
14 13
7
12
#11
#2
11 9
#2
13 10 MG-250C-137
12
IC305
#2
15 IC303
6
5
16
8
22
4
main flexible board
3
21 17
1
#13
18
#1
20 28 26 25
24 1
not supplied
23 19
2
19 Ref. No.
Part No.
Description
DAMPER (250) COVER (LOWER) JACK FLEXIBLE BOARD JACK BOARD DOOR (T) ASSY (EXCEPT US, Canadian)
18 18 * 19 20 20
X-3373-215-1 X-3375-357-1 3-013-658-01 X-3373-986-1 X-3375-360-1
ARM (FL) ASSY (US, Canadian) ARM (FLT) ASSY (EXCEPT US, Canadian) SHEET (FJ), PROTECTION ARM (FR) ASSY (US, Canadian) ARM (FRT) ASSY (EXCEPT US, Canadian)
X-3376-831-1 3-376-464-11 3-030-489-11 3-012-388-01 3-010-105-01
DOOR ASSY (US, Canadian) SCREW (+PTT 2.6X6), GROUND POINT PANEL, FRONT SCREW (M2X3) ESCUTCHEON (US, Canadian)
* 21 21 22 * 23 * 24
3-024-065-01 3-350-124-01 3-028-802-01 1-672-618-11 3-011-205-01
CUSHION (EJECT) (EXCEPT US, Canadian) CUSHION (EJECT) (US, Canadian) SPACER (MOUNT 30) DIGITAL OUT BOARD BRACKET (LIGHT)
9 10 10 11 12
3-022-006-01 3-010-106-01 3-022-007-01 3-022-012-01 3-010-103-01
ESCUTCHEON (T) (EXCEPT US, Canadian) BUTTON (EJ) (6) (US, Canadian) BUTTON (EJT) (6) (EXCEPT US, Canadian) HEAT SINK (T) SPRING (FL), TENSION
25 25 26 26 27
3-011-204-01 3-011-204-11 3-924-924-01 3-924-924-11 3-912-956-11
COVER (LIGHT) (US, Canadian) COVER (LIGHT) (EXCEPT US, Canadian) COVER (LIGHT) (US, Canadian) COVER (LIGHT) (EXCEPT US, Canadian) SCREW (2.6X6) (CU), +BVTT
13 * 14 * 15 * 16 17
3-010-101-01 3-010-096-11 A-3317-605-A 3-022-694-01 3-935-636-11
LEVER (FL) COVER (UPPER) MAIN BOARD, COMPLETE HOLDER (TR3) SCREW (FP)
28
3-024-067-01 CUSHION (T), BATTERY (EXCEPT US, Canadian) 3-911-215-02 SHEET (LEAD RETAINER) (US, Canadian) 8-759-054-12 IC PQ09RA1 8-759-231-53 IC TA7805S
Ref. No.
Part No.
Description
1 * 2 3 * 4 5
3-010-104-01 3-010-097-11 1-664-796-11 1-672-617-11 X-3376-459-1
5 6 7 8 * 9 * * * *
Remark
28 IC303 IC305
– 52 –
Remark
(2)
MECHANISM DECK SECTION-1 (MG-250C-137)
51
#3
#3
#3
52
53 54
Ref. No. 51 52
Part No.
Description
X-3375-497-1 CHASSIS (U) SUB ASSY 3-024-161-01 SPRING (SUT)
Remark
Ref. No. 53 54
– 53 –
Part No.
Description
4-965-759-01 WASHER, POLYETHYLENE 3-011-997-01 SPRING (STOPPER. LOWER)
Remark
(3)
MECHANISM DECK SECTION-2 (MG-250C-137)
#12
102
M104
103
101
Ref. No.
Part No.
Description
101 * 102
3-024-170-01 SPRING (SB), TENSION 3-024-172-01 BRACKET (EVM)
Remark
Ref. No. 103 M104
– 54 –
Part No.
Description
X-3375-498-4 CHASSIS (D) SUB ASSY A-3301-123-A ELJ MOTOR ASSY (ELEVATOR)
Remark
(4)
MECHANISM DECK SECTION-3 (MG-250C-137)
163
#8
162
#4
161
160
159
164 165
153
154
158 155
152
#8
157 166
156
#6 #6 M103
#6
151 #7 #6 Ref. No.
Part No.
Description
* 151 * 152 153 154 155
3-024-150-01 X-3375-445-1 3-010-270-01 3-321-813-01 3-017-139-01
156 157 158 159
3-010-255-01 3-573-936-00 X-3373-552-1 3-010-252-01
Remark
Ref. No.
Part No.
Description
RETAINER (CHM) BRACKET (CHM) ASSY COVER (CHM) WASHER, COTTER POLYETHYLENE GEAR (WORM LOAD A)
160 * 161 162 163 164
3-010-268-01 A-3290-194-F 3-010-254-01 3-010-253-01 3-701-438-11
SPRING (DH), TENSION CHASSIS (EVY) (MAIN) ASSY SHAFT (ROTARY PREVENTION C) GEAR (LOMINI) WASHER, 2.5
ARM (LSW) STOPPER, REEL GEAR (LOAD 1) ASSY ROLLER (CRE)
165 * 166 M103
1-664-627-11 MAIN FLEXIBLE BOARD A-3313-586-A RF BOARD, COMPLETE A-3301-123-A ELJ MOTOR ASSY (CHUCKING)
– 55 –
Remark
(5)
MECHANISM DECK SECTION-4 (MG-250C-137)
209 #10
208
not supplied
#7
207 206
#5
211 204
205
M101
212 not supplied #9 M102
#5
210 203
202 201
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Ref. No.
Part No.
Description
201 202 203 204 205
3-911-215-02 3-920-362-01 X-3373-229-1 3-010-258-01 3-573-936-00
SHEET (LEAD RETAINER) SCREW (ESCUTCHEON) BASE (SLED) ASSY GEAR (SLED MID) STOPPER, REEL
206 207
A-3291-958-A SHAFT (SLED) ASSY 3-010-263-01 DETENT (SHAFT THRUST)
Remark
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
* 208 * 209 210 ! 211 212
1-664-104-11 A-3301-077-A 1-664-626-11 8-820-010-05 3-010-262-01
SW BOARD BASE (OPT) (J) ASSY OP FLEXIBLE BOARD OPTICAL PICK-UP KSS-521A/J2RP DETENT (SLED)
M101 M102
– 56 –
A-3291-956-A MOTOR SUB ASSY, SPINDLE A-3291-955-A MOTOR SUB ASSY, SLED
Remark
DIGITAL OUT
SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable
Ref. No.
Part No.
*
1-672-618-11 DIGITAL OUT BOARD *****************
*
3-011-205-01 BRACKET (LIGHT)
JACK
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . • CAPACITORS uF: µF • COILS uH: µH
Description
Remark
Ref. No.
Part No.
MAIN
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board.
Description
Remark
< IC LINK > IC901
1-532-686-21 LINK, IC < SHORT >
< CAPACITOR > C801
1-162-927-11 CERAMIC CHIP
100PF
5%
R901 1-216-295-00 SHORT 0 ************************************************************
50V
< CONNECTOR > CN801
*
A-3317-605-A MAIN BOARD, COMPLETE ********************
*
3-022-694-01 HOLDER (TR3) 3-028-802-01 SPACER (MOUNT 30)
1-770-621-21 PIN, CONNECTOR 4P < IC >
IC801
< CAPACITOR >
8-749-923-53 IC TOTX193 (DIGITAL OUT) < RESISTOR >
R801
1-216-832-11 METAL CHIP
8.2K
5%
1/16W
< SWITCH > SW801 1-571-478-11 SWITCH, SLIDE (DIGITAL/ANALOG) ************************************************************ 1-672-617-11 JACK BOARD ***********
*
< CAPACITOR > C901 C902 C903 C904
1-163-263-11 1-163-038-00 1-163-009-11 1-163-009-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
330PF 0.1uF 0.001uF 0.001uF
5% 10% 10%
50V 25V 50V 50V
< CONNECTOR > CN901 CN901 CN902 CN903
1-779-077-11 PLUG, CONNECTOR (CONTROL, ANALOG OUT) (US, Canadian) 1-779-077-31 PLUG, CONNECTOR (CONTROL, ANALOG OUT) (EXCEPT US, Canadian) 1-770-621-21 PIN, CONNECTOR 4P 1-779-321-11 CONNECTOR, FPC 16P < FERRITE BEAD >
FB901 FB903
1-500-445-21 FERRITE 1-500-445-21 FERRITE
0uH 0uH
C101 C102 C103 C104 C105
1-164-182-11 1-164-004-11 1-163-035-00 1-163-011-11 1-163-001-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.1uF 0.047uF 0.0015uF 220PF
10% 10%
C106 C107 C108 C109 C110
1-135-214-21 1-163-021-11 1-163-038-00 1-163-038-00 1-163-009-11
TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
4.7uF 0.01uF 0.1uF 0.1uF 0.001uF
20% 10%
C112 C113 C114 C115 C201
1-163-038-00 1-163-038-00 1-163-038-00 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
25V 25V 25V 25V 25V
C202 C203 C204 C205 C301
1-163-038-00 1-163-038-00 1-163-038-00 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
25V 25V 25V 25V 25V
C302 C303 C304 C305 C306
1-163-038-00 1-163-038-00 1-163-009-11 1-163-029-11 1-109-982-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.001uF 10% 0.0047uF 50V 1uF 10%
25V 25V 50V
C307 C308 C309 C310 C311
1-109-982-11 1-163-038-00 1-125-701-11 1-104-953-11 1-109-982-11
CERAMIC CHIP CERAMIC CHIP DOUBLE LAYER ELECT CERAMIC CHIP
1uF 0.1uF 0.047F 47uF 1uF
10V 25V 5.5V 16V 10V
– 57 –
10% 10%
10%
10%
20% 10%
50V 25V 50V 50V 50V 20V 50V 25V 25V 50V
10V
MAIN Ref. No.
Part No.
Description
Remark
C312 C314 C315 C316 C317
1-115-650-11 1-104-953-11 1-163-038-00 1-115-466-00 1-115-651-11
ELECT ELECT CERAMIC CHIP ELECT ELECT
47uF 47uF 0.1uF 1000uF 100uF
20% 20%
C318 C319 C320 C321 C322
1-115-651-11 1-104-953-11 1-163-038-00 1-115-650-11 1-163-009-11
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
100uF 47uF 0.1uF 47uF 0.001uF
20% 20%
C401 C402 C403 C404 C405
1-163-038-00 1-163-038-00 1-109-982-11 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 1uF 0.1uF 0.1uF
C501 C502 C503 C504 C601
1-163-038-00 1-163-009-11 1-125-701-11 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP DOUBLE LAYER CERAMIC CHIP CERAMIC CHIP
0.1uF 0.001uF 0.047F 0.1uF 0.1uF
C603 C604 C605 C606 C608
1-109-982-11 1-163-038-00 1-163-038-00 1-115-650-11 1-163-003-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
1uF 0.1uF 0.1uF 47uF 330PF
10%
C609 C611 C612 C613 C614
1-163-003-11 1-163-243-11 1-163-243-11 1-163-038-00 1-115-650-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
330PF 47PF 47PF 0.1uF 47uF
10% 5% 5%
C615 C616 C617 C618 C619
1-115-650-11 1-163-038-00 1-104-913-11 1-163-009-11 1-163-009-11
ELECT CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP
47uF 0.1uF 10uF 0.001uF 0.001uF
20%
C621
1-163-038-00 CERAMIC CHIP
20% 20%
20% 10%
10%
10%
20% 10%
20%
20% 10% 10%
16V 16V 25V 16V 16V 16V 16V 25V 16V 50V 25V 25V 10V 25V 25V 25V 50V 5.5V 25V 25V 10V 25V 25V 16V 50V 50V 50V 50V 25V 16V 16V 25V 16V 50V 50V
Ref. No.
Part No.
Description
Remark
D501
8-719-988-61 DIODE 1SS355TE-17
D502
8-719-975-40 DIODE RB411D < FERRITE BEAD >
FB402 FB403 FB404 FB601 FB602
1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21 1-500-445-21
FERRITE FERRITE FERRITE FERRITE FERRITE
0uH 0uH 0uH 0uH 0uH
FB603 FB604 FB605
1-500-445-21 FERRITE 1-500-445-21 FERRITE 1-500-445-21 FERRITE
0uH 0uH 0uH
< IC > IC101 IC201 IC202 IC301 IC302
8-752-384-15 8-752-902-63 8-759-253-82 8-759-040-83 8-759-444-86
IC IC IC IC IC
CXD2530Q CXP84332-208Q AT24C16N-10SI-TR BA6287F BA8272F-E2
IC303 IC304 IC305 IC306 IC307
8-759-054-12 8-759-443-41 8-759-231-53 8-759-284-66 8-759-284-63
IC IC IC IC IC
PQ09RA1 RH5VL40AA-T1C TA7805S TA78M08F (TE16L) TA78M05F (TE16L)
IC401 IC402 IC403 IC501 IC502
8-752-374-09 8-759-576-67 8-759-242-76 8-752-904-83 8-759-497-29
IC IC IC IC IC
CXD2522Q MSM514400D-60TS-K TC7W08F CXP83413-049Q KM62256DLG-7LT
IC503 IC601 IC602 IC603 IC604
8-759-243-19 8-759-455-21 8-759-064-92 8-759-243-19 8-759-243-19
IC IC IC IC IC
TC7SU04F AK4321-VF-E2 NJM5532M-D TC7SU04F TC7SU04F
< COIL > 0.1uF
25V L601
1-410-381-11 INDUCTOR CHIP 10uH
< CONNECTOR > < TRANSISTOR > CN101 CN301 * CN302
1-770-351-11 CONNECTOR, FPC 26P 1-774-679-21 CONNECTOR, FPC 16P 1-580-055-21 PIN, CONNECTOR (SMD) 2P < DIODE >
D301 D302 D303 D304 D305
8-719-975-40 8-719-017-94 8-719-017-94 8-719-975-40 8-719-975-40
DIODE DIODE DIODE DIODE DIODE
RB411D MA8180 MA8180 RB411D RB411D
D306 D307 D308 D309 D310
8-719-801-78 8-719-422-64 8-719-988-61 8-719-210-33 8-719-988-61
DIODE DIODE DIODE DIODE DIODE
1SS184 MA8062-M 1SS355TE-17 EC10DS2 1SS355TE-17
D311 D312 D313 D314
8-719-038-48 8-719-422-62 8-719-210-33 8-719-975-40
DIODE DIODE DIODE DIODE
1SS319 (TE85R) MA8062-L-TX EC10DS2 RB411D
Q201 Q301 Q302 Q303 Q304
8-729-020-67 8-729-027-31 8-729-230-49 8-729-016-11 8-729-901-00
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
XN1A312-TX DTA124EKA-T146 2SC2712-YG 2SD1507M DTC124EK
Q305 Q601 Q602 Q603 Q604
8-729-016-83 8-729-901-00 8-729-027-23 8-729-015-39 8-729-015-39
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SB1446 DTC124EK DTA114EKA-T146 DTC323TK DTC323TK
< RESISTOR > R101 R102 R103 R104 R105
1-216-105-00 1-216-121-00 1-216-113-00 1-216-061-00 1-216-061-00
R106
1-216-073-00 METAL CHIP
– 58 –
RES, CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP
220K 1M 470K 3.3K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
10K
5%
1/10W
MAIN Ref. No.
Part No.
Description
R107 R108 R109 R110
1-216-121-00 1-216-073-00 1-216-097-00 1-216-073-00
RES, CHIP METAL CHIP RES, CHIP METAL CHIP
1M 10K 100K 10K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
Remark
R111 R114 R201 R202 R203
1-216-049-11 1-216-049-11 1-216-089-00 1-216-089-00 1-216-089-00
RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP
1K 1K 47K 47K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R204 R205 R206 R207 R208
1-216-089-00 1-216-081-00 1-216-089-00 1-216-049-11 1-216-089-00
RES, CHIP METAL CHIP RES, CHIP RES, CHIP RES, CHIP
47K 22K 47K 1K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R210 R211 R212 R213 R214
1-216-089-00 1-216-089-00 1-216-089-00 1-216-089-00 1-216-065-00
RES, CHIP RES, CHIP RES, CHIP RES, CHIP RES, CHIP
47K 47K 47K 47K 4.7K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R215 R219 R301 R302 R303
1-216-065-00 1-216-049-11 1-216-089-00 1-216-089-00 1-216-689-11
RES, CHIP RES, CHIP RES, CHIP RES, CHIP METAL CHIP
4.7K 1K 47K 47K 39K
5% 5% 5% 5% 0.5%
1/10W 1/10W 1/10W 1/10W 1/10W
R304 R305 R306 R307 R308
1-216-089-00 1-216-057-00 1-216-077-00 1-216-049-11 1-216-073-00
RES, CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP
47K 2.2K 15K 1K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R309 R311 R312 R313 R314
1-216-089-00 1-216-089-00 1-216-073-00 1-216-295-00 1-216-295-00
RES, CHIP RES, CHIP METAL CHIP SHORT SHORT
47K 47K 10K 0 0
5% 5% 5%
1/10W 1/10W 1/10W
R316 R401 R402 R403 R501
1-216-073-00 1-216-033-00 1-216-105-00 1-216-033-00 1-216-089-00
METAL CHIP METAL CHIP RES, CHIP METAL CHIP RES, CHIP
10K 220 220K 220 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R502 R503 R504 R505 R601
1-216-049-11 1-216-049-11 1-216-073-00 1-216-049-11 1-216-041-00
RES, CHIP RES, CHIP METAL CHIP RES, CHIP METAL CHIP
1K 1K 10K 1K 470
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R602 R603 R604 R605 R606
1-216-033-00 1-216-081-00 1-216-081-00 1-216-049-11 1-216-049-11
METAL CHIP METAL CHIP METAL CHIP RES, CHIP RES, CHIP
220 22K 22K 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R607 R608 R609 R611 R612
1-216-685-11 1-216-685-11 1-216-073-00 1-216-089-00 1-216-089-00
METAL CHIP METAL CHIP METAL CHIP RES, CHIP RES, CHIP
27K 27K 10K 47K 47K
0.5% 0.5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R613 R614 R615 R616
1-216-069-00 1-216-025-00 1-216-025-00 1-216-121-00
METAL CHIP RES, CHIP RES, CHIP RES, CHIP
6.8K 100 100 1M
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
Ref. No.
Part No.
Description
RF Remark
< VARIABLE RESISTOR > RV201 RV202
1-223-834-11 RES, ADJ, CARBON 47K 1-225-412-11 RES, VAR, SLIDE 10K (ELEVATOR HEIGHT SENSOR) < SWITCH >
SW201 1-762-108-31 SWITCH, PUSH (1 KEY) (MAGAZINE EJECT END DETECT) SW202 1-762-108-31 SWITCH, PUSH (1 KEY) (MAGAZINE IN/OUT DETECT) SW301 1-571-532-21 SWITCH, TACTIL (6) < VIBRATOR > X201 1-767-261-21 VIBRATOR, CERAMIC (8MHz) X501 1-767-510-11 VIBRATOR, CERAMIC (10MHz) X601 1-767-366-41 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************ A-3313-586-A RF BOARD, COMPLETE ******************
*
< CAPACITOR > C10 C12 C13 C14 C15
1-163-009-11 1-113-500-11 1-163-038-00 1-165-176-11 1-162-957-11
CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 100uF 0.1uF 0.047uF 220PF
10% 20%
C16 C17 C18 C19 C21
1-107-826-11 1-164-227-11 1-111-253-11 1-163-038-00 1-162-966-11
CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.022uF 100uF 0.1uF 0.0022uF
10% 10% 20% 10%
16V 25V 6.3V 25V 50V
C22 C23 C24 C25 C26
1-107-823-11 1-113-682-11 1-107-826-11 1-107-826-11 1-163-021-11
CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.47uF 33uF 0.1uF 0.1uF 0.01uF
10% 20% 10% 10% 10%
16V 10V 16V 16V 50V
C27 C28 C29 C30 C31
1-164-677-11 1-164-245-11 1-165-176-11 1-162-970-11 1-113-987-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP
0.033uF 0.015uF 0.047uF 0.01uF 4.7uF
10% 10% 10% 10% 20%
16V 25V 16V 25V 25V
C32 C33 C34 C35 C36
1-164-677-11 1-162-915-11 1-162-970-11 1-104-700-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.033uF 10PF 0.01uF 0.027uF 0.01uF
10% 0.5PF 10% 10% 10%
16V 50V 25V 16V 25V
C37 C38 C39 C40 C41
1-109-982-11 1-104-913-11 1-163-038-00 1-109-982-11 1-164-227-11
CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
1uF 10uF 0.1uF 1uF 0.022uF
10% 20% 10% 10%
10V 16V 25V 10V 25V
C42 C43 C51 C52 C53
1-164-227-11 1-164-227-11 1-163-019-00 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 10% 0.022uF 10% 0.0068uF 10% 0.1uF 0.1uF
25V 25V 50V 25V 25V
– 59 –
10% 5%
50V 10V 25V 16V 50V
RF Ref. No.
SW Part No.
Description
C54 C55 C56 C57 C58
1-163-038-00 1-163-023-00 1-163-038-00 1-163-038-00 1-163-038-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
Remark
C59 C60
1-163-038-00 CERAMIC CHIP 0.1uF 1-104-914-11 TANTALUM CHIP 22uF
0.1uF 0.015uF 0.1uF 0.1uF 0.1uF
5%
20%
Ref. No.
25V 50V 25V 25V 25V 25V 16V
Part No.
Description
Remark
R50 R51 R52
1-216-841-11 METAL CHIP 1-216-073-00 METAL CHIP 1-216-093-00 RES, CHIP
47K 10K 68K
5% 5% 5%
1/16W 1/10W 1/10W
R53 R54 R55 R56 R57
1-216-073-00 1-216-073-00 1-216-073-00 1-216-093-00 1-216-081-00
METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP
10K 10K 10K 68K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R58 R59 R60 R61 R62
1-216-093-00 1-216-073-00 1-216-073-00 1-216-073-00 1-216-085-00
RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
68K 10K 10K 10K 33K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R63 R64 R65
1-216-073-00 METAL CHIP 1-216-073-00 METAL CHIP 1-216-073-00 METAL CHIP
10K 10K 10K
5% 5% 5%
1/10W 1/10W 1/10W
< CONNECTOR > CNJ11 CNJ12 * CNP11 * CNP51 CNP52
1-778-776-21 1-778-777-21 1-580-055-21 1-580-055-21 1-580-055-21
CONNECTOR, FPC 17P CONNECTOR, FPC 26P PIN, CONNECTOR (SMD) 2P PIN, CONNECTOR (SMD) 2P PIN, CONNECTOR (SMD) 2P
* CNP53
1-580-055-21 PIN, CONNECTOR (SMD) 2P < IC >
< VARIABLE RESISTOR > IC11 IC51 IC52
8-752-082-14 IC CXA1992BR 8-759-071-79 IC BA6297AFP 8-759-040-83 IC BA6287F
RV14
1-238-091-11 RES, ADJ, CERMET
22K
< SWITCH > < TRANSISTOR > SW11
Q11
1-762-946-12 SWITCH, PUSH (1 KEY) (CHUCKING END DETECT) SW12 1-762-946-12 SWITCH, PUSH (1 KEY) (SAVE END DETECT) ************************************************************
8-729-141-48 TRANSISTOR 2SB624-BV345 < RESISTOR >
R11 R12 R13 R14 R16
1-218-348-11 1-216-839-11 1-216-839-11 1-218-348-11 1-216-857-11
RES, CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP
110K 33K 33K 110K 1M
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R17 R18 R22 R25 R26
1-216-837-11 1-216-841-11 1-216-857-11 1-216-851-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 47K 1M 330K 100K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R27 R28 R30 R31 R32
1-216-295-00 1-216-295-00 1-216-829-11 1-216-829-11 1-216-837-11
SHORT SHORT METAL CHIP METAL CHIP METAL CHIP
0 0 4.7K 4.7K 22K
5% 5% 5%
1/16W 1/16W 1/16W
R33 R34 R35 R36 R37
1-216-158-00 1-216-855-11 1-216-835-11 1-216-836-11 1-216-851-11
RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22 680K 15K 18K 330K
5% 5% 5% 5% 5%
1/8W 1/16W 1/16W 1/16W 1/16W
R38 R39 R40 R41 R42
1-216-837-11 1-216-847-11 1-218-273-11 1-218-296-11 1-202-930-11
METAL CHIP METAL CHIP RES, CHIP RES, CHIP RES, CHIP
22K 150K 510K 75K 750K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R43 R44 R45 R46 R47
1-216-849-11 1-216-846-11 1-216-837-11 1-216-847-11 1-216-834-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
220K 120K 22K 150K 12K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R48 R49
1-216-845-11 METAL CHIP 1-216-093-00 RES, CHIP
100K 68K
5% 5%
1/16W 1/10W
1-664-104-11 SW BOARD *********
*
< SWITCH > SW1 1-572-688-11 SWITCH, PUSH (1 KEY) (LIMIT) ************************************************************ MISCELLANEOUS ************** 3 165 210 ! 211 M101
1-664-796-11 1-664-627-11 1-664-626-11 8-820-010-05 A-3291-956-A
JACK FLEXIBLE BOARD MAIN FLEXIBLE BOARD OP FLEXIBLE BOARD OPTICAL PICK-UP KSS-521A/J2RP MOTOR SUB ASSY, SPINDLE
M102 A-3291-955-A MOTOR SUB ASSY, SLED M103 A-3301-123-A ELJ MOTOR ASSY (CHUKING) M104 A-3301-123-A ELJ MOTOR ASSY (ELEVATOR) ************************************************************ ************** HARDWARE LIST ************** #1 #2 #3 #4 #5
7-627-852-07 7-685-792-09 7-685-781-09 7-624-104-04 7-627-554-07
SCREW, PRECISION +P 1.7X2.5 SCREW +PTT 2.6X6 (S) SCREW +PTT 2X4 (S) STOP RING 2.0, TYPE-E SCREW, PRECISION +P 2X2.2
#6 #7 #8 #9 #10
7-628-253-00 7-627-553-27 7-624-102-04 7-627-850-28 7-627-000-00
SCREW +PS 2X4 SCREW, PRECISION +P 2X2.5 STOP RING 1.5, TYPE-E SCREW, PRECISION +P 1.4X3 SCREW, PRECISION +P 1.7X2.2 TYPE3
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
– 60 –
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
Remark
Ref. No.
#11 7-685-780-01 SCREW +PTT 2X3 (S) (EXCEPT US, Canadian) #11 7-685-851-04 SCREW +BVTT 2X4 (S) (US, Canadian) #12 7-685-780-09 SCREW +PTT 2X3 (S) #13 7-685-853-04 SCREW +BVTT 2X6 (S) ************************************************************ ACCESSORIES & PACKING MATERIALS ******************************** 3-865-014-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH, CHINESE) (US, Canadian) 3-865-037-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH, CHINESE) (E) 3-865-037-21 MANUAL, INSTRUCTION (ENGLISH, SPANISH, SWEDISH, PORTUGUESE) (AEP, UK) 3-865-037-31 MANUAL, INSTRUCTION (FRENCH, GERMAN, DUTCH, ITALIAN) (AEP, UK) 3-865-037-41 MANUAL, INSTRUCTION (GERMAN, RUSSIAN) (German) A-3291-950-C MAGAZINE (250) ASSY ************************************************************ PARTS FOR INSTALLATION AND CONNECTIONS ************************************** 501 * 502 503 504 504
3-011-778-01 X-3369-824-1 1-590-874-11 1-590-519-21
BRACKET (705) SCREW ASSY CORD, CONNECTION (RCA PIN CORD 5.5m) CORD (WITH CONNECTOR) (BUS CABLE 5.5m) (US, Canadian) 1-590-519-81 CORD (WITH CONNECTOR) (BUS CABLE 5.5m) (EXCEPT US, Canadian)
501
502
BRACKET (705) ×2
503
RCA PIN CORD 5.5 m ×1
+PSW 4 × 10 ×4
TAPPING SCREW (DIA. 5 × 20) × 4
504
BUS CABLE 5.5 m ×1
– 61 –
Part No.
Description
Remark
CDX-828
Sony Corporation 9-926-402-11
Personal & Mobile Communication Company
– 62 –
98L0578-1 Printed in Japan © 1998. 12 Published by Quality Assurance Dept.
