Transcript
Service Manual
Ergo R5000
Service Manual
Ergo R5000
Table of Contents Chapter 1. Introduction .....................................................................................................................2 a. System Requirements............................................................................................... 2 b. Support Windows..................................................................................................... 2
Chapter 2. Troubleshooting...............................................................................................................3 Chapter3. Testing Procedures……………………………………………………………..4 a.Testing Flow Chart……………………………………………………………………4 b.Check Receiver ………………………………………………………………….6 c.Check Mouse LED……………………………………..……………………………..7 d.Check Mouse Button………………………………..………………………………8 e.Check Cursor…………………………………………………………………………9 f.Check Connecting between PC and Mouse…………………………………………10 g.Can not recharge……………………………………………………………………11
Chapter 4. Removal and Replacement............................................................................................ 12 Chapter 5. Parts list .........................................................................................................................15 Chapter 6. Tools ..............................................................................................................................15
Version 1.0
Page 1
Service Manual
Ergo R5000
Chapter 1. Introduction a.
System Requirements ♦ IBM PC Pentium 233 compatible or higher ♦ Windows XP/Me/2000/98 ♦ Available USB port
b.
Support Windows ♦ XP/Me/2000/98
Version 1.0
Page 2
Service Manual
Ergo R5000
Chapter 2.Troubleshooting Item
Condition
Probable Reasons
Solutions
1. Mouse can’t work
1. Cursor can’t work
1. Receiver or mouse failed
Change Receiver PCBA or mouse upper PCBA
2. Button can’t work
1.Press button no respond
1. Mouse PCBA
Change mouse down PCBA or SW1,2,3,4.
1. Battery no power or sensor failed
1. Change new battery or mouse sensor PCBA
3. Cursor can’t 1. Cursor can’t move smoothly move smoothly or can’t work
2. Receiver failed
2. Change receiver PCBA 4. Receiver can not charge
1.recharge battery has no power 1.Receiver failed
Version 1.0
Page 3
1.Change receiver PCBA
Service Manual
Ergo R5000
Chapter 3. Testing Procedures a. Testing flow chart START
F Check Receiver
Replace Receiver
T F
Replace battery
Check Mouse LED
or Mouse down PCBA
T F Check Mouse buttons
Replace Mouse down PCBA
T F
Replace battery or Mouse down PCBA
Check Cursor
T F Replace Receiver PCBA or Mouse upper PCBA
Check Connecting between PC with Mouse
T
Version 1.0
Page 4
Service Manual
Ergo R5000
Replace Receiver PCBA
F
Can not Recharge
T END
Version 1.0
Page 5
Service Manual
Ergo R5000
b.Check receiver. If cursor can not work or can not move smoothly ,please use another new good receiver with original mouse to check whether the cursor can function or not, if yes it means the former receiver is bad so please replace receiver PCBA. Receiver PCBA
Version 1.0
Page 6
Service Manual
Ergo R5000
c.Check Mouse LED If the mouse LED is off the mouse will not function, please replace new battery or mouse sensor PCBA. Mouse LED
Mouse sensor PCBA
Version 1.0
Page 7
Service Manual
Ergo R5000
d.Check mouse buttons If the mouse buttons do not function, please replace mouse SW1,SW2,SW3,SW4. Mouse SW1,2,3,4
Version 1.0
Page 8
Service Manual
Ergo R5000
e.Check cursor If cursor is unstable or does not move smoothly, please replace new battery. If still does not work after replacing new battery please replace mouse upper PCBA. Mouse upper PCBA
Version 1.0
Page 9
Service Manual
Ergo R5000
f.Check connecting between PC and mouse If mouse LED is on and depress channel connect button the mouse still can not function, please replace mouse upper PCBA or receiver PCBA. Mouse upper PCBA
Receiver PCBA
Version 1.0
Page 10
Service Manual
Ergo R5000
g.Can not recharge If recharge battery has no power after recharged,please replace receiver PCBA. Receiver PCBA
Version 1.0
Page 11
Service Manual
Ergo R5000
Chapter 4. Removal and Replacement Step
Description
Picture
1. Turn over mouse
To disassemble the mouse, you have to turn over mouse.
2. Loose screws
Using screwdriver to loose 2 screws after taking the battery cover apart.
Version 1.0
Page 12
Service Manual 3. Take apart PCBA
Ergo R5000
Take apart the upper cover and then loose screws as red arrows pointed to pick PCBA directly.
The PCBA is the most important part of mouse.
Upper PCBA
Version 1.0
Page 13
Service Manual
Ergo R5000
4. Loose screws to take the sensor PCBA
Sensor PCBA
Version 1.0
Page 14
Service Manual
Ergo R5000
Chapter 5. Part list Item
Parts number
Description
1
20000503000
Receiver PCBA
2
20000506000
Mouse upper PCBA
3
20000507000
Mouse down PCBA
4
20000657101
Mouse sensor PCBA
5
10900001200
Button for SW1,SW2,SW3,SW4
Chapter 6. Tools 1. Screwdriver cross
Version 1.0
Page 15
