Transcript
19R-M100
1st. Edition
SERVICE MANUAL S11O219R-M100
COLOR TELEVISION
Chassis No. SN-010
POWER
VOL
CH
VIDEO IN AUDIO
MENU
19R-M100 (SREC)
MODEL
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS » » » » » » » » » »
Page ELECTRICAL SPECIFICATIONS ......................................................................................................... 1 IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2 LOCATION OF USER'S CONTROL ..................................................................................................... 4 INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5 CHASSIS LAYOUT ............................................................................................................................. 11 BLOCK DIAGRAM .............................................................................................................................. 12 SCHEMATIC DIAGRAMS ................................................................................................................... 13 PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 18 REPLACEMENT PARTS LIST ............................................................................................................ 21 PACKING OF THE SET ...................................................................................................................... 27
ELECTRICAL SPECIFICATIONS POWER INPUT .................................................... AC 120 V, 60 Hz POWER RATING ................................................................... 69 W PICTURE SIZE ........................................... 1,194cm2 (185sq inch) CONVERGENCE ............................................................. Magnetic SWEEP DEFLECTION .................................................... Magnetic FOCUS ............................................... Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ..................................... 45.75 MHz Sound IF Carrier Frequency ...................................... 41.25 MHz Color Sub-Carrier Frequency .................................... 42.17 MHz (Nominal) AUDIO POWER OUTPUT RATING ..................................................... 1 W (RMS)
SHARP CORPORATION
SPEAKER SIZE ...................................................................... 8 cm (Round) VOICE COIL IMPEDANCE ............................ 32 ohm at 400 Hz ANTENNA INPUT IMPEDANCE VHF/UHF ..................................................... 75 ohm Unbalanced TUNING RANGES VHF-Channels ............................................................... 2 thru 13 UHF-Channels ............................................................ 14 thru 69 CATV Channels ........................................................... 1 thru 125 (EIA, Channel Plan U.S.A.)
Specifications are subject to change without prior notice.
This document has been published to be used for after sales service only. 1 The contents are subject to change without notice.
19R-M100
IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value -no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. When troubleshooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.) 1. Picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
2
19R-M100
IMPORTANT SERVICE SAFETY PRECAUTION (Continued) » Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators and etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. » Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test). » Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground. » Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.
1.5k ohm 10W
0.15µF TEST PROBE
TO EXPOSED METAL PARTS
CONNECT TO KNOWN EARTH GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage and etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
19R-M100
LOCATION OF USER'S CONTROL Front Panel
POWER
–
VOL
+
CH
VIDEO IN AUDIO
MENU
VIDEO IN AUDIO IN TERMINALS SENSOR AREA FOR REMOTE CONTROL
POWER
– VOL +
CH
MENU
POWER Press → On. Press again → Off.
VOLUME UP/DOWN (+) Increases sound. (–) Decreases sound.
CHANNEL UP/DOWN (') Selects next higher channel. (" ) Selects next lower channel. • Press both at the same time to access the MAIN MENU screen.
Basic Remote Control Functions Infrared Transmitter Window POWER Press → On. Press again → Off.
INPUT Press → Switch to external video input mode. Press again → Switch to TV mode.
REMOTE KEYPAD Accesses any channel from keypad.
CHANNEL UP/DOWN ( ') Selects next higher channel. ( ") Selects next lower channel. • Moves the “ ” mark of the MENU screen.
FLASHBACK Returns to previous channel. VOLUME UP/DOWN (+) Increases sound. (–) Decreases sound. • In menu mode, changes or selects the TV adjustments.
MENU Press → Accesses MAIN MENU. Press again → Exits MAIN MENU.
MUTE Press → Mutes sound. Press again → Restores sound. • CLOSED CAPTION appears when sound is muted.
DISPLAY Press → Displays receiving channel for four seconds. Press again → Removes display. • Temporarily displays receiving channel when in Closed Caption mode. G1324SA
TV
4
19R-M100
INSTALLATION AND SERVICE INSTRUCTIONS Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic screwdrivers or TV alignment tools. (2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST 1. Connect an accurate high voltage meter between ground and anode of picture tube. 2. Operate receiver for at least 15 minutes at 120V AC line voltage, with a strong air signal or a properly tuned in test signal. 3. Enter the service mode and select the service adjustment "S03" and Bus data "01" (Y-mute on). 4. The voltage should be approximately 26.0kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.
After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows: 1. Apply 120V AC using a variac transformer for accurate input voltage. 2. Allow for warm up and adjust all customer controls for normal picture and sound. 3. Receive a good local channel. 4. Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 21.4 ±1.5 V. 5. Apply external 27.2V DC at TP653 by using an external DC supply, TV must be shut off. 6. To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen. 7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.
5
19R-M100 For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit. Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow the steps below whenever the service adjusment is required.
To enter the service mode and exit service mode. While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket. Now, the TV set is switched on and enters the service mode. To exit the service mode, turn the television off by pressing the power button.
1. Service mode. Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset function in the video adjustment menu to ensure customer control are in their proper (reset) position.
2. Service number selection. In the service mode, you will see the window screen as window 1. There are 3 adjustment categories 2DEF, 3SIGNAL, 4FIX VALUE as show in Figure A. Window 2: DEF D01 D03 D05
Window 3: SIGNAL
D02 D04 D06
DEF
S01
SIGNAL
S02 S12
S13 RETURN
RETURN Window 1: ADJUSTMENT CATEGORIES SERVICE MODE DEF SIGNAL FIX VALUE EEPROM
RETURN
RETURN
RETURN
FIX VALUE
Window 4: FIX VALUE F01
F02
F15
F16
F25
F26
NEXT F13
F14
RETURN
NEXT
PREVIOUS
RETURN PREVIOUS
Figure A: ADJUSTMENT CATEGORIES
Press CH UP/DOWN button for selection and enter by VOL UP or VOL DOWN. Press CH UP/DOWN button to select the adjustment item and VOL UP/DOWN to adjust the data number for each categories. (OSD disturbance can be erased by R/C display key) (Note: EEPROM – factory used only)
6
19R-M100 Below are the adjustments ranges and initial values for FIX VALUE category.
FIX VALUE SERVICE POSITION F01 F02 F03 F04 F05 F06 F07 F08 F09 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26
DATA
ADJUST ITEM OPTION 1 OPTION 2 E-SAVE TUNER SETUP R-TONE RD R-TONE BD B-TONE RD B-TONE BD FM LEVEL AFC GAIN G DRIVE FBT BLK SW V COMP OSD CONT SHARPNESS FLT SYS KILLER OP PRE SHOOT CORING DC REST BS START BS GAIN ABL START R/B ANGLE H BLK R H BLK L
RANGE
INITIAL VALUE
(Hex)
00-FF 00-FF 00-3F 00, 01 00-7F 00-7F 00-7F 00-7F 00-1F 00, 01 00, 0F 00, 01 00-07 00-07 00-3F 00-03 00-07 00-03 00-07 00-03 00-03 00-03 00-07 00-0F 00-07 00-07
B0 04 23 00 19 00 00 12 0C 00 0F 01 07 02 19 00 04 03 07 02 01 01 00 08 04 04
B0 04 2A 00 03 7C 00 04 0C 00 0F 01 07 01 19 00 02 00 04 02 01 01 00 08 03 00
Table - A Below are the ranges and initial values for each adjustment and in each categories.
DEF SERVICE POSITION D01 D02 D03 D04 D05 D06
ADJUST ITEM H-PHASE V-SIZE V-POSITION CC-POSITION V-LINEARITY V-S-CORRECTION
DATA RANGE
INITIAL VALUE
00-1F 00-7F 00-3F 00-FF 00-1F 00-1F
0C 40 20 1A 10 10
ADJUSTMENT CONTENTS
Must be "20" Must be "18" Must be "0C"
Table - B
SIGNAL SERVICE POSITION S01 S02
ADJUST ITEM
DATA RANGE
INITIAL VALUE
RF AGC VIDEO LEVEL
00-3F 00-07
14 03
S03
Y-MUTE
00-03
00
S04 S05 S06 S07 S08 S09 S10 S11 S12 S13
SUB BIAS R-BIAS G-BIAS B-BIAS R-DRIVE B-DRIVE CONTRAST TINT COLOR BRIGHTNESS
00-FF 00-FF 00-FF 00-FF 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F
40 00 00 00 40 40 5A 40 40 40
ADJUSTMENT CONTENTS
"01":Y-MUTE, "02":V-STOP&Y-MUTE "03":Activate color killer Must be "30"
Note: Refer to the SERVICE ADJUSTMENT for each corresponding values.
Table - C
7
19R-M100 Holding down both the Vol-up/Ch-down buttons on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2102 (IC2101). ADJUSTMENT PART REPLACED
NECESSARY
NOTES
UNNECESSARY
X
IC2001
Data is stored in IC2102 (IC2101).
X
The adjustment is needed to compensate for characteristics of parts including IC201.
IC2102 (IC2101)
X
Holding down both the Vol-up/Ch-down buttons on the TV set in the service mode for more than 2 seconds will automatically write the above initial values into IC2102 (IC2101).
CRT
X
Adjust items related to picture tube only.
IC201
Table - D
R2101 If using IC2101 If using IC2102
–
R2102
–
Table - E
8
R2103
R2104
–
–
19R-M100
Ë SERVICE ADJUSTMENT RF AGC Adjustment
White Balance Adjustment
1. Receive a good local channel. 2. Enter the service mode signal category and select the service adjustment "S01". 3. Set the data value to point where no noise or beat appears. 4. Select another channel to confirm that no noise or beat appears. Note: You have to exit the service mode first to select another channel.
1. Receive a good local channel. 2. Select the service adjustment "S12" and set the data value to "00" to set the color level to the minimun. You may skip this step, if you selected a B/W picture or monoscope. 3. Alternately adjust the service adjustment data of "S08" and "S09" until a good grey scale with normal white is obtained. 4. Select the service adjustment "S12" and reset data to obtain normal color level.
Video Level (TV Det Video Level) Adjustment
Sub-Picture Adjustment 1. Receive a good local channel. 2. Make sure the customer picture control is set to maximum. 3. Enter the service mode and select the service adjustment "S10". 4. Adjust the data value to achieve normal contrast range.
1. Receive a good local channel. 2. Enter the service mode signal category and select the service adjustment "S02". 3. Set the data value to "02" first, then adjust the data in ranges 02 ±2 step to obtain a normal contrast level.
Screen Adjustment 1. Connect to oscilloscope probe between TP855 and ground of the CRT unit. 2. Receive a good local channel. 3. Enter the service mode Signal category and set the service adjustment "S04" to step 30. Then select the service adjustment "S12" and set the data value to "00" to set the color level to the minimum level. (record the original data first). You may skip this step, if you selected a B/W picture or monoscope pattern. Set also the "S05/S06/S07" data to minimum level. 4. Select the service adjustment "S03" and set the data value to "01" to turn off the luminance signal (Y-mute). 5. Select the service adjustment "S13" and adjust the data value to obtain 2.35 volts as shown in Figure B. 6. Adjust the master screen control until the raster darkens to the point where raster is barely seen. 7. Adjust the service adjustment "S05" red, "S06" green and "S07" blue to obtain a good grey scale with normal white at low brightness level. 8. Select the service a adjustment "S03" and reset data to "00". Select the service adjustment "S12" and reset data to obtain normal color level. 9. Remove probe and reset the master screen control to obtain normal brightness range.
Sub-Tint Adjustment 1. Receive a good local channel. 2. Set the customer tint control to the center of it’s range. 3. Enter the service mode and select the service adjustment "S11". 4. Adjust "S11" data value to obtain normal fresh tones.
Sub-Color Adjustment 1. Receive a good local channel. 2. Make sure the customer color control is set to center position. 3. Enter the service mode and select the service adjustment "S12". 4. Adjust "S12" data value to obtain normal color level.
Sub-Brightness Adjustment 1. Receive a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select the service adjustment "S13". 4. Adjust "S13" data value to obtain normal brightness level.
2.35 Vdc
GND
Figure B: WAVEFORM FOR SCREEN ADJUSTMENT
9
19R-M100
Vertical-Size, V-Linearity and V-S Correction Adjustments 1. Receive a good local channel. 2. Enter the service mode DEF category and select the adjustment "D02" for Vertical Size, "D05" for VLinearity and "D06" for V-S Correction Adjustment. 3. Set in order "D05" for V-Linearity, "D06" for V-S Correction and set the data to get the best linearity. 4. Then adjust "D02" data until it become a proper vertical size.
Horizontal Position Adjustment 1. Receive a good local channel. 2. Enter the service mode DEF category and select the adjustment "D01". 3. Adjust "D01" data value to center the picture.
Vertical-Phase Adjustment 1. Receive a good local channel. 2. Enter the service mode DEF category and select the adjustment "D03". 3. Adjust "D03" bus data to get the most acceptable vertical position. Note: The step range is 20 (032) ±10 steps.
Caption Position Adjustment (Horizontal) 1. Receive a good local channel. 2. Enter the service mode DEF category and select the adjustment "D04". 3. A black text box will appear on the screen. (see Figure C. below) 4. Adjust "D04" data value to balance the text box position in the center (A=B).
A
B
Figure C.
10
19R-M100
CHASSIS LAYOUT H
ËMINI NECK
ËNORMAL NECK
G
F
E
D
C
B
A
1
2
3
4
11
5
6
19R-M100
BLOCK DIAGRAM H
G
F
E
D
C
B
A
1
2
3
4
12
5
6
19R-M100
DESCRIPTION OF SCHEMATIC DIAGRAM WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
NOTES: 1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ) 2. All resistors are 1/10 watt, unless otherwise noted. 3. All capacitors are µF, unless otherwise noted. (P=pF=µµF) 4. (G) indicates ±2% tolerance may be used. 5. indicates line isolated ground. VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. All voltages measured with 1000µ V B & W or Color signal.
å AND SHADED (
) COMPONENTS = SAFETY RELATED PARTS. ' MARK= X-RAY RELATED PARTS. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
WAVEFORMS 1.0
1.0
0.9
5.0
5.0
2.1
1.0
1.2
25
47
4.6
0.7
33
39.0
1160
220
150
133
220
1.7
0.7
1.4
105
95
105
13
MODEL 19R-M100 SCHEMATIC DIAGRAM: MAIN Unit (MINI NECK / NORMAL NECK J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
14~15
12
13
14
15
16
17
18
19
20
19R-M100
H
MODEL 19R-M100 SCHEMATIC DIAGRAM: CRT Unit (MINI NECK)
G
F
E
D
C
B
A
1
2
3
4
16
5
6
19R-M100
H
MODEL 19R-M100 SCHEMATIC DIAGRAM: CRT Unit (NORMAL NECK)
G
F
E
D
C
B
A
1
2
3
4
17
5
6
19R-M100
PRINTED WIRING BOARD ASSEMBLIES H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
18
5
6
19R-M100
H
◗✶✴✴✼
❊❈❇✸
◗I✹
◗I✻ ❇✶✴✶✵
◗✶✶✴
◗✸✵✶
❇✷✴✵
◗I✶✹
◗✶✵✷ ❇✸✵✼
❇✷✴✸
◗✷✴✶
❇✷✴✶
◗✷✴✵
❇✶✵✵
❇✶✶✴
◗✶✵✵
◗✽✺✶
◗✽✺✵
◗✶✵✶
◗✸✺✵
◗✷✴✼
❇✶✴✺
❇✶✵✷
◗✶✵✴
◗✶✴✽
◗✶✵✸
◗✸✴✵
◗✸✴✶
◗✸✴✷
❇✷✴✷
◗✷✴✹
❇✶✴✷ ◗✶✵✺
❇✸✽✶
◗✶✴✸ ◗✸✺✶
❇✶✴✶
❇✶✴✵
◗I✶✴
❇✻✼✶
◗✸✹✽
◗✸✹✺
◗✶✴✵
◗✹✹ ◗✺✹✷
◗I✵
◗✻✸✽
◗I✶
❇✻✷✷
◗I✷
◗✼✴✷
◗I✸
◗✸✵✴
◗✸✵✷
◗✼✴✻
◗✸✽✺
◗✹✵✽
◗✻✶✶
❇✻✴✽
P✸✹✵
C
❇✼✵✴
❇✼✵✵
◗✺✹✹
◗I✵✴
◗✺✶✷
❇✺✶✴
◗✸✽✸
◗✹✵✻
P✸✽✵
◗✶✴✼ ❇✶✴✼ ❇✼✴✻
◗✸✵✵ ❇✸✵✶
◗✸✶✷
◗✸✵✸
◗✸✶✸
◗I✶✶
◗I✶✵
◗✻✶✷
❇✻✵✴
◗✹✺
◗I✵✽
◗I✵✼
◗✶✸✴✸
◗✶✸✴✷
◗✶✸✴✶
◗✶✸✴✵
19
❇✷✹✵
◗I✵✶
◗✼✴✼
❇✼✴✵
❇✸✴✵ ◗✼✵✴
◗✶✴✵✶
◗I✼
◗✶✴✵✴
❇✷✹✺
◗✷✹✸
◗I✵✵
◗✶✴✸✴
◗✽✴✺ ◗I✶✷
◗✶✴✺✻
◗✶✹✴✺
◗I✵✸ ◗✶✴✺✶
◗I✶✻ ◗I✶✽
6
5
4
◗✼✴✽
◗✶✴✶✽
◗✶✴✶✴
❇✶✴✵✴
◗✶✴✵✸
◗✶✴✵✺
❇✹✵✺
◗✸✽✵
E
◗✸✶✶
◗✶✴✶✶
❇✶✴✴✵
❇✶✴✶✶ ◗✶✴✵✻
◗✶✴✵✼
◗✸✵✺ ◗✶✴✴✺
P✸✴✶ ❇✶✴✶✸
◗✶✹✴✹
◗✸✶✹ ◗✶✶✵✶
◗✶✴✸✵ ◗✶✴✻✶
❇✸✵✻ ◗✶✴✴✵
◗✸✶✵ ◗✶✴✴✶
◗✶✹✴✸
◗✶✴✷✸
❍❇✶✴✴✵
◗✶✴✶✼ ❇✶✴✴✶
❇✶✶✴✷
◗✶✹✴✷
❇✶✶✴✶ ◗✶✴✷✷
❍❇✶✵✴✶
◗✶✶✴✷
P✶✶✵✵ ❇✶✴✶✺
P✶✶✴✵ ❇✶✶✴✵
◗✶✴✻✴
◗✶✹✴✽
❇✶✴✹✵
◗✷✹✻ ◗✶✴✺✺
◗✽✶✸ ◗I✶✼ ◗✽✶✹ ◗✽✴✶ ◗✶✴✸✸
❊❈❇✺ ◗✶✴✸✹ ◗✶✴✸✼
◗✶✴✺✴
❇✶✴✺✴
◗✶✹✴✼
◗✶✹✴✵
❇✶✺✴✶
◗✶✵✴✶
◗✶✵✴✵
◗✶✴✺✵
◗✶✴✸✻ P✶✴✺✴
3
2
1
◗✻✵✵ ◗✻✶✴
◗✶✴✸✽ ◗✶✴✺✷
❊❈❇✷
◗✺✶✶
F
❇✶✴✺✵ ◗✶✴✺✹
G
◗✶✹✴✻
◗✽✴✹
◗✶✴✺✼
◗✶✴✴✽
❇✶✴✶✹
◗I✵✷
❇✶✴✶✷
◗✸✵✹
P✸✴✵
◗✼✴✶
◗I✶✸
❇✷✴✹
❇✺✷✸
◗✺✷✹
❇✶✵✸
P✷✴✵
◗✸✽✷
◗✸✽✶
◗I✽
◗✹✵✼
P✶✴✵
◗✹✵✺
◗✶✴✷
◗✶✴✶
D
◗I✶✺
◗✻✴✼
◗✶✵✹
◗I✵✺
◗✹✸
❊❈❇✹
❊❈❇✶
B
PWB-A: MAIN Unit (Chip Parts Side)
A
19R-M100
H
G
F
PWB-B: CRT Unit (Wiring Side) E
D
❊❈❇✵
❇✼✽✴
◗✼✽✶
◗✼✼✵ ◗✼✼✶
◗✼✼✺
◗✼✹✵ ◗✼✼✸
❇✼✹✶
◗✼✽✴
◗✼✺✻
◗✼✺✼
◗✼✺✽
◗✼✹✽ ◗✼✺✵
C
◗✼✽✵
❇✼✹✵ ◗✼✹✷ ✶
B
PWB-B: CRT Unit (Chip Parts Side)
A
1
2
3
4
20
5
6
19R-M100 Ref. No.
★
Part No.
Description
Code
Ref. No.
★
Part No.
Description
Code
PARTS LIST
PRINTED WIRING BOARD ASSEMBLIES
PARTS REPLACEMENT
(NOT REPLACEMENT ITEM)
Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
(MINI NECK) PWB-A DUNTKA358WEY5 PWB-B DUNTKA359WEW4
– MAIN Unit – CRT Unit
— —
(NORMAL NECK) PWB-A DUNTKA358WEY6 PWB-B DUNTKA359WEW5
– MAIN Unit – CRT Unit
— —
"HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
in USA:
PWB-A: DUNTKA358WEY5 (MINI NECK) PWB-A: DUNTKA358WEY6 (NORMAL NECK) MAIN UNIT TUNER NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. å TU51 VTUVTST5UF740 X Vhf Tuner or VTUENV56D82-1
Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
INTEGRATED CIRCUITS
★ MARK : SPARE PARTS-DELIVERY SECTION
IC201 IC351 å IC501 å IC701 å IC702 IC771
'å
' MARK : X- RAY RELATED PARTS
Ref. No.
★
Part No.
Description
Code
PICTURE TUBE (MINI NECK) 'å 'å å
V101 VB48LRH93X/*S DY601 RCiLH0201PEZZ L703 RCiLG0078PEZZ or RCiLG0014MEZZ or RCiLG0108GJZZ or RCiLG0099PEZZ LHLDW0003PEKZ LHLDW1033PEZZ PMAGF3045CEZZ PSPAG0003PEZZ QEARCA002WJZZ
J Picture Tube R Deflection Yoke R Degaussing Coil
CC AZ AM
V101 VB48KRD89X/4E DY601 RCiLHA032WJZZ L703 RCiLG0078PEZZ or RCiLG0014MEZZ or RCiLG0108GJZZ or RCiLG0099PEZZ LHLDW0003PEKZ LHLDW1033PEZZ PMAGF3046CEZZ PSPAG0003PEZZ QEARCA002WJZZ
J J J J J J
LA76843N AN7511 LA7840 TEA1507P/N1 PC817 KIA7805API
J TMPA8700CPF X PST994C-T J M24C16-BN6
AT AK AR AL AE AE AU AG
TRANSISTORS Q101 Q201 Q451 R R J R X
Wire Holder, x4 Holder Purity Magnet Spacer, x3 Grounding Strap
AB AA AG AD
Q452 Q601 å Q602 Q631 å
(NORMAL NECK) 'å 'å å
RH-iX3354CEN1 VHiAN7511//-1 VHiLA7840//-1 VHiTEA1507/-1 RH-FX0034CEZZ VHiKA7805AP-1 or VHiTA7805S/-1 IC2001 RH-iX3492CEZZQ IC2040 VHiPST994C/-1+ IC2101 VHiM24C16B/-1 or VHiBR24C16-1
J Picture Tube X Deflection Yoke R Degaussing Coil
R R J R X
Wire Holder, x4 Holder Purity Magnet Spacer, x3 Grounding Strap
Q701
CB AM
AB AA AF AD
Q702 Q751 Q752
21
VS2SC945AQ/-1+ or VS2SC3198Y/-1 VS2SC2735//1EY VS2PB709AR/-1Y or VS2SA812-M51E VS2PA1015Y+-1+ VS2SC2482//-1+ VS2SD2586//1E VS2SC945AQ/-1+ or VS2SC3198-Y-1 VSSPP04N60C-1 or VS2SK2708//1E or VSSPP07N60C-1 or VSSTP6NC60+-1 or VSSTP6NC60FP or VSSTP7NB60FP VS2SC945AQ/-1+ or VS2SC3198Y/-1 VS2SC945AQ/-1+ or VS2SC3198-Y-1 VS2SC945AQ/-1+ or VS2SC3198-Y-1
J 2SC945AQ
AB
J 2SC2735 J 2PB709AR
AC AB
J J J J
AC AD AM AB
2PA1015Y 2SC2482 2SD2586 2SC945AQ
J SPP04N60C
AH
J 2SC945AQ
AB
J 2SC945AQ
AB
J 2SC945AQ
AB
19R-M100 Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA358WEY5 (MINI NECK) PWB-A: DUNTKA358WEY6 (NORMAL NECK) MAIN UNIT (Continued) Q2201 VS2PD601AR/-1Y or VS2SC1623L61E Q2211 VS2PD601AR/-1Y or VS2SC1623L61E
J 2PD601AR
AB
J 2PD601AR
AB
★
Part No.
D752 D753
RH-DX0441CEZZY RH-DX0441CEZZY or RH-DX0110CEZZ å D757 RH-DX0048GEZZY or RH-DX0475CEZZ å D758 RH-DX0131CEZZY å VA701 RH-VX0019CEZZ or RH-VX0048CEZZ
Description
J Diode J Diode
Code AC AC
X Diode J Diode J Varistor
AC AC
DIODES D52 D101 D352 D353 D453 D455 D456 D457 D458 D459 D502 D511 D632 D641 ' å D651 ' å D653 å D661 å
D701
å
D702
å
D703
å
D704 D705 D707 D708
å å
D709 D712
å
D717 D725 D726 D740 D751
RH-EX0676GEZZY RH-EX0617GEZZY RH-DX0048GEZZY or RH-DX0475CEZZ RH-EX0644GEZZY RH-EX0616GEZZY RH-DX0048GEZZY or RH-DX0475CEZZ RH-DX0475CEZZY RH-EX0644GEZZY RH-EX0644GEZZY RH-DX0048GEZZY or RH-DX0475CEZZ RH-DX0131CEZZY RH-DX0441CEZZY RH-EX0630GEZZY RH-EX0630GEZZY VHD1SS244//-1Y RH-EX0667GEZZY RH-DX0468CEZZ or RH-DX0302CEZZ RH-DX0490CEZZY or RH-DX0154CEZZ RH-DX0490CEZZY or RH-DX0154CEZZ RH-DX0490CEZZY or RH-DX0154CEZZ RH-DX0490CEZZY or RH-DX0154CEZZ RH-DX0048GEZZY or VHD1SS244//-1 RH-DX0475CEZZY or VHD1SS244//-1 RH-DX0475CEZZY or VHD1SS244//-1 RH-DX0229CEZZ RH-DX0487CEZZY or RH-DX0302CEZZ or RH-DX0468CEZZ or VHDD1NS4///-1 RH-EX0616GEZZY RH-DX0131CEZZY RH-DX0048GEZZY or RH-DX0475CEZZ RH-DX0048GEZZY or RH-DX0441CEZZ RH-EX0611GEZZY
J Zener Diode, 32V J Zener Diode, 5.6V X Diode
AA AA
J Zener Diode, 13V J Zener Diode, 5.1V X Diode
AB AA
X J J X
Diode Zener Diode, 13V Zener Diode, 13V Diode
AB AB
J J J J J J J
Diode Diode Zener Diode, 9.1V Zener Diode, 9.1V Diode Zener Diode, 27V Diode
AC AC AA AA AB AA AE
J Diode
AC
J Diode
AC
J Diode
AC
J Diode
AC
PACKAGED CIRCUIT å
PR702 RMPTP0092CEZZ X801 RCRSAA010WJZZ or RCRSB0205CEZZ
J Packaged Circuit X Crystal
AH
FILTER AND COILS CF2040 RFiLA0099CEZZ+ or RFiLC0121GEZZ L50 VP-DF150K0000Y L201 VP-XF1R2K0000Y L202 VP-XF1R2K0000Y L203 VP-XF220K0000Y L204 RCiLi0632CEZZ L301 VP-XF150K0000Y å L701 RCiLF0078PEZZ or RCiLF0069PEZZ å L705 RCiLP0179CEZZ+ L706 RCiLP0197CEZZ L2040 RCiLB0131CEZZ SF201 RFiLC0441CEZZ
X Ceramic Filter X J J J J X J
Peaking 15µH Peaking 1.2µH Peaking 1.2µH Peaking 22µH If Coil Peaking 15µH Coil
J J J J
Coil Coil Oscillation Coil SAW Filter
AB AB AB AE AF AD AE AE AH
TRANSFORMERS å
T601
'å å
T602 T702
RTRNZ0731CEZZ or RTRNZ0026PEZZ RTRNF0213PEZZ RTRNW0009PEZZ or RTRNW0003PEZZ
J Transformer
AG
R H-Volt Transformer R Transformer
AY AL
CONTROL R738
X Diode
RVR-M4588CEZZ+ or RVR-M4336CEZZ
J 22k 130V Adj.
AC
CAPACITORS [EL.··· Electrolytic, M-Poly..··· Metalized Polypro Film] C51 VCEA0A1AW337M+ J 330 10V EL. C53 VCEA0A1HW105M+ J 1.0 50V EL. C54 VCEA0A1HW475M+ J 4.7 50V EL. C55 VCEA0A1AW107M+ J 100 10V EL. C101 VCEA0A1CW476M+ J 47 16V EL. C201 VCKYCY1HF103ZY J 0.01 50V Ceramic C202 VCKYCY1HF103ZY J 0.01 50V Ceramic C203 VCKYCY1HF103ZY J 0.01 50V Ceramic C204 VCQYTA1HM223K+ J 0.022 50V Mylar C205 VCKYPA1HB103K+ J 0.01 50V Ceramic C206 VCKYCY1HB102KY J 1000p 50V Ceramic C207 VCEA0A1CW476M+ J 47 16V EL. C208 VCKYCY1HF103ZY J 0.01 50V Ceramic C209 VCEA0A1HW105M+ J 1.0 50V EL. C210 VCEA0A1HW474M+ J 0.47 50V EL. C212 VCEA0A1HW474M+ J 0.47 50V EL. C220 VCKYCY1CB104KY J 0.1 16V Ceramic C301 VCCCCY1HH220JY J 22p 50V Ceramic C302 VCKYCY1HB102KY J 1000p 50V Ceramic C304 VCCCCY1HH220JY J 22p 50V Ceramic C305 VCKYCY1HB103KY J 0.01 50V Ceramic C306 VCQYTA1HM103K+ J 0.01 50V Mylar
X Diode X Diode J Diode J Diode
AF AC
J Zener Diode, 5.6V J Diode X Diode
AA AC
X Diode J Zener Diode, 5.1V
AA
22
AC AB AB AB AB AA AA AA AB AA AA AB AA AB AB AB AB AA AA AA AA AB
19R-M100 Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKA358WEY5 (MINI NECK) PWB-A: DUNTKA358WEY6 (NORMAL NECK) MAIN UNIT (Continued) C354 C356 C357 C358 C361 C401 C411 C412 C414 C416 C418 C421 C451 C454 C455 C456 C509 C510 C512 C513 C514 C515 C516 C517 C520 C530 C531 C606 C607 ' å C610 C610 C612 C633 C634 C635 C636 C637 C652 C653 C661 C662 å C701
C702 C703 C705 å C706
å å
C717 C723 C725 C726 C727
VCEA0A1HW225M+ VCKYCY1HB332KY VCEA0A1HW106M+ VCEA0A1HW106M+ VCEA0A1CW227M+ VCCCCY1HH470JY VCEA0A1AW108M+ VCKYCY1HB103KY VCEA0A1HW225M+ VCEA0A1HW105M+ VCKYCY1HB103KY VCEA0A1HW106M+ VCQYTA1HM563K+ VCEA0A1HW475M+ VCEA0A1CW226M+ VCEA0A1HW475M+ VCKYPA2HB102K+ VCEA0A1VW477M VCFYSA1JB224J+ VCFYSA1JB473J+ VCEA0A1EW477M VCEA0A1HW475M+ VCKYCY1HB222KY VCEA0A1CW226M+ VCEA0A1HW107M+ VCFYFA1HA334J+ VCFYFA1HA564J+ VCKYPA2HB561K+ VCKYPA1HB472K+ VCFPVC3ZA772H
J J J J J J J J J J J J J J J J J J J J J J J J J J J J X J
VCFPFD3ZA802H
X
VCFPVC2DB474J VCEA0A1AW337M+ VCKYCY1HF103ZY VCEA0A1HW105M+ VCQYTA1HM153K+ VCEA0A1CW476M+ VCEA0A1HW475M+ VCEA0A1HW105M+ VCKYPA2HB152K+ VCEA0A1CW477M+ RC-FZA018WJZZ or RC-FZ008SGEZZ or RC-FZ016SCEZZ or RC-FZ028SCEZZ or RC-FZ029CUMZZ or RC-FZ036SCEZZ RC-KZ0029CEZZ+ RC-KZ0029CEZZ RC-EZA070WJZZ RC-KZ0092GEZZ or RC-KZ021SCEZZ or RC-KZA039WJZZ or RC-KZ0106GEZZ or RC-KZ009SCEZZ VCKYPA2HB472K+ RC-EZA069WJZZ RC-EZ0776CEZZ VCKYPH3DB561K VCKYPA2HB472K+
J J J J J J J J J J X
2.2 50V EL. 3300p 50V Ceramic 10 50V EL. 10 50V EL. 220 16V EL. 47p 50V Ceramic 1000 10V EL. 0.01 50V Ceramic 2.2 50V EL. 1.0 50V EL. 0.01 50V Ceramic 10 50V EL. 0.056 50V Mylar 4.7 50V EL. 22 16V EL. 4.7 50V EL. 1000p 500V Ceramic 470 35V EL. 0.22 63V Mylar 0.047 63V Mylar 470 25V EL. 4.7 50V EL. 2200p 50V Ceramic 22 16V EL. 100 50V EL. 0.33 50V Mylar 0.56 50V Mylar 560p 500V Ceramic 4700p 50V Ceramic 7700p 1.8kV M-Poly. (MINI NECK) 8000p 1.8kV M-Poly. (NORMAL NECK) 0.47 200V M-Poly. 330 10V EL. 0.01 50V Ceramic 1.0 50V EL. 0.015 50V Mylar 47 16V EL. 4.7 50V EL. 1.0 50V EL. 1500p 500V Ceramic 470 16V EL. 0.1
X 0.01 AC250V Ceramic J 0.01 AC250V Ceramic X J 0.0033 AC250V Ceramic
J X X J J
4700p 33 100 560p 4700p
500V 160V 160V 2kV 500V
Ceramic EL. EL. Ceramic Ceramic
å å
AB AA AB AB AC AA AC AA AB AB AA AB AB AB AB AB AA AB AD AC AD AB AA AB AB AB AB AA
C730 C731 C732 C735 C737 C738 C739 C740 C743 C750 C752 C753 C754 C758 C759 C760 C771 C772 C783 C801 C802 C807 C808 C809 C811 C812 C901 C905 C2001 C2002 C2040 C2041 C2060 C2061 C2062 C2201 C2202 C2601 C2602
AD
AE AC AA AB AA AB AB AB AA AC
★
Part No. VCEA0A1CW108M VCEA0A1EW227M+ VCKYPA1HF103Z+ VCCCPA1HH680J+ VCEA0A1EW226M+ RC-KZ0040CEZZ or RC-KZ0340CEZZ VCEA0A1HW104M+ VCEA0A1EW476M+ VCKYPH3DB561K VCKYPA1HF103Z+ VCEA0A1CW476M+ VCKYPH3DB561K VCEA0A1CW476M+ VCEA0A2EW106M VCKYPA2HB102K+ VCEA0A1CW108M VCEA0A1CW476M+ VCEA0A1CW476M+ VCQYTA1HM103K+ VCCCCY1HH180JY VCEA0A1CW106M+ VCKYCY1EF104ZY VCEA0A1CW106M+ VCEA0A1HW105M+ VCKYCY1CB473KY VCEA0A1HW474M+ VCEA0A1HW105M+ VCEA0A1HW106M+ VCCCCY1HH101JY VCCCCY1HH101JY VCEA0A1AW107M+ VCEA0A1HW105M+ VCKYCY1CB104KY VCKYCY1HB222KY VCEA0A1AW107M+ VCKYCY1HB682KY VCCCCY1HH560JY VCEA0A0JW107M+ VCCCCY1HH101JY
Description
Code
J J J X J J
1000 220 0.01 68p 22 820p
16V 25V 50V 50V 25V 2kV
EL. EL. Ceramic Ceramic EL. Ceramic
AD AB AA
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
0.1 47 560p 0.01 47 560p 47 10 1000p 1000 47 47 0.01 18p 10 0.1 10 1.0 0.047 0.47 1.0 10 100p 100p 100 1.0 0.1 2200p 100 6800p 56p 100 100p
50V 25V 2kV 50V 16V 2kV 16V 250V 500V 16V 16V 16V 50V 50V 16V 25V 16V 50V 16V 50V 50V 50V 50V 50V 10V 50V 16V 50V 10V 50V 50V 6.3V 50V
EL. EL. Ceramic Ceramic EL. Ceramic EL. EL. Ceramic EL. EL. EL. Mylar Ceramic EL. Ceramic EL. EL. Ceramic EL. EL. EL. Ceramic Ceramic EL. EL. Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic
AB AB AC AA AB AC AB AD AA AD AB AB AB AA AB AA AB AB AA AB AB AB AA AA AB AB AB AA AB AA AB AB AA
AB AD
RESISTORS RJ2 RJ7 RJ8 RJ9 RJ10 RJ12 RJ16 RJ18 RJ19 RJ20 RJ21 å R53 R54 R55 R56 R57 R101 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R215 R220
AC AC
AB AC AB
23
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film] VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-VV3LB223J J 22k 3.0W M-Ox. VRS-CY1JF101JY J 100 1/16W M-Ox. VRS-CY1JF101JY J 100 1/16W M-Ox. VRS-CY1JF823JY J 82k 1/16W M-Ox. VRD-RA2BE563JY J 56k 1/8W Carbon VRD-RA2BE152JY J 1.5k 1/8W Carbon VRS-CY1JF221JY J 220 1/16W M-Ox. VRS-CY1JF122JY J 1.2k 1/16W M-Ox. VRS-CY1JF682JY J 6.8k 1/16W M-Ox. VRS-CY1JF270JY J 27 1/16W M-Ox. VRD-RA2BE680JY J 68 1/8W Carbon VRD-RA2EE151JY X 150 1/4W Carbon VRD-RA2BE223JY J 22k 1/8W Carbon VRS-CY1JF332JY J 3.3k 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF104JY J 100k 1/16W M-Ox. VRS-CY1JF104JY J 100k 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF331JY J 330 1/16W M-Ox.
AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
19R-M100 Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKA358WEY5 (MINI NECK) PWB-A: DUNTKA358WEY6 (NORMAL NECK) MAIN UNIT (Continued) R301 R302 R353 R354 R355 R357 R401 R402 R403 R404 R411 R412 R413 R414 R421 å R451 R453 R454 R455 R456 R457 R458 R460 R461 R462 R495 R512 R513 R514 R515 R516 R517 R518 R519 R520 R520 R522 R523 R525 R527 R528 R529 å R604 R605 R606 å R607 å R608 å R609 R610 å R611 R622 R623 R624 R634 R635 R636 å R641 ' å R651 å R653 ' å R654 å R655 å R659 R659 å 'å å
R661 R662 R702
VRS-CY1JF102JY J 1.0k 1/16W M-Ox. VRS-CY1JF152JY J 1.5k 1/16W M-Ox. VRD-RA2BE683JY X 68k 1/8W Carbon VRS-CY1JF103JY J 10k 1/16W M-Ox. VRD-RA2BE223JY J 22k 1/8W Carbon VRS-CY1JF822JY J 8.2k 1/16W M-Ox. VRS-CY1JF101JY J 100 1/16W M-Ox. VRS-CY1JF101JY J 100 1/16W M-Ox. VRS-CY1JF101JY J 100 1/16W M-Ox. VRD-RA2BE102JY J 1.0k 1/8W Carbon VRS-CY1JF684JY J 680k 1/16W M-Ox. VRS-CY1JF391JY J 390 1/16W M-Ox. VRS-CY1JF102JY J 1.0k 1/16W M-Ox. VRS-CY1JF000JY J 00 1/16W M-Ox. VRS-CY1JF223JY J 22k 1/16W M-Ox. VRS-SV2HC103J J 10k 1/2W M-Ox. VRD-RA2BE152JY J 1.5k 1/8W Carbon VRD-RA2EE334JY J 330k 1/4W Carbon VRD-RA2BE392JY J 3.9k 1/8W Carbon VRS-CY1JF103JY J 10k 1/16W M-Ox. VRD-RA2BE102JY J 1.0k 1/8W Carbon VRD-RA2EE334JY J 330k 1/4W Carbon VRD-RA2BE152JY J 1.5k 1/8W Carbon VRS-CY1JF184JY J 180k 1/16W M-Ox. VRS-CY1JF273JY J 27k 1/16W M-Ox. VRS-VV3DB820J J 82 2W M-Ox. VRD-RM2HD102JY J 1.0k 1/2W Carbon VRD-RM2HD102JY J 1.0k 1/2W Carbon VRD-RM2HD1R0JY J 1.0 1/2W Carbon VRS-VV3AB391J J 390 1W M-Ox. VRS-CY1JF153JY J 15k 1/16W M-Ox. VRS-CY1JF102JY J 1.0k 1/16W M-Ox. VRS-CY1JF333JY J 33k 1/16W M-Ox. VRS-CY1JF103JY J 10k 1/16W M-Ox. VRD-RM2HD1R5JY J 1.5 1/2W Carbon (MINI NECK) VRD-RM2HD1R2JY J 1.2 1/2W Carbon (NORMAL NECK) VRD-RA2BE102JY J 1.0k 1/8W Carbon VRD-RA2BE562JY J 5.6k 1/8W Carbon VRD-RA2BE272JY J 2.7k 1/8W Carbon VRD-RA2BE223JY J 22k 1/8W Carbon (MINI NECK) VRD-RA2BE272JY J 2.7k 1/8W Carbon VRD-RA2BE472JY J 4.7k 1/8W Carbon VRS-VV3DB682J J 6.8k 2W M-Ox. VRD-RA2BE121JY X 120 1/8W Carbon VRD-RA2BE102JY J 1.0k 1/8W Carbon VRS-VV3DB682J J 6.8k 2W M-Ox. VRS-VV3DB391J J 390 2W M-Ox. VRS-VV3AB562J J 5.6k 1W M-Ox. VRD-RM2HD220JY J 22 1/2W Carbon VRS-KA3HG3R3K J 3.3 5W M-Ox. VRS-CY1JF222JY J 2.2k 1/16W M-Ox. VRS-CY1JF103JY J 10k 1/16W M-Ox. VRN-RA2BK472FY J 4.7k 1/8W M-Film VRD-RM2HD121JY J 120 1/2W Carbon VRS-CY1JF332JY J 3.3k 1/16W M-Ox. VRD-RA2EE221JY J 220 1/4W Carbon VRS-VV3AB682J J 6.8k 1W M-Ox. VRD-RM2HD270JY J 27 1/2W Carbon VRS-CY1JF000JY J 00 1/16W M-Ox. VRD-RA2BE154JY X 150k 1/8W Carbon VRS-CY1JF103JY J 10k 1/16W M-Ox. VRN-VV3AB2R2J J 2.2 1W M-Film (MINI NECK) VRN-VV3ABR82J J 0.82 1W M-Film (NORMAL NECK) VRN-VV3ABR47J J 0.47 1W M-Film VRD-RA2BE102GY J 1.0k 1/8W Carbon RR-DZ0049CEZZY J 3.9M 1/2W Carbon
AA AA
R703 R705 R706 R707 R708 R710 R711 R712 R713 R715 R716 å R721 R722 R723 R725 R733 R736 R739 R740 R741 R742 R743 R751 R752 R755 å R758 å R773 å R774 R801 R807 R808 R809 R810 R901 R902 R906 R925 R961 R962 R2001 R2002 R2006 R2008 R2009 R2010 R2012 R2016 R2018 R2020 R2022 R2023 R2024 R2025 R2026 R2027 R2028 R2029 R2032 R2033 R2034 R2040 R2041 R2042 R2043 R2044 R2045 R2047 R2048 R2049 R2060 R2061 å
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB
24
Part No. or RR-HZ0048CEZZ or RR-UB2HG395K VRW-KP3HC1R8K VRN-VV3ABR39J VRN-VV3ABR39J VRD-RM2HD270JY VRS-CY1JF102JY VRS-SV2HC102J VRS-CY1JF334JY VRD-RA2BE100JY VRS-SV2HC122J VRD-RA2BE150JY VRS-VV3AB121J VRD-RM2HD124JY VRS-CY1JF225JY VRS-CY1JF000JY VRS-SV2HC821J VRD-RA2EE394JY VRD-RM2HD184JY VRD-RM2HD332JY VRD-RM2HD470JY VRN-RA2BK682FY VRD-RM2HD561JY VRD-RM2HD681JY VRD-RA2BE821JY VRD-RA2BE562JY VRD-RM2HD151JY VRS-SV2HC100J VRS-VV3LB270J VRS-VV3LB680J VRD-RM2HD470JY VRS-CY1JF272JY VRS-CY1JF222JY VRS-CY1JF223JY VRS-CY1JF223JY VRD-RA2BE101JY VRS-CY1JF750JY VRS-CY1JF102JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF472JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF103JY VRS-CY1JF223JY VRS-CY1JF103JY VRS-CY1JF223JY VRS-CY1JF333JY VRD-RA2BE223JY VRD-RA2BE682JY VRD-RA2BE682JY VRD-RA2BE682JY VRD-RA2BE682JY VRS-CY1JF102JY VRS-CY1JF103JY VRD-RA2BE471JY VRS-CY1JF684JY VRS-CY1JF684JY VRS-CY1JF102JY VRS-CY1JF333JY VRD-RA2BE101JY VRD-RA2BE101JY VRS-CY1JF683JY VRS-CY1JF101JY VRS-CY1JF221JY VRS-CY1JF562JY VRS-CY1JF333JY VRS-CY1JF221JY VRS-CY1JF562JY
★
J J J J J J J J J J J J X J J J J J J X J J J J J J J J J J J J J X J J J J J J J J J J J J J J J J J X X X X J J X J J J J X X J J J J J J J
Description
1.8 5W 0.39 1W 0.39 1W 27 1/2W 1.0k 1/16W 1.0k 1/2W 330k 1/16W 10 1/8W 1.2k 1/2W 15 1/8W 120 1W 120k 1/2W 2.2M 1/16W 00 1/16W 820 1/2W 390k 1/4W 180k 1/2W 3.3k 1/2W 47 1/2W 6.8k 1/8W 560 1/2W 680 1/2W 820 1/8W 5.6k 1/8W 150 1/2W 10 1/2W 27 3.0W 68 3.0W 47 1/2W 2.7k 1/16W 2.2k 1/16W 22k 1/16W 22k 1/16W 100 1/8W 75 1/16W 1.0k 1/16W 100k 1/16W 100 1/16W 100 1/16W 1.0k 1/16W 10k 1/16W 10k 1/16W 4.7k 1/16W 1.0k 1/16W 1.0k 1/16W 10k 1/16W 22k 1/16W 10k 1/16W 22k 1/16W 33k 1/16W 22k 1/8W 6.8k 1/8W 6.8k 1/8W 6.8k 1/8W 6.8k 1/8W 1.0k 1/16W 10k 1/16W 470 1/8W 680k 1/16W 680k 1/16W 1.0k 1/16W 33k 1/16W 100 1/8W 100 1/8W 68k 1/16W 100 1/16W 220 1/16W 5.6k 1/16W 33k 1/16W 220 1/16W 5.6k 1/16W
Cement M-Film M-Film Carbon M-Ox. M-Ox. M-Ox. Carbon M-Ox. Carbon M-Ox. Carbon M-Ox. M-Ox. M-Ox. Carbon Carbon Carbon Carbon M-Film Carbon Carbon Carbon Carbon Carbon M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon Carbon Carbon Carbon M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox.
Code
AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
AA AA AA AA AA AA AA AA AA AA AA AA AA
19R-M100 Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA358WEY5 (MINI NECK) PWB-A: DUNTKA358WEY6 (NORMAL NECK) MAIN UNIT (Continued) R2062 R2063 R2065 R2066 R2067 R2068 R2070 R2072 R2101 R2102 R2201 R2202 R2203 R2211 R2212 R2213 R2401 R2402 R2403 R2404 R2501 R2503 R2504 R2505 R2506 R2507 R2508 R2509 R2601 R2603 R2605 R2607
VRS-CY1JF183JY VRS-CY1JF222JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRD-RA2BE103JY VRD-RA2BE473JY VRS-CY1JF332JY VRD-RA2BE222JY VRS-CY1JF682JY VRD-RA2BE223JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF123JY VRS-CY1JF273JY VRS-CY1JF123JY VRS-CY1JF563JY VRS-CY1JF563JY VRS-CY1JF823JY VRS-CY1JF153JY VRS-CY1JF272JY VRD-RA2BE100JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY
J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J
18k 2.2k 00 10k 10k 10k 10k 10k 100 100 10k 47k 3.3k 2.2k 6.8k 22k 100 100 100 100 12k 27k 12k 56k 56k 82k 15k 2.7k 10 00 00 00
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/8W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W
M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. Carbon M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox.
P751 QPLGN0461CEZZ P2001 QPLGN0561CEZZ RMC2601 RRMCU0222CEZZ JA409 RBLN-0047CEZZY RDA501 PRDAR0297PEFW RDA602 PRDAR0216PEFW RDA701 PRDAR0026PEFW LX-BZ3100CEFD LX-BZ3100CEFD LX-BZ3100CEFD
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
SWITCHES S2501 QSW-K0003AJZZ+ or QSW-K0079GEZZ S2502 QSW-K0003AJZZ+ or QSW-K0079GEZZ S2503 QSW-K0003AJZZ+ or QSW-K0079GEZZ S2504 QSW-K0003AJZZ+ or QSW-K0079GEZZ S2505 QSW-K0003AJZZ+ or QSW-K0079GEZZ
J Power
AB
J VOL-Down
AB
J VOL-Up
AB
J CH-Down
AB
J CH-Up
AB
MISCELLANEOUS PARTS å å
RY701 RRLYJ0081CEZZ F701 QFS-B4023CEZZ or QFS-B4021GEZZ FB351 RBLN-0091GEZZY FB601 RBLN-0047CEZZY FB2002RBLN-0091GEZZY FH701 QFSHD1013CEZZ+ FH702 QFSHD1014CEZZ+ J903 QJAKE0211CE09 or QJAKE0159CEZZ J905 QJAKE0211CE04 or QJAKE0158CEZZ P302 QPLGN0261CEZZ P401 QPLGN0561CEZZ P601 QPLGN0660CEZZ P651 QPLGN0361CEZZ P701 QPLGN0260CEZZ
J Relay J Fuse, 4A/125V
AL AC
J J J J J J
Ferrite Bead Ferrite Bead Ferrite Bead Fuse Holder Fuse Holder Jack, Audio-In
AB AB AB AC AC AD
J Jack, Video-In
AD
J J J J J
AB AB AC AB AC
Plug, 2-pin(S) Plug, 5-pin(GBM) Plug, 6-pin(K) Plug, 3-pin(TP651-3) Plug, 2-pin(M)
Part No.
25
★
Description
Code
J J J J R R R J J J
Plug, 4-pin(YBN) Plug, 5-pin(TP2001-5) R/C Receiver Balun Heat Sink, for IC501 Heat Sink, for Q602 Heat Sink, for Q701 Screw Screw Screw
AB AB AL AB AD AE AD AA AA AA
19R-M100 Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-B: DUNTKA359WEW4 (MINI NECK) PWB-B: DUNTKA359WEW5 (NORMAL NECK) CRT UNIT
Q854 Q856 Q881
RH-TX0110BMZZ+ or VS2SC22290/1E RH-TX0110BMZZ+ or VS2SC22290/1E RH-TX0110BMZZ+ or VS2SC22290/1E VS2PA1015Y+-1+ or VS2SA1015-Y-1
å
J
TX0110BM
AC
J
TX0110BM
AC
J
TX0110BM
AC
J
2PA1015Y
AC
DIODES D882 D885
RH-DX0048GEZZY RH-DX0475CEZZY
L852
VP-MK820K0000+
X Diode X Diode
COIL J Peaking 82µH
AB
CAPACITORS C851 C852 C853 C854 C883
[EL.··· Electrolytic] VCCCCY1HH151JY J 150p VCCCCY1HH151JY J 150p VCCSPA1HL151J+ J 150p RC-KZ0029CEZZ+ X 0.01 or RC-KZ0160GEZZ VCEA0A1CW336M+ J 33
50V 50V 50V 1.4kV
Ceramic Ceramic Ceramic Ceramic
AA AA AA
16V
EL.
AB
ACC701 QACCD3064CESA or QACCD3060CESA or QACCD3090CESA SP1 VSP0080PBQ9YA or VSP0080PBP7YA or VSP0080PBP8YA QCNW-0167MEZZ QCNW-2046PEZZ QCNW-2160PEZZ LHLDK0014PEZZ LHLDZ0063PEZZ TLABM1829PEZZ TLABN0001PEZZ LX-TZA003WJFD LX-WZ0003PEFD XTASD40P20000 LX-TZ0019PEFD TCAUS0010PEZZ
R851 R852 R853 å R857 R858 R859 R860 R861 å R865 R866 R867 R868 R869 å R873 R874 R881 R882 R883 R884 R886 R887 R890 R891
J AC Cord(AC120V/60Hz)
AM
J Speaker, 32 ohm
AH
J R R R R R R J R J R R
AE AF AG AD AD AB AD AF AB AA
Connecting Cord Connecting Cord Connecting Cord AC Cord Holder Anode Clamp Holder Model Label Serial No. Label CRT Screw, x4 CRT Washer, x4 Screw, x4 Screw, x4 Caution Card
RRMCG1324CESA TiNS-A205WJZZ TGAN-0018PEZZ
J Infrared R/C Unit X Operation Manual R Guarantee Card
AB
AT AD
PACKING PARTS (NOT REPLACEMENT ITEM)
AA
SPAKCA150WJZZ SPAKP0098PEZZ SPAKXA076WJZZ SSAKA0001PEZZ
AA AA AA AA AA
– R – R
Packing Case Wrapping Paper Buffer Material Polyethylene Bag
1 1-1 1-2 1-3 1-4
CCABAA075WEV0 Not Available GCOVAA107WJSA HBDGB0019PESB JBTN-A042WJKA
2
GCABBA042WJKA
X – X R X
Cabinet Front Cabinet — Cover for R/C Badge, "SHARP" AD Button(Power, Vol-up/down, CH-up/down) X Rear Cabinet
2
1 1-1
AA AA AA AA AA
J Plug, 5-pin(GBN) J Plug, 4-pin(YBN) R Socket, 11-pin (NORMAL NECK)
AB AB AF
J Socket, 9-pin (MINI NECK)
AG
— AG — AA
CABINET PARTS
AA AA AA AA AA AA AA AA AA AA AA
MISCELLANEOUS PARTS P851 QPLGN0561CEZZ P852 QPLGN0461CEZZ SC851 QSOCV0016PEZZ or QSOCV0933CEZZ SC852 QSOCV0841CEZZ or QSOCV0840CEZZ
Code
SUPPLIED ACCESORRIES
RESISTORS [M-Ox.··· Metal Oxide] VRS-CY1JF470JY J 47 1/16W M-Ox. (NORMAL NECK) VRD-RA2BE181JY J 180 1/8W Carbon VRS-CY1JF121JY J 120 1/16W M-Ox. VRS-VV3AB123J J 12k 1W M-Ox. VRD-RM2HD332JY J 3.3k 1/2W Carbon VRS-CY1JF470JY J 47 1/16W M-Ox. (NORMAL NECK) VRD-RA2BE181JY J 180 1/8W Carbon VRS-CY1JF121JY J 120 1/16W M-Ox. VRS-VV3AB123J J 12k 1W M-Ox. VRD-RM2HD332JY J 3.3k 1/2W Carbon VRS-CY1JF470JY J 47 1/16W M-Ox. VRS-CY1JF181JY J 180 1/16W M-Ox. VRS-CY1JF121JY J 120 1/16W M-Ox. VRS-VV3AB123J J 12k 1W M-Ox. VRD-RM2HD332JY J 3.3k 1/2W Carbon VRS-CY1JF561JY J 560 1/16W M-Ox. VRS-CY1JF391JY J 390 1/16W M-Ox. VRD-RA2BE561JY X 560 1/8W Carbon VRS-CY1JF152JY J 1.5k 1/16W M-Ox. VRS-CY1JF821JY J 820 1/16W M-Ox. VRD-RA2BE470JY J 47 1/8W Carbon VRS-CY1JF470JY J 47 1/16W M-Ox. (MINI NECK) VRS-CY1JF470JY J 47 1/16W M-Ox. (MINI NECK)
Description
MISCELLANEOUS PARTS
TRANSISTORS Q852
★
Part No.
1-3
26
1-2
1-4
19R-M100 Ref. No.
★
Part No.
★
Description
Code No. Part No. PACKING OFRef. THE SET
Description
★ Polyethylene Bag
Operation Manual Infrared R/C Unit ★ Batteries ★ Wrapping Paper
★ Buffer Material
FRONT
★ Packing Case
Use tape to fix the top side of packing case.
REAR
Use 10 staples to fix the bottom side of packing case.
★ MARK : Not replacement items.
27
Code
19R-M100 Ref. No.
Part No.
★
Description
Code
Ref. No.
★
Part No.
Description
Code
COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION AV Systems Group Quality, Reliability Control Center Yaita, Tochigi 329-2193, Japan
TQ0000-S Jul. 2002 Printed in Japan
D SEM P SREC
MI. KD
28
