Service Manual Ergo 300 (usb+ps2)

Transcript

Service Manual Ergo 300 (USB+PS2) Service Manual Ergo 300(USB+PS/2) Table of Contents Chapter 1. Introduction .....................................................................................................................2 a. System Requirements............................................................................................... 2 b. Support Windows..................................................................................................... 2 Chapter 2. Troubleshooting...............................................................................................................3 Chapter3. Testing Procedures……………………………………………………………..4 a.Testing Flow Chart……………………………………………………………………4 b.Check USB cable………………………………………………………………….5 c.Check Mouse Cursor………………………………..……………………………..6 d.Check Mouse Buttons………………………………..………………………………7 Chapter 4. Removal and Replacement……………………………………………………………9 Chapter 5. Parts list ....................................................................................................................... 110 Chapter 6. Tools ............................................................................................................................ 110 Version 1.0 Page 1 Service Manual Ergo 300(USB+PS/2) Chapter 1. Introduction a. System Requirements ♦ ♦ ♦ ♦ ♦ b. IBM PC Pentium 233 compatible or higher Windows XP/Me/2003/98SE or Mac OS or later Available USB port Available PS2 port(for USB & PS/2 Version) CD/DVD-ROM drive for software installation Support Windows ♦ XP/Me/2003/98SE and Mac OS Version 1.0 Page 2 Service Manual Ergo 300(USB+PS/2) Chapter 2.Troubleshooting Item Condition Probable Reasons Solutions 1. Mouse can’t work 1. Cursor can’t work 1. USB cable or mouse Change USB cable or failed mouse PCBA 2. Button can’t work 1.Press button no respond 1. Mouse PCBA or buttons failed Change mouse PCBA or buttons 1. Sensor failed Change PCBA or sensor 3. Cursor can’t 1. Cursor can’t move smoothly move smoothly Version 1.0 Page 3 Service Manual Ergo 300(USB+PS/2) Chapter 3. Testing Procedures a. Testing flow chart START F Check USB cable Replace USB cable T F Replace PCBA Check Mouse Cursor Mouse T F Replace Mouse PCBA or buttons Check Mouse buttons T END Version 1.0 Page 4 Service Manual Ergo 300(USB+PS/2) b.Check USB cable when mouse can not work. When mouse can not work please use a good USB cable to check if the mouse can function or not ,if mouse can function that means the old USB cable is failed so please replace a new USB cable. USB cable Version 1.0 Page 5 Service Manual Ergo 300(USB+PS/2) c.Check Mouse cursor If the cursor can not still move after replacing USB cable , please replace mouse PCBA . If cursor can not move smoothly,please replace sensor(U2). Mouse PCBA Sensor Version 1.0 Page 6 Service Manual Ergo 300(USB+PS/2) d.Check mouse buttons If the mouse buttons do not function, please replace S1/S2/S3/S4/S5 or mouse PCBA . Version 1.0 Page 7 Service Manual Chapter 4. Ergo 300(USB+PS/2) Removal and Replacement Step Description 1. Take plate from mouse To disassemble the mouse, you have to take the plate apart. 2. Loose screws Using screwdriver to loose 3 screws as red circle and then you can take the upper cover apart. Picture Version 1.0 Page 8 Service Manual 3. Take apart PCBA Ergo 300(USB+PS/2) Disconnect USB cable and then pick PCBA directly. The PCBA is the most important part of mouse. Version 1.0 Page 9 Service Manual Ergo 300(USB+PS/2) Chapter 5. Part list Item Parts number Description 1 20000645101 Mouse PCBA 2 10300168000 Sensor 3 15160829101 USB cable 4 10900001200 Buttons S1/S3 5 10900075000 Button S2 6 10900129100 Buttons S4/S5 U2 Item number:31010694100 Chapter 6. Tools 1. Screwdriver cross 2. Soldering iron Version 1.0 Page 10