Transcript
HCD-NE3 SERVICE MANUAL
US Model Canadian Model AEP Model UK Model E Model Australian Model
Ver 1.0 2004.03
• HCD-NE3 is the amplifier, CD player, tape deck and tuner section in CMT-NE3.
CD Section
TAPE Section
Model Name Using Similar Mechanism
NEW
Base Unit Name
BU-K7BD80B
Optical Pick-up Name
KSM-213EDP/C2NP
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
CMAL5Z220A
SPECIFICATIONS AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (US model)
With 6 ohm loads, both channels driven, from 120-10,000 Hz; rated 13 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output.
Inputs MD (phono jacks): Outputs PHONES:
SPEAKER:
Sensitivity 450 mV, impedance 47 kilohms Accepts headphones with an impedance of 8 ohms or more Accepts impedance of 6 to 16 ohms.
CD player section Main unit
Laser
Amplifier section North American model: Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD) European model: DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 15 + 15W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 25 + 25 W Other models: The following measured at AC 230 V or AC 120 V, 50/ 60 Hz DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD)
Frequency response Wavelength
Semiconductor laser (λ=780 nm) Emission duration: continuous 20 Hz – 20 kHz 780 – 790 nm
Tape deck section Recording system Frequency response
4-track 2-channel, stereo 50 – 13,000 Hz (±3 dB), using Sony TYPE I cassettes
Tuner section
General
FM stereo, FM/AM superheterodyne tuner
Power requirements US, Canadian and Mexican models: 120 V AC, 60 Hz AEP and UK models: 230 V AC, 50/60 Hz Australian model: 230 – 240 V AC, 50/60 Hz Argentina and Korean models: 220 V AC, 60 Hz Taiwanese model: 120 V AC, 50/60 Hz Saudi Arabian model: 120 – 127/220 V AC, 50/ 60 Hz Other models: 110 – 120 V or 220 – 240 V AC, 50/60 Hz Adjustable with voltage selector
FM tuner section Tuning range Antenna Antenna terminals Intermediate frequency
87.5 – 108.0 MHz FM lead antenna 75 ohms unbalanced 10.7 MHz
AM tuner section US, Canadian, Mexican and Argentina models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,710 kHz (with the tuning interval set at 9 kHz) AEP and UK models: 531 – 1,602 kHz (with the tuning interval set at 9 kHz) Other models: 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,602 kHz (with the tuning interval set at 9 kHz) Antenna AM loop antenna, external antenna terminal Intermediate frequency 450 kHz
Power consumption
45 W
Dimensions (w/h/d)
Approx. 164 × 230.5 × 263 mm incl. projecting parts and controls
Mass
Approx. 3.7 kg
Supplied accessories
Remote Commander (1) R6 (size AA) batteries (2) AM loop antenna (1) FM lead antenna (1)
Design and specifications are subject to change without notice.
COMPACT DISC DECK RECEIVER 9-877-693-01
Sony Corporation
2004C05-1 © 2004.03
Home Audio Company Published by Sony Engineering Corporation
HCD-NE3
Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
The following caution label is located inside the unit.
CLASS 1 LASER PRODUCT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT
This appliance is classified as a CLASS 1 LASER product.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
This label is located on the rear exterior.
UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size)
To Exposed Metal Parts on Set
0.15 µF
1.5 k Ω
AC voltmeter (0.75 V)
Earth Ground
: LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 ˚C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 ˚C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
2
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
HCD-NE3
TABLE OF CONTENTS 1.
SERVICING NOTES ................................................ 4
2.
GENERAL Location of Controls ....................................................... 6
3.
DISASSEMBLY
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8.
Disassembly Flow ........................................................... Rear Cabinet .................................................................... Top Panel Assy ................................................................ Front Panel Assy ............................................................. Base Unit (BU-K7BD80B) ............................................. Mechanical Deck ............................................................. MAIN Board ................................................................... AMP Board .....................................................................
4.
TEST MODE .............................................................. 12
5.
ELECTRICAL CHECK .......................................... 14
6.
DIAGRAMS
6-1. Block Diagram – CD SERVO Section – ....................... 6-2. Block Diagram – MAIN Section – ................................ 6-3. Note for Printed Wiring Boards and Schematic Diagrams ................................................ 6-4. Printed Wiring Board – BD Board – ............................. 6-5. Schematic Diagram – BD Board – ................................ 6-6. Printed Wiring Boards – MAIN Section – .................... 6-7. Schematic Diagram – MAIN Section – ......................... 6-8. Printed Wiring Boards – AMP Section – ....................... 6-9. Schematic Diagram – AMP Section – ........................... 6-10. Printed Wiring Boards – PANEL Section – .................. 6-11. Schematic Diagram – PANEL Section – ....................... 6-12. Printed Wiring Board – POWER Board – ..................... 6-13. Schematic Diagram – POWER Board – ........................
8 8 9 9 10 10 11 11
15 16 17 18 19 20 21 22 23 24 25 26 27
7.
EXPLODED VIEWS
7-1. 7-2. 7-3. 7-4.
Panel Section ................................................................... Front Panel Assy-1 .......................................................... Front Panel Assy-2 .......................................................... Top Panel Assy ................................................................
8.
ELECTRICAL PARTS LIST ............................... 36
32 33 34 35
3
HCD-NE3 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
• MODEL IDENTIFICATION – Rear Cabinet –
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Power Voltage Indication
MODEL
Power Voltage Incdication
US, Canadian, Mexican and models
AC: 120 V 60 Hz 45 W
AEP and UK models
AC: 230 V - 50/60 Hz 45 W
Australian model
AC: 230 – 240 - 50/60 Hz 45 W
Argentina and Korean models
AC: 220 V - 60 Hz 45 W
Taiwan model
AC: 120 V 50/60 Hz 45 W
Saudi Arabia model
AC: 120 – 127/220 V 50/60 Hz 45 W
Other models
AC: 110 – 120/220 – 240 V 50/60 Hz 45 W
NOTE ON LEADING THE WIRE (FLAT TYPE) • In order to separate wire (flat type) from no shield portion of TC wire, stick filament tapes, as shown in a figure. TC wire (no shield portion)
main board
filament tape wire (flat type)
4
HCD-NE3
SERVICE POSITION – BD board –
BD board
– TCM block –
TCM block
– AMP board –
AMP board
5
HCD-NE3 SECTION 2 GENERAL • LOCATION OF CONTROLS
Main unit BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
?/1 (power) 1 .m/M> (skip back/ skip forward,rewind/fast forward) 4 x (stop) 3 z RECPAUSE/START qh CD/NX(play/pause) ql TAPE/N(play) w; Z PUSHOPEN/CLOSE (CD open/close) 6 Z PUSHOPEN (tape open/close) qd
P–Z
A–O
PHONES jack qk PLAY MODE qj Remote sensor 2 TUNER/BAND qs TUNING +/− 4 TUNING MODE qj VOLUME qa
BASS/TREBLE 8 Cassette compartment qf CD SYNCHRO qg DISPLAY 0 Displaywindow 5 DSGX 9
1 2 34 5
6
8 9 0 qa qs
w; ql qk qj
qd qf
qh qg
6
This section is extracted from instruction manual.
HCD-NE3
Setting the clock
Remote control BUTTON DESCRIPTIONS
ALPHABETICAL ORDER A–O
?/1 (power) 1 m/M (rewind/fast forward) 7 ./> (go back/go forward) qf x (stop) 8 X (pause) 8 N (play) 8 +/− (tuning) qf
P– Z
CD qh CLEAR qd CLOCK/TIMER SELECT 2 CLOCK/TIMERS ET 3 DISPLAY ql ENTER 9 EQ qs FM MODE 4 FUNCTION 6
PLAY MODE qk REPEAT 4 SLEEP w; TAPE qg TUNER/BAND 5 TUNER MEMORY qj TUNING MODE qk VOLUME +/− 0
Use buttons on the remote for the operation.
1 2 3 4 5 6
Press ?/1 to turn on the system. Press CLOCK/TIMER SET. Press ./> repeatedly to set the hour. Press ENTER. Press ./> repeatedly to set the minute. Press ENTER.
The clock starts working.
To adjust the clock
1 Press CLOCK/TIMER SET. 2 Press ./> until “CLOCK” appears, then press ENTER.
3 Do the same procedures as step 3 to 6
CMT-NE3
above. Note
w;
ql qk qj qh qg qf
1
The clock is not displayed in Power Saving Mode.
2 3 4 5 6 7 8
qd qs
9
* 0
* Button does not function with this model.
7
HCD-NE3 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW SET
3-2. REAR CABINET (Page 8)
3-3. TOP PANEL ASSY (Page 9)
3-4. FRONT PANEL ASSY (Page 9)
3-5. BASE UNIT (BU-K7BD80B) (Page 10)
3-6. MECHANICAL DECK (Page 10)
3-7. MAIN BOARD (Page 11)
3-8. AMP BOARD (Page 11)
Note: Follow the disassembly procedure in the numerical order given.
3-2.
REAR CABINET
1 four screws (BVTP3 × 8)
4 five screws (BVTP3 × 10) 3 two screws (BVTP3 × 10)
7 rear cabinet
6 two screws (BVTP3 × 10)
5 two screws (BVTP3 × 10)
2 four screws (BVTP3 × 8)
8
HCD-NE3
3-3.
TOP PANEL ASSY 6 top panel assy
5 connector (S820)
3
4 wire (flat type) (17 core) (CN305)
2 claw
1 claw
3-4.
FRONT PANEL ASSY 2 wire (flat type) (8 core) (CN303) q; wire (flat type) (11 core) 3 connector (CN309) 5 connector (CN301) 4 connector (CN501)
1 wire (flat type) (19 core) (CN302) qa screw (2.6 × 10) qs harness
9 8
7 qd flont panel assy
6 two screws (BVTP3 × 10)
9
HCD-NE3
3-5.
BASE UNIT (BU-K7BD80B)
6 base unit (BU-K7BD80B)
4 two screws (2.6 × 10) 5 two screws (2.6 × 10)
3 wire (flat type) (17core) (CN201)
2 CD cover
1 three screws (BVTP2.6 × 8)
3-6.
MECHANICAL DECK 2 screw (BVTT2.6 × 6)
1 three screws (2.6 × 10)
3 shield (TC)
4 mechanical deck
10
HCD-NE3
3-7.
MAIN BOARD
5 main board
1 connector (CNB308)
3 connector (CNB307)
4 two screws (BVTP3 × 10)
6 tuner (FM/AM)
2 connector (CN902)
3-8.
AMP BOARD
4 AMP board
3 two screws (BVTP3 × 10)
1 connector (CNB308) 2 connector (CNB307)
11
HCD-NE3 SECTION 4 TEST MODE COLD RESET *
The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press the I/1 button to turn the power on. 2. While pressing the x button, press the I/1 button and turn the [VOLUME] knob in the counter-clock wise. 3. The message “RESET” is displayed and the set is reset.
PANEL TEST All segments of liquid crystal display are tested, and the version and released date of the micro computer are displayed. Procedure: 1. Press the I/1 button to turn the power on. 2. While pressing the [DISPLAY] button, press the I/1 button and turn the [VOLUME] knob in the counter-clock wise. Then all segments of liquid crystal display are turned on. 3. Press the [DSGX] button, the version and released date of the micro computer are displayed. example of display:
The third and 4th digit from the left indicates: (Error status display) The third and 4th digit from the left indicates which error status is indicated. Display
Not focused (TOC read without a disc)
0 2
GFS NG (TOC read with a disc chucked)
0 3
Start operation time-over
0 4
Defocused continuously (Defocused during TOC reading)
0 5
Q code not entered for specified time
0 6
Tracking not turned ON
0 7
Blank disc (Blank disc TOC read)
*
1209 V100
Status
0 1
The 5th and 6th digit from the left indicates: (Error step display) The 5th and 6th digit from the left indicates which processing when a trouble occurred Display
Contents
0 1
SHIP in progress
0 2
Power OFF in progress
released date of micro computer (In this case, released of December 9)
0 3
Power ON in progress
0 4
Initialize in progress
4. Press the [BASS/TREBLE] button, the model name and destination are displayed. example of display:
0 5
Oscillation stopping
0 6
From oscillation stop, oscillation starting
0 7
Stopping
0 8
Stop operation is under way
Version of micro computer (In this case, version 100)
N3 NA
5.
0 9
Start operation in progress
destination (In this case, North-American model)
0 A
TOC read in progress
0 B
Search operation is under way
model name (In this case, HCD-NE3)
0 C
Playback operation is under way
0 D
Pause operation is under way
0 E
Playback manual search operation is under way
0 F
Pause manual search operation is under way
To exit from this mode, perform the “COLD RESET”.
CD ERROR CODE DISPLAY MODE • When this mode is entered, optical pick-up error code is displayed with the 8-character format on the liquid crystal display. Procedure: 1. Press the I/1 button to turn the power ON. 2. Press the CD N X button to select “CD”. 3. While pressing the [DISPLAY] button, press the [PLAY/MODE/ TUNING MODE] and turn the [VOLUME] knob in the counterclockwise. 4. When this mode is activated, CD error code is displayed on the liquid crystal display. 5. Press the TUNING + M > and TUNING – . m buttons, error history No. is changed. The first digit from the left indicates: The first digit from the left indicates which mode the error history is. “D” is displayed on the liquid crystal display. The second digit from the left indicates: (Error history No. display) The second digit from the left indicates which order the error history is. “0” indicates the latest error history, and each time the number increases by one, the error history goes back to one-previous error.
12
The 7th and 8th digit from the left indicates: The 7th and 8th digit from the left indicates which operation in progress when a trouble occurred. (Step of each processing of the 5th and 6th digits is indicated)
5 REPEAT LIMIT CANCEL MODE • Number of repeat for CD playback is 5 times when the repeat mode is “REPEAT”. This mode is used to enables CD to repeat playback for limitless times. Procedure: 1. Press the I/1 button to turn the power ON. 2. Press the CD N X button to select “CD”. 3. While pressing the x button, press the [PLAY MODE/TUNING MODE] and turn the [VOLUME] knob in the counterclockwise. 4. The message “NO LIMIT” is displayed on the liquid crystal display momentarily, CD repeat 5 limit is cancelled.
HCD-NE3
TUNER STEP CHANGE-OVER *
Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. Procedure: 1. Set the FUNCTION to AM, and press the I/1 button to turn the power off. 2. While depressing the TUNING + M > button, press the I/1 button. 3. The message “9K STEP” or “10K STEP” is displayed on the liquid crystal display, and thus the channel step is changed over.
13
HCD-NE3 SECTION 5 ELECTRICAL CHECK Note: 1. CD Block is basically constructed to operate without adjustment. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Check the focus bias check when optical block is replaced. FOCUS BIAS CHECK oscilloscope (DC range) BD board TP012 (RFACO) TP013 (VC)
+ –
Procedure : 1. Connect the oscilloscope to TP012 (RFACO) and TP013 (VC) on the BD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the CD N X button. 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished. • RF signal reference waveform (eye pattern) VOLT/DIV: 0.2 V (with the 10: 1 probe in use.) TIME/DIV: 500 ns
1.1
0.2 Vp-p
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.
Checking Location: – BD BOARD (Conductor Side) –
TP012 (RFACO)
14
TP013 (VC)
HCD-NE3 SECTION 6 DIAGRAMS BLOCK DIAGRAM – CD SERVO Section – 110
CD DSP IC101 (1/2)
XTAO
B 26 C 27 D I-V AMP
28
RF SUMMING AMP
B C
32
33
EQ_ IN
RFAC VCA
EQ
RFACO
38
39 42
FOCUS ERROR AMP
D
AC_ SUM
FEO
43
23
RFACI
ASYMMETRY CORRECTOR
XTAI XTACN
EFM DEMODULATOR
DIGITAL PLL
ASYI ASYO
AOUT1 INTERNAL BUS
FILO PCO CLTV FILI
25
A
CLOCK GENERATOR
48 50 47 49 105
D +3.3V
A
XTSL
XPCK
DETECTOR
86
C4M
FILTER
32K RAM ERROR CORRECTOR
D/A CONVERTER
AOUT2
D/A DIGITAL INTERFACE
72
X171 16.9344MHz
73 88
CD 76 81
R-CH
SELECTOR TO SERVO AUTO SEQUENCER
DIGITAL CLV PROCESSOR
6
93
95 98 97 100 108 91 92 89 90
103 104 106 64
59 62 61
LRCKI BCKI PCMDI
WFCK XUGF GFS EMPH
OPTICAL PICK-UP BLOCK (KSM-213EDP)
CPU INTERFACE SBSO EXCK SQSO SQCK
21
SCOR
TEO
SENS
TRACKING ERROR AMP
E
MDP
18
DATA CLOK XLAT
19 E
SUBCODE PROCESSOR
F
XRST
F
LRCK BCK PCMD
6-1.
58 56 57
LASER DIODE PD
APC LD AMP
35
6 8 9
7
27 CD SCOR
LD
CD SENS
LD
34
CD DATA CD CLK CD XLT
PD
AUTOMATIC POWER CONTROL Q10
CD XTXCN 3 MOTOR/COIL DRIVE IC251
M101 (SPINDLE)
M
16 15
CH4OUTF CH4OUTR
MOTOR DRIVE
CH4IN
24
27
OPOUT
OPIN+
2
CH3FIN
MOTOR CH3OUTR DRIVE 18
CH3RIN
SYSTEM CONTROLLER IC801 (1/2)
23
A/D CONVERTER
22
9 10
2-AXIS DEVICE (FOCUS) (TRACKING)
14 13
CH1OUTF CH1OUTR
CH1FIN COIL DRIVE
CH1RIN
4
11
5
12 13 14
12 11
CH2OUTF CH2OUTR
CH2FIN COIL DRIVE
CH2RIN
SFDR SRDR TFDR TRDR FFDR FRDR
FOCUS/ TRACKING/SLED SERVO DSP
MIRR, DFCT, FOK DETECTOR
FOK MIRR DFCT
COUT SERVO INTERFACE
SCLK
3 1 2
112 101
SERVO AUTO SEQUENCER
6 7
MUTE
• R-ch is omitted due to same as L-ch. • SIGNAL PATH
CD XRST
CH3OUTF
SSTP
M
17
FOCUS/TRACKING/SLED PWM GENERATOR
M102 (SLED)
TEI FEI
20 22 CD DSP IC101 (2/2)
TO CPU INTERFACE
20
: CD PLAY
5
7 S101 (LIMIT)
15
15
A
(Page 16)
HCD-NE3
6-2.
BLOCK DIAGRAM – MAIN Section – J303
L
19 AUX-L
MD R
A
(Page 15)
R-CH
CD
OUT-L 18
POWER AMP IC501
21 CD-L
J301 PHONES
R-CH FM/AM TUNER PACK FM 75Ω COAXIAL
FM ANT
TU-LCH
23 TU-L
TU-DI AM ANT TU-DO TU-CL ANT GND TU-CE TUNED STEREO MUTE
AM
: TUNER
R-CH
ANT GND TU-RCH ANTENNA
• R-ch is omitted due to same as L-ch. • SIGNAL PATH
+
DO DI CLK CE TUNED STEREO TU-MUTING
INPUT SELECT, ELECTRICAL VOLUME IC302
+ –
L
+ –
R
: CD PLAY
J302 SPEAKER IMPEDANCE USE 6 – 16Ω
: TAPE PLAY : REC : AUX IN
REC-O-L 28
2 TA-L
CONT 13
L-CH
R-CH HRPE301 (REC/PB/ERASE)
DC DETECT Q342, 343
REC BIAS SWITCH Q346 – 348
R-CH
B +10V
MAIN POWER TRANSFORMER T902
D307 D920, 921
+
ERASE REC/PB SWITCH Q326 – 332
BIAS OSC T301
BIAS OSC Q344, 345
AC DETECT Q333, 338
AMP B+
RECT D918, 919
AMP B–
RECT D916, 917
DO DI CLK CE TU-MUTING TUNED STEREO
TO POWER AMP
12
16
15
98 99
18
F DATA
XT2
XT1
CF2
CF1
AMP STBY
I POWER MONITOR
SYSTEM CONTROLLER IC801 (2/2)
97
39
LED DRIVE Q808
LED DRIVE Q806
+3.3V REGULATOR Q317 +7V REGULATOR IC306
M +7V
+3.3V REGULATOR Q339
D810
D806 (STANDBY)
VOLTAGE DETECT IC803
I POWER DOWN 23
LCD COM0 – 3
29 RMC
RESET 11 22 VOL ENCODER PWR ON 1
S801 – 813 (FRONT PANEL KEYS)
16
(E, E51, EA, SP) SUB POWER TRANSFORMER T901
SYS +3.1V SYS +3.2V
ROTARY ENCODER RV801
RECT D913, 914
D809
S820 (CD LID OPEN/CLOSE DETECT)
VOLUME
(EXCEPT E, E51, EA, SP)
+10V REGULATOR IC305
VM +10V
4 CD OPEN D701 – 703 (LCD BACK LIGHT)
B+ SWITCH Q319, 320
CD ON 2
SEG1 – 33
FL801 FLUORESCENT INDICATOR TUBE
REMOTE CONTROL RECEIVER IC802
D +3.3V
SYS +3.3V
25, 26
79 – 56, 53 – 45
24 TA-SW 91 TA PLAY SW 92 TA END SW
AMP MUTE
13
96 TA SOL
PACK REC PLAY SW FWD SW
28
ST/BY
(DECK-A)
PLUNGER DRIVE Q802, 803
94 95
TA REC/PLAY TA BIAS
SOL 9V
93 TA MOTOR
32 30 34 35 33 36 37
BACK LIGHT ON
(CAPSTAN/REEL)
CAPSTAN/REEL MOTOR DRIVE Q804, 805
83 – 86
M
MOTOR 9V
X802 10MHz
TU DO TU DI TU CLK TU CE TU MUTE TU TUNED TU STEREO
TAPE MECHANISM DECK BLOCK
X801 32.768kHz
KEY0, KEY1
16
+3.9V REGULATOR Q312 – 314
RECT D907 – 910 D922
D923, 924
RY901 VOLTAGE SELECTOR S901 (AC IN)
(EXCEPT E, E51, EA, SP)
RESET SWITCH Q801 MAIN POWER RELAY DRIVE Q311, 315
HCD-NE3
6-3.
• Circuit Boards Location
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. f • : internal component. : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
• Indication of transistor.
C Q
These are omitted.
B E
Q B
C
E These are omitted.
Q B
C
E These are omitted.
Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f • : internal component. • 2 : nonflammable resistor. • 5 : fusible resistor. • C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
MAIN board
BD board AMP board
CONTROL board
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce por tant le numéro spécifié.
• A : B+ Line. • B : B– Line. • Voltages and waveforms are dc with respect to ground under no-signal conditions. – CD Board – no mark : CD PLAY – Other Sections – no mark : TUNER ( ) : CD PLAY 〈〈 〉〉 : TAPE PLAY { } : REC • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : TUNER J : CD PLAY E : TAPE PLAY j : REC f : AUX IN • Abbreviation AR : Argentina model AUS : Australian model CND : Canadian model E51 : Chiliean and Peruvian models EA : Saudi Arabia model KR : Korean model MX : Mexican model SP : Singapore model TW : Taiwan model
HP board
BACK LIGHT board POWER board TUNER unit
17
17
HCD-NE3 • See page 17 for Circuit Boards Location.
PRINTED WIRING BOARD – BD Board –
:Uses unleaded solder.
BD BOARD
R121
C131
JW114
C132
C111 R113
28
TP013 (VC)
15
16
JW111 JW110
JR106 JW108
CN101
JW120
JW117
IC101 56
1
JW119
1
JW123
C161
57
M101 (SPINDLE)
C15
2
M
112
C160
JW107
R151
JW109
JW116
C141
R143
R141
C195
C143
OPTICAL PICK-UP BLOCK (KSM-213EDP)
JW112
C114 JR107
C204 R142
R202
JR111
E
C115
C142
C11
C113 R114
29
C124
Q10
C112
C133 R132
C10
R10
JR105
R111 R112
C125
TP012 (RFACO)
R133
C17 R11
R131
JR108
JW115
C122
C117
R13
C14
JR109
C16
R12
JW113
C116
C123
C18
JW118
R251 JW106
C162 C251
R161
C171
JW105
R171 C164
X101 C183
C172
R181
R173
C194
C184
C182
JR104
R182
R252
C212
7
C259
JW125
C186 JW126 JR110
C201
R162
R407
C202
JW134 JR101 R410
JW103
21
8
R406
C252
14
15
R408 C170 M102 (SLED)
C213
CN201
A
MAIN BOARD CN305
(Page 20)
18
18
R411
12
JW101
M
C203
JW127
R412
C258
C257
R204 R201
22
JW133
C163
S101 (LIMIT)
IC251
JW132
C211
C210
28
JR102
JW131 R409 JW128
JW104 1
JR103
85
C181
C151
C174
84
C185
R172
JW124
6-4.
1-861-620-
JW102
(12)
HCD-NE3 • See page 28 for IC Block Diagrams.
SCHEMATIC DIAGRAM – BD Board –
• See page 28 for Waveforms.
CN201 17P XTACN C201 220 10V
JR110 0
C174 0.1
C161 0.1
C151 220 10V
C171
MGND(7V)
22p
X101 16.9344MHz R172 1M R171 470
M+7V
JR103 0
PCMDI
LRCKI
VSS
LRCK
BCK
PCMD
VDD
EMPH
EMPHI
IOVDD2
XTAI
XTAO
XVDD
VREFL
AOUT1
AVDD1
AVSS1
AVSS2
0.1 C163
C212 22p
VREFR
100 R406
C211 220p
AOUT2
100 R407
IOVDD0
100
LMUT
JR104 0
100
C210 0.1
AVDD2
C143 0.1 RMUT 100
R151 0
BCKI
XTSL
DDCR
IOVSS0
AVSS5
R202 0
XTACN
DDVRSEN
SQSO
DDVROUT
SQCK
AVDD5
SBSO
PCO
EXCK
FILI
XRST
FILO
SYSM
CLTV
DATA
AVSS3
VSS
VCTL
XLAT
VPCO
CLOK
ASYO
R141 4.7k
R142 1k
C141 0.1 R143 3.3k
C125 0.1 C142 1500p C117 0.1
R132 10k
R133 180k
C133 0.01
TP46 IOP1 C132
VDD
CD DSP
ASYI
SENS
IC101 CXD3058AR
BIAS R131
SCLK
AVDD3
ATSK
RFACI
1M
C131
TP012 WFCK
RFACO
XUGF
AVSS4
XPCK
RFC PD
GFS
PD
C2PO
LD
0.47
C17 220 10V
R13 1 TP45 IOP2
100p
C124 330p
RFACO
R121
15k
C123
0.1
R12 100k
EQ_IN
SCOR
C164 0.1
VDD
AC_SUM
C4M
PDSENS
C122 0.1
R11 0
AUTOMATIC POWER CONTROL
D
C
B
A
VC
FEI
AVDD4 F
FFDR
TRDR
TFDR
SRDR
SFDR
IOVSS1
SSTP
MDP
LOCK
VSS
MIRR
FOK
DFCT
COUT
Q10 2SB1690K C18 1000p
JR109 0
RFDCO
WDCK
R10 3.3
C16 1
JPO001
JR102 0
JR105 0
CN101 16P
C15 0.1
TP27
JR111 0
FFDR
D
C
B
A
TRDR
TFDR
SRDR
SFDR
C195 0.1
C11 10 TP016 C251 6800p
0.1
R252 22k
C14 0.1 JPO003
T-
T+
F+
FRDR
FFDR
TRDR
TFDR
F-
C258 0.1
C114 470p JR107 0
R113 1k
R111 1k
R114 15k
R112 15k C113 3300p
C111 3300p
C10 10
C116 220 10V
VCC E
E
TP014
D
TP17
D
A
TP18
A
B
TP19
B
C
TP20
C
F
TP015 JR106 0
R251 10k
VC
TOP1
E
C115 0.1
JPO002
C259
SSTP
VC
TP013
C160 0.1
D A B JR108 F
0
C F AGND
TP28
LD
LD
TP21
AGND
VR
PD
TP22
PD
PD
F+
TP23
F+
F+
T+
TP24
T+
T+
T-
TP25
T-
T-
F-
TP26
F-
F-
C112 470p
MOTOR/COIL DRIVE
IC251 BA5947FM S101 (LIMIT)
C252 0.1
M101
JPO004
SRDR
(SPINDLE) SFDR
TP43 TP44
R408
M+7V
R173 0
C183 220 10V
TEI
SCOR
C185 470p
C184 220 10V
C172
SENS
TP42
C186 470p
C194 0.1
R182
TP41
SCOR MGND(7V)
R162 47k
CLK
SENS
R409
TP40
R412 100
XLT
100
CLK
TP39
TEST
DATA
XLT
R410
(Page 21)
DOUT
XRST
TP38
E
TP37
DATA
F
XRST
C162 0.1
R204
TES1
DVDD
AVSS0
TP36
C203 220 10V
C202 0.1
22p
E
DVDD
C213
XVSS
DGND
IOVSS2
ROUT
TP35
AVDD0
TP34
DGND
AVDD
IOVDD1
ROUT
TP32
R201
FRDR
AGND
FRDR
LOUT
TP30
C181 0.1
100
TP33
AGND
AVDD
C182 0.1
100
R181
LOUT
R161
27p
DOUT
100
TP31
DOUT
FEO
TP29
AGND
TEO
XTACN
R411
6-5.
M102
C170 220 16V
(SLED)
C257 0.1
JR101 0
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
19
19
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-NE3
8
F
AMP BOARD CN502
:Uses unleaded solder.
9
10
11
12
13
14
R320 R303
R301
C207
C204
C104
C107
D302
C331
JW313
C329
JW347 C101
C209
JW349
C109 JW344
R100
R114
R113
C211
C354
R218
R319
C312 C102
R102
C202
C206
R107 R202
R217
R117
R219
R119
C330
D303
B Q348
(Page 24)
E
C328
C355
C362
R368
C356
JW363
JW322 8
JW366
R362
R332
C323
Q344
JW365
+
E
E
JW384
Q339
JW382
JW369
JW370
R360
Q345
JW371
D304
JW381
C358
I
CONTROL BOARD CNB302
R367
JW364
JW362
JW319
C357 JW367
C335
E
JW351
6
JW361
CNB301
1
R366 R353
JW360 CNB307
1
1
6
E
Q347
JW358
H
5
T301 3 2
C361
JW357
R
4
JW323
C346
C353
R115
R365
C320
C219
7
R364
JW377
L201
R-CH
R201
C360
CN302
R318
JW380
E Q319
–
JW350
C201
E
JW352
JW341
JW353 JW378
JW318
E
JW356
JW379
JW316
C121
R208
L-CH
Q326
C314
Q346
JW354
Q320 R317
JW311
R348
JW315
HRPE301 (REC/PB/ERASE) 1
JW359
Q317
E
C309
JW310
E
7
C112
C212 R226
JW355 C221
G
Q342
E
JW321
C333
Q343
–
J302 SPEAKER IMPEDANCE USE 8 – 16Ω
R214 R215
C217
C351
E
E
C332 C352
C236
C115
C119
F
C216 C117
JW340
JW338
JW314 L101
L
1
R111
R358 C136
E
D CN301 D
C111
R359 JW339
JW309 +
C110
R213
C116 R225
Q332
Q331
G
Q328
R112
R212
R118
R216
R125
C215
1
E
D305
D306 R220
R116
R132 C135
JW343
JW320
R228
R124
R221
R126
D321
R109
R211 R120 R121
S
Q327
R209
C210
JW337
D322
R143
JW335
HP BOARD CNB501
(Page 22)
28
C114
G
Q330
JW345 E JW346 JW348
R122
JW333
R371
R231
C118
R370
3
R131 C218
C
R372
D
R128
CNB308
R203
1
15
JW336
R243 C133
S
D
C113
C213
JW334
1
C106 R103
R222
C233
FB302
R232
JW332
9
C103
G
Q329
R108
C235 C234
JW331
R136
JW329
C126
C203
S
IC302
R123 JW327
R137 R
R105
R223
JW328
J303 MD
C132
R106
14
JW324
JW325
FB317
C127
C208
R304
C232
C322
JW326
C227
R224
C308
C370
L
C214
CN305
JW304
(CHASSIS)
JW301
C305
R236
C
JW342
C226
R206 R205
C108
C302
R207
CN303
R101
R302
R200
R204
D318
R305
R104
C313 C315
C310
JW308
C301
C316
R237
R363
C345
POWER BOARD CN902
JW368
E
R361
(Page 26)
J
D317
11
C336
(11)
IC306
Q333
Q313
Q312
R321 Q315
JW372
E
R322
E
JW373
E
R325
R315 D310
D308 Q311
N
20
20
D301
Q338 E
R336 R350
11 1-861-724-
E
M
R351
E
Q314
L
D307
E
JW375
R327 3
JW376
IC305 REG BOARD
1
R324
3
C350
R326
R323
C306
C307 1
3
CN306
C326
1
1-861-729-
3
CN307
R349
C324
1
K
16
(Page 24)
FB301
B
15
CONTROL BOARD CNB303
R352
C318
JW383
C319
JW307
MAIN BOARD
7
(Page 22)
C134
M-11 L-10 L-10 L-9 K-13 F-8 G-7 F-7 C-14 C-13 B-14 B-13 B-13 B-14 B-15 K-12 K-14 I-9 F-10 E-9 H-13 I-13 E-12 G-12 G-12
D
BD BOARD CN201
(Page 18)
R373
Q311 Q312 Q313 Q314 Q315 Q317 Q319 Q320 Q326 Q327 Q328 Q329 Q330 Q331 Q332 Q333 Q338 Q339 Q342 Q343 Q344 Q345 Q346 Q347 Q348
C-12 K-6 K-7
6
JW302
IC302 IC305 IC306
5
A A
C321
K-14 B-13 G-8 I-9 C-11 C-10 K-13 M-10 L-10 K-12 B-10 E-5 D-5
4
JW312
D301 D302 D303 D304 D305 D306 D307 D308 D310 D317 D318 D321 D322
3
CN309
Location
2
JW120
Ref. No.
1
C311
• Semiconductor Location
PRINTED WIRING BOARDS – MAIN Section – • See page 17 for Circuit Boards Location.
C317
6-6.
(11)
ERASE
HCD-NE3 • See page 28 for IC Block Diagram.
SCHEMATIC DIAGRAM – MAIN Section –
• See page 28 for Waveforms.
J302 4P R225
22k
C232
4.7
50V
R125
22k
C132
4.7
50V
C119 0.01
L SPEAKER
10k
IMPEDANCE
470p
220p
J303 2P
4.7k
R136
C127
C126
R137
FB317
USE 8-16
C117
0.0012
R126
22k
C136
10
50V
TU LCH
C217
0.0012
R226
22k
C236
10
50V
TU RCH
C219 0.01
R
C121 0.1
LP221
C211 0.0033
C116 470p
(CHASSIS)
R221
C213 0.22 50V
15k
15k
R108
CN301 7P
R208
HRPE301
10k
SP OUT(R) GND L101
C214 0.47 50V R222 68k
SP OUT(L)
(Page 23)
CN309 3P C115 4.7 50V
C133 0.047
CNB308 9P
C235 10 50V
R143 8.2k
R R124 15k
R209 2.2k
JW120 0.1
L201
R223 2.2k
C114 0.47 50V R122 68k
R121
C113 0.22 50V
R120
10k R220
R123 2.2k
2.2k
2.2k
1.8k
6.8k R118
R119
R219
R117 R218
R116
6.8k
8.2k
8.2k R216
1.8k
2.2k
2.2k
C221 0.1
R217
C370 0.1
(CHASSIS)
C212 0.0047
R214 560 R212 33k
R211 2.2k
R111 2.2k
C210 180p
R109 2.2k
C216 470p
R213 470
C111 0.0033 R113 470
R112 33k
R236 10k
(REC/PB/ERASE)
R114 560
470p
R115 3.3k
C110 180p
C109
R215 3.3k
C209
470p
470p C227
220p C226
4.7k
L
C112 0.0047
R MD
R237
AGND
C215 4.7 50V
L R132 1k R224 15k
AMP-MUTE
C135 10 50V
R232 1k
AMP-STBY
(Page 23)
PROTECT BASS-R
OUT-R
BASS-L
OUT-L
AUX-L
AUX-R
CD-L
TU-L
CD-R
TU-R
RECO-R
NF-R
RECO-L
NF-L
-B L-CH
C233 0.047
INPUT SELECT,
R243 8.2k
GND +B R370 10k R371 10k
VEE
IC302 BD3881FV
1800p
39k R202
C202
39k R102
1800p
R105
390k
R106 5.6k R104 47 C104 100 10V
R107 150k
C352 2200 35V
C309 1000 16V
D318 1SS133T-77 R352 470
REG07-IN
C333 220 50V
+10V REGULATOR
R206 5.6k
C204 100 10V
C302 470 6.3V
R207 150k
D305 MTZJ-T-77 -4.3C
IC305 TA7810S O
R303 10k
R204 47
C306 0.1
REG07-GND
R302 15k
C208 0.0033
R301 47k
CN306 3P
CNB307 6P
REG07-OUT
R372 82k
C206 0.022
I G
C118 0.033
C218 0.033
O
R128 1.2k C134 0.0022
R131 1.2k
R359 1.5k C108 0.0033
C207
C106 0.022
C107 2.2 50V
R203 470
R228 1.2k
2.2
R205 390k
C103 100p
C203 100p
R103 470
IC306 BA07T +7V REGULATOR
R231 1.2k
50V
ERASE
C234 0.0022
VDD
CONT
VOLUME
TRE-R
GND
TRE-L
VOLI-R
PBO-L
VOLI-L
PB0-R
NF-R
TA-R
NF-L
R-CH
TA-L
ELECTRICAL
C102
C305 470 6.3V
C301 10p
C313 100 16V
I G
C323 2200 25V
C351 100 25V
D306 MTZJ-T-77 -4.3C
CN307 3P
R358 56k
C307 0.1
Q326-332 REC/PB SWITCH
Q330 2SK2158 -T2B
CN302 19P TU RCH
C101 68p
C201 68p
R101 12k
R201 12k
R100 180
R200 180
Q329 2SK2158 -T2B
R320 4.7k
Q332 KRA303 -RTK
S
DC DETECT
TU LCH
+B
SUB +B
R373 10k
PROTECT RELAY ON AC-DET
TU-RCH TU GND
GND
14V
D302 1SS133T -77
C312 220p
TU 10V TU 10V
D308 1SS133T-77
M+7V M+7V
Q326 KTA1504
S
TA 10V
(Page 27)
CNB301 8P
TU-LCH
Q311,315
TA GND
Q311 KTA1271Y-AT
MAIN POWER
JW323 10UH
TA GND
MGND(7V)
Q314 KTA1271Y-AT
SCOR C310 0.1
RELAY DRIVE
TA BIAS
F DATA
C317
100p
SCOR SENS SENS
C311
AC DETECT
R323 1k
REGULATOR
C326 0.0022
C316
100p
C315
100p
XLT DATA XRST
+3.9V
AMP-STBY
CLK
100p DATA
R324 2.2k
Q312-314 R315 1k
Q333,338
100p XLT
R351 10k
P-CONT
100p
C319
D310 MTZJ-T-77 -4.3C
R321 100k
A-MUTE
C318
CLOK
R336 4.7k
REC/PB
XRST
R325 100k
DVDD C322 0.001
AMP-MUTE
DGND
Q338 KRC402-RTK
I POWER MONITOR AC-DET
ROUT
AC-DET
Q333 KRC402-RTK
3.3V(MAIN)
LOUT Q312 KTC3203Y
GND C336 22 50V
GND
(Page 19)
AGND
Q315 KRC402-RTK
C324 220 16V
R350 10k
Q313 KTC3203Y
C321 0.001
C346 2200 16V
R322 1.5k
AVDD FB301
DOUT
3.9V(SUB)
AGND XTACN
D301 1SS133T-77
XTACN C329 1000 6.3V
Q346 2SD1387-34 -TP
Q347 KTA1266-GR -AT
R349 56k
R327 10k
CN305 17P
C308 0.1
CN303 8P
R326 100k
SCOR SCOR
BIAS OSC
1k XLT
DATA XRST XRST XTACN
0.01
470
16V
D304 MTZJ-T-77 -3.9B
XTACN CD ON
TU 10V
TA 10V
REG07-GND
Q345 2SC2001TP-LK
FB302
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
21
(Page 25)
CD ON
C335 0.01
TA GND
R361 5.6
C345 10 50V
CD ON
R360 5.6
M+7V
C362 10 50V
100
R304
DATA
R332 1k
REG07-IN
C361 47 16V
R305
XLT
CLOK
REGULATOR
B+ SWITCH
REG07-OUT
C360 10 50V
Q319,320
Q320 KRC402 -RTK
CLOK
+3.3V
C328
Q344,345
R348 1k
10V
R363 18k
Q348 KRC102M-AT R364 6.8k
R318 470
2200
R365 2.2k
SENS Q339 KTC3203Y R353 10
0.01
Q344 2SC2001TP -LK
R317 47k
REGULATOR
C332
R367 2.2k
C357 0.0068
C331
R362 18k
C354 2.2 50V
Q319 KTA1273Y -AT
+3.3V
BIAS OSC
C314 0.01
SENS
Q317 KTC3205Y
C358 0.018
R368 10k
C330 100 10V
R366 22k
SWITCH
C320
C356 0.0068
Q346-348 REC BIAS T301
D303 MTZJ-T-77-3.9B
(Page 25)
AC-DET
Q327 KTA1504
Q328 2SK2158-T2B
D317 1SS133T-77
TA 10V
-B
D321 1SS133T -77
D307 1SS133T -77
Q342,343
R319 1M
D322 1SS133T -77
Q342 2SC1623-T1 -L5L6
Q331 KRA303 -RTK
S
C353 2200 35V
Q343 2SC1623-T1 -L5L6
C355 0.015
6-7.
21
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-NE3
PRINTED WIRING BOARDS – AMP Section – • See page 17 for Circuit Boards Location. MAIN BOARD CNB308 (Page 20)
D AMP BOARD
HP BOARD
R518 9
4
MAIN BOARD CN309 (Page 20)
CNB501
1 CN502
CN501
C
J301 PHONES
1
1
C520
R517
:Uses unleaded solder.
C521
6-8.
C512
R520
R519
7
R515
R516 C511
1-861-728-
C514
JW508
JW509
C513 C510
JW510
C509
EP903 JW513 C507
R511
R507
R506
R502
R505
JW502
JW511
JW506 JW512
IC501
15
JW501
C501
10
14
C506
R508
C505
5
R504
1
R509
2
R512
C516
JW503
JW507
(CHASSIS)
R514
JW505 JW504
R503
C503
R501
11 1-861-726-
22
22
(11)
11 (11)
HCD-NE3
6-9.
SCHEMATIC DIAGRAM – AMP Section –
CN502 9P +B GND -B PROTECT R514
10k
R507
10k
AMP-STBY R512 33k
AMP-MUTE
(Page 21)
L AGND C506 47 25V
R R501 1k
R502 47k
R505 47k
C503 47 25V
R506 1k
C516 100 16V
R508 680
R515 2.2
R516 2.2
C512 1
C514 1
C511 1
C513 1
R517 56k
R519 330
CN501 4P SP OUT(R) HP OUT(R) HP OUT(L)
R518 47k
SP OUT(L)
C507 0.1 R511 33k
R520 330
R503 680 C509 220 35V
C510 220 35V EP903
(CHASSIS GND) C505 100p C501 100p
R509 47k
R504 47k
J301 PHONES
CNB501 7P SP OUT(R) HP OUT(R) HP OUT(L) SP OUT(L) SP OUT(R)
C520 10000p
C521 10000p
GND SP OUT(L) POWER AMP IC501 LM1876TF
(Page 21)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
23
23
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-NE3
• See page 17 for Circuit Boards Location.
6-10. PRINTED WIRING BOARDS – PANEL Section –
BACK LIGHT BOARD
13
15
JR102
JR103
JR106
R833
81
JW803 JW806
80 JW855
JW863
CNB806
D701
JW805 1 JW868
IC801
JR109 R881
JW857
JW858
JW832
JW860
JR101
R810
R818
R815
JW812
D809
D812
D810
JW833
D811
(Page 20) S809
TUNE +
TUNE –
JW846 JW862 R858
D806 (STANDBY)
JW829 JW824
R853
TAPE
JW865 JW848
R851
S802
S801
11
S803
1-861-725-
CD
JW866
R891
R855
JW818
R890
JW822
JW844
JW853
JW843
R885 R886
D801
JW831
Q803
Q806
R883
JW870
JW817
JW845
Q804 E
E R884
C834
JW823
R871
JW815
Q805
R803
R852
R869 C832 JW816
1
D808
JW830 TUNER BAND
1 3
JW826
JW821
R870
R874
Q802
R854
S804
C828
C829
JW820
R879
JW850
R887
R804 C811
C813
3
H
R805
R895
RV801 ROTALY ENCODER VOLUME
JW819
IC803
R816
JW849
C816
JW814
R878
D807
JW828
JW813
G
F MAIN BOARD CN303
R860 S810
L801
JW811
R859
JR105
R814
R813
JW861 JW869
JW847
JW810
C810
S808
JW836
C827
R861
SUPPLIED WITH THE ASSEMBLED BLOCK
C815
R820 R875 (EXCEPT SP, TW, KR, AUS)
R862
JW871
JW809
R806
Q801
R823 R831
JW825
S811 DISPLAY
C823
R897
R822
(EXCEPT US, CND)
C812
F
R809
R706
(US, CND) R701
R863
R705
R812
C805
BASS/TREBLE
(EXCEPT AEP, UK) R876
S813 DSGX
R811
R840
JW842
R898
R824
S812
C824
S801 – 813
R857
R856 CNB801
S806 S805 CD SYNCHRO
REC PAUSE/START
J TAPE MECHANISM DECK BLOCK SUPPLIED WITH THE ASSEMBLED BLOCK
24
FM/AM TUNER PACK
1
R836
R825
31
JW840
30
JW838
R702
X802
E
JW867
3
JW835
R882
(Page 20) C831
C809
R826
C802
C801
X801
R832
R837
IC802
CNB303
R827
JW837
JW807
2
JW839
1
JR104
JW859
50
C830
CNB802
JW808
R801
MAIN BOARD CN302
51
JW864
R703
R704
CNB804
B
JW856
JW834
S820 CD LID OPEN/CLOSE DETECT
C814
C803
100
JW827
JW802
2
(11)
1
I
14
R834
JW801
Q808
R708 R707
11
D
12
R835
C826
G-4 H-10 H-10 H-11 H-10 H-13 C-4
LCD801 LIQUID CRYSTAL DISPLAY
37
R710 R709
1-861-730-
Q801 Q802 Q803 Q804 Q805 Q806 Q808
11
JW804
D701 – 703 LCD BACK LIGHT
C
10
JR107
R894
D-7 D-13 H-4
9
CNB302
R893
IC801 IC802 IC803
8
CONTROL BOARD
2
D702
7
1
R711
B
6
C804
R712
5
R838
A
C825
C-1 B-1 B-1 H-9 G-13 G-3 I-3 F-12 F-11 F-11 F-11
4
R892
D701 D702 D703 D801 D806 D807 D808 D809 D810 D811 D812
3
CNB807
Location
2
D703
Ref. No.
1
R839
• Semiconductor Location
:Uses unleaded solder.
24
S807 PLAY MODE
(11)
FM 75Ω (COAXIAL) ANTENNA AM
HCD-NE3
6-11. SCHEMATIC DIAGRAM – PANEL Section –
• See page 28 for Waveforms.
• See page 30 for IC Pin Function Description.
LCD801
COM0
COM1
COM2
COM3
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG33
LIQUID CRYSTAL DISPLAY
D701-703
R707 120
(LCD BACK LIGHT)
CNB806 2P
COM0
COM1
COM2
COM3
SEG33
SEG32
SEG31
SEG30
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG29
D701 SELS6B14CS-TP5
CNB807 2P
BLTC803
R708 120
R709 120 D702 SELS6B14CS-TP5
0.01
R710 120
BLT+ R832 47k SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG27
R711 120
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
R833 47k
SEG3
SEG2
R851 3.3k
SEG1
R858 3.3k
D703 SELS6B14CS-TP5
R703 10k
S808
R704 100k
CNB302 19P
SEG27
SEG26
SEG25
VDD2
VSS2
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
26
25
BIAS3
S801
SEG13
LED DRIVE
TU RCH
LCD BIAS2
SEG28
LCD BIAS1
SEG29
LCD COM0
SEG30
TU GND TU LCH
SEG31
LCD COM1
TU RCH TU-RCH TU GND TU GND
S803
TU LCH
36
TU 10V 35 TU-CE 32
VSS3
TU LED
100
VDD3
TA LED
1
R838
100
POWER ON TA PLAY SW
SYSTEM CONTROLLER
TA END SW
IC801 LC877456C-53K5-E
92 93
R839
100
TUNE +
S804
30
98 39
NC
TA BIAS TA SOL
AMP STBY I POWER MONITOR
100
35
R831
100
34
R824
100
33
R823
100
32
R840
47k
3.3V(MAIN) GND
R898 100k
C814 0.1
3.9V(SUB)
CNB804 2P
TU DI
RMC
F DATA
CD SCOR
KEY0
KEY1
GND
R897 100k
NC TA-SW
VOL ENCODER
AREA
NC
I POWER DOWN
TU DO
NC
VDD1
CF2
CF1
PWR ON
XT2
CD ON
CD SYNCHRO
VSS1
AU MUTE
S805
R825
TU MUTE
AMP MUTE 100
XT1
DISPLAY
I POWER MONITOR AC-DET R836 4.7k
TU CLK
99
R855 680
36
TU CE
BACK LIGHT ON 98
R861 470
37
100
AC DET
97
S811
100
R826 TU TUNED
96
BAND
R827
4 OPEN/CLOSE GND
R882 100k
D810 L801 10µH 1SS133T-77
R822 30
100
R820 29
56k
100 R818 27
100 R810 26
100 R811 25
100 R815 24
R814 23
47k
R813 22
20p C827 10 16V
R816 22k
AC DET
RV801 ROTALY ENCODER
R875 *
29
R895 10k
R879 10k R701 33k
(US,CND)
R705 27k
D809 1SS133T-77
(EXCEPT SP,TW,KR,AUS)
R706 3.3k
22
(EXCEPT US,CND)
28
11
9
5
4
3
2
18 C801
24
1
R812
R809
C812 0.01
27 SCOR
220k
X802 10MHz
100
390k 22p C802
32.768KHz
0.1 C830
X801
1k
R857 1.5k
R806
100 R805 8
S807 PLAY MODE
100
S813 DSGX
R804
7 SENS
7
R801
8 CLOK
100
R863 1k
9 XLT
R803
6
100
REC PAUSE/START
6
5
22k
S806
3 XTACN XRST DATA
DETECT
R856 1k
S812 BASS/TREBLE
R702
2 CD ON
REMOTE CONTROL RECEIVER IC802 RPM7240-H9
VOLUME R878 10k
C832 0.01
R
C813 0.1
R881 100
V G
CNB801 7P
R869 10k
R870 10k
R874 10k
R876 *
C834 0.1
C828 0.01
(EXCEPT AEP,UK)
C829 0.01
C810 22 6.3V
C831 220p
C809 0.01
PLAY SW
SUPPLIED WITH THE ASSEMBLED
REC PACK
R871 10k
* R875
MOTOR 9V
R887 470
SOL9V
Q804 KTA1271Y-AT
BLOCK COM GND
2.2k (US,CND)
Q802 KTA1271Y-AT
END SW
D811 1SS133T-77
R894 22k 11
R891 4.7k
23
0 (SP,TW,KR,AUS) R886 1k
Q802,803
D801 1SS133T-77
D812 1SS133T-77
D808 1SS133T-77
* R876 R883 47k
4.7k (US,CND,E,E51,EA,MX,AR)
R885 47k
D806 SLR-342VRT32
PLUNGER DRIVE
R890 220
0 (AEP,UK) 1k (E,E51,EA,MX,AR)
(STANDBY)
R884 1k
VOLTAGE DETECT IC803 M62703SL-TP
C811 22 16V
I
Q803 KRC402-RTK
Q805 KRC402-RTK
Q804,805 CAPSTAN/REEL
LED DRIVE
C826 0.1
93
96
92
MOTOR DRIVE
91
Q801 KTC3875
O G
Q806 KRC402-RTK
25
25
TA GND
C824 47 6.3V
39
DECK BLOCK
TA 10V
TAPE MECHANISM
S820 CD LID OPEN/CLOSE
R862 680
CNB303 8P
(Page 21)
AMP-MUTE 18
TU STEREO
TA REC/PLAY
34
99
R837 4.7k
95
TU-CL
AMP-STBY
ST/BY
94
R854 470
TUNER
TU-DO
(Page 21)
MD LED
TA MOTOR
S810
TU-DI
REC/PB
AU-MUTE 91
RESET
BLOCK AM
28
NC
THE ASSEMBLED
CD LED
94
F DATA
R853 330
R860 330
TU 10V
TA BIAS
C805 0.01
NC
CD XLT
TUNED
TA GND 95
NC
CD CLK
STEREO
TA 10V TA GND
NC
CD SENS
TUNER PACK SUPPLIED WITH
R835 47k
CD
37
SEG33
CD DATA
TU-LCH
LCD COM3
CD XRST
FM/AM
SEG32
CD OPEN
COAXIAL
LCD COM2
CD XTXCN
FM 75Ω
ANTENNA
C804 0.01
TU 10V TA 10V
SEG33
S809 TUNE -
TU 10V
SEG32
COM3
TAPE
0.1
33 MUTE
C815
CNB802 11P
C823 470 6.3V
SEG31
COM2
R852 220
TU-LCH
SEG30
COM1 S802
TU GND
SEG29 COM0
R859 220
TU-RCH
SEG28 R834 47k
R712 120
97
Q808 KTC3875
C816 0.1
C825 0.1
RESET
R892 47k
D807 1SS133T-77
SWITCH
R893 47k
HCD-NE3 6-12. PRINTED WIRING BOARD – POWER Board – • Semiconductor Location
3
:Uses unleaded solder.
4
5
6
Location
POWER BOARD (EXCEPT E, E51, EA, SP) (E, E51, EA, SP)
S901
JW909
JW906
-2 -1
VOLTAGE SELECTOR 220 – 240V 220 – 240V
JW904
A
110 – 120V (E, E51, SP) 120 – 127V (EA)
JW907 (EXCEPT E, E51, EA, SP)
B ∗
∗ NOT REPLACEABLE: BUILT IN TRANSFORMER
T902 MAIN POWER TRANSFORMER
C JW908
C908
D919 JW903
R910 T901 SUB POWER TRANSFORMER
D917
C909
C903
C910
R901
D911
R902
D
C901
C902
R904
E
C915
D916
D920
D921
C912
C913
C906 C905
D913
D914
D918
C911 D912
C907
D909
D907 D908
D910
LF901
JW910
R905
D923
RY901
D906
F-4 E-5 E-5 E-4 E-4 D-4 E-5 D-5 E-5 E-5 D-5 E-6 D-6 E-5 E-5 F-5 E-4 F-5
JW912
D906 D907 D908 D909 D910 D911 D912 D913 D914 D916 D917 D918 D919 D920 D921 D922 D923 D924
2
JW901
Ref. No.
1
• See page 17 for Circuit Boards Location.
JW911
8 1
2
D924 R903 (US, CND)
F
1
CN902
C914
CN901
R906
D922
11 1-861-727-
E (AC IN)
26
26
MAIN BOARD CNB301
(Page 20)
(11)
HCD-NE3
6-13. SCHEMATIC DIAGRAM – POWER Board –
T902
D921 1SS133T-77
R902 47k
D916 1N5401M
C908 0.022
D919 1N5401M
D917 1N5401M
C902 0.1
C910 0.022
D913 1N4002B
D911 1N4002B
TRANSFORMER
C901 0.1
C909 0.022 C903 0.1
C912 0.022
D914 1N4002B
D912 1N4002B
-1
-2
C911 0.022
JW909
R910 0.15 S901 VOLTAGE SELECTOR
* NOT REPLACEABLE: BUILT IN TRANSFORMER
R903 3.3M
110-120V
220-240V (E,E51,SP)
120-127V
220-240V (EA)
(E,E51,EA,SP)
CN902 8P
(US,CND)
-B
C913 0.01
GND +B
LF901 SUB +B
RELAY ON
RY901
D906 1SS133T-77
AC-DET
C914 47 25V
R906 *
D909 1SS133T-77
D907 1SS133T-77
D910 1SS133T-77
D908 1SS133T-77
R904 2.2k
R905 2.2k
D923 1SS133T-77
D924 1SS133T-77
JW907
PROTECT
(EXCEPT E,E51,EA,SP)
14V
(Page 21)
(EXCEPT E,E51,EA,SP)
R901 47k
D918 1N5401M
C906 0.022
D920 1SS133T-77
C907 0.022
C905 0.022
MAIN POWER
CN901 2P
(AC IN)
C915 0.1
T901 SUB POWER TRANSFORMER
D922 RB441Q-40T-77
* R906 1k (US,CND,AEP,UK,KR) 1.2k (EXCEPT US,CND,AEP,UK,KR)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
27
27
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-NE3
• Waveforms – BD Board –
– MAIN Board –
– CONTROL Board –
• IC Block Diagrams – BD Board –
1 IC101 w; (TEI) (CD Play mode)
qa T301 4 (REC mode)
wa IC801 qd (XT2)
IC101
XRST
XTACN
IOVSS0
XTSL
LMUT
94 93
92 91 90 89
88
87
86
85
SYSM
DATA
VSS
98 97 96 95
EXCK SBSO SQCK SQSO
100 99
CLOK XLAT
VDD
SENS
ATCK SCLK
WFCK
XUGF
XPCK
C2PO
108 107 106 105 104 103 102 101
112 111 110 109
Approx. 400 mVp-p
GFS
SCOR
VDD
C4M
WDCK
COUT
CXD3058AR
3 Vp-p
150 Vp-p
CPU INTERFACE
SERVO INTERFACE
13 µs
30.5 µs
84 RMUT 83 IOVDD0
2 IC101 ws (FEI) (CD Play mode)
qs Q344 (Collector) (REC mode)
ws IC801 qh (CF2) 82 AVDD2 D/A COVERTER
Approx. 200 mVp-p
2.9 Vp-p
15 Vp-p
MIRR 1 DFCT 2 FOK 3
81 AOUT2 80 VREFR
LPF
MIRR DFCT FOK
79 AVSS2 78 AVSS1
VSS 4
77 VREFL 76 AOUT1
LPF
LOCK 5 MDP 6
75 AVDD1
SSTP 7
74 XVDD
IOVSS1 8
13 µs
SFDR SRDR TFDR TRDR FFDR FRDR
100 ns
3 IC101 ek (RFACO) (CD Play mode)
73 XTAI 72 XTAO
CLOCK GENERATOR
9 10 11 12 13 14
71 XVSS
PWM GENERATOR SERVO AUTO SEQUENCER
DIGITAL CLV
70 IOVSS2 69 TES1 68 TEST
IOVDD1 15 AVDD0 16
SERVO DSP
AVSS0 17
67 DOUT
DIGITAL OUT
0.6 Vp-p
66 IOVDD2 A/D CONVERTER
65 EMPHI 64 EMPH
E F TEI TEO
4 IC101 us (XTAO) (CD Play mode)
63 VDD
18 19 20 21
D/A INTERFACE
TE
SELECTOR ERROR CORRECTOR
FEI 22 FEO 23 VC 24
62 BCK 61 PCMD 60 VSS
32k RAM
59 LRCK
FE
VC
EFM DEMODULATOR A B C D
3.4 Vp-p
25 26 27 28
SUM
SUB CODE PROCESSOR
ASYNMMETRY CORRECTOR
59 ns
ATT
EQ
DIGITAL PLL
AMP
DC/DC CONVERTER
58 LRCKI 57 PCMDI
28
28
DDVROUT DDVRSEN
BCKI
DDCR
AVDD5
AVSS5
CLTV FILO FILI PCO
AVSS3
56
VPCO VCTL
52 53 54 55
BIAS ASYI ASYO
RFC
51
AVDD3
PD
39 40 41 42 43 44 45 46 47 48 49 50
RFACI
36 37 38
AVSS4
35
RFACO
33 34
LD
AC_SUM
RFDCO
PDSENS
AVDD4
29 30 31 32
EQ_IN
APC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PB1N
PB1P
PB2P
PB2N
PB2O
PB1O
VOLIN1
VOLIN2
GND
TRE1
TRE2
VDD
CONT
VEE
REC1O
REC1N
REC2N
REC2O
INC2 INC1 INB2 INB1 INA2 INA1
OUT1 BAS1
OUT2 BAS2
IC302 6 7 10
VOLUME
28 27 26 25 24 23 22 21 20 19 18 17 16 15
BASS
VOLUME
TREBLE
CH1OUTF
VREF
CH1OUTR
MUTING
CH2OUTF
CH2OUTR
9
POWVCC
8
VREFIN
GND
5
CH2RIN
4
CH2FIN
3
CH1RIN
1 2
CH1FIN
OPOUT
OUTVREF
CH4CAPA
CH4IN
CH3FIN
CH3RIN
GND
MUTE
POWVCC
CH3OUTF
CH3OUTR
CH4OUTF
CH4OUTR
IC251
SW
OPIN– OPIN+
PREVCC
HCD-NE3
BA5947FM
28 27 26 25 24 23 22 21 20 19 18 17 16 15
D D D D
+ – INTERFACE LEVEL SHIFT
INTERFACE INTERFACE
D D D D
11 12 13 14
– MAIN Board –
BD3881FV
BASS
TREBLE
LOGIC CONTROL
29
+ –
HCD-NE3
• IC Pin Function Description
CONTROL BOARD IC801 LC877456C-53K5-E (SYSTEM CONTROLLER) Pin No.
Pin Name
I/O
1
PWR ON
O
Power relay drive signal output terminal
2
CD ON
O
Power on/off control signal output for the CD mechanism section
3
CD XTXCN
O
Oscillation circuit control signal output to the CD DSP “H”: auto oscillation, “L”: oscillation off
4
CD OPEN
I
CD lid open/close detection switch input terminal
5
CD XRST
O
Reset signal output to the CD DSP
6
CD DATA
O
Serial data output to the CD DSP
7
CD SENS
I
Internal status (SENSE) signal input from the CD DSP
8
CD CLK
O
Serial data transfer clock signal output to the CD DSP
9
CD XLT
O
Serial data latch pulse output to the CD DSP
10
NC
—
Not used
11
RESET
I
Reset signal input from the reset switch “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
12
XT1
I
Sub system clock input terminal (32.768 kHz)
13
XT2
O
Sub system clock output terminal (32.768 kHz)
14
VSS1
—
Ground terminal
15
CF1
I
Main system clock input terminal (10 MHz)
16
CF2
O
Main system clock output terminal (10 MHz)
17
VDD1
—
Power supply terminal (+3.2V)
18
I POWER MONITOR
I
19, 20
NC
—
21
AREA
I
Model destination setting terminal
22
VOL ENCODER
I
Dial pulse input of the rotary encoder (for VOLUME control)
23
I POWER DOWN
I
Power down detection signal input terminal
24
TA-SW
I
Cassette in/out detect switch signal input from the tape mechanism deck
25, 26
KEY1, KEY0
I
Front panel key input terminal (A/D input)
27
CD SCOR
I
Subcode sync (S0+S1) detection signal input from the CD DSP
28
F DATA
O
Serial data output to the electrical volume
29
RMC
I
Remote control signal input from the remote control receiver
30
TU DI
I
Serial data input from the FM/AM tuner unit
31
NC
—
Not used
32
TU DO
O
Serial data output to the FM/AM tuner unit
33
TU MUTE
O
Tuner muting on/off control signal output to the FM/AM tuner unit
34
TU CLK
O
serial data transfer clock signal output to the FM/AM tuner unit
35
TU CE
O
Chip enable signal output to the FM/AM tuner unit
36
TU TUNED
I
Tuning detection signal input from the FM/AM tuner unit
37
TU STEREO
I
FM stereo detection signal input from the FM/AM tuner unit
38
NC
—
Not used
39
ST/BY
O
LED drive signal output terminal
40
MD LED
O
LED drive signal output terminal
30
Description “H”: on
Power monitor input terminal Not used
“L”: power down, normally : “H” “L”: cassette in
HCD-NE3
Pin No.
Pin Name
I/O
41
TA LED
O
LED drive signal output terminal
42
TU LED
O
LED drive signal output terminal
43
CD LED
O
LED drive signal output terminal
44
NC
—
Not used
O
Segment drive signal output to the fluorescent indicator tube
45 to 53 SEG33 to SEG25
Description
54
VDD2
—
Power supply terminal (+3.1V)
55
VSS2
—
Ground terminal
56 to 79
SEG24 to SEG1
O
Segment drive signal output to the fluorescent indicator tube
80
BIAS3
I
Power supply output for the liquid crystal display bias
81
LCD BIAS2
I
Power supply output for the liquid crystal display bias
82
LCD BIAS1
I
Power supply output for the liquid crystal display bias
83 to 86
LCD COM0 to LCD COM3
O
Common drive signal output to the liquid crystal display (D621)
87, 88
NC
—
Not used
89
VSS3
—
Ground terminal
90
VDD3
—
Power supply terminal (+3.1V)
91
TA PLAY SW
I
PLAY switch signal input from the tape mechanism deck
92
TA END SW
I
END switch signal input from the tape mechanism deck
93
TA MOTOR
O
Capstan/reel motor on/off control signal output terminal
94
TA REC/PLAY
O
Recording/playback selection signal output terminal
95
TA BIAS
O
Recording bias on/off selection signal output terminal “H”: bias on, “L”: bias off
96
TA SOL
O
Trigger plunger on/off control signal output terminal
97
BACK LIGHT ON
O
LED drive signal output terminal for the LCD back light
98
AMP STBY
O
Standby control signal output to the power amplifier
99
AMP MUTE
O
Tuner muting on/off control signal output to the power amplifier
100
AU MUTE
O
Line muting on/off control signal output terminal
“H”: motor on
“H”: playback mode, “L”: recording mode
“H”: plunger on
Not used
31
HCD-NE3 SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they are seldom required for routine service. Some may have some difference from the original delay should be anticipated when ordering one. these items. • Color Indication of Appearance Parts • The mechanical parts with no reference numExample: ber in the exploded views are not supplied. KNOB, BALANCE (WHITE) . . . (RED) • Accessories are given in the last of the elec↑ ↑ trical parts list. Parts Color Cabinet's Color • Abbreviation AR : Argentina model E51 : Chilean and Peruvian model MX : Mexican model AUS : Australian model EA : Saudi Arabia model SP : Singapore model CND : Canadian model KR : Korea model TW : Taiwan model
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
7-1. PANEL SECTION
not supplied
3 #1 #1
6
top panel assy #8 not supplied (REG board) (1/2)
8 #8
#8 #1
not supplied #1
#1 #8
#8
2
5
#8
front panel assy-1 #1
10
4 #1
#5
#1
7 #1
9
#1 not supplied not supplied (REG board) (2/2) Ref. No.
Part No.
Description
1 1 1 1 1
A-1055-614-A A-1056-003-A A-1056-266-A A-1056-495-A A-1056-526-A
POWER BOARD, COMLETE (E, E51, SP) POWER BOARD, COMLETE (AR, AUS) POWER BOARD, COMLETE (MX, TW) POWER BOARD, COMLETE (EA) POWER BOARD, COMLETE (KR)
1 1 2 3 4
A-4750-273-A A-4751-335-A A-4750-277-A A-4750-275-A 3-703-244-00
POWER BOARD, COMLETE (AEP, UK) POWER BOARD, COMLETE (US, CND) AMP BOARD, COMPLETE MAIN BOARD, COMPLETE BUSHING (2104), CORD
05 05 05 05 05
1-775-790-12 1-769-079-23 1-769-744-52 1-696-570-21 1-783-531-22
CORD, POWER (AUS) CORD, POWER (KR) CORD, POWER (AEP, UK, E51, SP) CORD, POWER (EA) CORD, POWER (US, CND)
05 05 05
1-829-387-11 CORD, POWER (AR) 1-827-226-11 CORD, POWER (E, MX) 1-827-597-31 CORD, POWER (TW)
32
Remark
1
T902 Ref. No. 6 6 6 7 8 9 10 0 T902
Part No.
Description
Remark
1-693-625-11 TUNER (FM/AM) (US, CND) 1-693-628-11 TUNER (FM/AM) (E, E51, EA, MX, SP, TW, AR, AUS) 1-693-629-11 TUNER (FM/AM) (AEP, UK, KR) 4-246-784-01 FOOT RUBBER 4-253-221-01 CABINET, REAR
0 T902 0 T902
3-701-748-00 CLAMP 1-500-386-11 FILTER, CLAMP (FERRITE CORE) 1-443-246-11 TRANSFORMER, POWER (E, E51, MX, SP, TW, AR, AUS) 1-443-245-11 TRANSFORMER, POWER (AEP, UK) 1-443-244-11 TRANSFORMER, POWER (US, CND)
0 T902 0 T902 #1 #8 #5
1-443-396-11 1-443-397-11 7-685-647-79 7-685-646-79 7-685-661-14
TRANSFORMER, POWER (EA) TRANSFORMER, POWER (KR) SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTP 4X12 TYPE2 N-S
HCD-NE3
7-2. FRONT PANEL ASSY-1
57 not supplied
54 57
not supplied
not supplied (back light board)
57
not supplied not supplied
55 not supplied
not supplied (HP board)
not supplied
51
front panel assy-2
Ref. No.
Part No.
Description
Remark
51 54 54 54 54
4-253-222-01 A-1055-611-A A-1056-204-A A-1056-001-A A-1056-250-A
KNOB, VOLUME CONTROL BOARD, COMPLETE (SP) CONTROL BOARD, COMPLETE (E, E51, AR) CONTROL BOARD, COMPLETE (TW, AUS) CONTROL BOARD, COMPLETE (MX)
54
A-1056-496-A CONTROL BOARD, COMPLETE (EA)
Ref. No. 54 54 54 55 57
Part No.
Description
Remark
A-1056-524-A A-4750-270-A A-4751-333-A 3-921-725-01 4-951-620-11
CONTROL BOARD, COMPLETE (KR) CONTROL BOARD, COMPLETE (AEP, UK) CONTROL BOARD, COMPLETE (US, CND) SCREW (2.6X10), +PWH SCREW (2.6X10), +BVTP
33
HCD-NE3
7-3. FRONT PANEL ASSY-2
106
107 108
not supplied
104 109
103
105 #6 not supplied
112 111
101
102
111 111 not supplied
110
Ref. No.
Part No.
Description
101 102 103 104 105
X-4956-276-1 4-245-034-01 4-245-018-01 4-238-631-01 4-246-784-01
LID, CASS ASSY (X) SPRING (CASSETTE) HOLDER (CASSETTE) TAPE SPRING FOOT RUBBER
106
X-2022-201-1 PANEL ASSY, FRONT (E, E51, EA, MX, SP, TW, AR, AUS) X-4956-274-1 PANEL ASSY, FRONT (AEP, UK, KR)
106
34
Remark
Ref. No.
Part No.
Description
106 107 108 109 110
X-4956-277-1 4-231-841-01 4-231-825-01 4-224-104-41 1-796-352-41
PANEL ASSY, FRONT (US, CND) SPRING (HEART CAM-B) CAM (B), HEART DAMPER DECK, MECHANICAL (CMAL5Z220A)
111 112 #6
4-951-620-11 SCREW (2.6X10), +BVTP 3-701-748-00 CLAMP 7-685-862-09 SCREW +BVTT 2.6X6 (S)
Remark
HCD-NE3
159
7-4. TOP PANEL ASSY
158 160 157 156 168
155 161
S820 not supplied
154 167 153 154
153 151 163
151
152
166
S101
not supplied
169
not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No.
Part No.
Description
151 152 153 154 155
3-921-725-01 4-247-493-01 3-931-379-31 3-931-379-21 4-242-171-01
SCREW (2.6X10), +PWH COVER, CD RUBBER, VIBRATION PROOF (GREEN) RUBBER, VIBRATION PROOF (RED) DAMPER 150 N
156 157 158 159 160
4-246-193-01 4-249-238-01 4-246-192-01 X-4956-278-1 4-246-191-11
HOLDER, CHUCK A MAGNET (18-30-5) BASE, CHUCK N CD ASSY, LID PLATE, MAGNET
Remark
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
161 161 163 166 0 167
4-245-015-21 4-245-015-31 1-827-991-11 A-4751-032-A 8-820-221-01
CABINET (TOP) (US, CND) CABINET (TOP) (EXCEPT US, CND) WIRE (FLAT TYPE) (16 CORE) BD BOARD, COMPLETE OPTICAL PICK-UP KSM-213EDP/C2NP
Remark
168 169 S101
4-248-711-11 SPRING (CD) 4-951-620-01 SCREW (2.6X8), +BVTP 1-771-853-11 SWITCH, DETECTION (LIMIT)
S820
1-692-960-11 SWITCH, PUSH (1KEY) (CD LID OPEN/CLOSE DETECT)
35
HCD-NE3 BACK LIGHT
AMP
SECTION 8 ELECTRICAL PARTS LIST
BD
NOTE: • Items marked “*” are not stocked since they • Due to standardization, replacements in the are seldom required for routine service. parts list may be different from the parts speciSome delay should be anticipated when orderfied in the diagrams or the components used ing these items. on the set. • SEMICONDUCTORS • -XX and -X mean standardized parts, so they In each case, u: µ, for example: may have some difference from the original uA. . : µA. . uPA. . : µPA. . one. uPB. . : µPB. . uPC. . : µPC. . • RESISTORS uPD. . : µPD. . All resistors are in ohms. • CAPACITORS METAL: Metal-film resistor. uF: µF METAL OXIDE: Metal oxide-film resistor. • COILS F: nonflammable uH: µH • Abbreviation AR : Argentina model E51 : Chilean and Peruvian model MX : Mexican model AUS : Australian model EA : Saudi Arabia model SP : Singapore model CND : Canadian model KR : Korea model TW : Taiwan model Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Description
Remark
R518 1-216-841-11 METAL CHIP 47K 5% 1/10W 0 R519 1-215-889-00 METAL OXIDE 330 5% 2W F 0 R520 1-215-889-00 METAL OXIDE 330 5% 2W F ************************************************************
A-4750-277-A AMP BOARD, COMPLETE ******************** < CAPACITOR > C501 C503 C505 C506 C507
1-162-927-11 1-126-947-11 1-162-927-11 1-126-947-11 1-107-826-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP
100PF 47uF 100PF 47uF 0.1uF
5% 20% 5% 20% 10%
50V 35V 50V 35V 16V
C509 C510 C511 C512 C513
1-126-949-11 1-126-949-11 1-136-177-00 1-136-177-00 1-136-177-00
ELECT ELECT FILM FILM FILM
220uF 220uF 1uF 1uF 1uF
20% 20% 5% 5% 5%
35V 35V 50V 50V 50V
C514 C516
1-136-177-00 FILM 1-126-933-11 ELECT
1uF 100uF
5% 20%
50V 16V
BACK LIGHT BOARD **************** < LED > D701
8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT)
D702
8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT)
D703
8-719-075-50 LED SELS6B14C-TP5 (LCD BACK LIGHT) < RESISTOR >
< CONNECTOR > CN501
1-564-507-11 PLUG, CONNECTOR 4P
120 120 120 120 120
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
A-4751-032-A BD BOARD, COMPLETE ****************** < CAPACITOR >
8-759-333-24 IC LM1876TF < RESISTOR >
R501 R502 R503 R504 R505
1-216-821-11 1-216-841-11 1-216-819-11 1-249-437-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP
1K 47K 680 47K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/4W 1/10W
R506 R507 R508 R509 R511
1-216-821-11 1-216-833-11 1-216-819-11 1-249-437-11 1-216-839-11
METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP
1K 10K 680 47K 33K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/4W 1/10W
R512 R514 0 R515 0 R516 R517
1-216-839-11 1-216-833-11 1-216-373-81 1-216-373-81 1-216-842-11
METAL CHIP METAL CHIP METAL OXIDE METAL OXIDE METAL CHIP
33K 10K 2.2 2.2 56K
5% 5% 5% 5% 5%
1/10W 1/10W 2W F 2W F 1/10W
36
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1-537-770-21 TERMINAL BOARD, GROUND < IC >
IC501
1-216-810-11 1-216-810-11 1-216-810-11 1-216-810-11 1-216-810-11
R712 1-216-810-11 METAL CHIP 120 5% 1/10W ************************************************************
< EARTH TERMINAL > EP903
R707 R708 R709 R710 R711
C10 C11 C14 C15 C16
1-165-989-11 1-165-989-11 1-164-360-11 1-164-360-11 1-115-156-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10uF 10uF 0.1uF 0.1uF 1uF
10% 10%
6.3V 6.3V 16V 16V 10V
C17 C18 C111 C112 C113
1-126-923-11 1-162-964-11 1-162-967-11 1-164-315-11 1-162-967-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
220uF 0.001uF 0.0033uF 470PF 0.0033uF
20% 10% 10% 5% 10%
16V 50V 50V 50V 50V
C114 C115 C116 C117 C122
1-164-315-11 1-164-360-11 1-126-923-11 1-164-360-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
470PF 0.1uF 220uF 0.1uF 0.1uF
5% 20% 10%
50V 16V 16V 16V 16V
C123 C124
1-107-826-11 CERAMIC CHIP 1-162-959-11 CERAMIC CHIP
0.1uF 330PF
10% 5%
16V 50V
HCD-NE3 BD Ref. No.
Part No.
Description
Remark
JR111
25V 16V 50V 16V 16V
Q10
1-164-360-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-125-891-11 CERAMIC CHIP
0.1uF 100PF 0.47uF
C133 C141 C142 C143 C151
1-162-970-11 1-107-826-11 1-162-965-11 1-164-360-11 1-126-923-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.01uF 0.1uF 0.0015uF 0.1uF 220uF
C160 C161 C162 C163 C164
1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
C170 C171 C172 C174 C181
1-126-934-11 1-162-919-11 1-162-920-11 1-164-360-11 1-164-360-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
220uF 22PF 27PF 0.1uF 0.1uF
C182 C183 C184 C185 C186
1-164-360-11 1-126-923-11 1-126-923-11 1-164-315-11 1-164-315-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
0.1uF 220uF 220uF 470PF 470PF
C194 C195 C201 C202 C203
1-164-360-11 1-164-360-11 1-126-923-11 1-164-360-11 1-126-923-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
0.1uF 0.1uF 220uF 0.1uF 220uF
20% 20%
16V 16V 16V 16V 16V
C210 C211 C212 C213 C251
1-107-826-11 1-164-230-11 1-162-919-11 1-162-919-11 1-162-969-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 220PF 22PF 22PF 0.0068uF
10% 5% 5% 5% 10%
16V 50V 50V 50V 25V
C252 C257 C258 C259
1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF
< CONNECTOR > CN101 CN201
1-793-907-11 CONNECTOR, FFC/FPC 16P 1-568-860-11 SOCKET, CONNECTOR 17P
5% 10% 10% 10% 10% 20%
16V 16V 16V 16V 16V 20% 5% 5%
20% 20% 5% 5%
Ref. No.
16V 50V 10V
C125 C131 C132
16V 50V 50V 16V 16V 16V 16V 16V 50V 50V
16V 16V 16V 16V
Part No.
CONTROL
Description
1-216-296-11 SHORT CHIP
Remark 0
< TRANSISTOR > 6-550-363-01 TRANSISTOR
2SB1690KT146
< RESISTOR/FERRITE BEAD >
R10 R11 R12 R13 R111
1-216-791-11 1-216-864-11 1-216-845-11 1-218-446-11 1-216-821-11
METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP
3.3 0 100K 1 1K
5%
1/10W
5% 5% 5%
1/10W 1/10W 1/10W
R112 R113 R114 R121 R131
1-216-835-11 1-216-821-11 1-216-835-11 1-216-835-11 1-216-857-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
15K 1K 15K 15K 1M
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R132 R133 R141 R142 R143
1-216-833-11 1-216-848-11 1-216-829-11 1-216-821-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 180K 4.7K 1K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R151 R161 R162 R171 R172
1-216-864-11 1-216-809-11 1-216-841-11 1-216-817-11 1-216-857-11
SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 100 47K 470 1M
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R173 R181 R182 R201 R202
1-216-295-00 1-216-809-11 1-216-809-11 1-500-445-21 1-216-864-11
SHORT CHIP 0 METAL CHIP 100 5% METAL CHIP 100 5% FERRITE, EMI (SMD) (2012) SHORT CHIP 0
R204 R251 R252 R406 R407
1-500-445-21 1-216-833-11 1-216-837-11 1-216-809-11 1-216-809-11
FERRITE, EMI (SMD) (2012) METAL CHIP 10K METAL CHIP 22K METAL CHIP 100 METAL CHIP 100
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R408 R409 R410 R411 R412
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
100 100 100 100 100
1/10W 1/10W
< IC > < VIBRATOR > IC101 IC251
8-752-425-11 IC CXD3058AR 6-705-808-01 IC BA5947FM
X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************
< SHORT > JR101 JR102 JR103 JR104 JR105
1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
JR106 JR107 JR108 JR109 JR110
1-216-296-11 1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
A-1055-611-A A-1056-001-A A-1056-204-A A-1056-250-A A-1056-496-A
CONTROL BOARD, COMPLETE (SP) CONTROL BOARD, COMPLETE (TW, AUS) CONTROL BOARD, COMPLETE (E, E51, AR) CONTROL BOARD, COMPLETE (MX) CONTROL BOARD, COMPLETE (EA)
A-1056-524-A CONTROL BOARD, COMPLETE (KR) A-4750-270-A CONTROL BOARD, COMPLETE (AEP, UK) A-4751-333-A CONTROL BOARD, COMPLETE (US, CND) ************************ 4-245-030-01 HOLDER (LCD) 4-245-801-01 SHEET (LCD)
37
HCD-NE3 CONTROL Ref. No.
Part No.
Description
Remark
Ref. No. JR109
4-248-365-01 SHEET (PLATE) 4-248-366-01 SHEET (LIGHT)
Part No.
Description
1-216-864-11 SHORT CHIP
Remark 0
< COIL > < CAPACITOR > L801 C801 C802 C803 C804 C805
1-164-160-11 1-162-919-11 1-107-726-91 1-107-726-91 1-107-726-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
20PF 22PF 0.01uF 0.01uF 0.01uF
5% 5% 10% 10% 10%
50V 50V 16V 16V 16V
C809 C810 C811 C812 C813
1-107-726-91 1-124-222-91 1-124-234-00 1-107-726-91 1-107-826-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
0.01uF 22uF 22uF 0.01uF 0.1uF
10% 20% 20% 10% 10%
16V 6.3V 16V 16V 16V
C814 C815 C816 C823 C824
1-107-826-11 1-107-826-11 1-107-826-11 1-104-655-91 1-124-589-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
0.1uF 0.1uF 0.1uF 470uF 47uF
10% 10% 10% 20% 20%
16V 16V 16V 6.3V 16V
C825 C826 C827 C828 C829
1-107-826-11 1-107-826-11 1-126-157-11 1-107-726-91 1-107-726-91
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 10uF 0.01uF 0.01uF
10% 10% 20% 10% 10%
16V 16V 16V 16V 16V
C830 C831 C832 C834
1-107-826-11 1-164-230-11 1-107-726-91 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 220PF 0.01uF 0.1uF
10% 5% 10% 10%
16V 50V 16V 16V
1-410-509-11 INDUCTOR
10uH
< LIQUID CRYSTAL DISPLAY > LCD801 1-805-530-11 DISPLAY PANEL, LIQUID CRYSTAL < TRANSISTOR >
< CONNECTOR > CNB302 CNB303 CNB801 CNB802
1-784-780-11 1-691-040-31 1-568-826-11 1-568-830-11
CONNECTOR, FFC 19P CONNECTOR, FFC 8P CONNECTOR, FFC 7P CONNECTOR, FFC 11P < DIODE >
D801 D806 D807 D808 D809
8-719-991-33 8-719-060-44 8-719-991-33 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
1SS133T-77 SLR-342VRT32 1SS133T-77 1SS133T-77 1SS133T-77
D810 D811 D812
8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 < IC >
IC801 IC802 IC803
6-804-383-01 IC LC877456C-53K5-E 6-600-309-01 IC RPM7240-H9 8-759-532-64 IC M62703SL-TP < SHORT >
JR101 JR102 JR103 JR104 JR105
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
JR106 JR107
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP
0 0
38
Q801 Q802 Q803 Q804 Q805
8-729-034-51 8-729-037-13 8-729-054-16 8-729-037-13 8-729-054-16
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
KTC3875 KTA1271Y KRC402-RTK KTA1271Y KRC402-RTK
Q806 Q808
8-729-054-16 TRANSISTOR 8-729-034-51 TRANSISTOR
KRC402-RTK KTC3875
< RESISTOR > R701
1-216-839-11 METAL CHIP
33K
5%
1/10W (US, CND) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W (EXCEPT US, CND)
R702 R703 R704 R705
1-216-852-11 1-216-833-11 1-216-845-11 1-216-838-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
390K 10K 100K 27K
R706
1-216-827-11 METAL CHIP
3.3K
R801 R803 R804 R805
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100
R806 R809 R810 R811 R812
1-216-821-11 1-216-849-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 220K 100 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R813 R814 R815 R816 R818
1-216-837-11 1-216-841-11 1-216-809-11 1-216-837-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 47K 100 22K 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R820 R822 R823 R824 R825
1-216-842-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
56K 100 100 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R826 R827 R831 R832 R833
1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 10K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R834 R835 R836 R837 R838
1-216-841-11 1-216-841-11 1-216-829-11 1-216-829-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 47K 4.7K 4.7K 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R839
1-216-809-11 METAL CHIP
100
5%
1/10W
5% 1/10W (EXCEPT US, CND) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W
HCD-NE3 CONTROL Ref. No.
Part No.
Description
R840 R851 R852 R853
1-216-841-11 1-216-827-11 1-216-813-11 1-216-815-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 3.3K 220 330
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
Remark
R854 R855 R856 R857 R858
1-216-817-11 1-216-819-11 1-216-821-11 1-216-823-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 680 1K 1.5K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R859 R860 R861 R862 R863
1-216-813-11 1-216-815-11 1-216-817-11 1-216-819-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
220 330 470 680 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R869 R870 R871 R874 R875
1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 10K 10K 1K
Ref. No.
Part No.
HP
MAIN
Description
Remark
S808 S809 S810
1-786-050-21 SWITCH, KEY BOARD (x) 1-786-050-21 SWITCH, KEY BOARD (TUNE – . m) 1-786-050-21 SWITCH, KEY BOARD (TUNE + M >)
S811 S812
1-786-050-21 SWITCH, KEY BOARD (DISPLAY) 1-786-050-21 SWITCH, KEY BOARD (BASS/TREBLE)
S813
1-786-050-21 SWITCH, KEY BOARD (DSGX)
< VIBRATOR >
2.2K
5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W (E, E51, EA, MX, AR)
R875
1-216-825-11 METAL CHIP
5%
R875 R876
1-216-864-11 SHORT CHIP 1-216-829-11 METAL CHIP
R876
1-216-864-11 SHORT CHIP
0 (SP, TW, KR, AUS)
R878
1-216-833-11 METAL CHIP
10K
5%
1/10W
R879 R881 R882 R883 R884
1-216-833-11 1-247-807-31 1-216-845-11 1-216-841-11 1-216-821-11
METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP
10K 100 100K 47K 1K
5% 5% 5% 5% 5%
1/10W 1/4W 1/10W 1/10W 1/10W
R885 R886 R887 R890 R891
1-216-841-11 1-216-821-11 1-216-817-11 1-216-813-11 1-216-829-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 1K 470 220 4.7K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R892 R893 R894 R895 R897
1-216-841-11 1-216-841-11 1-216-837-11 1-216-833-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 47K 22K 10K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R898
1-216-845-11 METAL CHIP
100K
5%
1/10W
X801
1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
X802 1-795-004-21 VIBRATOR, CERAMIC (10MHz) ************************************************************ HP BOARD ********* < CAPACITOR > C520 C521
1-127-876-21 CERAMIC 1-127-876-21 CERAMIC
1/10W (US, CND)
0 (AEP, UK) 4.7K 5% 1/10W (US, CND, E, E51, EA, MX, AR)
0.01uF 0.01uF
10% 10%
50V 50V
< JACK > J301 1-793-829-11 JACK, HEADPHONE (PHONES) ************************************************************ A-4750-275-A MAIN BOARD, COMPLETE ********************* < CAPACITOR >
< ROTARY ENCODER > RV801
1-418-632-11 ENCODER, ROTARY (12 TYPE) (VOLUME)
< SWITCH > S801 S802 S803 S804 S805
1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21
SWITCH, KEY BOARD (I/1) SWITCH, KEY BOARD (TAPE N) SWITCH, KEY BOARD (CD NX) SWITCH, KEY BOARD (TUNER, BAND) SWITCH, KEY BOARD (CD SYNCHRO)
S806 S807
1-786-050-21 SWITCH, KEY BOARD (z REC PAUSE/START) 1-786-050-21 SWITCH, KEY BOARD (PLAY MODE)
C101 C102 C103 C104 C106
1-162-925-11 1-162-977-11 1-162-927-11 1-104-665-11 1-164-227-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
68PF 0.0018uF 100PF 100uF 0.022uF
5% 10% 5% 20% 10%
50V 50V 50V 25V 25V
C107 C108 C109 C110 C111
1-126-961-11 1-162-967-11 1-162-962-11 1-164-218-11 1-162-967-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
2.2uF 0.0033uF 470PF 180PF 0.0033uF
20% 10% 10% 5% 10%
50V 50V 50V 50V 50V
C112 C113 C114 C115 C116
1-162-968-11 1-126-957-11 1-126-959-11 1-126-963-11 1-162-962-11
CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP
0.0047uF 0.22uF 0.47uF 4.7uF 470PF
10% 20% 20% 20% 10%
50V 50V 50V 50V 50V
C117 C118 C119 C121 C126
1-164-730-11 1-164-677-11 1-107-726-91 1-107-826-11 1-162-960-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0012uF 0.033uF 0.01uF 0.1uF 220PF
10% 10% 10% 10% 10%
50V 16V 16V 16V 50V
C127 C132 C133 C134 C135
1-162-962-11 1-126-963-11 1-130-491-00 1-162-966-11 1-126-964-11
CERAMIC CHIP ELECT MYLAR CERAMIC CHIP ELECT
470PF 4.7uF 0.047uF 0.0022uF 10uF
10% 20% 5% 10% 20%
50V 50V 50V 50V 50V
C136 C201 C202 C203
1-126-964-11 1-162-925-11 1-162-977-11 1-162-927-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10uF 68PF 0.0018uF 100PF
20% 5% 10% 5%
50V 50V 50V 50V
39
HCD-NE3 MAIN Ref. No.
Part No.
Description
Remark
C204
1-104-665-11 ELECT
100uF
20%
25V
C206 C207 C208 C209 C210
1-164-227-11 1-126-961-11 1-162-967-11 1-162-962-11 1-164-218-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 2.2uF 0.0033uF 470PF 180PF
10% 20% 10% 10% 5%
25V 50V 50V 50V 50V
C211 C212 C213 C214 C215
1-162-967-11 1-162-968-11 1-126-957-11 1-126-959-11 1-126-963-11
CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT
0.0033uF 0.0047uF 0.22uF 0.47uF 4.7uF
10% 10% 20% 20% 20%
50V 50V 50V 50V 50V
C216 C217 C218 C219 C221
1-162-962-11 1-164-730-11 1-164-677-11 1-107-726-91 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
470PF 0.0012uF 0.033uF 0.01uF 0.1uF
10% 10% 10% 10% 10%
50V 50V 16V 16V 16V
C226 C227 C232 C233 C234
1-162-960-11 1-162-962-11 1-126-963-11 1-130-491-00 1-162-966-11
CERAMIC CHIP CERAMIC CHIP ELECT MYLAR CERAMIC CHIP
220PF 470PF 4.7uF 0.047uF 0.0022uF
10% 10% 20% 5% 10%
50V 50V 50V 50V 50V
C235 C236 C301 C302 C305
1-126-964-11 1-126-964-11 1-162-915-11 1-104-655-91 1-104-655-91
ELECT ELECT CERAMIC CHIP ELECT ELECT
10uF 10uF 10PF 470uF 470uF
20% 20% 0.5PF 20% 20%
50V 50V 50V 6.3V 6.3V
C308 C309 C310 C311 C312
1-107-826-11 1-126-767-11 1-127-888-21 1-128-809-11 1-162-960-11
CERAMIC CHIP ELECT CERAMIC CERAMIC CERAMIC CHIP
0.1uF 1000uF 0.1uF 100PF 220PF
10% 20% 10% 5% 10%
16V 16V 50V 50V 50V
C313 C314 C315 C316 C317
1-126-933-11 1-137-150-11 1-128-809-11 1-162-927-11 1-128-809-11
ELECT FILM CERAMIC CERAMIC CHIP CERAMIC
100uF 0.01uF 100PF 100PF 100PF
20% 5% 5% 5% 5%
16V 100V 50V 50V 50V
C318 C319 C320 C321 C322
1-162-927-11 1-162-927-11 1-107-726-91 1-115-416-11 1-115-416-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 0.01uF 0.001uF 0.001uF
5% 5% 10% 5% 5%
50V 50V 16V 25V 25V
C323 C324 C326 C328 C329
1-126-943-11 1-126-934-11 1-162-966-11 1-126-935-11 1-126-916-11
ELECT ELECT CERAMIC CHIP ELECT ELECT
2200uF 220uF 0.0022uF 470uF 1000uF
20% 20% 10% 20% 20%
25V 16V 50V 16V 6.3V
C330 C331 C332 C333 C335
1-104-665-11 1-107-726-91 1-126-927-11 1-126-969-11 1-107-726-91
ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP
100uF 0.01uF 2200uF 220uF 0.01uF
20% 10% 20% 20% 10%
25V 16V 10V 50V 16V
C336 C345 C346 C351 C352
1-126-965-11 1-126-964-11 1-126-768-11 1-104-665-11 1-126-953-11
ELECT ELECT ELECT ELECT ELECT
22uF 10uF 2200uF 100uF 2200uF
20% 20% 20% 20% 20%
50V 50V 16V 25V 35V
C353
1-126-953-11 ELECT
2200uF
20%
35V
Ref. No.
Part No.
Description
C354 C355 C356 C357
1-126-961-11 1-130-485-00 1-130-481-00 1-130-481-00
ELECT MYLAR MYLAR MYLAR
2.2uF 0.015uF 0.0068uF 0.0068uF
20% 5% 5% 5%
50V 50V 50V 50V
Remark
C358 C360 C361 C362 C370
1-130-486-00 1-126-964-11 1-126-947-11 1-126-964-11 1-107-826-11
MYLAR ELECT ELECT ELECT CERAMIC CHIP
0.018uF 10uF 47uF 10uF 0.1uF
5% 20% 20% 20% 10%
50V 50V 35V 50V 16V
< CONNECTOR > CN302 CN303 CN305 CN309 CNB307
1-784-780-11 1-691-040-31 1-784-778-11 1-564-506-11 1-564-509-11
CONNECTOR, FFC 19P CONNECTOR, FFC 8P CONNECTOR, FFC 17P PLUG, CONNECTOR 3P PLUG, CONNECTOR 6P
* CNB308 1-564-512-11 PLUG, CONNECTOR 9P < DIODE > D301 D302 D303 D304 D305
8-719-991-33 8-719-991-33 8-719-109-72 8-719-109-72 8-719-983-20
DIODE DIODE DIODE DIODE DIODE
1SS133T-77 1SS133T-77 RD3.9ESB2 RD3.9ESB2 MTZJ-T-77-4.3C
D306 D307 D308 D310 D317
8-719-983-20 8-719-991-33 8-719-991-33 8-719-983-20 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
MTZJ-T-77-4.3C 1SS133T-77 1SS133T-77 MTZJ-T-77-4.3C 1SS133T-77
D318 D321 D322
8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 < FERRITE BEAD >
FB301 FB302 FB317
1-412-473-21 INDUCTOR (SMALL TYPE) 1-412-473-21 INDUCTOR (SMALL TYPE) 1-500-445-21 FERRITE, EMI (SMD) (2012) < IC >
IC302
6-702-895-01 IC BD3881FV < JACK >
J302 J303
1-536-708-81 TERMINAL BOARD, PUSH (4P) (SPEAKER IMPEDANCE USE 8-16Ω) 1-778-940-11 JACK 2P (MD) < CAPACITOR/COIL >
40
JW120 JW323
1-107-826-11 CERAMIC CHIP 1-410-509-11 INDUCTOR
0.1uF 10uH
10%
< COIL > L101 L201
1-422-009-13 COIL, AIR-CORE 1-422-009-13 COIL, AIR-CORE < TRANSISTOR >
Q311 Q312
8-729-037-13 TRANSISTOR 8-729-036-86 TRANSISTOR
KTA1271Y KTC3203Y-AT
16V
HCD-NE3 MAIN Ref. No.
Part No.
Description
Remark
Q313 Q314 Q315
8-729-036-86 TRANSISTOR 8-729-037-13 TRANSISTOR 8-729-054-16 TRANSISTOR
KTC3203Y-AT KTA1271Y KRC402-RTK
Q317 Q319 Q320 Q326 Q327
8-729-028-54 8-729-040-76 8-729-054-16 8-729-034-50 8-729-034-50
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
KTC3205 KTA1273-Y-AT KRC402-RTK KTA1504 KTA1504
Q328 Q329 Q330 Q331 Q332
8-729-045-62 8-729-045-62 8-729-045-62 8-729-054-03 8-729-054-03
FET FET FET TRANSISTOR TRANSISTOR
2SK2158-T2B 2SK2158-T2B 2SK2158-T2B KRA303-RTK KRA303-RTK
Q333 Q338 Q339 Q342 Q343
8-729-054-16 8-729-054-16 8-729-036-86 8-729-120-28 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
KRC402-RTK KRC402-RTK KTC3203Y-AT 2SC1623-L5L6 2SC1623-L5L6
Q344 Q345 Q346 Q347 Q348
8-729-142-46 8-729-142-46 8-729-801-93 8-729-037-03 8-729-036-58
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC2001-LK 2SC2001-LK 2SD1387-3 KTA1266GR-AT KRC102M-AT
< RESISTOR > R100 R101 R102 R103 R104
1-216-812-11 1-216-834-11 1-216-840-11 1-216-817-11 1-216-805-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
180 12K 39K 470 47
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R105 R106 R107 R108 R109
1-216-852-11 1-216-830-11 1-216-847-11 1-216-835-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
390K 5.6K 150K 15K 2.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R111 R112 R113 R114 R115
1-216-825-11 1-216-839-11 1-216-817-11 1-216-818-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 33K 470 560 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R116 R117 R118 R119 R120
1-216-832-11 1-216-825-11 1-218-867-11 1-216-824-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
8.2K 2.2K 6.8K 1.8K 10K
5% 5% 0.5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R121 R122 R123 R124 R125
1-216-825-11 1-216-843-11 1-216-825-11 1-216-835-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 68K 2.2K 15K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R126 R128 R131 R132 R136
1-216-837-11 1-216-822-11 1-216-822-11 1-216-821-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 1.2K 1.2K 1K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R137 R143 R200
1-216-829-11 METAL CHIP 1-216-832-11 METAL CHIP 1-216-812-11 METAL CHIP
4.7K 8.2K 180
5% 5% 5%
1/10W 1/10W 1/10W
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
Remark
R201 R202
1-216-834-11 METAL CHIP 1-216-840-11 METAL CHIP
12K 39K
5% 5%
1/10W 1/10W
R203 R204 R205 R206 R207
1-216-817-11 1-216-805-11 1-216-852-11 1-216-830-11 1-216-847-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 47 390K 5.6K 150K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R208 R209 R211 R212 R213
1-216-835-11 1-216-825-11 1-216-825-11 1-216-839-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
15K 2.2K 2.2K 33K 470
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R214 R215 R216 R217 R218
1-216-818-11 1-216-827-11 1-216-832-11 1-216-825-11 1-218-867-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
560 3.3K 8.2K 2.2K 6.8K
5% 5% 5% 5% 0.5%
1/10W 1/10W 1/10W 1/10W 1/10W
R219 R220 R221 R222 R223
1-216-824-11 1-216-833-11 1-216-825-11 1-216-843-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.8K 10K 2.2K 68K 2.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R224 R225 R226 R228 R231
1-216-835-11 1-216-837-11 1-216-837-11 1-216-822-11 1-216-822-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
15K 22K 22K 1.2K 1.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R232 R236 R237 R243 R301
1-216-821-11 1-216-833-11 1-216-829-11 1-216-832-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 10K 4.7K 8.2K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R302 R303 R304 R305 R315
1-216-835-11 1-216-833-11 1-216-821-11 1-216-809-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
15K 10K 1K 100 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R317 R318 R319 R320 R321
1-216-841-11 1-216-817-11 1-216-857-11 1-216-829-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 470 1M 4.7K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R322 R323 R324 R325 R326
1-216-823-11 1-216-821-11 1-216-825-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.5K 1K 2.2K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R327 R332 R336 R348 R349
1-216-833-11 1-216-821-11 1-216-829-11 1-216-821-11 1-216-842-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 1K 4.7K 1K 56K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R350 R351 R352 0 R353 R358
1-216-833-11 1-216-833-11 1-249-413-11 1-212-958-00 1-216-842-11
METAL CHIP METAL CHIP CARBON FUSIBLE METAL CHIP
10K 10K 470 10 56K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/2W F 1/10W
41
HCD-NE3 MAIN
POWER
REG
Ref. No.
Part No.
Description
Part No.
Description
R359 0 R360 0 R361 R362 R363
1-260-330-11 1-219-787-17 1-219-787-17 1-216-836-11 1-216-836-11
CARBON FUSIBLE FUSIBLE METAL CHIP METAL CHIP
1.5K 5.6 5.6 18K 18K
5% 5% 5% 5% 5%
1/2W 1/4W F 1/4W F 1/10W 1/10W
D911 D912 D913 D914 D916
8-719-063-79 8-719-063-79 8-719-063-79 8-719-063-79 8-719-046-47
DIODE DIODE DIODE DIODE DIODE
1N4002B 1N4002B 1N4002B 1N4002B 1N5401TM
R364 R365 R366 R367 R368
1-218-867-11 1-216-825-11 1-216-837-11 1-216-825-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
6.8K 2.2K 22K 2.2K 10K
0.5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
D917 D918 D919 D920 D921
8-719-046-47 8-719-046-47 8-719-046-47 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
1N5401TM 1N5401TM 1N5401TM 1SS133T-77 1SS133T-77
R370 R371 R372 R373
1-216-833-11 1-216-833-11 1-216-844-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 82K 10K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
D922 D923 D924
8-719-050-84 DIODE RB441Q-40T-77 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77
Remark
Ref. No.
Remark
< LINE FILTER > < TRANSFORMER > 0 LF901 T301 1-423-980-11 TRANSFORMER, BIAS OSCILLATION ************************************************************ A-1055-614-A A-1056-003-A A-1056-266-A A-1056-495-A A-1056-526-A
POWER BOARD, COMPLETE (E, E51, SP) POWER BOARD, COMPLETE (AR, AUS) POWER BOARD, COMPLETE (MX, TW) POWER BOARD, COMPLETE (EA) POWER BOARD, COMPLETE (KR)
A-4750-273-A POWER BOARD, COMPLETE (AEP, UK) A-4751-335-A POWER BOARD, COMPLETE (US, CND) ***********************
1-402-663-11 TRANSFORMER, LINE FILTER (LFT) < RESISTOR >
R901 R902 0 R903
1-249-437-11 CARBON 1-249-437-11 CARBON 1-219-237-51 CARBON
47K 47K 3.3M
5% 5% 5%
R904 R905
1-249-421-11 CARBON 1-249-421-11 CARBON
2.2K 2.2K
5% 5%
R906
1-249-417-11 CARBON
1K
R906
1-249-418-11 CARBON
R910
1-219-120-11 FUSIBLE
5% 1/4W (US, CND, AEP, UK, KR) 1.2K 5% 1/4W (EXCEPT US, CND, AEP, UK, KR) 0.15 5% 1/4W
< CAPACITOR > C901 C902 C903 C905 C906
1-136-165-00 1-136-165-00 1-136-165-00 1-161-055-00 1-161-055-00
FILM FILM FILM CERAMIC CERAMIC
0.1uF 0.1uF 0.1uF 0.022uF 0.022uF
5% 5% 5% 10% 10%
50V 50V 50V 50V 50V
C907 C908 C909 C910 C911
1-161-055-00 1-161-055-00 1-161-055-00 1-161-055-00 1-161-055-00
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
0.022uF 0.022uF 0.022uF 0.022uF 0.022uF
10% 10% 10% 10% 10%
50V 50V 50V 50V 50V
C912 0 C913 C914 C915
1-161-055-00 1-113-925-11 1-126-947-11 1-136-497-81
CERAMIC CERAMIC ELECT FILM
0.022uF 0.01uF 47uF 0.1uF
1/4W 1/4W 1/2W F (US, CND) 1/4W 1/4W
< RELAY > 0 RY901
1-755-276-11 RELAY, POWER < SWITCH >
0 S901
1-571-309-11 SWITCH (VOLTAGE DETECT) (E, E51, EA, SP) < TRANSFORMER >
0 T901
C915
1-136-165-00 FILM
10% 50V 20% 250V 20% 35V 5% 50V (EA, MX, TW) 0.1uF 5% 50V (EXCEPT EA, MX, TW)
1-439-772-11 TRANSFORMER, POWER (EXCEPT US, CND, AEP, UK, KR) 0 T901 1-439-779-11 TRANSFORMER, POWER (AEP, UK, KR) 0 T901 1-439-781-11 TRANSFORMER, POWER (US, CND) ************************************************************ REG BOARD ********* < CAPACITOR >
< CONNECTOR > * CN901 * CN902 * CN902
1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P 1-564-511-11 PLUG, CONNECTOR 8P (EXCEPT EA, MX, TW, KR) 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P (EA, MX, TW, KR) < DIODE >
D906 D907 D908 D909 D910
42
8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33
DIODE DIODE DIODE DIODE DIODE
C306 C307
1-164-156-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP
0.1uF 0.1uF
25V 25V
< IC > IC305 8-759-231-57 IC TA7810S IC306 8-759-450-49 IC BA07T ************************************************************
1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
HCD-NE3
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
MISCELLANEOUS ************** 05 05 05 05 05
1-696-570-21 1-775-790-12 1-769-079-23 1-769-744-52 1-783-531-22
CORD, POWER (EA) CORD, POWER (AUS) CORD, POWER (KR) CORD, POWER (AEP, UK, E51, SP) CORD, POWER (US, CND)
05 05 05 6 6
1-829-387-11 1-827-226-11 1-827-597-31 1-693-625-11 1-693-628-11
CORD, POWER (AR) CORD, POWER (E, MX) CORD, POWER (TW) TUNER (FM/AM) (US, CND) TUNER (FM/AM) (E, E51, EA, MX, SP, TW, AR, AUS)
6 10 110 163 0 167
1-693-629-11 1-500-386-11 1-796-352-41 1-827-991-11 8-820-221-01
TUNER (FM/AM) (AEP, UK, KR) FILTER, CLAMP (FERRITE CORE) DECK, MECHANICAL (CMAL5Z220A) WIRE (FLAT TYPE) (16 CORE) OPTICAL PICK-UP KSM-213EDP/C2NP
0 T902 0 T902 0 T902 0 T902 0 T902
1-443-245-11 1-443-244-11 1-443-396-11 1-443-397-11 1-443-246-11
TRANSFORMER, POWER (AEP, UK) TRANSFORMER, POWER (US, CND) TRANSFORMER, POWER (EA) TRANSFORMER, POWER (KR) TRANSFORMER, POWER (E, E51, SP, TW, AR, AUS)
S101 S820
1-771-853-11 SWITCH, DETECTION (LIMIT) 1-692-960-11 SWITCH, PUSH (1KEY) (CD LID OPEN/CLOSE DETECT) ************************************************************ ACCESSORIES ************ 0 0
1-569-008-32 ADAPTOR, CONVERSION (E51, SP) 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
43
HCD-NE3
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0
Date 2004.03
Description of Revision New
