Transcript
ST-S5 SERVICE MANUAL
AEP Model UK Model E Model Australian Model
Ver 1.0 2001.04
ST-S5 is the tuner section in MHC-S7AV.
SPECIFICATIONS Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section
Tuning range Antenna Antenna terminals Intermediate frequency
87.5 – 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz
AM tuner section
Tuning range AEP, UK models: Other models:
Antenna Antenna terminals Intermediate frequency Dimensions (w/h/d) Mass
531 – 1,602 kHz (with the interval set at 9 kHz) 531 – 1,602 kHz (with the interval set at 9 kHz) 530 – 1,710 kHz (with the interval set at 10 kHz) AM loop antenna External antenna terminal 450 kHz Approx. 280 x 108 x 340 mm Approx. 2.1 kg
Design and specifications are subject to change without notice.
FM STEREO/FM-AM SUPERHETERODYNE TUNER 9-873-832-11
Sony Corporation
2001D0500-1 C 2001.4
Home Audio Company Shinagawa Tec Service Manual Production Group
ST-S5
TABLE OF CONTENTS 1.
SERVICING NOTES ................................................ 3
2.
GENERAL Location of Controls ....................................................... 4 Setting the Time .............................................................. 5
3.
DISASSEMBLY
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
Disassembly Flow ........................................................... Cover ............................................................................... Front Panel Section ......................................................... PANEL Board, SIRCS Board ......................................... Tuner pack (FM/AM) ...................................................... MAIN Board ................................................................... DSP Board .......................................................................
4.
TEST MODE .............................................................. 10
5.
DIAGRAMS
5-1. Note for Printed Wiring Boards and Schematic Diagrams ....................................................... 5-2. Schematic Diagram – MAIN Board (1/2) – .................. 5-3. Schematic Diagram – MAIN Board (2/2) – .................. 5-4. Printed Wiring Board – MAIN Board – ........................ 5-5. Printed Wiring Board – DSP Board – ............................ 5-6. Schematic Diagram – DSP Board (1/2) – ..................... 5-7. Schematic Diagram – DSP Board (2/2) – ..................... 5-8. Printed Wiring Boards – PANEL Section – .................. 5-9. Schematic Diagram – PANEL Section – ....................... 5-10. IC Pin Function Description ...........................................
6.
6 7 7 8 8 9 9
11 12 13 14 15 16 17 18 19 21
EXPLODED VIEWS
6-1. Cover, Front Panel Section ............................................. 28 6-2. Chassis Section ............................................................... 29
7.
2
ELECTRICAL PARTS LIST ............................... 30
Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ST-S5 SECTION 1 SERVICING NOTES This set is a component of the MHC-S7AV. The MHC-S7AV system configuration is as shown below, and therefore it does not operate normally unless all four components are connected. In performing the repair, connect all components with the system cables. Note: The precaution to the users is described on the label stuck on the back panel (CD player) and in the troubleshooting section in the Operation Manual.
• MODEL IDENTIFICATION – Rear Panel –
System Configuration:
TA POWER SUPPLY
PART No.
AC IN
MODEL
PART No.
AEP and UK models
4-232-327-0[]
Australian model
4-232-327-1[]
Mexican model
4-232-327-4[]
Korean model
4-232-327-9[]
ST SYSTEM & CD µcon DISPLAY
CDP TC TC µcon
3
ST-S5 SECTION 2 GENERAL
This section is extracted from instruction manual.
LOCATION OF CONTROLS – Front Panel –
qh
wh
qjqk ql w;
wg wf
–
+
–
+
wd ws wa
CLOCK/TIMER wg (13, 21, 29) DISPLAY qh (13, 16, 18, 29, 35) ENTER w; (17, 18) IR receptor wh PRESET +/– ws (17, 18) PTY (AEP, UK models only) wa (18) STEREO/MONO qj (17) TIMER SELECT wf (22, 30) TUNER/BAND wd (17) TUNER MEMORY qk (17) TUNING +/– ql (17)
– Rear Panel –
1
1 ANTENNA terminal 2 SYSTEM CONTROL 1 connector (TO TA-S7AV) 3 SYSTEM CONTROL 2 connector (TO TA-S7AV) 4 SYSTEM CONTROL 3 connector (FROM CDP-S3) 5 OPTICAL IN terminal
2
6 OPTICAL IN terminal (FROM CDP-S3)
3
7 SYSTEM CONTROL 4 connector (TO TC-S3) 8 OPTICAL OUT terminal 9 SUB WOOFER OUT jack
4
5 6 7 8 9 0 qa
0 MD IN/OUT jack qa VIDEO (AUDIO) IN jack
4
ST-S5
Setting the time
Remote Control
1 2
1 2 3
Turn on the system. Press CLOCK/TIMER (or CLOCK/TIMER SET on the remote).
When you set the time for the first time, proceed to step 5. es ea e; wl wk wj wh wg
H hH hH
.
>
x
m
M
X
O P
p
4 5 6 7 8 9 q; qa
o
wf wd ws wa w; ql qk
CD H es (14, 15) CHECK 5 (15) CLEAR 6 (15) CLOCK/TIMER SELECT qj (30) CLOCK/TIMER SET qk (13, 21, 29) DBFB qg (23) DISPLAY ws (13, 16, 18, 29, 35) D.SKIP 4 (14) ENTER wg (10, 12, 13, 15, 17, 18, 21, 22, 26–30) EQ qd (27) EQ ON/OFF qf (10, 28) FUNCTION wf (10, 14, 15, 20, 21, 31) GROOVE wa (23) SET UP qs (10, 12, 26, 28, 29) SLEEP 7 (29) SUR wd (25) TAPE A hH ea (19, 35) TAPE B hH e; (19, 20, 35)
qs qd qf qg
3
Press O or o repeatedly to select “CLOCK SET”.
4 5 6 7
Press ENTER (A/V amplifier or remote).
8
Press ENTER (A/V amplifier or remote).
Press O or o repeatedly to set the hour. Press ENTER (A/V amplifier or remote). Press O or o repeatedly to set the minutes.
Tip
If you have made a mistake or want to change the time, start over from step 2.
qh
Note
qj
The clock settings are canceled when you disconnect the power cord or if a power failure occurs.
TUNER/BAND wl (17) TUNING + 9 (17) TUNING – wh (17) TV CH +/– ql TV VOL +/– w; TV @/1 2 TV/VIDEO 1 VOL +/– qh BUTTON DESCRIPTIONS @/1 (power) 3 X (pause) q; x (stop) 8 . (go back) wk > (go forward) wj m (rewind) wh M (fast forward) 9 O/o/P/p qa
5
ST-S5 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. COVER (Page 7)
6
3-3. FRONT PANEL SECTION (Page 7)
3-5. TUNER PACK (FM/AM) (Page 8)
3-4. PANEL BOARD, SIRCS BOARD (Page 8)
3-6. MAIN BOARD (Page 9)
3-7. DSP BOARD (Page 9)
ST-S5
Note: Follow the disassembly procedure in the numerical order given.
3-2.
COVER 3 cover 1 screw (+BVTT3 × 6 (S))
2 two screws (case 3 TP2)
2 two screws (case 3 TP2)
3-3.
FRONT PANEL SECTION
1 wire (flat type) (19 core) (CN502)
3 two claws 4 front panel section
3 two claws 3 claw
2 three screws (BVTP3 × 8)
7
ST-S5
3-4.
PANEL BOARD, SIRCS BOARD
2 two screws (BVTP2.6 × 8) 6 SIRCS board 4 PANEL board 2 four screws (BVTP2.6 × 8)
5 two claws
2 screw (BVTP2.6 × 8) (AEP, UK models)
1 wire (flat type) (19 core) (CN602)
3 two claws
3-5.
TUNER PACK (FM/AM)
3 tuner pack (FM/AM)
1 wire (flat type) (11 core) (Korean, Mexican and Australian models) wire (flat type) (15 core) (AEP, UK models) (CN506)
2 two screws (BVTP3 × 8)
8
ST-S5
3-6.
MAIN BOARD
1 wire (flat type) (21 core) (CN509)
2 five connectors (CN510, 5031, 5032, 5041, 5042)
1 wire (flat type) (23 core) (CN508)
6 MAIN board 4 screw (BVTP3 × 8)
4 two screws (BVTP3 × 8)
1 wire (flat type) (19 core) (CN502) 3 three screws (BVTP3 × 8)
5 PC board holder 2 connector (CN601)
3-7.
DSP BOARD
1 wire (flat type) (23 core) (CN603) 4 three screws (BVTP3 × 8)
6 DSP board
1 wire (flat type) (21 core) (CN602)
3 three screws (BVTP3 × 8)
5 PC board holder
2 connector (CN601)
9
ST-S5 SECTION 4 TEST MODE Note: Use flowing buttons in the test mode. no mark : Button of tuner unit (ST-S5) *1 : Button of amplifier unit (TA-S7AV) *2 : Button of CD unit (CDP-S3)
[MC Cold Reset] • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the [DIGITAL] * 1 button, press the [DISPLAY] button. 3. The set is reset, and becomes standby state. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the M *2 button. 3. The set is reset, and becomes standby state. [MC Hot Reset] • This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged in and out. Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [TIMER SELECT] button. 3. The set is reset, and becomes standby state. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the m *2 button. 3. The set is reset, and becomes standby state. [Change-over the AM Tuning Interval] (EXCEPT AEP and UK models) • The AM tuning interval can be changed over 9 kHz or 10 kHz. Procedure: 1. Press the ?/1 *1 button to turn the power ON. 2. Turn the [FUNCTION] *1 knob to select “TUNER”, and press the [TUNER/BAND] button to select the BAND “AM”. 3. Press the ?/1 *1 button to turn the power OFF. 4. While pressing the [ENTER] button, press the ?/1 *1 button, and the display on the fluorescent indicator tube changes to “AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning interval is changed over. [Change-over of VACS ON/OFF] 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [CINEMA STUDIO B] button, and VACS ON/OFF is change over.
10
[GC Test Mode] Enter the GC Test Mode mode Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [CLOCK/TIMER] button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the Z (DISC 1)*2 button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Version Display Mode Procedure: 1. Enter the GC test mode. 2. Each time the [TUNER MEMORY] or [DISC 1]*2 button is pressed, microcomputer or mechanism deck version is displayed of each unit. 3. Press the [TUNING +] or [DISC 3]*2 button to detail is displayed the version. Key Check Mode Procedure: 1. Enter the GC test mode. 2. Press the [TUNING -- ] or [DISC 2]*2 button to set the key check mode. 3. In the key check the mode, the fluorescent indicator tube displays “K 0 J 0 V 0” . Each time a button is pressed, “K” value increases. However, once a button is pressed, it is no longer taken into account. VACS Level Display Mode Procedure: 1. Enter the GC test mode. 2. Press the [TUNING +] or [DISC 3]*2 button to display VACS level on the fluorescent indicator tube. Segment Check Mode Procedure: 1. Enter the GC test mode. 2. Press the [ENTER] or x *2 button to set the segment check mode. 3. In the segment check the mode. Each [ENTER] or x *2 button is pressed, the fluorescent indicator tube displays is switching variously. Releasing the GC Test Mode • To release from this mode, press three buttons in the same manner as entering this mode or disconnect the power cord.
ST-S5 SECTION 5 DIAGRAMS 5-1.
• Circuit Boards Location
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
• Indication of transistor.
C Q
These are omitted.
B E
Q B C
E These are omitted.
Q B
C
E These are omitted.
Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f : internal component. • • 5 : fusible resistor. • C : panel designation.
DSP board
TUNER PACK
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • A : B+ Line. • B : B– Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : TUNER (FM/AM) ( ) : CD PLAY 〈〈 〉〉 : AC OFF : Impossible to measure ∗ • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Signal path. F : TUNER (FM/AM) E : TAPE PLAY G : RECORD J : CD PLAY c : DIGITAL INPUT N : MIC INPUT • Abbreviation AUS : Australian model KR : Korean model MX : Mexican model
SIRCS board MAIN board
PANEL board
11
11
ST-S5 SCHEMATIC DIAGRAM – MAIN Board (1/2) –
(1/2) CN5031 5P M(A)-GND EVER+5V NO901 3P
D-GND
NO991 3P
D+5V
C991 0.1
I G
(Page 13) CN5041 10P
+15V REGULATOR O
C992 0.1
IC991 NJM7815FA
AA6
MIC-SIG MIC-GND
(A-GND)
AA5
FL-OUT FRONT-GND AA4 FR-OUT AA3 CENTER-OUT CENTER-GND AA2
(Page 13)
SL-OUT S-GND AA1 1
SR-OUT
2 3 4
OPTICAL RECEIVER VCC C955 10000p
OPTICAL IN (FROM CDP-S3)
5
GND
6 R951 470
OUT IC951 TORX178B
C957 10000p
OPTICAL RECEIVER VCC OPTICAL IN GND
OUT IC952 TORX178B
R952 470
L951 220µH
7 8 9
C964 10000p
C956 10 50V
AB21
NO507 4P
AB20
(CHASSIS)
C916 10000p
10
(Page 16)
CN510 5P REC OUT-R
BB1 BB2
PB-R TC A-GND
BB3
PB-L BB4 REC OUT-L
SYSTEM CONTROL 4 CN508 23P
(TO TC-S3)
C977 10 50V
+10V REGULATOR DD1
IC903 NJM7810FA
L955 470µH
TUNER L-IN DD2
O
11
I G
VCD L-IN BB3 TC L-IN BB4 TC REC L-OUT A-GND BB1
D941 1SS133T
R941 1k
D942 1SS133T
R942 1k
TC REC R-OUT BB2 TC R-IN DD3 VCD R5-IN C978 10 50V
D901 D3SBA20
DD4
TUNER R-IN C966 10000p
A+10V AA6
C905 470 16V
C904 3300 16V
C952 4700 25V
C953 0.1
(Page 13)
C941 10 50V
R943 3.3k
MIC-IN A-GND AA5 FL-OUT
(Page 17)
F-GND AA4 FR-OUT
+5V REGULATOR
A-GND
IC904 µPC7805AHF
AA2 LS-OUT
DBFB FEEDBACK
5-2.
S-GND AA1 RS-OUT C-GND AA3 C-OUT LINE-MUTE
O
I
D922 11ES2
G
D903 11ES2
C907 220 10V
C906 0.1 D904 11ES2
DBFB FEEDBACK D923 11ES2 CN509 21P D-GND
+7V REGULATOR IC901 TA78057S
D-OUT D920 11ES2-NTA2
D-GND E8
O
DSP-DECODE
R551 470
I
D551 1SS133T-72
R555 4.7k
R552 10k
G E7
DSP-CS E9 12
AMP-DATA C902 470 10V
E6 DSP-ACK
E10
AMP-CLK E5 CODEC-SMUTE E11 AMP-LAT
Q902 2SC2001-K1K2
RESET SIGNAL
+3.3V REGULATOR
IC551 M51943BSL
GENERATOR
E4
C553 0.1
DIR-Rx E12
I
DIG-Tx
(Page 16)
O
R554 47k
G E3
Q551 2SC2603
DIR-XSTATE E13 DSP-Rx
R911 220
E2
RESET SWITCH
DIR-CS E14 DIG-CLK E1
DIR-UNLOCK
C971 10000p
D-GND D+5V C968 10000p A-GND A+5V
R912 510
C970 10000p
C903 10 50V
C918 470 10V
C551 10 50V
C552 0.1
R553 47k
D552 1SS133T 13
14 15 16 17
12
12
ST-S5 5-3.
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
• See page 20 for Waveforms.
(2/2) CN506 15P (AEP,UK) ST-CLK
11P (E,AUS) CL R957 100
(AEP,UK)
ST-DIN
MC D0 ST-DOUT MC D1 ST-CE
COAXIAL CE
FM 75Ω
A+10V R958 100
TUN
R959 100
STE
TUNED FM/AM
FM
C962 10 50V
C961 0.1
R961 2.2k
TUNER
75Ω
R964 5.6k
DD1
L-CH
UNIT ANALOG-GND
*
R962 2.2k
(E,AUS)
CN505 17P
DD4 DD2
R-CH ST-MUTE
R963 5.6k
MUTE
VCD L-IN
AM
CD A-GND DD3
D+5V
VCD R-IN
D902 11ES2-NTA2
N.C RDS-INT
HAKO-GND
RDS-INT RDS-DATA
TC M-GND
(AEP,UK)
RDS-DATA
TC M-GND JW95
(AEP,UK)
* SUPPLIED WITH THE ASSEMBLED
1
BLOCK
2
UNREG TC D-GND I-CLK
R965 100
I-DAT
R966 100
SYSTEM CONTROL 3
I2C-CLK
(FROM CDP-S3)
3
I2C-DATA
4
V-MUTE M-RESET
5
MRESET
6
EVER+5V CD D(M)-GND D912 MTZJ-T72-30B
C910 10 50V
R904 10k
R903 10
D911 11ES2 -NTA2
D913 MTZJ-T-72-5.6B
R908 1k
R905 100
Q901 2SB734-3
C937 0.1
R906 100
CD D(M)-GND
D921 1SS133T-72
C915 100 35V
C909 100 50V
AB1 AC-LOW AB2 AC-LOW
CN502 19P DISPLAY/STANDBY KEY
-28V REGULATOR
VF VF -VP D-GND
7 JOG2-B 8
JOG2-B JOG2-A
9
JOG2-A POWER KEY
JOG1-B JOG1-B JOG1-A JOG1-A VOLA
D943 1SS133T
R549 3.3k
VOLA VOLB
10
VOLB C506 4.7 50V
M-RESET R558 1M
R550 100k
D944 1SS133T
RESET
Q502 BN1A4M
I-DAT
MUTING
I-CLK IIC-CLK KEY1
R524 47k
SWITCH
KEY1
Q503 BN1A4M
D+3.3V D-GND
AC OFF MUTING
C510 4.7 50V
D945 1SS133T
R557 22k
C942 470 6.3V
DRIVER
EVER+5V(SIRCS)
C943 0.1
SIRCS SIRCS
R530 100
EX-IN
EX-LAT
EX-OUT
R527 100
R528 100
R556 47k
DBFB FEEDBACK
SYSTEM CONTROL 2
CN5042 9P
(TO TA-S7AV) DBFB FEEDBACK HAKO-GND
POWER KEY C561 0.1
R526 100
R531 100
R533 100 E1
R534 100 E2
R535 100 E3
R536 100 E4
R537 100 E5
E6
EX-CLK
R532 47k
11
R538 100
(Page 19)
IIC-DATA
CONTROL
EPT901
POWER KEY EX-CLK EXP-CLK EX-LAT EXP-LAT EX-OUT
R956 100
EXP-OUT DATA EX-IN EXP-IN DATA KEY1
(Page 12)
UNREG
NO-USE
EXP-IN DATA
VCC
EXP-LAT
EXP-CLK
SOFT-TEST
VSS
LINE-MUTE
EXP-OUT DATA
R540 100
DISPLAY KEY
POWER KEY
DSP-DECODE
DIR-UNLOCK
E8
DIR-CS
DIR-XSTATE
DSP-CS
DIR-RX
E7
-SMUTE
CODEC
KEY0 TA DSP-ACK R539 100
(CHASSIS)
CN5032 15P
JOG2-B
(Page 12)
JOG2-B(F-SELECT) JOG2-A JOG2-A(F-SELECT)
SYSTEM CONTROL 1
JOG1-B JOG1-A JOG1-A(FUNCTION)
STE
R523 100
STEREO TUN
R542 47k
VOLA VOLA M-RESET
VOLB
TUNED
VOLB AB20
R522 10k R544 4.7k
AC HIGH AB21
M-RESET
R543 150
* R545
MODEL-IN
10k (AEP,UK)
AC HIGH C972 0.1
AB2
C562 10000p
SYSTEM CONTROLLER
AC LOW AB1
IC501 M30622MGA-A39FP
AC LOW
SPEC-IN
4.7k (KR,AUS) R546 *
1k (MX) * R546
(E,AUS)
150 (KR,AUS)
(TO TA-S7AV)
JOG1-B(FUNCTION)
R541 47k
VP
R545 *
VF V-MUTE
VF
AVSS
CT CC2
4.7k (MX)
NO-USE
(Page 12)
CT CC3
C508 10 50V
VREF
NO-USE
AVCC
NO-USE
EPT902
IIC CLK
ST-DIN
ST-CLK
CC1
ST-DOUT
ST-CE
ST-MUTE
RDS-DATA
RDS-INT
NMI
VCC
XOUT
XIN
VSS
XCIN
RESET
XCOUT
CNVSS
GND
DIG-CLK
DSP-RX
DIG-TX
C509 0.1
SIRCS
CUT
R548 4.7k
AMP-LAT
AC-
12
AMP-CLK
AMP-DATA
CC4 C928 0.1
NO-USE
C927 0.1
(CHASSIS)
IIC DATA CN503 10P GND CC1 TXD1/CAN'T USE CC2
R514 100
R513 100
R512 100
(E,AUS)
R516 100
R517 100
R518 100
R519 10k
+5V CC3
R525 100
(FOR TEST) CLK1/SQ-CLK
CC4
R520 10k
R529 100 RXD1/SQ-DATA-IN
CC5 CNVSS
I-DAT
I-CLK
ST-CLK
ST-DIN
ST-DOUT
ST-CE
ST-MUTE
CC6
RDS-DATA
C505 1000 6.3V
RDS-INT
C504 0.1
R515 1k
JW501 JW502
R511 10k
R510 330
X502 16MHz
C502 15p
C503 0.1
R508 10k
SIRCS
C501 18p
E14
E12
E13
E11
E10
X501
R501 100
RTS1 NC
R509 330k
32.768 kHz
R507 100
R505 100
R506 100
R504 100
R502 100
R503 100
C519 100p
E9
ANTENNA
STEREO
R521 100 RESET
C520 100p
GND
CN501 4P
13
D-GND D+5V (FOR TEST)
I-CLK IIC-CLK
14 CC5
CC6
I-DAT IIC-DATA
15 16 17
(CHASSIS)
13
13
ST-S5 PRINTED WIRING BOARD – MAIN Board –
• Semiconductor Location
2
3
5
6
7
8
Location
AM
COAXIAL FM 75Ω
SYSTEM CONTROL 1 (TO TA-S7AV)
* SUPPLIED WITH THE ASSEMBLED BLOCK
FM/AM TUNER UNIT *
MAIN BOARD
(CHASSIS)
R524
R523
EPT902
EPT901
JW47
R512
R514
R537
(E, AUS)
R906
JW502 R517
JW501
R538 R511 R539 R540
JW39
C505
C504 JW32
R518
R908
D913
R519
4 CN501 (FOR TEST) C552 D551 1
C928
E
X501
R546 (E, AUS)
JW27
C501 JW503
JW21
JW19
R548
JW55
D944 E
R558
R504
JW115
R506
JW84 1
D903
JW119
IC903
R549
Q502
JW106
D921
JW81
SYSTEM CONTROL 3
JW100
D943 C506
JW94
D945
R557
E
JW90
10
3
C942 E
R965 1
JW113
JW96
R502
R555
JW26
C510
JW87
D901
1
R554
D552
R553
5
D922
C553
Q551
JW29 C508
JW88 JW107
D923
R552
JW30
1
CN5031
R904
R551 C551
JW80
JW920
C509 R544
IC551
R966
R941
JW958
CN5041
C962
C904
C905
D904
JW83
R545
C503
R963
C953
C520
3
R521
X502 R510 R509 C502 R508
R964
JW959
15
R543
R942
D942
C937
C910 D912 C915
R905
R520
4
D941
C927
C519
1
JW38
C972
(TO TA-S7AV)
9
R961
R943
D911
R903
SYSTEM CONTROL 2
JW98
JW44
R516
B
JW118
IC501
R962
JW92
R535 R536
C
CN506
C941
JW25
E
1
JW116
R529
JW43
JW50
R533 R534
C909
Q901
D902
JW89
R525
1
R956 (AEP, UK)
JW91
CN5032
R513
R515
C961
R959
C562
R528
C943
D
R957
CN503
R541
C
(AEP, UK)
JW53
R532
R526
R542
1
JW104
10
R522
CN5042
JW971
R531 R556
(CHASSIS)
R958
JW921
(FOR TEST)
JW34
C561
JW108
B
R527
R530
Q503
FROM CDP-S3
CN505
JW18
R507
JW65
JW16 R912
JW15
Q902
F
JW79
JW76
JW77
JW917 JW70
C902
E
JW14
JW78
IC901
JW28
CN502
C952
NO901
JW97
R505
C903
1
JW56
R503
C918
(Page 18)
3 3
JW952
R501
R550
JW37
PANEL BOARD CN602
JW13
JW17
1
D
JW35
JW68
CLP101
R911
JW71
D920
IC952
JW69
JW207 3
1
JW85 C970
JW201
JW93
CN509
IC904
C907
C968
C978
C906
JW64 C977
C971
JW75
L955
JW110
(Page 15)
DSP BOARD CN603
C992
(Page 15)
3 3
H
SYSTEM CONTROL 4 (TO TC-S3)
1
1
NO991 C991
(INCLUDED IN MAIN BOARD)
14
A
IC991
(FROM CDP-S3)
1 4
11
R951
NO507
B
14
1
IC951
3
OPTICAL IN
5 CN510
DSP BOARD CN602
L951
IC951
C955
C964
1 JW111
C966
C
1
R952 CN508
IC952
C916
JW60
JW99
JW202
JW957
JW203
JW112
JW204
G
C956
JW117
JW205
3
OPTICAL IN
JW954
JW206
C957
JW62
JW208
JW86
JW918
JW209
JW956
E-3 E-4 D-4 C-5 F-4
FM 75Ω
(AEP, UK)
JW41
C-2 D-4 E-6 D-6 G-4 G-10 F-10 H-8
10
(E, AUS)
A
JW42
IC501 IC551 IC901 IC903 IC904 IC951 IC952 IC991
9
ANTENNA
JW67
D-4 D-4 C-8 C-7 E-4 E-5 C-6 C-5 C-5 F-4 E-5 D-5 D-5 C-7 C-7 E-4 E-3 E-4
JW40
D551 D552 D901 D902 D903 D904 D911 D912 D913 D920 D921 D922 D923 D941 D942 D943 D944 D945
Q502 Q503 Q551 Q901 Q902
4
JW51
Ref. No.
1
• See page 11 for Circuit Boards Location.
JW500
5-4.
1-680-695DSP BOARD CN601
(Page 15)
(11)
ST-S5 5-5.
PRINTED WIRING BOARD – DSP Board –
1
• See page 11 for Circuit Boards Location.
2
3
4
5
6
7
8
• Semiconductor Location
9
Ref. No.
Location
J601
VIDEO (AUDIO) IN
MD
A IC609
DSP BOARD
3
(CHASSIS)
C732 R738
R734 C720 C712
C608 30 31
R640
R637 R639
R641
D
R611 R612 R613
1
12
44
R654
IC605
E
R647
R646
R765
R615
C741
R629
IC603
R664 R628
C657
C638
C636
C656
R660 R631 C653 C654 R633 R661 C701
R720
C651
R680
R655
E
C649
E Q609
FB604
R662
R727
FB605
C721
R723 E
C703
C648
C681
R715
R649
R711
E
MAIN BOARD CN508
R709
C689
C699
(Page 14)
C690 Q603 R755
D606
R776
C674
C673
R651
CN603
E
C678
Q606 R652
C675
E
C700
Q607
FB606 R778 (E, AUS)
R712 C672
R759
G
B
R777
R650
4
CN601
(Page 14)
C677
R724
C691
1
A MAIN BOARD NO507
C729 R784
R775
Q610 C680 C679
C676
C727 C728
R728
R717 JR601
C725
R768 C650 C652
Q602
R754
R663
JR603
E
R725
C682
IC607
Q604 C726
R729
C702
C683 R632
C687
C723
R719
FB607
R697 R700
C686
Q608
C647
Q612 E
FB608
R702
C685
E
C616
R659
R769
C684
IC606
R658
(E, AUS)
R721
C645
JR620
E Q605
C692
C640
R656
R642
R716
C731 JR621 C641
C639
R696
C693
R665
R630
C615
R666
C637
C655
C704 C695 R701
R699
C658
D604
R676
R771 E
C635
R772
F
Q613
D605
C708
R679 C619 R683 C620 C694 C730
R610
R620 R619
R730
C621
C742
C738 R621
C644
C642 C643
R713
C707
R675
R608
C736
R674
C623
R607
R657
D609 D607
C622
R606
IC602
C607
33 R648
R643
R644 R645
D610 D608
R707
R760 R762
34 23
C705
R731
R677
R653
22
Q611 R733
R688
R605
60
C606
R636 R635
R638
11
R604
C613
61
R623 R601
R603
C614
R681
C706 R682 E
C609
R602
R686 R685
C709
R698
12
R689
C666
R634
C662
FB602 C603 C604
R687 R684
C624
R751
C724
13
C661
C716
C633
R703
48
C602
C617 C618
R706
R752
C710
1 C664 Q601
IC601
C601
R691
R673
R758
C715
R749
C739
R618
IC604
R690
R616 R617
24
C660
D601
FB601 90
C740 1 X601
25
1
C713
R750
C665
3
91
R614
36
120
C612
C625
C626
C627 37
C628
R692
C646
R670 R671 R672
E
C714
C610
JR622
C
IC610
C659
R780
R668 R669
C711
R748 R747
C611
R667
(CHASSIS) EP603
C634
IC608 C629
R
C717
R779
C632 R678
L
C735
C630
R781 R756 R757
R
C719
1
C631
R735
L
C722
R739
R746
R
FB603
R742
R743
L
IC609
EP604
B
IN
OPTICAL OUT
(CONDUCTOR SIDE)
DSP BOARD (COMPONENT SIDE)
OUT
J602 SUB WOOFER OUT
R761
C671
R695
CN602
R770
C669 R693
C670
R773
R694
EP602
R766 R763 R767
1-680-319-
(CHASSIS)
R774
11
C668
(11)
C667
11
C733 1-680-319-
C
MAIN BOARD CN509
(Page 14)
15
15
(11)
D601 D604 D605 D607 D608 D609 D610
C-8 D-7 D-7 E-2 E-2 E-1 E-1
IC601 IC602 IC603 IC604 IC605 IC606 IC607 IC608 IC609 IC610
C-4 C-6 E-4 C-2 D-3 E-7 F-2 C-2 B-6 C-7
Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q611 Q612 Q613
C-8 F-6 F-7 E-9 D-9 G-8 G-9 E-8 F-8 F-8 C-9 E-6 D-8
ST-S5 SCHEMATIC DIAGRAM – DSP Board (1/2) –
• See page 20 for Waveforms.
• See page 20 for IC Block Diagram.
1 2
R666 100
4
E2
R665 100 E1
3
C657 1000p
C656 220 10V
C655 0.1
R664 100
CN602 21P A+5V
FB608
A-GND
R680 3.3k
FB607
DIGITAL
D+5V
FILTER,
D-GND
R630 100
F3 R629 100
R633 100 R628 100
C616 220 10V
6 IC603 TC74HCT7007AF
FB605 0
C648 220 10V
R614 100
R615 100
C649 0.1
R652 470
R651 470
R661 330 7 C652 0.1
R649 470 R650 470
D604 1SS355
C637 0.01
C638 0.01
C639 0.01
C642 0.001
C640 0.01
8
R643 330
C606 0.1
TP623 PAGE1
TP621 PAGE0
C647 220 10V
R663 470
C650 220 10V
C641 0.01
C607 0.1
C738 0.001
A1
R620 100
A2
R618 100
R616 100
R619 100
R617 100
D-OUT
+3.3V REGULATOR
N9
C1
N8
E1
FB604 0
D-GND
D-GND
JR603 0
Q602 2SC1623
DSP-CS DSP-DECODE
R660 330
R662 100
C615 0.1
B3
C654 0.01
R659 100
N7
AMP-DATA
C653 0.1
R658 100 D4
N10
C2
R657 100
TP619
R644 330
DSP-ACK
H2
N6
B2
H7
E2
AMP-CLK
H3
C3 F1
R645 330
CODEC-SMUTE
F2
R646 330
C2
B1
R656 10k
N5
E2 C3
AMP-LAT
R655 10k
C6
R647 330
DIG-Tx DIR-Rx
R632 100
C5
R648 330
C4
C4
C651 0.1
C5
DIR-XSTATE
SWITCH
N4
DSP-Rx
5
CONTROL
N3
C1
DIR-CS
JR621 0
IC606 PCM1748E/2K
MUTING LEVEL SHIFT
N2
E1
R631 100
N1
C6
DIG-CLK
(Page 12)
D/A CONVERTER
Q612 FN1F4M
DIR-UNLOCK
C636 0.01
C643 0.001 R613 100
G2
R611 100
G3
R610 100
A4 A5 R621 100
H6
R607 100
H5
R606 100
H4
R755 100
D0
A6
R605 100
H2
A7
R604 100
H1
D1
C644 0.1
9
IC605 AK4527
C635 0.1
R603 100
A9
C604 0.1
C646 0.01
SIGNAL PROCESSOR A10
R654 10k
IC601 CXD9617R
A11
R602 1k
A12
C721 220 10V
R642 100
R653 10k A/D,D/A CONVERTER
AUDIO DIGITAL
(Page 12)
(Page 17)
C645 220 10V
H3
A8
R754 100
C658 0.1
G1
C608 0.1 CN601 4P
D605 1SS355
H7
R608 100
JR622 0
G6
G4
R612 100
A3
A13 C603 0.1
C609 0.1 A14
G5
A15 TP622 PLOCK
A17 S-RAM
C736 0.1
C602 0.01
A16
C601 0.1
TP601 TDO
R640 100
R639 100
C740 0.1
R638 100
R601 100
TP605 TDI
R641 100
R635 100
R623 10k
TP604 TCK
R637 100
TP603 XTRST
R636 100
A14
A15
A16
A17
A1
A18
A13
A12
A11
C613 0.1
A10
A9
A8
A7
A6
A5
A2
A4
A3
A19
TP602 MS
TP614 BCK TP615 LRCK
IC602 IS61LV6416-15T
TP618 D2
TP616 DOUT
TP617 D3
H1
H6
H5
H4
H2
BCK
H3
TP611 Q613 FA1A4M RESET
10
SWITCH
11 R634 100 12 13 C612 0.1
C739 0.001
C742 0.001
R771 10k 14
C610 0.1
C611 0.1
FB601 0
A34
A33
A32
A31
A30
A29
A28
A27
A26
A25
A24
A23
A22
A21
A20
A19
A18
A23
A22
A21
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A20
C614 0.1
A34
5-6.
C659 220 10V +2.6V REGULATOR 15
G O IC610 NJM2391DL1-26TE1
I 16 17
EP604 C735 GND 0.1
18
(CHASSIS)
19
16
16
ST-S5 5-7.
SCHEMATIC DIAGRAM – DSP Board (2/2) –
• See page 20 for Waveforms.
• See page 20 for IC Block Diagram.
1
K3 R767 1k
K1
K2 R768 10k
K8
J3 R763 1k
R765 1k
J1 R766 1k
R769 1k
R775 10k
R773 1k
R777 10k
R774 1k
C691 0.1
J2
R778 1k
J4
R776 10k
(E,AUS) C690 220 10V
R770 1k
4
R772 1k
REGULATOR
K7
Q603 2SC1623
K9
+5V 3
K6
Q603
2
R762 1k
FB606 47 C689 100 16V
INPUT SELECT SWITCH, GRAPHIC EQUALIZER CONTROL, ELECTRICAL VOLUME IC607 M61512FP
5
R761 1k
K4
R760 1k
JR601 0
C667
10 50V
R759 1k
C668
10 50V
R758 1k
N1
C669
10 50V
N2
C670
10 50V
N3
C671
10 50V
N4
C672
10 50V
N5
C673
10 50V
C687 100 16V
N6
C674
10 50V
C686 100 16V
J5 K5 J6
N8
C676 1 50V
C728 0.1
C722 0.1
C678
N10
C692 0.1
8
C685 10 50V
R693 100
B2
R694 100
B1
R695 100
R698 470k
R703 1M
C618 0.01
D607 RB501V
M1
M2 R676 100
M3
+3.3V R681 33k
9
R692 100
C662 0.1
C660 220 10V
C666 220 10V
C664 0.1
C661 220 10V
C620 0.1
C665 0.1
D601 RD3.9SB2
R682 100
C621 0.01
C622 0.1
C680 10 50V
R706 47k
TUNER R-IN
K9
MIC-IN
R709 D606 0 0
D608 RB501V
D610 RB501V
C730 10 50V
C681 1 50V
L1
C682 1 50V
A-GND
R715 1k
L2
L3
G3
R686 100
G4
R687 100
G5
I3
TP608 SL
LS-OUT
I4
TP609 SR
RS-OUT
I5
TP610 C
(Page 12)
S-GND
R719 1k
C-OUT
DBFB FEEDBACK
I6
R721 1k
JR620 0
TP624 A.GND
MUTING I3
C702 1 50V
R723 1k
R725 1k J1
Q609 2SC3624 R724 47k
L1
MUTING I5
R727 1k
J2
R729 1k
C704 2.2 50V
R728 47k
J3
R731 4.7k
R733 1k Q611 2SC3624
R730 22k DIGITAL AUDIO
INVERTER
INTERFACE RECEIVER
IC608 SN74LVU04APWR
R671 100
E1
J5
R756 47k R757 47k
M3
C716 220p
R746 10k
C715 220p
R743 10k
J601 6P
R751 47k
L
VIDEO
R742 15k C708 10 50V
(AUDIO)
R750 12k C714 220p R739 15k
C707 10 50V
IN
R
L
R749 12k
IN
C713 220p
R R738 1k
C706 10 50V
MD
R748 100k
L
C712 470p
OUT R735 1k
R
C711 470p
J6
M2
C709 10 50V
R752 47k
MUTING
M1
R690 1M
C710 10 50V
MUTING
J4
R673 100
R691 0
10
FR-OUT
MUTING
L3
R672 100 G6
TP607 FR
C-GND
R720 47k R674 100
IC604 LC89056W-E
R667 100
I2
Q608 2SC3624
R688 100
R689 1k
FL-OUT
LINE-MUTE
C617 0.1
C624 0.1
TP606 FL
A-GND
I4 C701 1 50V
L4
I1
F-GND
C731 0.1
L4
C683 1 50V
TP612 LRCK
TP613 DATA
TP620 BCK
R685 100
A+10V
I6
I1 C700 10 50V
(CHASSIS)
TC R-IN VCD R5-IN
K8
Q610 2SC3624
G2
TC REC R-OUT
FEED BACK SWITCH
C703 1 50V
R684 100
K5
K7
L2
G1
TC REC L-OUT
Q604,605
R696 1.8k
R675 100
R683 100
C623 220 10V
TC L-IN
K4
(E,AUS)
C619 0.1
REGULATOR
K3
K6
R716 47k
R679 4.7k
FB603
VCD L-IN
R707 47k
Q605 2SC1623
R677 5.6k
Q601 2SD1387
TUNER L-IN
K2
A-GND
Q607 2SC3624
D609 RB501V
K1
DBFB CONTROL/ C695 0.1
EP602 GND CN603 23P
Q606 R713 2SC3624 1k MUTING
R712 47k
Q604 2SC1623
R701 10k
C684 10 50V
C679 0.1
R700 10k
R702 1M
R699 470k
C741 0.1
(Page 16)
C733 0.1
I2
C693 0.1
C694 0.1
FB602 0
C727 10 50V
C699 R711 10 1k 50V
10 50V
B3
C725 C726 10 0.1 50V
C724 0.1
R697 1.8k
C677 1 50V
N9
C723 10 50V
R717 1k
N7
C675 1 50V
C729
7
10 50V
6
R781 47k
R780 47k
R779 47k C631 0.01
C705 10 50V
J602 1P
R747 100k R734 1k
SUB WOOFER
D1
OUT C720 220p C717 0.1
D0
C719 0.1
C718 NO MT
C630 0.01
EP603 GND
11 X601 13.5MHz
12
(CHASSIS) C732 0.1
R678 10k
13 C625 10p
C626 10p
OPTICAL C628 0.1
TRANSCEIVER IC609 TOTX178A
14 C629 0.1
R668 100
F1
F3
C627 0.1 R669 100
C632 0.1
C633 220 10V
D.GND OPTICAL VCC
R670 100
15
D.OUT F2
E2
16 17
C634 0.1
18 19
17
17
OUT
ST-S5
5-8.
PRINTED WIRING BOARDS – PANEL Section –
1
2
• See page 20 for Circuit Boards Location.
3
4
5
6
7
8
9
10
PANEL BOARD
A
C610 JW24
R603 FL601 FLUORESCENT INDICATOR TUBE
C601 C653
C651
C655
C657
C659
C661
C649 S611
C664
JW1 C666
STEREO/MONO
R623
R624
R625 R626
S607
S608 ENTER
S609 –
R622
PRESET
S610 TUNER MEMORY
+
R636
R637
R634
R635
R632
R633
R630
R631
R628
R620
R621
R601 R602 R639
R638
C652 C663
–
TUNING
+
TUNER/BAND
R604
C658
C660
C662
JW31 JW33
C101 CLOCK/TIMER
C614
C615
JW10
IC101
JW114
C608
C607
R677
3
JW3
JW601
JW602
JW8
S604
C656
S602
D601
S605
C654
C603
C S606
R616
JW36
R605
R629
SIRCS BOARD
DISPLAY
IC601
X601
JW5
JW6
B
S601
C665
C650
JW57
JW11
R617
R618 JW4
C605
S603
1
TIMER SELECT
R607
R102
R627 R619 C606
C669
(AEP, UK) (AEP, UK)
R606
CN602
R608 JW45
S612
D
PTY
S601 – 612
D
• Semiconductor Location Location
D601
C-5
IC101 IC601
C-10 B-5
1
1
3
3 1-680-696-
MAIN BOARD CN502
(Page 14)
Ref. No.
NO101
NO601
18
18
R101
1-680-697-
11
11
(11)
(11)
ST-S5
SCHEMATIC DIAGRAM – PANEL Section –
• See page 20 for Waveform.
FL601
96
101
97
98
99
1
100
2
3
4
5
6
7
8
10
9
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
43
44
45
46
47
FLUORESCENT INDICATOR TUBE
100p
100p
100p
C657
C658
C659
100p
100p C656
C662
100p C655
100p
100p C654
C661
100p C653
100p
100p C652
C660
100p C651 1
2
3
4
5
6
7
8
9
10
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
12
C610 10 50V
R616 100k
(AEP,UK) S612
CN602 19P
PTY R627 5.6k
A23 32
S611
A24
STEREO/
33
VF VF G7
-VP 100
G7
A25
MONO
G6
G5
G4
G3
G2
G1
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
VSS FOR IO
31
A15
A16
A17
A18
A19
A20
A21
A22
VDD FOR VFT
DISP/STANDBY KEY
D-GND
A26 S610
B2
97
B3
96
B4
JOG2-A JOG1-B
G10
A27
JOG1-A
G11
A28 37
101
B5 VOLA
G12
A29 S609
98
JOG2-B
36
TUNER MEMORY
B1
G9
35
R626 3.9k
99 G8
34
38
R625 2.7k
B6 A30
G12
A31
G12
VOLB
39
+
RESET
40 A32 PRESET
S608
IIC-DATA
41
R624 2.2k
B8
DISPLAY CONTROLLER
A33
IIC-CLK B9
IC601 MB90M407PF-G-102 -BND
VSS FOR IO
43
KEY1
A34 S607
D+3.3V
44
R623 1.5k
A35
D-GND
45
ENTER
S604
X601 4MHz
XOUT
RESET
C608 0.1
C664 0.1
R603 10k
NO101 3P GND
+5V
+5V
OUT
OUT
C615 220p B8 R605 100
C101 47 16V
IC101 GP1U28X
R101 47
R102 47
REMOTE CONTROL
B9
RECEIVER
C667 0.1
19
R608 10k
R607 10k
R606 10k
R628 10k
B6
R629 1k
B7 R604 100
C614 220p
R630 10k
R631 1k B5 R632 10k
R633 1k R634 10k
B4
TP607
TP606 R635 1k B3
TP605 R637 1k
TP604
B2
R636 10k
R617 270
R638 10k
C666 47 50V
NO601 3P GND
TP608
R639 1k
C665 47 50V
TP603
C650 10000p
B1
CLOCK/TIMER
R618 470
R677 1k
DISPLAY
TIMER SELECT
S602
SIRCS
S601 C663 10000p
R619 560
EVER+5V(SIRCS)
XIN
TUNER/BAND
S603
C669 0.1
VSS FOR CPU KEY1
I2C DATA
I2C CLK
VOLB
VOLA
JOG1A
JOG1B
R602 10k
R620 820
JOG2A
MODE1
JOG2B
+
TP602
R601 10k
MODE2
R621 1k
C649 10000p
MODE0 S605
VCC FOR CPU
KEY0
VKK FOR VFT TP601
TUNING
AVCC FOR ANALOG
A38
-
AVSS FOR ANALOG
A37 47
R622 1.2k
D601 1SS133T-72
A36 46 S606
(Page 13)
B7
C601 10000p
5-9.
C668 0.1
C605 10000p
19
C603 0.1
C607 100 6.3V
C606 10 50V
ST-S5
• IC Block Diagrams – DSP Board –
1 IC601 9 (MCLK1), IC604 w; (XMCK), wa (XOUT)
IC604
5 IC601 ws (KFSIO), IC604 qd (CKOUT)
LC89056W-E VF F2 F1 F0 CSFLAG
1 IC501 qa (XCOUT)
XSEL
– DSP Board –
DI DO ERROR BPSYNC ERR9P DGND
• Waveforms – MAIN Board –
36 35 34 33 32 31
30
29 28 27 26 25
4.4 Vp-p
2.6 Vp-p 4 Vp-p
C BIT DETECT
CE 37 CL 38 XSEL 39 MODE0 40
74.1 ns
6 IC601 wk (LRCKI2), IC604 qg (LRCK) DOSEL0 44 DOSEL1 45
XMODE 48
1
2 3
4
5
DOUT DINO
DINI
DIN2
22.7 µs
3 IC601 ql (LRCKO), IC605 5 (LRCK), IC606 3 (LRCK (I))
PLL
INPUT CIRCUIT
DISEL
3.9 Vp-p
74.1 ns
62.5 ns
TIMING
CKSEL0 46 CKSEL1 47
4.6 Vp-p
2.7 Vp-p
DATA DEMODULATOR
6 7
8 9 10
11 12 AVDD AGND
2 IC601 qf (SCKOUT)
7 IC601 wl (BCKI2), IC604 qf (BCK)
IC605
AK4527 LOOP1 LOOP0/SDA/CDTI DIF1/SCL/CCLK DIF0/CSN P/SN MCLK DZF1 AVSS AVDD VREFH VCOM
4 Vp-p 3.8 Vp-p
44 43 42 41 40 39 38 37 36 35 34
354 ns
– PANEL Board –
22.7 µs 4 IC601 w; (BCKO), IC605 4 (BCK), IC606 1 (BCK (I))
1 IC601 id (XOUT)
SDOS I2C SMUTE BICK LRCK SDTI1 SDTI2 SDTI3
8 IC606 qh (MCLK (I))
3.7 Vp-p
3.5 Vp-p
3.6 Vp-p
INPUT CIRCUIT
1 2 3 4 5 6 7 8
AUDIO INTERFACE
OUTPUT CIRCUIT
SDTO 9 DAUX 10 DFS 11
FORMAT CONVERTER
DEM1 DEM0 TVDD DVDD DVSS PDN ICKS2 ICKS1 ICKS0 CAD1 CAD0
12 13 14 15 16 17 18 19 20 21 22
74.1 ns
250 ns
22 21 20 19 18 17 16 15 14 13
X’ TAL
R VIN LPF
2 IC501 qd (XOUT)
LOCK DETECT
DGND DVDD
30.5 µs
SAMPLING FREQUENCY
MICROCOMPUTER INTERFACE
MODE1 41 DGND 42 DVDD 43
88.6 ns
24 AUDIO 23 EMPHA
PA/PB DETECT
354 ns
20
20
33 32 31 30 29 28 27 26 25 24 23
DZF2 RIN+ RIN– LIN+ LIN– ROUT1 LOUT1 ROUT2 LOUT2 ROUT3 LOUT3
XIN XOUT XMCK DVDD DGND XSTATE DATAO LRCK BCK CKOUT
ST-S5
5-10.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 M30622MGA-A39FP (SYSTEM CONTROLLER) Pin No.
Pin Name
I/O
Description
1
AMP-DATA
O
Serial data output to the M61512FP (IC607)
2
AMP-CLK
O
Serial data transfer clock signal output to the M61512FP (IC607)
3
AMP-LAT
O
Serial data latch pulse signal output to the M61512FP (IC607)
4
SIRCS
I
Remote control signal input from the remote control receiver (IC101)
5
DIG-TX
O
Serial data output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital filter (IC606)
6
DSP-RX
I
Serial data input from the digital audio interface receiver (IC604)
7
DIG-CLK
O
Serial data transfer clock signal output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital filter (IC606)
8
GND
—
Ground terminal
9
CNVSS
—
Not used
10
XCIN
I
Sub system clock input terminal (32.768 kHz)
11
XCOUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC551) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
XOUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
XIN
I
16
VCC
—
17
NMI
I
Non-maskable interrupt input terminal Fixed at “H” in this set
18
RDS-INT
I
Serial data transfer clock signal from the RDS decoder on the FM/AM tuner unit
19
—
—
20
RDS-DATA
I
Serial data input from the RDS decoder on the FM/AM tuner unit
21
ST-MUTE
O
Tuner muting on/off control signal output to the FM/AM tuner unit “L”: muting on
22
ST-CE
O
Chip enable signal output to the FM/AM tuner unit
23
ST-DOUT
O
Serial data output to the FM/AM tuner unit
24
—
—
Not used (open)
25
ST-DIN
I
26
—
—
Not used (open)
27
ST-CLK
O
Serial data transfer clock signal output to the FM/AM tuner unit
28
—
—
Not used (open)
29
IIC CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the display controller (IC601) and CDP-S3
Main system clock input terminal (16 MHz) Power supply terminal (+5V)
Not used (open)
Serial data input from the FM/AM tuner unit
30
IIC DATA
I/O
Communication data bus with the display controller (IC601) and CDP-S3
31 to 34
NO-USE
—
Not used
35 to 40
—
—
Not used (open)
41
M-RESET
O
Reset signal output to the display controller (IC601) “L”: reset
42 to 50
—
—
Not used (open)
51
NO-USE
—
Not used
52 to 57
—
—
Not used (open)
58
EXP-IN DATA
I
Serial data input from the I/O expander in the TA-S7AV
59
EXP-OUT DATA
O
Serial data output to the I/O expander in the TA-S7AV
60
EXP-LAT
O
Serial data latch pulse signal output to the I/O expander in the TA-S7AV
61
EXP-CLK
O
Serial data transfer clock signal output to the I/O expander in the TA-S7AV
62
VCC
—
63
SOFT-TEST
I
Power supply terminal (+5V) Soft test output terminal Not used (open)
21
ST-S5
Pin No.
Pin Name
I/O
Description
64
VSS
—
Ground terminal
65 to 70
—
—
Not used (open)
71
LINE-MUTE
O
Audio line muting on/off control signal output to the audio line circuit “L”: muting on
72
—
—
Not used (open)
73
DISPLAY KEY
I
DISPLAY switch (S601) input terminal
74
POWER KEY
I
Power on/off switch in the TA-S7AV input terminal
75
DIR-UNLOCK
I
PLL lock error and data error flag input from the digital audio interface receiver (IC604)
76
DIR-CS
O
Chip enable signal output to the digital audio interface receiver (IC604)
77
DIR-XSTATE
I
Source clock switching monitor input from the digital audio interface receiver (IC604)
78
DIR-RX
I
Read data input from the digital audio interface receiver (IC604)
79
CODEC-SMUTE
O
Soft muting on/off control signal output to the A/D, D/A converter (IC605) “L”: muting on
80
DSP-ACK
I
Acknowledge signal input from the CXD9617R (IC601)
81
DSP-CS
O
Chip select signal output to the CXD9617R (IC601)
82
DSP-DECODE
O
Decode signal input from the CXD9617R (IC601)
83 to 86
—
—
Not used (open)
87
STEREO
I
FM stereo detection signal input from the FM/AM tuner unit “L”: stereo Tuning detection signal input from the FM/AM tuner unit “L”: tuned
88
TUNED
I
89 to 91
—
—
92
MODEL-IN
I
Model setting terminal
93
SPEC-IN
I
Specification setting terminal
94
—
—
Not used (open)
95
V-MUTE
O
Video muting on/off control signal output terminal “L”: muting on Not used (open)
96
AVSS
—
Ground terminal
97
—
—
Not used (open)
98
VREF
I
99
AVCC
—
100
AC-CUT
I
22
Not used (open)
Reference voltage (+5V) input terminal Power supply terminal (+5V) AC cut on/off detection signal input from the reset signal generator (IC551) “L”: AC cut on, “H”: AC cut off or checked
ST-S5
• DSP BOARD IC601 CXD9617R (AUDIO DIGITAL SIGNAL PROCESSOR) Pin No.
Pin Name
I/O
Description
1
VSS
—
2
XRST
I
Reset signal input from the M61512FP (IC607) “L”: reset
3
EXTIN
I
Master clock signal input terminal
4
FS2
I
Sampling frequency selection signal input terminal
5
VDDI
—
Ground terminal Not used (fixed at “L”) Not used (fixed at “L”)
Power supply terminal (+2.6V)
6
FS1
I
Sampling frequency selection signal input terminal
7
PLOCK
O
Internal PLL lock signal output terminal
8
VSS
—
Ground terminal
9
MCLK1
I
10
VDDI
—
Power supply terminal (+2.6V)
11
VSS
—
Ground terminal
12
MCLK2
O
Oscillation clock signal output terminal
Not used (fixed at “L”)
Not used (open)
Oscillation clock signal input from the digital audio interface receiver (IC604)
Not used (open)
13
MS
I
Master/slave selection signal input terminal “L”: slave, “H”: master (fixed at “L” in this set)
14
SCKOUT
O
Internal system clock signal output to the digital filter (IC606)
15
LRCKI1
I
L/R sampling clock signal (44.1 kHz) input terminal
16
VDDE
—
Not used (open)
Power supply terminal (+3.3V)
17
BCKI1
I
Bit clock signal (2.8224 MHz) input terminal
18
SDI1
I
Audio serial data input from the D/A, A/D converter (IC605)
19
LRCKO
O
L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter (IC606)
20
BCKO
O
Bit clock signal (2.8224 MHz) output to the D/A, A/D converter (IC605) and digital filter (IC606)
Not used (open)
21
VSS
—
22
KFSIO
I
Audio clock signal input from the digital audio interface receiver (IC604)
23 to 25
SDO1 to SDO3
O
Audio serial data output to the A/D, D/A converter (IC604)
26
SDO4
O
Audio serial data output to the digital filter (IC606)
Ground terminal
27
SPDIF
O
S/PIDF signal output terminal
28
LRCKI2
I
L/R sampling clock signal (44.1 kHz) input from the digital audio interface receiver (IC604)
29
BCKI2
I
Bit clock signal (2.8224 MHz) input from the digital audio interface receiver (IC604)
30
SDI2
I
Audio serial data input from the digital audio interface receiver (IC604)
31
VSS
—
Ground terminal
32
HACN
O
Acknowledge signal output to the system controller (IC501)
33
HDIN
I
Write data input from the system controller (IC501)
Not used (open)
34
HCLK
I
Clock signal input from the system controller (IC501)
35
HDOUT
O
Read data output to the system controller (IC501)
36
HCS
I
Chip select signal input from the system controller (IC501)
37
SDCLK
O
Clock signal output terminal
38
CLKEN
O
Clock enable signal output terminal
39
RAS
O
Row address strobe signal input terminal
40
VDDI
—
Power supply terminal (+2.6V)
Not used (open) Not used (open) Not used (open)
41
VSS
—
Ground terminal
42
CAS
O
Column address strobe signal output terminal
43
DQM
O
Output terminal of data input/output mask
Chip select signal output to the S-RAM (IC602)
Not used (open)
Not used (open)
44
CS0
O
45
WE0
O
Write enable signal output to the S-RAM (IC602)
46
VDDE
—
Power supply terminal (+3.3V)
47
WMD1
I
S-RAM wait mode setting terminal
Fixed at “H” in this set
23
ST-S5
Pin No.
Pin Name
I/O
Description
48
VSS
—
49
WMD0
I
S-RAM wait mode setting terminal Fixed at “L” in this set
50
PAGE2
O
Page selection signal output terminal Not used (open)
51
VSS
—
Ground terminal
52, 53
PAGE1, PAGE0
O
Page selection signal output terminal Not used (open)
54
BOOT
I
Boot mode control signal output terminal Not used (fixed at “L”)
55
BTACT
I
Boot mode state display signal output terminal Not used (open)
Ground terminal
56
BST
I
Boot trap signal input from the M61512FP (IC607)
57
MOD1
I
PLL input frequency select terminal
58
MOD0
I
Mode setting terminal
59
EXLOCK
I
PLL lock error and data error flag input from the digital audio interface receiver (IC604)
“L”: 384fs, “H”: 256fs (fixed at “H” in this set)
“L”: single chip mode, “H”: use prohibition (fixed at “L” in this set)
60
VDDI
—
Power supply terminal (+2.6V)
61
VSS
—
Ground terminal
62, 63
A17, A16
O
Address signal output terminal Not used (open)
64 to 66
A15 to A13
O
Address signal output to the S-RAM (IC602)
67
GP10
O
L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter (IC606)
68
DECODE
O
Decode signal output to the system controller (IC501)
69
AUDIO
I
Bit 1 input terminal of channel status from the digital audio interface receiver (IC604)
70
VDDI
—
Power supply terminal (+2.6V)
71
VSS
—
Ground terminal
72 to 75
D15 to D12
I/O
Two-way data bus with the S-RAM (IC602)
76
VDDE
—
Power supply terminal (+3.3V)
77 to 80
D11 to D8
I/O
Two-way data bus with the S-RAM (IC602)
81
VSS
—
Ground terminal
82 to 85
A9, A12 to A10
O
Address signal output to the S-RAM (IC602)
86
TDO
O
Simple emulation data output terminal Not used (open)
87
TMS
I
Simple emulation data input start/end detection signal input terminal Not used (open)
88
XTRST
I
Simple emulation asychronous break input terminal Not used (open)
89
TCK
I
Simple emulation clock signal input terminal Not used (open)
90
TDI
I
Simple emulation data input terminal Not used (open)
91
VSS
—
Ground terminal
92 to 97
A8 to A3
O
Address signal output to the S-RAM (IC602)
98, 99
D7, D6
I/O
Two-way data bus with the S-RAM (IC602)
100
VDDI
—
Power supply terminal (+2.6V)
101
VSS
—
Ground terminal
102 to 105
D5 to D2
I/O
Two-way data bus with the S-RAM (IC602)
106
VDDE
—
Power supply terminal (+3.3V)
107, 108
D1, D0
I/O
Two-way data bus with the S-RAM (IC602)
109, 110
A2, A1
O
Address signal output to the S-RAM (IC602)
111
VSS
—
Ground terminal
112
A0
O
Address signal output to the S-RAM (IC602)
113
PM
I
PLL reset signal input from the M61512FP (IC607) “L”: reset
114, 115
SDI3, SDI4
I
Audio serial data input terminal Not used (fixed at “L”)
116
SYNC
I
Synchronous/asychronous selection signal input terminal “L”: Synchronous, “H”: asynchronous (fixed at “H” in this set)
117 to 119
VSS
—
Ground terminal
120
VDDI
—
Power supply terminal (+2.6V)
24
ST-S5
• DSP BOARD IC604 LC89056W-E (DIGITAL AUDIO INTERFACE RECEIVER) Pin No.
Pin Name
I/O
Description
1
DISEL
I
Selection terminal of data input terminal Fixed at “L” in this set
2
DOUT
O
Digital data output to the optical transceiver (IC609)
3
DIN0
I
Digital data input from the optical receiver (IC952) (for CDP-S3)
4
DIN1
I
Digital data input from the optical receiver (IC951) (for external input)
5
DIN2
I
Digital data input terminal Not used (fixed at “L”)
6
DGND
—
Ground terminal (digital system)
7
DVDD
—
Power supply terminal (+3.3V) (digital system)
8
R
I
VCO gain control input terminal
9
VIN
I
VCO free run frequency setting input terminal
10
LPF
O
PLL loop filter setting output terminal
11
AVDD
—
Power supply terminal (+3.3V) (analog system)
12
AGND
—
Ground terminal (analog system)
13
CKOUT
O
Audio clock signal output to the CXD9617R (IC601)
14
BCK
O
Bit clock signal (2.8224 MHz) output to the CXD9617R (IC601)
15
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the CXD9617R (IC601)
16
DATAO
O
Audio serial data output to the CXD9617R (IC601)
17
XSTATE
O
Source clock switching monitor output to the system controller (IC501)
18
DGND
—
Ground terminal (digital system)
19
DVDD
—
Power supply terminal (+3.3V) (digital system)
20
XMCK
O
Oscillation clock signal output to the CXD9617R (IC601)
21
XOUT
O
System clock output terminal (13.5 MHz) System clock input terminal (13.5 MHz)
22
XIN
I
23
EMPHA
O
Emphasis information of channel status output terminal Not used (open)
24
AUDIO
O
Bit 1 output terminal of channel status to the CXD9617R (IC601)
25
CSFLAG
O
Top 40 bit renovation flag output terminal of channel status Not used (open)
26 to 28
F0 to F2
O
Input frequency calculation result output terminal Not used (open)
29
VF
O
Validity flag output terminal Not used (open)
30
DVDD
—
Power supply terminal (+3.3V) (digital system)
31
DGND
—
Ground terminal (digital system)
32
ERR9P
O
Nine times continuance data transmission error flag output terminal Not used (open)
33
BPSYNC
O
Non-PCM burst and preamble sync signal output terminal Not used (open)
34
ERROR
O
PLL lock error and data error flag output to the system controller (IC501)
35
DO
O
Read data output to the system controller (IC501)
36
DI
I
Write data input from the system controller (IC501)
37
CE
I
Chip enable signal input from the system controller (IC501)
38
CL
I
Clock signal input from the system controller (IC501)
39
XSEL
I
Selection input terminal of vibrator frequency terminal Fixed at “H” in this set
40
MODE0
I
Mode setting input terminal Fixed at “H” in this set
41
MODE1
I
Mode setting input terminal Fixed at “H” in this set
42
DGND
—
Ground terminal (digital system)
43
DVDD
—
Power supply terminal (+3.3V) (digital system)
44
DOSEL0
I
Output data format selection signal input terminal Fixed at “L” in this set
45
DOSEL1
I
Output data format selection signal input terminal Fixed at “L” in this set
46
CKSEL0
I
Output clock selection signal input terminal Fixed at “L” in this set
47
CKSEL1
I
Output clock selection signal input terminal Fixed at “L” in this set
48
XMODE
I
System reset signal input from the M61512FP (IC607)
25
ST-S5
• DSP BOARD IC605 AK4527 (A/D, D/A CONVERTER) Pin No.
Pin Name
I/O
Description
1
SDOS
I
Audio serial data source selection signal input terminal “L”: internal ADC output, “H”: DAUX input (fixed at “L” in this set)
2
I2C
I
Serial control mode selection signal input terminal “L”: 3-wire serial, “H”: I2C bus
3
SMUTE
I
Soft muting on/off signal input from the system controller (IC501) “L”: muting on
4
BICK
I
Bit clock signal (2.8224 MHz) input from the CXD9617R (IC601)
5
LRCK
I
L/R sampling clock (44.1 kHz) signal input from the CXD9617R (IC601)
6 to 8
SDTI1 to SDIT3
I
Audio serial data input from the CXD9617R (IC601)
9
SDTO
O
Audio serial data output to the CXD9617R (IC601)
10
DAUX
I
Audio serial data input terminal Not used (fixed at “L”)
11
DFS
I
Double speed sampling mode signal input terminal “L”: normal speed, “H”: double speed (fixed at “L” in this set)
12
DEM1
I
De-emphasis signal input terminal Fixed at “L” in this set De-emphasis signal input terminal Fixed at “H” in this set
13
DEM0
I
14
TVDD
—
Power supply terminal (+5V) (for output buffer )
15
DVDD
—
Power supply terminal (+5V) (digital system)
16
DVSS
—
Ground terminal (digital system)
17
PDN
I
Power down and reset signal input from the M61512FP (IC607) “L”: power down and reset
I
Input clock signal selection terminal Fixed at “L” in this set Chip address signal input terminal Not used (fixed at “L”)
18 to 20 ICKS2 to ICKS0 21, 22
CAD1, CAD0
I
23
LOUT3
O
Analog signal output for center to the M61512FP (IC607)
24
ROUT3
O
Analog signal output for sub woofer to the M61512FP (IC607)
25
LOUT2
O
Analog signal output for surround L-ch to the M61512FP (IC607)
26
ROUT2
O
Analog signal output for surround R-ch to the M61512FP (IC607)
27
LOUT1
O
Analog signal output for front L-ch to the M61512FP (IC607)
28
ROUT1
O
Analog signal output for front R-ch to the M61512FP (IC607)
29
LIN–
I
L-ch analog signal negative input from the M61512FP (IC607)
30
LIN+
I
L-ch analog signal positive input from the M61512FP (IC607)
31
RIN–
I
R-ch analog signal negative input from the M61512FP (IC607)
32
RIN+
I
R-ch analog signal positive input from the M61512FP (IC607)
33
DZF2
O
Zero input detection terminal
34
VCOM
O
Common voltage output terminal Large external capacitor is used to reduce power supply noise
35
VREFH
I
Reference voltage (+5V) input terminal
36
AVDD
—
Power supply terminal (+5V) (analog system)
37
AVSS
—
Ground terminal (analog system)
38
DZF1
O
Zero input detection terminal
39
MCLK
I
Master clock signal input from the CXD9617R (IC601)
40
P/S
I
Parallel/serial selection signal input terminal “L”: serial control mode, “H”: parallel control mode (fixed at “H” in this set)
41
DIF0
I
Audio data interface format terminal Fixed at “L” in this set
42
DIF1
I
Audio data interface format terminal Fixed at “H” in this set
43, 44
LOOP0, LOOP1
I
Loop back mode setting terminal Fixed at “L” in this set
26
Not used (open)
Not used (open)
ST-S5
• PANEL BOARD IC601 MB90M407PF-G-102-BND (DISPLAY CONTROLLER) Pin No.
Pin Name
I/O
Description
1 to 6
G6 to G1
O
Grid drive signal output to the fluorescent indicator tube (FL601)
7 to 10
A1 to A4
O
Segment drive signal output to the fluorescent indicator tube (FL601)
11
VSS FOR IO
—
Ground terminal (for I/O)
12 to 22
A5 to A15
O
Segment drive signal output to the fluorescent indicator tube (FL601)
23
VDD FOR VFT
—
Power supply terminal (+3.3V) (for VFT)
24 to 41
A16 to A33
O
Segment drive signal output to the fluorescent indicator tube (FL601)
42
VSS FOR IO
—
Ground terminal (for I/O)
43 to 47
A34 toA38
O
Segment drive signal output to the fluorescent indicator tube (FL601)
48
VKK FOR VFT
—
Power supply terminal (–28V) (for VFT)
49
MODE0
—
Chip mode selection terminal
Not used (fixed at “H”)
50
MODE1
—
Chip mode selection terminal
Not used (fixed at “H”)
51
MODE2
—
Chip mode selection terminal
Not used (fixed at “L”)
52
JOG2B
I
Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (B phase input)
53
JOG2A
I
Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (A phase input)
54
JOG1B
I
Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (B phase input)
55
JOG1A
I
Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (A phase input)
56
VOLA
I
Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (A phase input)
57
VOLB
I
Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (B phase input)
58, 59
—
—
Not used (open)
60
I2C DATA
I/O
Communication data bus with the system controller (IC501) and CDP-S3
61
I2C CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the system controller (IC501) and CDP-S3
62
AVCC FOR ANALOG
—
Power supply terminal (+3.3V) (for analog)
63
AVSS FOR ANALOG
—
Ground terminal (for analog)
64
KEY0
I
Key input terminal (A/D input) CLOCK/TIMER, TIMER SELECT, TUNER/BAND, TUNING +/–, ENTER, PRESET +/–, TUNER MEMORY, STEREO/MONO, PTY (S602 to S612) keys input PTY (S612) key: Used for the AEP and UK models only
65
KEY1
I
Key input terminal for TA-S7AV (A/D input)
66 to 76
—
—
77
RESET
I
Not used (open) Reset signal input from the system controller (IC501) “L”: reset
78 to 80
—
—
Not used (open)
81
VSS FOR CPU
—
Ground terminal (for CPU)
82
XIN
I
System clock input terminal (4 MHz)
83
XOUT
O
System clock output terminal (4 MHz)
84
VCC FOR CPU
—
Power supply terminal (+3.3V)
85 to 91
—
—
Not used (open)
92 to 94
G12
O
Grid drive signal output to the fluorescent indicator tube (FL601)
95 to 98
G11 to G8
O
Grid drive signal output to the fluorescent indicator tube (FL601)
99, 100
G7
O
Grid drive signal output to the fluorescent indicator tube (FL601)
27
ST-S5 SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied.
• Abbreviation AUS : Australian model KR : Korean model MX : Mexican model
6-1. COVER, FRONT PANEL SECTION 8 #2
7
5
4
1
6 5 7
3 AEP, UK
5
2
#1
Ref. No.
Part No.
Description
1 1 2 3 4
X-4953-451-1 X-4953-452-1 1-773-114-11 4-232-351-01 1-680-697-11
PANEL ASSY (ST), FRONT (AEP, UK) PANEL ASSY (ST), FRONT (KR, MX, AUS) WIRE (FLAT TYPE) (19 CORE) FILTER (FL) SIRCS BOARD
5
4-951-620-01 SCREW (2.6X8), +BVTP
28
Remark
Ref. No.
Part No.
Description
Remark
6 6 7 8 #1
A-4476-267-A A-4476-269-A 3-363-099-21 4-233-134-31 7-685-646-79
PANEL BOARD, COMPLETE (AEP, UK) PANEL BOARD, COMPLETE (KR, MX, AUS) SCREW (CASE 3 TP2) COVER SCREW +BVTP 3X8 TYPE2 N-S
#2
7-685-871-01 SCREW +BVTT 3X6 (S)
ST-S5
6-2. CHASSIS SECTION
56 55 54 #1
57 #1 #1 #1
53 63
#1
58 52
#1
(Including
not supplied
A)
#1 #1
A
59
61
60
51 62
not supplied not supplied
Ref. No.
Part No.
Description
* 51 52 52 52 53
4-924-098-01 A-2007-939-A A-4476-193-A A-4476-203-A A-4476-199-A
HOLDER, PC BOARD MAIN BOARD, COMPLETE (MX) MAIN BOARD, COMPLETE (AEP, UK) MAIN BOARD, COMPLETE (KR, AUS) DSP BOARD, COMPLETE (AEP, UK)
53 53 54 55 56
A-4476-646-A A-4726-352-A 1-757-599-11 1-757-600-11 1-757-629-11
DSP BOARD, COMPLETE (MX) DSP BOARD, COMPLETE (KR, AUS) WIRE (FLAT TYPE) (21 CORE) WIRE (FLAT TYPE) (23 CORE) CORD (WITH CONNECTOR) 5P
57 58
1-757-631-11 CORD (WITH CONNECTOR) 20P 1-757-630-11 CORD (WITH CONNECTOR) 19P
Remark
Ref. No.
Part No.
Description
Remark
59 59 59 59 60
4-232-327-01 4-232-327-11 4-232-327-41 4-232-327-91 1-769-940-11
PANEL (ST), BACK (AEP, UK) PANEL (ST), BACK (AUS) PANEL (ST), BACK (MX) PANEL (ST), BACK (KR) WIRE (FLAT TYPE) (11 CORE) (KR, MX, AUS)
60 61 61 61 62
1-773-004-11 1-693-529-11 1-693-531-71 1-693-538-11 4-965-822-01
WIRE (FLAT TYPE) (15 CORE) (AEP, UK) TUNER PACK (FM/AM) (AEP, UK) TUNER PACK (FM/AM) (MX, AUS) TUNER PACK (FM/AM) (KR) FOOT
63 #1
3-970-608-01 SUMITITE (B3), +BV 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
29
ST-S5 SECTION 7 ELECTRICAL PARTS LIST
DSP NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Abbreviation AUS : Australian model KR : Korean model MX : Mexican model Ref. No.
Part No.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . • CAPACITORS uF: µF • COILS uH: µH
Description
Remark
A-4476-199-A DSP BOARD, COMPLETE (AEP, UK) A-4476-646-A DSP BOARD, COMPLETE (MX) A-4726-352-A DSP BOARD, COMPLETE (KR, AUS) ******************** < CAPACITOR > C601 C602 C603 C604 C606
1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-164-156-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.01uF 0.1uF 0.1uF 0.1uF
C607 C608 C609 C610 C611
1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
25V 25V 25V 25V 25V
C612 C613 C614 C615 C616
1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-126-934-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.1uF 0.1uF 0.1uF 0.1uF 220uF
25V 25V 25V 25V 10V
C617 C618 C619 C620 C621
1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.01uF 0.1uF 0.1uF 0.01uF
C622 C623 C624 C625 C626
1-164-156-11 1-126-934-11 1-164-156-11 1-162-915-11 1-162-915-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 220uF 0.1uF 10PF 10PF
C627 C628 C629 C630 C631
1-164-156-11 1-164-156-11 1-164-156-11 1-162-970-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.01uF 0.01uF
C632 C633 C634 C635 C636
1-164-156-11 1-126-934-11 1-164-156-11 1-164-156-11 1-162-970-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 220uF 0.1uF 0.1uF 0.01uF
C637 C638 C639
1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP
0.01uF 0.01uF 0.01uF
30
10%
20%
10%
10%
25V 25V 25V 25V 25V
25V 25V 25V 25V 25V
0.5PF 0.5PF
25V 10V 25V 50V 50V
10% 10%
25V 25V 25V 25V 25V
20%
10%
25V 10V 25V 25V 25V
10% 10% 10%
25V 25V 25V
20%
Ref. No.
Part No.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Description
Remark
C640 C641
1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP
0.01uF 0.01uF
10% 10%
25V 25V
C642 C643 C644 C645 C646
1-162-971-11 1-162-971-11 1-164-156-11 1-126-934-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.001uF 0.001uF 0.1uF 220uF 0.01uF
10% 10%
50V 50V 25V 10V 25V
C647 C648 C649 C650 C651
1-126-934-11 1-126-934-11 1-164-360-11 1-126-934-11 1-164-360-11
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
220uF 220uF 0.1uF 220uF 0.1uF
20% 20%
C652 C653 C654 C655 C656
1-164-360-11 1-162-970-11 1-162-970-11 1-164-360-11 1-126-934-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.1uF 0.01uF 0.01uF 0.1uF 220uF
C657 C658 C659 C660 C661
1-162-971-11 1-164-156-11 1-126-934-11 1-126-934-11 1-126-934-11
CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT
0.001uF 0.1uF 220uF 220uF 220uF
C662 C664 C665 C666 C667
1-164-156-11 1-164-156-11 1-164-156-11 1-126-934-11 1-126-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
C668 C669 C670 C671 C672
1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11
C673 C674 C675 C676 C677
20% 10%
20%
10% 10% 20% 10%
10V 10V 16V 10V 16V 16V 25V 25V 16V 10V
20% 20% 20%
50V 25V 10V 10V 10V
0.1uF 0.1uF 0.1uF 220uF 10uF
20% 20%
25V 25V 25V 10V 50V
ELECT ELECT ELECT ELECT ELECT
10uF 10uF 10uF 10uF 10uF
20% 20% 20% 20% 20%
50V 50V 50V 50V 50V
1-126-964-11 1-126-964-11 1-126-193-11 1-126-193-11 1-126-193-11
ELECT ELECT ELECT CHIP ELECT CHIP ELECT CHIP
10uF 10uF 1uF 1uF 1uF
20% 20% 20% 20% 20%
50V 50V 50V 50V 50V
C678 C679 C680 C681 C682
1-126-964-11 1-164-156-11 1-126-964-11 1-126-193-11 1-126-193-11
ELECT CERAMIC CHIP ELECT ELECT CHIP ELECT CHIP
10uF 0.1uF 10uF 1uF 1uF
20% 20% 20% 20%
50V 25V 50V 50V 50V
C683
1-126-193-11 ELECT CHIP
1uF
20%
50V
ST-S5 DSP Ref. No.
Part No.
Description
C684 C685 C686 C687
1-126-964-11 1-126-964-11 1-126-933-11 1-126-933-11
ELECT ELECT ELECT ELECT
10uF 10uF 100uF 100uF
20% 20% 20% 20%
50V 50V 16V 16V
Remark
C689 C690 C691 C692 C693
1-126-933-11 1-126-934-11 1-164-156-11 1-136-165-00 1-136-165-00
ELECT ELECT CERAMIC CHIP MYLAR MYLAR
100uF 220uF 0.1uF 0.1uF 0.1uF
20% 20% 5% 5%
16V 10V 25V 50V 50V
C694 C695 C699 C700 C701
1-136-165-00 1-136-165-00 1-126-964-11 1-126-964-11 1-126-193-11
MYLAR MYLAR ELECT ELECT ELECT CHIP
0.1uF 0.1uF 10uF 10uF 1uF
5% 5% 20% 20% 20%
50V 50V 50V 50V 50V
C702 C703 C704 C705 C706
1-126-960-11 1-126-960-11 1-126-961-11 1-126-964-11 1-126-964-11
ELECT ELECT ELECT ELECT ELECT
1uF 1uF 2.2uF 10uF 10uF
20% 20% 20% 20% 20%
50V 50V 50V 50V 50V
C707 C708 C709 C710 C711
1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-162-962-11
ELECT ELECT ELECT ELECT CERAMIC CHIP
10uF 10uF 10uF 10uF 470PF
20% 20% 20% 20% 10%
50V 50V 50V 50V 50V
C712 C713 C714 C715 C716
1-162-962-11 1-162-957-11 1-162-957-11 1-162-957-11 1-162-957-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
470PF 220PF 220PF 220PF 220PF
10% 5% 5% 5% 5%
50V 50V 50V 50V 50V
C717 C719 C720 C721 C722
1-164-156-11 1-164-156-11 1-162-957-11 1-126-934-11 1-164-156-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.1uF 0.1uF 220PF 220uF 0.1uF
C723 C724 C725 C726 C727
1-126-964-11 1-164-156-11 1-126-964-11 1-164-156-11 1-126-964-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
10uF 0.1uF 10uF 0.1uF 10uF
C728 C729 C730 C731 C732
1-164-156-11 1-126-964-11 1-126-964-11 1-164-156-11 1-164-156-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
0.1uF 10uF 10uF 0.1uF 0.1uF
C733 C735 C736 C738 C739
1-164-156-11 1-164-156-11 1-164-156-11 1-164-357-11 1-164-357-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.001uF 0.001uF
C740 C741 C742
1-164-156-11 CERAMIC CHIP 1-164-156-11 CERAMIC CHIP 1-164-357-11 CERAMIC CHIP
0.1uF 0.1uF 0.001uF
5% 20%
20% 20% 20%
20% 20%
25V 25V 50V 10V 25V 50V 25V 50V 25V 50V 25V 50V 50V 25V 25V
5% 5%
25V 25V 25V 50V 50V
5%
25V 25V 50V
< CONNECTOR > CN601 CN602 CN603
1-506-469-11 PIN, CONNECTOR 4P 1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
Ref. No.
Part No.
Description
Remark
< DIODE/RESISTOR > D601 D604 D605 D606 D607
8-719-158-02 8-719-988-61 8-719-988-61 1-216-864-11 8-719-058-24
DIODE RD3.9SB2 DIODE 1SS355TE-17 DIODE 1SS355TE-17 METAL CHIP 0 5% DIODE RB501V-40TE-17 (E, AUS)
D608 D609 D610
8-719-058-24 DIODE RB501V-40TE-17 (E, AUS) 8-719-058-24 DIODE RB501V-40TE-17 (E, AUS) 8-719-058-24 DIODE RB501V-40TE-17 (E, AUS)
1/16W
< GROUND TERMINAL > * EP602 * EP603 * EP604
1-537-738-21 TERMINAL, EARTH 1-537-738-21 TERMINAL, EARTH 1-537-738-21 TERMINAL, EARTH < FERRITE BEAD/RESISTOR >
FB601 FB602 FB603 FB604 FB605
1-216-864-11 1-216-864-11 1-500-445-21 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP FERRITE METAL CHIP METAL CHIP
0 0 0uH 0 0
5% 5%
1/16W 1/16W
5% 5%
1/16W 1/16W
FB606 FB607 FB608
1-216-805-11 METAL CHIP 1-500-445-21 FERRITE 1-500-445-21 FERRITE
47 0uH 0uH
5%
1/16W
< IC > IC601 IC602 IC603 IC604 IC605
8-759-698-76 8-759-827-81 8-759-238-47 8-759-825-15 8-759-657-47
IC IC IC IC IC
CXD9617R IS61LV6416-15T (T&R) TC74HCT7007AF (EL) LC89056W-E AK4527
IC606 IC607 IC608 IC609 IC610
8-759-825-13 8-749-018-85 8-759-549-25 8-749-923-04 8-759-835-63
IC IC IC IC IC
PCM1748E/2K M61512FP SN74LVU04APWR TOTX178A (OPTICAL OUT) NJM2391DL1-26-TE1
< JACK > J601 J602
1-774-411-11 JACK, PIN 6P (VIDEO (AUDIO) IN, MD IN/OUT) 1-774-785-11 JACK, PIN 1P (SUB WOOFER OUT) < JUNPER RESISTOR >
JR601 JR603 JR620 JR621 JR622
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
< TRANSISTOR > Q601 Q602 Q603 Q604 Q605
8-729-801-93 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SD1387 2SC1623-L5L6 2SC1623-L5L6 2SC1623-L5L6 2SC1623-L5L6
Q606 Q607 Q608 Q609
8-729-141-73 8-729-141-73 8-729-141-73 8-729-141-73
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC3624A-T1L15L16 2SC3624A-T1L15L16 2SC3624A-T1L15L16 2SC3624A-T1L15L16
31
ST-S5 DSP Ref. No.
Part No.
Description
Remark
Q610
8-729-141-73 TRANSISTOR
2SC3624A-T1L15L16
Q611 Q612 Q613
8-729-141-73 TRANSISTOR 8-729-113-69 TRANSISTOR 8-729-113-14 TRANSISTOR
2SC3624A-T1L15L16 FN1F4M-M32 FA1A4M-T1L33
< RESISTOR > R601 R602 R603 R604 R605
1-216-809-11 1-216-821-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 1K 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R606 R607 R608 R610 R611
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R612 R613 R614 R615 R616
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R617 R618 R619 R620 R621
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R623 R628 R629 R630 R631
1-216-833-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R632 R633 R634 R635 R636
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R637 R638 R639 R640 R641
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R642 R643 R644 R645 R646
1-216-809-11 1-216-815-11 1-216-815-11 1-216-815-11 1-216-815-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 330 330 330 330
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R647 R648 R649 R650 R651
1-216-815-11 1-216-815-11 1-216-817-11 1-216-817-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
330 330 470 470 470
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R652 R653 R654 R655 R656
1-216-817-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 10K 10K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R657
1-216-809-11 METAL CHIP
100
5%
1/16W
32
Ref. No.
Part No.
Description
R658 R659 R660 R661
1-216-809-11 1-216-809-11 1-216-815-11 1-216-815-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 330 330
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
Remark
R662 R663 R664 R665 R666
1-216-809-11 1-216-817-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 470 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R667 R668 R669 R670 R671
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R672 R673 R674 R675 R676
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R677 R678 R679 R680 R681
1-216-830-11 1-216-833-11 1-216-829-11 1-216-827-11 1-216-839-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
5.6K 10K 4.7K 3.3K 33K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R682 R683 R684 R685 R686
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R687 R688 R689 R690 R691
1-216-809-11 1-216-809-11 1-216-821-11 1-216-857-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 1K 1M 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R692 R693 R694 R695 R696
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-824-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 1.8K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R697 R698 R699 R700 R701
1-216-824-11 1-216-853-11 1-216-853-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.8K 470K 470K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R702 R703 R706 R707 R709
1-216-857-11 1-216-857-11 1-216-841-11 1-216-841-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1M 1M 47K 47K 0
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R711 R712 R713 R715 R716
1-216-821-11 1-216-841-11 1-216-821-11 1-216-821-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 47K 1K 1K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R717 R719 R720 R721
1-216-821-11 1-216-821-11 1-216-841-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 47K 1K
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
ST-S5 DSP Ref. No.
Part No.
Description
Remark
R723
1-216-821-11 METAL CHIP
1K
5%
1/16W
R724 R725 R727 R728 R729
1-216-841-11 1-216-821-11 1-216-821-11 1-216-841-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 1K 1K 47K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R730 R731 R733 R734 R735
1-216-837-11 1-216-829-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 4.7K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R738 R739 R742 R743 R746
1-216-821-11 1-216-835-11 1-216-835-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 15K 15K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R747 R748 R749 R750 R751
1-216-845-11 1-216-845-11 1-216-834-11 1-216-834-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 12K 12K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R752 R754 R755 R756 R757
1-216-841-11 1-216-809-11 1-216-809-11 1-216-841-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 100 100 47K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R758 R759 R760 R761 R762
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R763 R765 R766 R767 R768
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R769 R770 R771 R772 R773
1-216-821-11 1-216-821-11 1-216-833-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 10K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R774 R775 R776 R777 R778
1-216-821-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 10K 10K 10K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W (E, AUS)
Ref. No.
Part No.
MAIN
Description
Remark
A-2007-939-A MAIN BOARD, COMPLETE (MX) A-4476-193-A MAIN BOARD, COMPLETE (AEP, UK) A-4476-203-A MAIN BOARD, COMPLETE (KR, AUS) ********************* 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S < CAPACITOR >
R779 R780 R781
1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP
47K 47K 47K
5% 5% 5%
1/16W 1/16W 1/16W
< VIBRATOR > X601 1-579-993-21 VIBRATOR, CERAMIC (13.5MHz) **************************************************************
C501 C502 C503 C504 C505
1-162-205-31 1-162-203-31 1-164-159-11 1-164-159-11 1-126-916-11
CERAMIC CERAMIC CERAMIC CERAMIC ELECT
18PF 15PF 0.1uF 0.1uF 1000uF
5% 5%
C506 C508 C509 C510 C519
1-126-963-11 1-126-964-11 1-164-159-11 1-126-963-11 1-162-282-31
ELECT ELECT CERAMIC ELECT CERAMIC
4.7uF 10uF 0.1uF 4.7uF 100PF
C520 C551 C552 C553 C561
1-162-282-31 1-126-964-11 1-164-159-11 1-164-159-11 1-164-159-11
CERAMIC ELECT CERAMIC CERAMIC CERAMIC
100PF 10uF 0.1uF 0.1uF 0.1uF
10% 20%
50V 50V 50V 50V 50V
C562 C902 C903 C904 C905
1-162-306-11 1-126-935-11 1-126-964-11 1-126-936-11 1-126-935-11
CERAMIC ELECT ELECT ELECT ELECT
0.01uF 470uF 10uF 3300uF 470uF
30% 20% 20% 20% 20%
16V 10V 50V 16V 16V
C906 C907 C909 C910 C915
1-164-159-11 1-126-934-11 1-126-968-11 1-126-964-11 1-126-948-11
CERAMIC ELECT ELECT ELECT ELECT
0.1uF 220uF 100uF 10uF 100uF
20% 20% 20% 20%
50V 10V 50V 50V 35V
C916 C918 C927 C928 C937
1-162-306-11 1-126-935-11 1-164-159-11 1-164-159-11 1-164-159-11
CERAMIC ELECT CERAMIC CERAMIC CERAMIC
0.01uF 470uF 0.1uF 0.1uF 0.1uF
30% 20%
16V 10V 50V 50V 50V
C941 C942 C943 C952 C953
1-126-964-11 1-126-935-11 1-164-159-11 1-128-548-11 1-164-159-11
ELECT ELECT CERAMIC ELECT CERAMIC
10uF 470uF 0.1uF 4700uF 0.1uF
20% 20%
50V 6.3V 50V 25V 50V
C955 C956 C957 C961 C962
1-162-306-11 1-126-964-11 1-162-306-11 1-164-159-11 1-126-964-11
CERAMIC ELECT CERAMIC CERAMIC ELECT
0.01uF 10uF 0.01uF 0.1uF 10uF
30% 20% 30% 20%
16V 50V 16V 50V 50V
C964 C966 C968 C970 C971
1-162-306-11 1-162-306-11 1-162-306-11 1-162-306-11 1-162-306-11
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
0.01uF 0.01uF 0.01uF 0.01uF 0.01uF
30% 30% 30% 30% 30%
16V 16V 16V 16V 16V
C972 C977 C978 C991 C992
1-164-159-11 1-126-964-11 1-126-964-11 1-164-159-11 1-164-159-11
CERAMIC ELECT ELECT CERAMIC CERAMIC
0.1uF 10uF 10uF 0.1uF 0.1uF
20% 20% 20% 20% 10%
20%
20% 20%
50V 50V 50V 50V 6.3V 50V 50V 50V 50V 50V
50V 50V 50V 50V 50V
33
ST-S5 MAIN Ref. No.
Part No.
Description
Remark
CN502 * CN505
Ref. No. Q902
< CONNECTOR >
CN506 CN506 CN508
1-784-780-11 CONNECTOR, FFC 19P 1-569-624-11 SOCKET, CONNECTOR 17P (SYSTEM CONTROL 3) 1-568-830-11 CONNECTOR, FFC 11P (E, AUS) 1-784-776-11 CONNECTOR, FFC 15P (AEP, UK) 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CN509 CN510 CN5031 CN5032 CN5041
1-779-289-11 1-794-569-11 1-794-569-11 1-691-907-11 1-580-176-11
CONNECTOR, FFC (LIF (NON-ZIF)) 21P PIN, CONNECTOR 5P PIN, CONNECTOR 5P PIN, CONNECTOR 15P PIN, CONNECTOR 10P
Part No.
Description
8-729-011-92 TRANSISTOR
Remark 2SC2001TP-K1K2
< RESISTOR > R501 R502 R503 R504 R505
1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
100 100 100 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R506 R507 R508 R509 R510
1-247-807-31 1-247-807-31 1-249-429-11 1-247-891-00 1-249-411-11
CARBON CARBON CARBON CARBON CARBON
100 100 10K 330K 330
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R511 R512 R513 R514 R515
1-249-429-11 1-247-807-31 1-247-807-31 1-247-807-31 1-249-417-11
CARBON CARBON CARBON CARBON CARBON
10K 100 100 100 1K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R516 R517 R518 R519 R520
1-247-807-31 1-247-807-31 1-247-807-31 1-249-429-11 1-249-429-11
CARBON CARBON CARBON CARBON CARBON
100 100 100 10K 10K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R521 R522 R523 R524 R525
1-247-807-31 1-249-429-11 1-247-807-31 1-249-437-11 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
100 10K 100 47K 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R526 R527 R528 R529 R530
1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
100 100 100 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R531 R532 R533 R534 R535
1-247-807-31 1-249-437-11 1-247-807-31 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
100 47K 100 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R536 R537 R538 R539 R540
1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
100 100 100 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R541 R542 R543 R544 R545
1-249-437-11 1-249-437-11 1-249-407-11 1-249-425-11 1-249-417-11
CARBON CARBON CARBON CARBON CARBON
47K 47K 150 4.7K 1K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W (MX)
R545
1-249-425-11 CARBON
4.7K
5%
R545
1-249-429-11 CARBON
10K
5%
R546
1-249-407-11 CARBON
150
5%
R546
1-249-425-11 CARBON
4.7K
5%
R548
1-249-425-11 CARBON
4.7K
5%
1/4W (KR, AUS) 1/4W (AEP, UK) 1/4W (KR, AUS) 1/4W (MX) 1/4W
* CN5042 1-568-419-11 PIN, CONNECTOR 9P < DIODE > D551 D552 D901 D902 D903
8-719-911-19 8-719-911-19 8-719-500-56 8-719-024-99 8-719-024-99
DIODE DIODE DIODE DIODE DIODE
1SS199-25 1SS199-25 D3SBA20 11ES2-NTA2B (AEP, UK) 11ES2-NTA2B
D904 D911 D912 D913 D920
8-719-024-99 8-719-024-99 8-719-110-72 8-719-109-89 8-719-024-99
DIODE DIODE DIODE DIODE DIODE
11ES2-NTA2B 11ES2-NTA2B RD30ESB2 RD5.6ESB2 11ES2-NTA2B
D921 D922 D923 D941 D942
8-719-911-19 8-719-024-99 8-719-024-99 8-719-911-19 8-719-911-19
DIODE DIODE DIODE DIODE DIODE
1SS199-25 11ES2-NTA2B 11ES2-NTA2B 1SS199-25 1SS199-25
D943 D944 D945
8-719-911-19 DIODE 1SS199-25 8-719-911-19 DIODE 1SS199-25 8-719-911-19 DIODE 1SS199-25 < GROUND TERMINAL >
EPT901 1-537-770-21 TERMINAL BOARD, GROUND EPT902 1-537-770-21 TERMINAL BOARD, GROUND < IC > IC501 IC551 IC901 IC903 IC904
8-759-827-45 8-759-635-63 8-759-158-62 8-759-656-35 8-759-039-69
IC IC IC IC IC
M30622MGA-A39FP M51943BSL TA78057S NJM7810FA uPC7805AHF
IC951 IC952 IC991
8-749-923-05 IC TORX178B (OPTICAL IN) 8-749-923-05 IC TORX178B (OPTICAL IN) 8-759-982-15 IC RC7815FA < COIL >
L951 L955
1-414-193-41 INDUCTOR 1-410-682-31 INDUCTOR
220uH 470uH
< TRANSISTOR > Q502 Q503 Q551 Q901
34
8-729-422-57 8-729-422-57 8-729-620-05 8-729-140-97
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
UN4111 UN4111 2SC2603-EF 2SB734-34
ST-S5 MAIN Ref. No.
Part No.
Description
R549 R550 R551 R552 R553
1-247-843-11 1-249-441-11 1-249-413-11 1-249-429-11 1-249-437-11
CARBON CARBON CARBON CARBON CARBON
3.3K 100K 470 10K 47K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
Remark
R554 R555 R556 R557 R558
1-249-437-11 1-249-407-11 1-249-437-11 1-249-433-11 1-247-903-00
CARBON CARBON CARBON CARBON CARBON
47K 4.7K 47K 22K 1M
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
0 R903 R904 R905 R906 R908
1-219-153-11 1-249-429-11 1-247-807-31 1-247-807-31 1-249-417-11
FUSIBLE CARBON CARBON CARBON CARBON
10 10K 100 100 1K
5% 5% 5% 5% 5%
1/4W F 1/4W 1/4W 1/4W 1/4W
R911 R912 R941 R942 R943
1-249-409-11 1-249-442-11 1-249-417-11 1-249-417-11 1-247-843-11
CARBON CARBON CARBON CARBON CARBON
220 510 1K 1K 3.3K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R951 R952 R956 R957 R958
1-249-413-11 1-249-413-11 1-247-807-31 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
470 470 100 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R959 R961 R962 R963 R964
1-247-807-31 1-249-421-11 1-249-421-11 1-249-426-11 1-249-426-11
CARBON CARBON CARBON CARBON CARBON
100 2.2K 2.2K 5.6K 5.6K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R965 R966
1-247-807-31 CARBON 1-247-807-31 CARBON
100 100
5% 5%
1/4W 1/4W
Ref. No.
Part No.
PANEL
Description
Remark
C653 C654
1-162-282-31 CERAMIC 1-162-282-31 CERAMIC
100PF 100PF
10% 10%
50V 50V
C655 C656 C657 C658 C659
1-162-282-31 1-162-282-31 1-162-282-31 1-162-282-31 1-162-282-31
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
100PF 100PF 100PF 100PF 100PF
10% 10% 10% 10% 10%
50V 50V 50V 50V 50V
C660 C661 C662 C663 C664
1-162-282-31 1-162-282-31 1-162-282-31 1-162-306-11 1-164-159-11
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
100PF 100PF 100PF 0.01uF 0.1uF
10% 10% 10% 30%
50V 50V 50V 16V 50V
C665 C666 C667 C668 C669
1-126-963-11 1-126-963-11 1-164-159-11 1-164-159-11 1-164-159-11
ELECT ELECT CERAMIC CERAMIC CERAMIC
4.7uF 4.7uF 0.1uF 0.1uF 0.1uF
20% 20%
50V 50V 50V 50V 50V
< CONNECTOR > CN602
1-784-741-11 CONNECTOR, FFC 19P < DIODE >
D601
8-719-911-19 DIODE 1SS199-25 < FLUORESCENT INDICATOR TUBE >
FL601
< IC > IC601
< VIBRATOR > X501 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) X502 1-781-107-21 VIBRATOR, CERAMIC (16MHz) ************************************************************** A-4476-267-A PANEL BOARD, COMPLETE (AEP, UK) A-4476-269-A PANEL BOARD, COMPLETE (KR, MX, AUS) ********************** 4-232-328-01 HOLDER, FL TUBE 4-949-935-41 CUSHION (FL) < CAPACITOR > C601 C603 C605 C606 C607
1-162-306-11 1-164-159-11 1-162-306-11 1-124-261-00 1-126-382-11
CERAMIC CERAMIC CERAMIC ELECT ELECT
0.01uF 0.1uF 0.01uF 10uF 100uF
C608 C610 C614 C615 C649
1-164-159-11 1-124-261-00 1-162-286-31 1-162-286-31 1-162-306-11
CERAMIC ELECT CERAMIC CERAMIC CERAMIC
C650 C651 C652
1-162-306-11 CERAMIC 1-162-282-31 CERAMIC 1-162-282-31 CERAMIC
30% 20% 20%
16V 50V 16V 50V 16V
0.1uF 10uF 220PF 220PF 0.01uF
20% 10% 10% 30%
50V 50V 50V 50V 16V
0.01uF 100PF 100PF
30% 10% 10%
16V 50V 50V
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
30%
1-518-744-11 TUBE, FLUORESCENT INDICATOR
8-759-828-68 IC MB90M407PF-G-102-BND < RESISTOR >
R601 R602 R603 R604 R605
1-249-429-11 1-249-429-11 1-249-429-11 1-247-807-31 1-247-807-31
CARBON CARBON CARBON CARBON CARBON
10K 10K 10K 100 100
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R606 R607 R608 R616 R617
1-249-429-11 1-249-429-11 1-249-429-11 1-249-441-11 1-249-410-11
CARBON CARBON CARBON CARBON CARBON
10K 10K 10K 100K 270
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R618 R619 R620 R621 R622
1-249-413-11 1-249-414-11 1-249-416-11 1-249-417-11 1-249-418-11
CARBON CARBON CARBON CARBON CARBON
470 560 820 1K 1.2K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R623 R624 R625 R626 R627
1-249-419-11 1-249-421-11 1-249-422-11 1-249-424-11 1-249-426-11
CARBON CARBON CARBON CARBON CARBON
1.5K 2.2K 2.7K 3.9K 5.6K
5% 5% 5% 5% 5%
R628 R629 R630 R631 R632
1-249-429-11 1-249-417-11 1-249-429-11 1-249-417-11 1-249-429-11
CARBON CARBON CARBON CARBON CARBON
10K 1K 10K 1K 10K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W (AEP, UK) 1/4W 1/4W 1/4W 1/4W 1/4W
35
ST-S5 PANEL Ref. No.
SIRCS
Part No.
Description
Remark
R633 R634 R635 R636 R637
1-249-417-11 1-249-429-11 1-249-417-11 1-249-429-11 1-249-417-11
CARBON CARBON CARBON CARBON CARBON
1K 10K 1K 10K 1K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/4W
R638 R639 R677
1-249-429-11 CARBON 1-249-417-11 CARBON 1-249-417-11 CARBON
10K 1K 1K
5% 5% 5%
1/4W 1/4W 1/4W
< SWITCH > S601 S602 S603 S604 S605
1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21
SWITCH, TACTILE (DISPLAY) SWITCH, TACTILE (CLOCK/TIMER) SWITCH, TACTILE (TIMER SELECT) SWITCH, TACTILE (TUNER/BAND) SWITCH, TACTILE (TUNING +)
S606 S607 S608 S609 S610
1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21
SWITCH, TACTILE (TUMIMG –) SWITCH, TACTILE (ENTER) SWITCH, TACTILE (PRESET –) SWITCH, TACTILE (PRESET +) SWITCH, TACTILE (TUNER MEMORY)
S611 S612
1-771-410-21 SWITCH, TACTILE (STEREO/MONO) 1-771-410-21 SWITCH, TACTILE (PTY) (AEP, UK) < VIBRATOR >
X601 1-577-358-21 VIBRATOR, CERAMIC (4MHz) ************************************************************** 1-680-697-11 SIRCS BOARD ************ < CAPACITOR > C101
1-124-589-11 ELECT
47uF
20%
16V
< IC > IC101
8-749-011-05 IC GP1U28X (REMOTE CONTROL RECEIVER) < RESISTOR >
R101 1-249-401-11 CARBON 47 5% 1/4W R102 1-249-401-11 CARBON 47 5% 1/4W *********************************************************** MISCELLANEOUS ************** 2 54 55 56 57
1-773-114-11 1-757-599-11 1-757-600-11 1-757-629-11 1-757-631-11
WIRE (FLAT TYPE) (19 CORE) WIRE (FLAT TYPE) (21 CORE) WIRE (FLAT TYPE) (23 CORE) CORD (WITH CONNECTOR) 5P CORD (WITH CONNECTOR) 20P
58 60 60 61 61
1-757-630-11 1-769-940-11 1-773-004-11 1-693-529-11 1-693-531-71
CORD (WITH CONNECTOR) 19P WIRE (FLAT TYPE) (11 CORE) (KR, MX, AUS) WIRE (FLAT TYPE) (15 CORE) (AEP, UK) TUNER PACK (FM/AM) (AEP, UK) TUNER PACK (FM/AM) (MX, AUS)
61
1-693-538-11 TUNER PACK (FM/AM) (KR)
36
Ref. No.
Part No.
Description
Remark
ST-S5
MEMO
37
ST-S5
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0
Date 2001.04
Description of Revision New
