Transcript
ICF-CD823 SERVICE MANUAL
US Model Canadian Model AEP Model Australian Model
Ver 1.1 2001. 04
Model Name Using Similar Mechanism
NEW
Optical Device Name
KSM-213CDM
Optical Pick-UP Name
KSS-213C
SPECIFICATIONS CD player section
General
System: Compact disc digital audio system Laser diode properties: Material: GaAlAs Wavelength: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) +1 Frequency response: 20-20,000 Hz –1.5 dB
Time display: North and South America and Australia: 12-hour system Other countries: 24-hour system Speaker: 77 mm (3 1⁄8 inches) dia., 4 Ω Output: i (headphones) jack (ø 3.5 mm stereo minijack) (except North American model) Power outputs: 1.2 W + 1.2 W (at 10% harmonic distortion) Power requirements: North and South American model: 120 V AC, 60 Hz Australian model: 240 V AC, 50 Hz Other models: 220-230 V AC, 50 Hz Dimensions: Approx. 250 × 153 × 207 mm (w/h/d) (Approx. 9 7⁄8 × 6 1⁄8 × 8 1⁄4 inches) incl. projecting parts and controls Mass: Approx. 1,700 g (3 lb. 12 oz.)
Wow and flutter: Below measurable limit
Radio section Frequency range: Band US, Canadian: FM 87.5-108 MHz AM 530-1,710 kHz AEP: FM 87.5-108 MHz AM 531-1,602 kHz 530-1,610 kHz Australian: FM 87.5-108 MHz AM 531-1,602 kHz
Channel step 0.1 MHz 10 kHz 0.05 MHz/0.1 MHz 9 kHz 10 kHz 0.05 MHz 9 kHz
Design and specifications are subject to change without notice.
FM/AM CD CLOCK RADIO 9-927-915-12
Sony Corporation
2001D1600-1 © 2001.4
Personal Audio Company Shinagawa Tec Service Manual Production Group
TABLE OF CONTENTS 1. GENERAL ········································································ 4 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5.
CABINET, LOWER ······················································ 5 MAIN BOARD ····························································· 6 PANEL (FRONT) SUB ASSY ······································ 6 OPTICAL PICK-UP BOLCK (KSM-213CDM) ·········· 7 TRANSFORMER BOARD ··········································· 7
3. TEST MODE ······························································· 8 4. ELECTRICAL ADJUSTMENTS ························ 10 5. DIAGRAMS 5-1. BLOCK DIAGRAM ··················································· 11 5-2. CIRCUIT BOARDS LOCATION ······························· 13 5-3. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) – ·········································· 14 5-4. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) – ·········································· 17 5-5. PRINTED WIRING BOARD – MAIN SECTION – ·················································· 20 5-6. PRINTED WIRING BOARD – PANEL SECTION – ················································· 23 5-7. IC PIN FUNCTION DESCRIPTION ························· 25 5-8. IC BLOCK DIAGRAMS ············································ 26
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
6. EXPLODED VIEWS 6-1. LOWER CABINET SECTION ··································· 29 6-2. UPPER CABINET SECTION ···································· 30 6-3. OPTICAL PICK-UP SECTION (KSM-213CDM) ························································· 31
0.15 µF
1.5 k Ω
AC voltmeter (0.75 V)
7. ELECTRICAL PARTS LIST ································· 32 Earth Ground Fig. A. Using an AC voltmeter to check AC leakage.
Note on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
—2—
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
LASER DIODE AND FOCUS SEARCH OPERATION CHECK 1. Open the CD lid. 2. Turn on S501 as following figure. 3. Confirm that the laser diode emission while observing the objecting lens. When there is no emission, Auto Power Control circuit or Optical Pick-up is broken. Objective lens moves up and down once for the focus search. Insert a precision screwdriver and push S501.
NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. • Code number of Chuck Plate Jig: X-4918-255-1
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the bottom exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
—3—
laser diode emission
SECTION 1 GENERAL This section is extracted from instruction manual.
Setting the Clock and Date 1 Set the alarm setting dial to ALARM MODE OFF. 2 Plug in the clock radio. The display will flash “AM 12:00” or “0:00”. 3 Press CLOCK for a few seconds. You will hear a beep and the year will start to flash in the display. 4 Press CLOCK + or – until the correct year appears in the display. 5 Press CLOCK once. 6 Repeat steps 4 and 5 to set the month, day, hour, and minute. After setting the minute, press CLOCK to start the counting of the seconds, and you will hear two short beeps. • To display the year and date, press SNOOZE/ DATE/SLEEP OFF once for the date, and within 2 seconds press it again for the year. The display shows the date or year for a few seconds and then changes back to the current time. • To set the current time rapidly, hold down CLOCK + or –. • The clock system varies depending on the model you own. 12-hour system: “AM 12:00” = midnight 24-hour system: “0:00” = midnight • In step 6, when you press CLOCK after the minute setting to activate the clock, the seconds start counting from zero. • When the alarm setting dial is set to ALARM TIME SET A or B, the clock cannot be set. To change the display to the daylight saving time (summer time) indication Press D.S.T./SUMMER T. “s” is displayed and the time indication changes to summer time. To deactivate the summer time function, press D.S.T./SUMMER T. again.
—4—
SECTION 2 DISASSEMBLY • The equipment can be removed using the following procedure. Set
Cabinet, lower
Main board
Panel (front) sub assy
Transformer board
Optical pick-up block (KSM-213CDM)
Note: Follow the disassembly procedure in the numerical order given.
2-1. CABINET, LOWER
1 Four screws (+BVTP 3 × 10)
2 Two screws (+P 3 × 14)
3 Three screws (+P 3 × 14)
5 Cabinet, lower
4 Connector
—5—
2-2. MAIN BOARD
1 Four screws (+P 3 × 6) 4 Panel (front) assy
0 Flat cable
9 Screw (+P 3 × 6)
8 Screw (+P 3 × 6)
qs Main board
2 Connector 5 Screw (+P 3 × 6)
3 Connector
6 Connector
7 Key (upper) board
qa Connector
2-3. PANEL (FRONT) SUB ASSY 5 Knob (alarm) (A)
6 Button (alarm) (A)
3 Three screws (+BTP 2.6 × 6) 2 Key (front) board
7 Panel (front) sub assy 4 Dial (alarm) assy
—6—
1 Four screws (+BTP 2.6 × 6)
2-4. OPTICAL PICK-UP BLOCK (KSM-213CDM)
1 Screw (+P 3 × 6) 2 Cover (unit)
4 Two screws (2.6 × 10)
3 Two screws (2.6 × 10)
5 Optical pick-up block (KSM-213 CDM)
2-5. TRANSFORMER BOARD
3 Two screws (+BTP 3 × 6)
1 Screw (+BTP 3 × 10)
2 Stopper, cord
4 Heat sink
5 Transformer board
power cord Power board
—7—
SECTION 3 TEST MODE 3-1 LCD Test Mode • The LCD test mode is initiated by turning off the main power once then back on or by resetting the machine while TP415 (LCD TEST, pin60 terminal) is connected to GND. (LCD segment) • The LCD test mode operations are listed in the following table. • When the machine enters the LCD test mode, all LCDs turn on. • Pressing any key turns off the corresponding segment of the LCD.
Correspondence between the keys and segments of LCD are as follows. KEY
SEGMENT
KEY
SEGMENT
1
1a, 1b, 1c, 1d, 1e, 1g
2
2a, 2b, 2c, 2d, 2e, 2f, 2g,
OFF
A CD
3
3a, 3b, 3c, 3d, 3e, 3f, 3g,
CD
CD H
4
4a, 4b, 4c, 4d, 4e, 4f, 4g,
RADIO
RADIO
5
5a, 5b, 5c, 5d, 5e, 5f, 5g, WAKE UP TRACK
TRACK
BAND SNOOZE D.S.T CLOCK + CLOCK
FM, MW, LW SLEEP
CLOCK
CD PLAY MODE
AM, PM,
REP, 1, ALL, SHUFFLE, CD
s 6a, 6b, 6c, 6d, 6e, 6f, 6g,
TUEN +
B RADIO
:, .
TUEN –
B BUZZER
• Pressing the [ALARM TIME CHECK] button at end of the LCD test mode shows the version number of the software on the LCD. • The alarm-dial position detection can be checked and displayed if the alarm-dial is operated while the version number is being displayed on LCD. • State of the [ALARM-B: RADIO/BUZZER] slide switch position can be detected and displayed on the alarm picture.
3-2 CD Test Mode 3-2-1 CD TEST-1 (AUTO) • The CD TEST-1 (AUTO) mode is initiated by turning off the main power once then back on or by resetting the machine while TP414 (CD TEST, pin-59 terminal) is connected to GND. • When the machine enters CD TEST-1 (AUTO) mode, it repeats the focus search until the focus becomes OK. • After the focus becomes OK and the focus is automatically adjusted, rough servo is locked in and the adjustment value is displayed. CD SRUFFLE
F-E BALANCE ADJUSTMENT
TRACKING GAIN ADJUSTMENT
AM
TRACK FOCUS BIAS ADJUSTMENT
• The sled can be moved to the innermost track by pressing the minus (-) button. The sled can be moved to the outermost track by pressing the plus (+) button. • When the BAND button is pressed, the machine enters the CLVA (servo ON) and the mute is turned OFF if data is read successfully. When the following button is pressed, the corresponding operations are performed. a) 1 Setting the 1 track jump b) 2 Setting the 10 track jump c) 3 Setting the 100 track jump Afterwards the desired track jump can be set by pressing the plus (+) or minus (-) button. d) 4 TRACKING GAIN-UP e) BAND’s rough servo • P5 Restarts CD TEST-1 (AUTO) mode from the focus automatic adjustment • When the CD button is pressed then, the track jumps to the second session and the machine exits the CD TEST-1 (AUTO) mode. • When the OFF button is pressed, the CD playback is stopped. If the CD button is pressed again, the machine repeats operations from the focus search. 3-2-2 CD TEST-2 (MANUAL) • The CD TEST-2 (MANUAL) mode is initiated by turning off the main power once then back on or by resetting the machine while TP413 (A MUT, pin-58 terminal) is connected to GND. • When the machine enters CD TEST-2 (MANUAL) mode, it repeats the focus search until the focus becomes OK. • After the focus becomes OK, the machine enters the rough servo. • The sled can be moved to the innermost track by pressing the minus (-) button. The sled can be moved to the outermost track by pressing the plus (+) button. • When the BAND button is pressed, the machine enters the CLVA (servo ON) and the mute is turned OFF if data is read successfully. When the BAND button is pressed again, the machine enters the rough servo. • When the CD button is pressed then, the track jumps to the second session and the machine exits the CD TEST-2 (MANUAL) mode. • When the OFF button is pressed, the CD playback is stopped. If the CD button is pressed again, the machine repeats operations from the focus search.
—8—
CD TEST-1
FOCUS OK
N
Y Auto adjustment
Rough servo
+button
CD button Y
OFF button
BAND button
Y
Y
Y
TEST MODE END The second music played back.
Sled maement
Servo ON
CD STOP
CD button
+button
BAND button
OFF button
Y
Y
N
Y
CD button
Y
jump has been set? Y
1 Y
Execntes the setting of jump.
2
3
Y
4 Y
Y
Sets the respective setup valnes.
N
Y
Rough servo
+button Y
Sled maement
+button Y
BAND button
CD button
OFF button
Y
Y
Y
TEST MODE END The second music played back.
Servo ON
BAND button Y
CD STOP
OFF button
CD button
CD button
Y
Y
Y
—9—
Y
TRACKING GAIN UP
CD TEST-2
FOCUS OK
5
SECTION 4 ELECTRICAL ADJUSTMENTS PRECAUTION • Adjustment should be performed in the order given.
TUNER SECTION
FM VCO Adjustment Procedure: FM RF signal generator
0 dB=1 µV
[FM] Setting: Function switch : RADIO BAND switch : FM
0.01 µF Carrier frequency: 98 MHz Modulation: no modulation Output level: 0.1 V (100 dB)
FM RF signal generator
FM lead wire antenna terminal
1. Connect the frequency counter to 4 and 7 pins of IC1 as shown the figure right. 2. Tune the set to 98 MHz. 3. Adjust RV1 for 76 kHz Hz reading on frequency counter.
0.01 µF 75 kHz frequency deviation by 1 kHz signal. Output level: as low as possible FM lead wire antenna terminal
Specification Value:
[AM] Setting: Function switch : RADIO BAND switch : AM signal AM RF signal generator
Frequency counter 75,500 – 76,500 Hz
Put the lead-wire antenna close to the set.
Connection:
30% amplitude modulation by 400 Hz signal. Output level: as low as possible
frequency counter
33 k Ω
MAIN Board
+ –
level meter
IC1 Pin 7 IC1 Pin 4
32 Ω + –
set
Adjustment Location:
J301 (phones)
[MAIN BOARD] (Component Side) • Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors.
CT1 FM Traking Adjustment
RV1 FM VCO Adjustment
FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter L2
L2 FM Frequency Coverage Adjustment
87.5 MHz
FM TRACKING ADJUSTMENT
L1 FM Tracking Adjustment
Adjust for a maximum reading on level meter L1
87.5 MHz
CT1
108.0 MHz
T1 AM IF Adjustment L4 AM Frequency Coverage Adjustment
AM IF ADJUSTMENT Adjust for a maximum reading on level meter T1
450 kHz
CT2 AM Traking Adjustment
AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter L4
530 kHz
L3 AM Traking Adjustment
AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter L3
600 kHz
CT2
1,400 kHz
— 10 —
ICF-CD823
SECTION 5 DIAGRAM 5-1. BLOCK DIAGRAM
Note on Printed Wiring Board: • X : parts extracted from the component side. • b : Pattern from the side which enables seeing.
AEP, Australian model
FM/AM FRONT- END IC1
MAIN BOARD
HEADPHONE BOARD RV301 VOLUME L OUT 6
ANT1
11
(FM ANTENNA)
B.P.F
18 FM RF IN
3
CF3 10.7MHz
MIX OUT 16
21 REG L1 FM RF
12 MUTE CONT Q302
CF2 450kHz
CT1
L2 FM OSC
SP101
SP201
MUTE CONT Q351,352
SYSTEM CONTROL IC401 15 BAND
MUTE Q354
R
BUZZER 53 POWER ON 64 LCD401
D4
VCO 27 LIQUID CRYSTAL DISPLAY PANEL
RV1
US, Canadian model
FM VCO
L4 AM OSC AM FREQUENCY COVERAGE
24 AM OSC
TU +B
+B SW Q5
SEG0 11 SEG15 26
+5V 60 RADIO ON
PLL IC51 12 FM IN
P1 8
11 AM IN 61 R DATA
DATA 5 L.P.F Q51,52
15 PD
PLL +B
CLK 4
62 R CLK
LAT 3
63 R LAT
X OUT
X IN
1
2
KS0
35
KS2
37
S701-713 FUNCTION KEY
KRO0 38
KEY(FRONT) BOARD
X51 75kHz
KR0
41
KR3
44
S715-718 FUNCTION KEY
KR04 64
OPTICAL PICK-UP BLOCK (KSS-213C)
DIGITAL SERVO DIGITAL SIGNAL PROC. D/A CONV. IC551
RF AMP IC501 51 VC
VC +5V
RFO 33
35 RF
38 PD1
B
39 PD2
A OUT2 76
E
42 E
F
41 F Q501 LD DRIVE
LD
36 LD
GND
PD
DATA 22
12 DATO
CLK 20
14 CLKO
XLT 21
13 XLTO
FOK 27
18 FOK
COUT 24
11 CIN
SENS1 25
10 SEIN
F+
26 F+
F-
27 F-
T+ TRACKING COIL
17 T+
DATA 7
77 C DATA
CLK 9
75 C CLOCK
XLAT 8
76 C LATCH
SQCK 4
56 C SQCK
SCOR 57
49 C SCOR
SQSO 5
54 C SQSO
SENS 6
52 C SENS
SMUTE 62
55 C MUTE
MOTOR/COIL DRIVE IC591 6 FEO
(F IN) 24
7 FEM
T IN 19
13 TAO
5.6 Vp-p
MOTOR (6P) board KEY (UPPER) board
RESET IC402
HEADPHONE board
BACK LIGHT board
PLL +B
D910
CD +B X501 16.9344MHz
SL IN 3
REG Q301
TRANSFORMER BOARD
CD ON 59 +5V
2 SL+
59 ns 2.0 V/DIV, 40 ns/DIV
AC IN 51
18 T-
MOTOR(6P) BOARD
3 IC551 ua (XTA0)
D903
XTAO 72
M571 SLED MOTOR
RESET 67
XTAI 71 T-
0.9 – 1.3 Vp-p 0.2 V/DIV, 500 ns/DIV
5-2. CIRCUIT BOARD LOCATION
BUZZER
D901,902 25
F IN
(PLAY MODE)
D402-404
XRST 23 VR
2 IC501 ed (RF0)
BACK LIGHT BOARD
SENS2 26
37 PD
3.4 Vp-p
KRO1 32 KR03 34
L OUT2 74
C D
FOCUS COIL
RADIO
A OUT1 65
31 ms 1.0 V/DIV, 20 ms/DIV
S719,721-723 DIAL (ALARM)
S720 ALARM B
L OUT1 67
RFI 32
A
Note: Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
no mark : FM ( ) : AM < > : CD • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Signal path. F : FM f : AM J : CD • Abbreviation CND : Canadian model AUS : Australian model
KEY(UPPER) BOARD
COM0 7 COM3 10
1 IC401 ud (XT1)
Note on Schematic Diagrams: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. ¢ : internal component. • • 2 : nonflammable resistor. • C : panel designation. • H : adjustment for repair. • U : B+ Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
A MUTE 58
AM RF
19
L SPEAKER
BUFFER Q203
CF1
AM TRACKING
MUTE Q201
MUTE Q353
DISCRI 26 L3 MW ANT
3
BUFFER Q103
14 AM IF
AM IF
22 FM OSC
FM FREQUENCY COVERAGE
BUFFER Q202
T1 AM IFT
20 FM RF OUT FM TRACKING
R OUT 5
13 FM IF
5
POWOR AMP IC351
MUTE Q101
BPF1 1
J301
BUFFER Q102
• Waveforms
16 SLO
REG Q901 D904-907
M +5V
1 SL-
M
T901 POWER TRANSFOMER
MAIN board
REG Q902
AC IN
XRST 79
12 SP+
SP IN 15
21 MDP
11 SP-
MUTE 7
15 SPOA(LIMIT)
XLDON MUTE 17 M572 SPINDLE M MOTOR
S570 LIMIT SW
TRANSFORMER board
50 C SENS2 57 C RST
• Signal Path : FM
47 DOOR IN
S501 DOOR SW
: CD
KEY (FRONT) board
16
— 11 —
— 12 —
— 13 —
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
— 15 —
○
• Refer to page 26 for IC Block Diagrams.
○
○
• Refer to page 25 for IC Pin Function Description.
○
— 14 — ○
• Refer to page 13 for Waveforms.
○
5-3. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) –
○
○
○
○
○
○
○
ICF-CD823
— 16 —
○
○
○
○
ICF-CD823 5-4. SCHEMATIC DIAGRAM – MIAN SECTION (2/2) –
• Refer to page 13 for Waveforms.
• Refer to page 26 for IC Block Diagrams.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
— 17 —
— 18 —
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
— 19 —
○
○
○
○
○
○
○
○
ICF-CD823
6
7
8
9
○
5
○
4
○
3
10
11
12
13
○
○
○
○
2
○
1
5-5. PRINTED WIRING BOARD – MAIN SECTION –
MAIN BOARD (SIDE B)
○
○
A
CN401
○
○
A
○
○
TO KEY (UPPER) BOARD
○ ○
C11
C51
○
ANT1 (FM ANTENNA)
L3
○ ○
○ ○
○
C65
RV1
○
L1
○
C
CT2
BPF1
○
C18
L2
○
○
○
○
○
○
CN403
C15
C17
○
○
○
TO BACK LIGHT BOARD
○
○
○
○
B
○
○
S501 (DOOR SW)
16 CF3
○
○
○
○
○
30
○
○
CF1 C20
1
15
○
○
○
○
○
AEP,AUS MODEL
C23
○
○
C
○
○
C584 T1
○
○
20
○
○ ○ ○ ○ ○ ○ ○ ○
X501 AEP,AUS
MODEL
○
C914 Q901
C580
R904
X401
CN502
C436
C515
C915
○
○
C402
○
80
C559
○
1
61
○
○
21
F TO MOTOR (6P) BOARD
○
○
○
1
○
○ ○ ○
60 80
C25
○
US,CND,AUS MODEL
○
61
LCD401 (LIQUID CRYSTAL DISPLAY)
40
D
CF2
○
US,CND MODEL
○
41
21 20
C566
○
○
41
60
1
○
○ ○
○
40
AEP MODEL
14
C599
C511
C912 ○
C918 ○
○
13
○
○
C446
C447
R907
○
○
20
Q902
C521
1 28
○
IC402
C919
○
○
○
15
○
52
○
40
○
39
○
○
E
○
X402
○
1
○
14
○
26 27
C524
○
C353 C152
C252
○
○
○
○
C355
○
○
C909
CN501
○
○
○
C910
○
1
16
C595
15
1
○
○
○
○
○
○
○
○
IC351
RV301 VOLUME
○
○
○
F
○
○
○
○
○
○
Q501
○
C154
C526
C254
D904
C255
C155
C103
1-678-388-
○
○
○
○
D907
AEP,AUS MODEL
C256 C156
○
D906
○
○
○
○
○
C908 D905
C203 ○
○
(11)
○
(11)
○
1-678-388-
○ ○ ○ ○
D
SP101 (L ch) SP201 (R ch)
US,CND MODEL
TO OPTICAL PICK-UP BLOCK (KSS-213C)
— 21 —
○ ○
— 20 —
○
○
○
○
○
○
○
○
○
○
TO TRANSFORMER BOARD
C105
11
CN351
○
KH901
○
○
16
○
G
E
C106
○
○
11
○
○ ○
○
TO HEADPHONE BOARD
○
C-4 A-10 A-10 G-11 F-11 F-12 F-11 G-11 G-12 D-3 G-11 F-9 F-9 G-9 G-9 F-12 D-10 E-10
CN402
○
Q5 Q51 Q52 Q101 Q102 Q103 Q201 Q202 Q203 Q301 Q302 Q351 Q352 Q353 Q354 Q501 Q901 Q902
B
○
○
16
○
C-10 A-4 F-10 D-5 E-8 E-2 D-2 E-3
9
○
IC1 IC51 IC351 IC401 IC402 IC501 IC551 IC591
B-10 B-10 B-11 G-11 F-12 F-11 D-3 D-4 D-2 D-3 D-13 F-8 F-8 F-8 G-8 F-8 F-8 G-8 D-10 E-10 F-8
○
D2 D3 D4 D101 D102 D201 D301 D401 D501 D551 D552 D901 D902 D903 D904 D905 D906 D907 D908 D909 D910
X51
○
TO KEY (FRONT) BOARD
○
1
○
8
Location
○
Ref. No.
○
Location
○
○
○
○
○
• Semiconductor
L4
C62
○
• Refer to page 13 for Circuit Board Location.
○
○
○
○
○
○
MAIN BOARD (SIDE A)
— 22 —
ICF-CD823 5-6. PRINTED WIRING BOARD – PANEL SECTION –
1
• Refer to page 13 for Circuit Board Location.
2
3
4
5
6
7
8
9
10
AEP,AUS MODEL
KEY (UPPER) BOARD
A
J301
S713 WAKE UP TRACK SPEAKER
TUNING
L251
A
S702
B
S709 5
SP201 (R ch)
L151 1
S704 4 S712 3
S710 RADIO S708 2 S703 1
BH351
S706 BAND
SP101 (L ch)
CNP352
TO MAIN BOARD
L351
S701
S711 CD PLAY MODE
9 BH701
1-678-393-
S705 CD
TO MAIN BOARD
11 (11)
HEADPHONE BOARD
S707 OFF
11 1-678-390-
(11)
MOTOR (6P) BOARD
SNOOZE/DATA SLEEP OFF S714
C
TO MAIN BOARD
BACK LIGHT BOARD KEY (FRONT) BOARD
E
TO DIAL (ALARM)
M572 SPINDLE MOTOR
F
BACK LIGHT D404
D403
D402
S570 (LIMIT) 1
D
BH704
11 BH702
11
CN701
TO MAIN BOARD
1-678-391-
B
C
S716 CLOCK
R702
M571 SLED MOTOR
(11)
TO MAIN BOARD
TRANSFORMER BOARD
E BUZZER
S720 ALARM B
RADIO
AC IN
LF901
S715
F
CLOCK S717 S718 D.S.T
11 1-678-389-
CN901
T901 POWER TRANSFORMER
11
(11)
1-678-392-
16
G
D
— 23 —
TO MAIN BOARD
— 24 —
(11)
5-8. IC BLOCK DIAGRAMS
30
29
28 27
VSS1
−
Ground
7–10
COM0–3
O
LCD drive common signal
11–26
COM3–15
O
LCD drive segment signal
FM/AM FE OUT
LCD drive power supply
6
FM GND
LCD bias output
−
FM RF IN
O
AM RF IN
BIAS VLC0–2
VCO
2 3–5
FM RF
26 25 24 23 22 21
20
19
18
17
16
FM FRONT-END AM FRONT-END
27
NC
−
Not used
28–30
VERSION0–2
Ι
Initialization input
31
NC
−
Not used
32–34
KR01–3
Ι
Key return signal
35–38
KS0–3
Ο
Key strobe signal
39
AVDD
−
Analog power supply
40
AVREF
−
A/D converter reference voltage
41–45
KR0–4
I
Key return signal
46
KR00
I
Key return signal
47
DOOR IN
−
CD lid open/close detection
48
AVSS
I
Analog ground
49
C SCOR
I
Sub code sync input
50
C SENS2
I
CD SENS2 input
51
AC IN
I
Power failure detection
52
C SENS1
O
CD SENS1 input
53
BUZZER
O
Buzzer input
54
C SQSO
O
Sub code Q 80-bit serial output
55
C MUT
O
CD mute
56
C SQCK
O
CK for reading sub code Q 80-bit
57
C RST
O
CD reset output
58
AMUT
O
Audio muting output
59
DC ON
O
CD ON output
VSS
PDI
VDD1
VDD2
FM IN
AM IN
P2
IF-IN
REG
60
RADIO ON
O
Radio ON output
16
15
14
13
12
11
10
9
61
R DATA
O
Radio data output
62
R CLK
O
Radio CLK output
63
R LAT
O
Radio LAT output
64
POWER ON
O
Power ON output
65
SHIFT0
O
Serial clock output 0
66
SHIFT1
I
Serial clock output 1
67
RESET
O
Serial reset input
68
X2
I
Main system clock output
69
X1
−
Main system clock input (4.19 MHz)
70
VSS0
−
Ground
71
VDD0
Ο
System power supply
72
XT2
Ι
Sub system clock output
73
XT1
−
Sub system clock input (32 kHz)
74
IC
Ο
Normally, not used. (Used for writing)
75
C CLK
Ο
CD CLK output
76
C LAT
Ο
CD LAT output
77
C DATA
−
CD data output
78–80
NC
−
Not used.
FM IF/ DISCRI
MPX REG. 1/2 COUNTER 1/2 COUNTER
MONO/ST SELECT
AM IF/DET
PD1 PD2
MUTING
IC51
12
13 14 15
COUNT IF
MAIN CTL PRESCALER
OUT PUT CTL
6
7
8
P1
CE
5
P0
X IN
4
CD
3
DA
2
CK
1
X OUT
I/O CTL REDISTER
— 26 —
BAND SELECT
11
BU2614FS-E2
PHASE DET
— 25 —
10
AM IF IN
9
TUNE IND
8
GND
7
AGC AFC2
6
AGC AFC1
PILOT DET LPF2 ST IND/ VCO CHECK
5
RIPPLE FILTER
PLL LPF1
PILOT DET LPF2
4
L CH OUT
3
R CH OUT
2
BAND PASS MUTE
RIPPLE FILTER
DECODER AMP 1
TUNING INDICATOR
AUTOBLEND
VCC
VCO
FM IF IN
System power supply
REG
−
FM OSC
VDD1
CXA1238M-T6
AFC
1
IC1
Description
MPX REG
I/O
PLL LPF2
Pin Name
GND
Pin No.
AM OSC
• MAIN BOARD IC401 µPD789407AGK (SYSTEM CONTROL/LCD DRIVER)
FM DISCRI MUTE
5-7. IC PIN FUNCTION DESCRIPTION
33
CC2 FOK
34
CC1
35
CP
RF I
36
CB
RF O
37
RF M
38
RFTC
PD0
39
LD
PD1
CXA1992BR PD2
IC501
32 31
30
29
28 27
VEE
PD2 IV AMP
RF SUMMING AMP
PD1 IV AMP
26 SENS2 IIL
FE BIAS 40
25 SENS1 VCC APC TTL
F 41 VEE LASER POWER CONTROL
F IV AMP
FE AMP
VCC
E 42
24 C OUT
VCC
E IV AMP
VCC 23 XRST
VEE
BAL1 BAL2 BAL3
IFB1 IFB2 IFB3 IFB4 IFB5 IFB6
BAL4
EI 43
22 DATA
TGFL VEE
VEE VEE 44
VEE
TTL
DFCT TOG1 TOG2 TOG3 TOG4
VEE
LEVEL 9
TRK GAIN WINDOW COMP
TEO 45
IIL IIL
FO BIAS WINDOW COMP
E-F BALANCE WINDOW COMP
LPF1 46
21 XLT
MIRR
20 CLK
TTL 19 LOCK VCC FOK
FOH FOL TGH TGL BALH BALL ATSC TZC FZC
TZC 49 TZC COMP VCC TDFCT 50
DFCTO TM1
IFB1–6 BAL1–4 TOG1–4
18 VCC
ISET
17 ISET
CC1
DFCT1
MIRR FS1–4
TG1–2
TM1–7
PS1–4 VCC
TRACKING PHASE COMPENSATION
VCC
VCC
IIL DATA REGISTER INPUT SHIFT REGISTER SENS SELECTOR OUTPUT DECODER
DFCT VC 51
TGFL
LPC
ATSC WINDOW COMP
LPCL
ATSC 48
LDON
TEI 47
VCC TM6
TM4
TG1
16 SL O
VEE FZC 52
15 SL M VCC
TM7 TM3
FS1
TM5
FOCUS PHASE COMPENSATION DFCT FZC COMP
FS2
VEE
CHARGE UP
FS4
VEE
TG2 FSET 14 SL P
VEE 4
5
6
7
8
9
10 11 12
13
FDFCT
FGD
FLB
FE O
FE M
SRCH
TGU
FSET
TA O
— 27 —
TA M
3
TG2
1 2 FEO FEI
TM2
EXCK SBSO SCOR
WFCK
ENPHI
EMPH
DOUT C4M XTSL C2PO
GFS
XPCK
XUGF
VDD
VSS
BCKI
BCK
PCMDI
PCMD
CXD2589Q VSS
IC551
60
59 58 57
56
55
54 53 52 51 50
49
48
47
46
45
44
43
42
41
VDD 61 SYSM 62 SERIAL-IN INTERFACE
PWM
40 LRCKI 39 LRCK
AVSS 63
38 ASYO
OVER SAMPLING DIGITAL FILTER
37 ASYI EFM DEMODULATOR
AVDD 64
ASYMMETRY CORRECTOR
36 BIAS 35 RF
AOUT1 AIN1 LOUT1 AVSS XVDD XTAI
65 66 67 68 69 70
3rd-ORDER NOISE SHAPER
34 AVDD
33 CLTV TIMING LOGIC
ERROR CORRECTOR
16K RAM
32 AVSS
SUB CODE PROCESSOR
DIGITAL PLL
PWM XTAO 71
31 FILI 30 FILO 29 PCO
XVSS 72 DIGITAL OUT
D/A INTERFACE
AVSS 73 OSC
LOUT2 74 AIN2 75 AOUT2 76
28 V16M 27 VCTL
26 VCKI 25 VPCO1
CLOCK GENERATOR
24 TES1 AVDD 77 23 TES0 AVSS 78
CPU INTERLACE
22 PWMI DIGITAL CLV
SERVO AUTO SEQUENCER
XRST 79
21 MDP
18
19
20
VSS
17
VDD
16
FOK
15
XLON
14
SPOB
13
SPOA
12
CLKO
11
XLTO
10
DATO
9
CNIN
8
SEIN
SQCK
SQSO
7
XLAT
VSS
6
CLOK
5
DATA
4
SENS
2 3
VCC
22
21
20
19
18
17
NC OPIN-B
VCC
23
OUT3-B
VREF IN
24
OUT3-A
IN4
25
IN3
IN4
26
,
OUT4-A
27
IN3
OUT4-B
28
,
GND
BA6898FP-E2
16 15 NC
VCC
VCC
LEVEL SHIFT
+ –
LEVEL SHIFT – +
+ – REGULATOR BIAS, T. S. D MONITOR
DRIVER MUTE
+ –
+ –
+ –
LEVEL SHIFT
LEVEL SHIFT
— 28 —
11
12 13
14
OPOUT
IN1 RESET REG-B REGOUT
9 10
OUT2-B GND
OUT1-B
7 8
OUT2-A
3 4 5 6
, IN2 IN2
2
MUTE GND
1
OUT1-A
+ –
IC591
1
LMUTE RMUTE
VDD 80
SECTION 6 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
•
The mechanical parts with no reference number in the exploded views are not supplied. Accessories and packing materials are given in the last of this parts list. Abbreviation CND : Canadian model. AUS : Australian model.
• •
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
6-1. LOWER CABINET SECTION
1 2
4
S501
3 12 11
#3 #2 not supplied
8
#3 not supplied
#2
7
5
6
#4 #4
Ref. No.
6
Remarks
#2
Part No.
Description
Ref. No.
Part No.
Description
1 2 3 4 5
3-045-074-01 3-045-079-01 3-045-066-01 3-045-069-01 3-045-064-01
WINDOW (CD) SPRING (CD) LID,CD BUTTON (SNOOZE) CABINET, LOWER (US,CND)
08 08 11 12 S501
1-790-431-11 1-790-757-11 3-029-900-11 1-452-732-11 1-692-960-11
CORD, POWER (AUS) CORD, POWER (US,CND) PLATE (KSM-213CDM), CHUCKING MAGNET SWITCH, PUSH (1 KEY) (DOOR SW)
5 6 * 7 08
3-045-064-11 3-368-852-01 1-678-392-11 1-555-795-00
CABINET, LOWER (AEP,AUS) FOOT TRANSFORMER BOARD CORD, POWER (AEP)
#2 #3 #4
— 29 —
7-685-547-19 SCREW +BTP3X10 TYPE2 N-S 7-685-645-79 SCREW +P3X6 TYPE2 NON-SLIT 7-685-649-79 SCREW +P3X14 TYPE2 NON-SLIT
Remarks
Ver 1.1 2001. 04
6-2. UPPER CABINET SECTION 55
73
#1
62
70
#1
SP101
64 63
69 #3
58
56 #1
65 54 67
57 not supplied
66
#3
66
67 68
SP201
61
72
52 51
74
59
53
71 LCD401
#3
60
Ref. No.
Part No.
Description
Remarks
51 52 53 54 55
3-045-076-01 3-045-077-01 X-3378-844-1 3-713-786-51 X-3378-843-1
KNOB(ALARM) (A) BUTTON (ALARM) (A) PANEL (FRONT) SUB ASSY SCREW +P 2X3 CABINET (UPPER) SUB ASSY (US,CND)
55 56 57 58 * 59
X-3379-079-1 3-045-071-01 A-3638-886-A 7-671-155-01 A-3683-167-A
CABINET (UPPER) SUB ASSY (AEP,AUS) KNOB(ALARM) (B) DIAL(ALARM) ASSY STEEL BALL 3.0 MAIN BOARD,COMPLETE (US,CND)
* 59 * 59 60 * 61 * 62
A-3683-211-A A-3683-213-A 3-382-175-31 1-678-391-11 1-678-389-11
MAIN BOARD,COMPLETE (AEP) MAIN BOARD,COMPLETE (AUS) KNOB(V) BACK LIGHT BOARD KEY(FRONT) BOARD
* 63
1-678-390-11 KEY(UPPER) BOARD
Ref. No.
Part No.
Description
64 65 66 67 68
3-910-116-01 3-910-095-31 3-921-725-01 3-931-379-01 1-777-955-11
COVER, CD RUBBER, VIBRATION PROOF SCREW (2.6X10), +PWH RUBBER, VIBRATION PROOF WIRE(FLAT TYPE) (16 CORE)
69 70 71 * 72 * 73
3-048-293-01 3-351-377-11 3-045-072-01 1-639-678-12 1-678-393-11
COVER (UNIT) DAMPER HOLDER (LCD) MOTOR (6P) BOARD HEADPHONE BOARD (AEP,AUS)
74 SP101 SP201 LCD401 #1
X-3378-845-1 1-504-460-11 1-504-460-11 1-804-008-11 7-685-133-19
NET ASSY SPEAKER (7.7cm) (L-CH) SPEAKER (7.7cm) (R-CH) DISPLAY PANEL LIQUID CRYSTAL SCREW +BTP2.6X6 TYPE2 N-S
#3
7-685-645-79 SCREW +P3X6 TYPE2 NON-SLIT
— 30 —
Remarks
Ver 1.1 2001. 04
6-3. OPTICAL PICK-UP SECTION (KSM-213CDM)
102
not supplied
101 103
#4
104
M572
M571
Ref. No.
Part No.
Description
! 101 102 103 104
8-848-483-05 2-626-907-01 2-627-003-02 2-626-908-01
OPTICAL PICK-UP KSS-213CDM GEAR (A) GEAR (B) (RP) SHAFT, SLED
Remark
Ref. No. M571 M572 #4
Part No.
Description
X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED) X-2626-202-1 CHASSIS ASSY (MB), (RP) (SPINDLE) 7-685-649-79 SCREW +P3X14 TYPE2 NON-SLIT
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
— 31 —
Remark
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
BACK LIGHT KEY (FRONT)
HEADPHONE
SECTION 7 KEY (UPPER) ELECTRICAL PARTS LIST
NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
•
CAPACITORS: uF: µF RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable COILS uH: µH
•
•
When indicating parts by reference number, please include the board name.
Ref. No.
Part No.
Description
Remarks
*
1-678-391-11 BACK LIGHT BOARD ****************
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Description
Remarks
S715 1-692-014-11 SWITCH, KEY BOARD (CLOCK +) S716 1-692-014-11 SWITCH, KEY BOARD (CLOCK) S717 1-692-014-11 SWITCH, KEY BOARD (CLOCK -) S718 1-692-014-11 SWITCH, KEY BOARD (D.S.T) S720 1-692-181-21 SWITCH, SLIDE (ALARM) ************************************************************
8-719-056-07 LED SLR-342MC3F (BACK LIGHT) 8-719-056-07 LED SLR-342MC3F (BACK LIGHT) 8-719-056-07 LED SLR-342MC3F (BACK LIGHT) < RESISTOR >
1-678-390-11 KEY (UPPER) BOARD *****************
*
R497 1-216-033-00 METAL CHIP 220 5% 1/10W R498 1-216-033-00 METAL CHIP 220 5% 1/10W R499 1-216-033-00 METAL CHIP 220 5% 1/10W ************************************************************ 1-678-393-11 HEADPHONE BOARD (AEP,AUS) *************************
*
Part No.
SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...
< SWITCH >
< DIODE > D402 D403 D404
Ref. No.
•
< CAPACITOR > C701 C702 C703 C704 C705
1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0047uF 0.0047uF 0.0047uF 0.0047uF 0.0047uF
5% 5% 5% 5% 5%
50V 50V 50V 50V 50V
C706 C707 C708 C709 C710
1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0047uF 0.0047uF 0.0047uF 0.0047uF 0.0047uF
5% 5% 5% 5% 5%
50V 50V 50V 50V 50V
C711 C712 C713 C714 C720
1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00 1-163-251-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0047uF 0.0047uF 0.0047uF 0.0047uF 100PF
5% 5% 5% 5% 5.00%
50V 50V 50V 50V 50V
C721 C722 C723 C724 C725
1-163-251-11 1-163-251-11 1-163-251-11 1-163-251-11 1-163-251-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 100PF 100PF 100PF
5.00% 5.00% 5.00% 5.00% 5.00%
50V 50V 50V 50V 50V
C726 C727
1-163-251-11 CERAMIC CHIP 1-163-251-11 CERAMIC CHIP
100PF 100PF
5.00% 50V 5.00% 50V
< JACK > J301
1-566-891-11 JACK (HEADPHONES) < COIL >
L151 L251 L351
1-412-496-11 INDUCTOR 1-412-496-11 INDUCTOR 1-412-496-11 INDUCTOR
4.7uH 4.7uH 4.7uH
< RESISTOR > R157 1-216-033-00 METAL CHIP 220 5% 1/10W R257 1-216-033-00 METAL CHIP 220 5% 1/10W ************************************************************ 1-678-389-11 KEY (FRONT) BOARD *****************
*
< CAPACITOR > C715 C716 C717 C718
1-163-017-00 1-163-017-00 1-163-017-00 1-163-017-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0047uF 0.0047uF 0.0047uF 0.0047uF
< CONNECTOR > * CN701
50V 50V 50V 50V
< JUMPER > JC701 JC702 JC703
1-216-296-91 SHORT 1-216-296-91 SHORT 1-216-296-91 SHORT
1-568-271-11 SOCKET, CONNECTOR 5P < JUMPER >
JC702
5% 5% 5% 5%
1-216-295-91 SHORT
0
0 0 0
< SWITCH > S701 S702 S703 S704 S705
— 32 —
1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11
SWITCH, KEY BOARD (TUNING +) SWITCH, KEY BOARD (TUNING -) SWITCH, KEY BOARD (1) SWITCH, KEY BOARD (4) SWITCH, KEY BOARD (CD)
KEY (UPPER) Ref. No. S706 S707 S708 S709 S710
Part No.
Description
1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11
SWITCH, KEY BOARD (BAND) SWITCH, KEY BOARD (OFF) SWITCH, KEY BOARD (2) SWITCH, KEY BOARD (5) SWITCH, KEY BOARD (RADIO)
Remarks
S711 1-692-014-11 SWITCH, KEY BOARD (CD PLAY MODE) S712 1-692-014-11 SWITCH, KEY BOARD (3) S713 1-692-014-11 SWITCH, KEY BOARD (WAKE UP TRACK) S714 1-692-014-11 SWITCH, KEY BOARD (SNOOZE UP TRACK) ************************************************************ A-3683-167-A MAIN BOARD, COMPLETE (US,CND) ***************************** A-3683-211-A MAIN BOARD, COMPLETE (AEP) ************************** A-3683-213-A MAIN BOARD, COMPLETE (AUS) **************************
* * *
3-045-072-01 HOLDER (LCD) 3-382-175-31 KNOB (V) 7-685-645-79 SCREW +P 3X6 TYPE2 NON-SLIT
Ref. No.
MAIN
Part No.
Description
C54 C55 C56 C57 C58
1-162-964-11 1-163-239-11 1-163-233-11 1-162-927-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 33PF 18PF 100PF 100PF
10% 5.00% 5.00% 5% 5%
50V 50V 50V 50V 50V
Remarks
C59 C61 C62 C63 C64
1-162-927-11 1-163-133-00 1-136-171-00 1-163-021-91 1-163-021-91
CERAMIC CHIP CERAMIC CHIP MYLAR CERAMIC CHIP CERAMIC CHIP
100PF 470PF 0.33uF 0.01uF 0.01uF
5% 5% 5.00% 10.00% 10.00%
50V 50V 50V 50V 50V
C65 C66 C67 C103 C105
1-126-947-11 1-163-021-91 1-162-970-11 1-126-957-11 1-104-664-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT
47uF 0.01uF 0.01uF 0.22uF 47uF
20.00% 10.00% 10% 20.00% 20.00%
35V 50V 25V 50V 10V
C106 C151 C152 C153 C154
1-104-665-11 1-162-964-11 1-126-963-11 1-163-009-11 1-104-664-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
100uF 0.001uF 4.7uF 0.001uF 47uF
20.00% 10% 20.00% 10% 20.00%
10V 50V 50V 50V 10V
C155 C156 C157 C162 C203
1-126-926-11 1-104-665-11 1-163-021-91 1-164-489-11 1-126-957-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT
1000uF 100uF 0.01uF 0.22uF 0.22uF
20.00% 20.00% 10.00% 10.00% 20.00%
10V 10V 50V 16V 50V
C251 C252 C253 C254 C255
1-162-964-11 1-126-963-11 1-163-009-11 1-104-664-11 1-126-926-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT
0.001uF 4.7uF 0.001uF 47uF 1000uF
10% 20.00% 10% 20.00% 20.00%
50V 50V 50V 10V 10V
C256 C257 C262 C301 C302
1-104-665-11 1-163-021-91 1-164-489-11 1-162-970-11 1-135-181-21
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP
100uF 0.01uF 0.22uF 0.01uF 4.7uF
20.00% 10.00% 10.00% 10% 20%
10V 50V 16V 25V 6.3V
C351 C352 C353 C355 C356
1-162-970-11 1-164-227-11 1-104-664-11 1-126-960-11 1-163-009-11
CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP
0.01uF 0.022uF 47uF 1uF 0.001uF
10% 10% 20.00% 20.00% 10%
25V 25V 10V 50V 50V
C401 C402 C403 C404 C405
1-163-021-91 1-104-665-11 1-107-826-11 1-107-826-11 1-107-826-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 100uF 0.1uF 0.1uF 0.1uF
10.00% 20.00% 10.00% 10.00% 10.00%
50V 10V 16V 16V 16V
C406 C407 C408 C409 C410
1-107-826-11 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 100PF 100PF 100PF 100PF
10.00% 5% 5% 5% 5%
16V 50V 50V 50V 50V
C411 C412 C415 C417 C419
1-163-021-91 1-104-665-11 1-162-970-11 1-164-227-11 1-162-970-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 100uF 0.01uF 0.022uF 0.01uF
10.00% 20.00% 10% 10% 10%
50V 10V 25V 25V 25V
C422 C423 C424 C425 C426
1-162-970-11 1-162-970-11 1-162-970-11 1-163-251-11 1-163-251-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.01uF 100PF 100PF
10% 10% 10% 5.00% 5.00%
25V 25V 25V 50V 50V
< ANTENNA > ANT1
1-501-907-21 ANTENNA, FM WIRE < FILTER >
BPF1
1-235-171-00 FILTER, BAND PASS < CAPACITOR >
C1 C2 C3 C4 C8
1-163-141-00 1-163-141-00 1-163-091-00 1-163-220-11 1-163-021-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 0.001uF 8PF 3PF 0.01uF
5% 5%
50V 50V 50V 0.25PF 50V 10.00% 50V
C9 C10 C11 C12 C15
1-163-131-00 1-163-235-11 1-163-227-11 1-163-021-91 1-104-665-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
390PF 22PF 10PF 0.01uF 100uF
5% 5.00% 0.50PF 10.00% 20.00%
50V 50V 50V 50V 10V
C16 C17 C18 C19 C20
1-163-021-91 1-126-961-11 1-104-665-11 1-107-823-11 1-126-963-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT
0.01uF 2.2uF 100uF 0.47uF 4.7uF
10.00% 20.00% 20.00% 10.00% 20.00%
50V 50V 10V 16V 50V
C21 C22 C23 C24 C25
1-163-251-11 1-163-021-91 1-126-963-11 1-109-982-11 1-104-664-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
100PF 0.01uF 4.7uF 1uF 47uF
5.00% 10.00% 20.00% 10.00% 20.00%
50V 50V 50V 10V 16V
C26 C27 C28 C30 C32
1-163-021-91 1-104-664-11 1-162-970-11 1-162-970-11 1-163-021-91
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 47uF 0.01uF 0.01uF 0.01uF
10.00% 20.00% 10% 10% 10.00%
50V 16V 25V 25V 50V
C33 C34 C51 C52 C53
1-109-982-11 1-163-251-11 1-126-964-11 1-162-964-11 1-135-181-21
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP TANTALUM CHIP
1uF 100PF 10uF 0.001uF 4.7uF
10.00% 5.00% 20.00% 10% 20%
10V 50V 50V 50V 6.3V
— 33 —
MAIN Ref. No.
Part No.
Description
Part No.
Description
C427 C428 C433 C434 C435
1-163-251-11 1-162-964-11 1-163-227-11 1-163-227-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 0.001uF 10PF 10PF 0.01uF
5.00% 10% 0.50PF 0.50PF 10%
50V 50V 50V 50V 25V
Remarks
Ref. No. C553 C554 C555 C556 C557
1-163-251-11 1-163-251-11 1-164-315-11 1-163-251-11 1-164-227-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 470PF 100PF 0.022uF
5.00% 5.00% 5.00% 5.00% 10%
50V 50V 50V 50V 25V
C436 C437 C438 C442 C444
1-104-665-11 1-163-237-11 1-163-237-11 1-164-227-11 1-163-021-91
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100uF 27PF 27PF 0.022uF 0.01uF
20.00% 5.00% 5.00% 10% 10.00%
10V 50V 50V 25V 50V
C558 C559 C560 C561 C562
1-107-823-11 1-104-664-11 1-164-315-11 1-164-230-11 1-115-467-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.47uF 47uF 470PF 220PF 0.22uF
10.00% 20.00% 5.00% 5.00% 10.00%
16V 10V 50V 50V 10V
C445 C446 C447 C448 C449
1-164-004-11 1-126-935-11 1-126-935-11 1-162-966-11 1-162-966-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP
0.1uF 470uF 470uF 0.0022uF 0.0022uF
10% 20.00% 20.00% 10% 10%
25V 6.3V 6.3V 50V 50V
C563 C564 C565 C566 C567
1-162-970-11 1-162-970-11 1-162-927-11 1-104-664-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.01uF 0.01uF 100PF 47uF 0.01uF
10% 10% 5% 20.00% 10%
25V 25V 50V 10V 25V
C450 C451 C452 C453 C454
1-162-966-11 1-162-966-11 1-162-966-11 1-162-966-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0022uF 0.0022uF 0.0022uF 0.0022uF 0.01uF
10% 10% 10% 10% 10%
50V 50V 50V 50V 25V
C568 C569 C570 C571 C573
1-162-970-11 1-162-970-11 1-115-412-11 1-164-217-11 1-163-021-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 680PF 150PF 0.01uF
10% 10% 5.00% 5.00% 10.00%
25V 25V 25V 50V 50V
C455 C456 C457 C501 C502
1-162-966-11 1-162-966-11 1-162-966-11 1-107-826-11 1-164-677-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0022uF 0.0022uF 0.0022uF 0.1uF 0.033uF
10% 10% 10% 10.00% 10.00%
50V 50V 50V 16V 16V
C574 C575 C577 C578 C579
1-163-227-11 1-163-227-11 1-164-217-11 1-115-412-11 1-163-021-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10PF 10PF 150PF 680PF 0.01uF
0.50PF 0.50PF 5.00% 5.00% 10.00%
50V 50V 50V 25V 50V
C503 C504 C505 C506 C507
1-162-966-11 1-107-826-11 1-107-826-11 1-107-826-11 1-135-259-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP
0.0022uF 0.1uF 0.1uF 0.1uF 10uF
10% 10.00% 10.00% 10.00% 20.00%
50V 16V 16V 16V 6.3V
C580 C581 C582 C583 C584
1-126-935-11 1-162-970-11 1-107-826-11 1-162-964-11 1-104-664-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
470uF 0.01uF 0.1uF 0.001uF 47uF
20.00% 10% 10.00% 10% 20.00%
6.3V 25V 16V 50V 10V
C508 C509 C510 C511 C512
1-164-677-11 1-163-024-00 1-162-915-11 1-126-962-11 1-164-344-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.033uF 0.018uF 10PF 3.3uF 0.068uF
10.00% 10.00% 0.5PF 20.00% 10.00%
16V 50V 50V 50V 25V
C586 C587 C588 C589 C590
1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 100PF 100PF 100PF
5% 5% 5% 5% 5%
50V 50V 50V 50V 50V
C513 C514 C515 C516 C517
1-162-923-11 1-163-021-91 1-104-664-11 1-162-970-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
47PF 0.01uF 47uF 0.01uF 100PF
5% 10.00% 20.00% 10% 5%
50V 50V 10V 25V 50V
C591 C592 C593 C595 C596
1-162-923-11 1-162-970-11 1-164-245-11 1-104-665-11 1-135-181-21
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT TANTALUM CHIP
47PF 0.01uF 0.015uF 100uF 4.7uF
5% 10% 10.00% 20.00% 20%
50V 25V 25V 10V 6.3V
C518 C519 C520 C521 C522
1-164-677-11 1-162-970-11 1-162-970-11 1-104-664-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.033uF 0.01uF 0.01uF 47uF 0.01uF
10.00% 10% 10% 20.00% 10%
16V 25V 25V 10V 25V
C597 C599 C901 C902 C903
1-163-021-91 1-126-925-11 1-163-021-91 1-163-021-91 1-163-021-91
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 470uF 0.01uF 0.01uF 0.01uF
10.00% 20.00% 10.00% 10.00% 10.00%
50V 10V 50V 50V 50V
C523 C524 C525 C526 C527
1-162-970-11 1-128-551-11 1-162-915-11 1-104-664-11 1-163-009-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP
0.01uF 22uF 10PF 47uF 0.001uF
10% 20.00% 0.5PF 20.00% 10%
25V 25V 50V 10V 50V
C904 C905 C906 C907 C908
1-164-004-11 1-164-004-11 1-164-004-11 1-164-004-11 1-126-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.1uF 0.1uF 0.1uF 0.1uF 10uF
10% 10% 10% 10% 20.00%
25V 25V 25V 25V 50V
C528 C529 C530 C531 C532
1-165-176-11 1-162-969-11 1-163-021-91 1-163-017-00 1-163-021-91
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.047uF 0.0068uF 0.01uF 0.0047uF 0.01uF
10.00% 10% 10.00% 5% 10.00%
16V 25V 50V 50V 50V
C909 C910 C911 C912 C913
1-126-959-11 1-126-947-11 1-163-021-91 1-128-547-11 1-163-021-91
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
0.47uF 47uF 0.01uF 6800uF 0.01uF
20.00% 20.00% 10.00% 20.00% 10.00%
50V 35V 50V 16V 50V
C533 C534 C535 C551 C552
1-104-664-11 1-163-037-11 1-107-826-11 1-163-251-11 1-163-251-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
47uF 0.022uF 0.1uF 100PF 100PF
20.00% 10% 10.00% 5.00% 5.00%
10V 25V 16V 50V 50V
C914 C915 C916 C917 C918
1-126-934-11 1-126-935-11 1-163-021-91 1-163-021-91 1-126-934-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT
220uF 470uF 0.01uF 0.01uF 220uF
20.00% 20.00% 10.00% 10.00% 20.00%
10V 6.3V 50V 50V 10V
— 34 —
Remarks
MAIN Ref. No. C919 C920
Part No.
Description
1-126-935-11 ELECT 1-163-021-91 CERAMIC CHIP
Remarks 470uF 0.01uF
Ref. No.
Part No.
Description
Remarks
< HOLDER >
20.00% 6.3V 10.00% 50V * KH901
1-573-287-11 HOLDER, CABLE 2P
< FILTER > < COIL > CF1 * CF2 CF3
1-760-238-11 FILTER, CERAMIC 1-577-319-11 FILTER, CERAMIC 1-760-238-11 FILTER, CERAMIC < CONNECTOR >
* * * *
CN351 CN401 CN402 CN403 CN501
* CN502
1-564-706-11 1-564-711-11 1-564-713-11 1-564-704-11 1-770-168-11
PIN, CONNECTOR (SMALL TYPE) 4P PIN, CONNECTOR (SMALL TYPE) 9P PIN, CONNECTOR (SMALL TYPE)11P PIN, CONNECTOR (SMALL TYPE) 2P CONNECTOR,FFC(LIF(NON-ZIF))16P
L1 L2 L3 L4 L401
1-406-545-11 1-416-459-11 1-402-616-11 1-406-485-11 1-216-295-91
COIL, AIR-CORE COIL, AIR-CORE ANTENNA, FERRITE-ROD (MW) COOL (OSC) SHORT 0
L402 L404 L405 L551 L552
1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
L553
1-216-295-91 SHORT
0
1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P < TRIMMER > < LIQUID CRYSTAL DISPLAY >
CT1 CT2
1-141-601-21 CAP, ADJ 1-141-601-21 CAP, ADJ
LCD401 1-804-008-11 DISPLAY PANEL LIQUID CRYSTAL < TRANSISTOR >
< DIODE > D2 D3 D4 D101 D102
8-713-100-12 8-713-100-12 8-719-072-59 8-719-988-61 8-719-988-61
DIODE DIODE DIODE DIODE DIODE
1T362 1T362 SVC347S-TL 1SS355TE-17 1SS355TE-17
Q5 Q51 Q52 Q101 Q102
8-729-027-31 8-729-120-28 8-729-120-28 8-729-141-75 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTA124EKA-T146 2SC1623-L5L6 2SC1623-L5L6 2SD596DV345 2SC1623-L5L6
D201 D301 D401 D501 D551
8-719-988-61 8-719-988-61 8-719-988-61 8-719-800-76 8-719-988-61
DIODE DIODE DIODE DIODE DIODE
1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS226 1SS355TE-17
Q103 Q201 Q202 Q203 Q301
8-729-120-28 8-729-141-75 8-729-120-28 8-729-120-28 8-729-049-50
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC1623-L5L6 2SD596DV345 2SC1623-L5L6 2SC1623-L5L6 2SB1424-T100-R
D552 D901 D902 D903 D904
8-719-800-76 8-719-988-61 8-719-988-61 8-719-988-61 8-719-031-85
DIODE DIODE DIODE DIODE DIODE
1SS226 (AEP,AUS) 1SS355TE-17 1SS355TE-17 1SS355TE-17 1N4002L
Q302 Q351 Q352 Q353 Q354
8-729-027-31 8-729-120-28 8-729-027-31 8-729-031-11 8-729-031-11
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTA124EKA-T146 2SC1623-L5L6 DTA124EKA-T146 2SD2537-T100VW 2SD2537-T100VW
D905 D906 D907 D908 D909
8-719-031-85 8-719-031-85 8-719-031-85 8-719-069-55 8-719-978-33
DIODE DIODE DIODE DIODE DIODE
1N4002L 1N4002L 1N4002L UDZS-TE17-5.6B UDZS-TE17-6.8B
Q501 Q901 Q902
8-729-801-84 TRANSISTOR 8-729-021-82 TRANSISTOR 8-729-021-82 TRANSISTOR
D910
8-719-988-61 DIODE 1SS355TE-17 < FERRITE BEAD >
FB501 FB502
1-216-295-91 SHORT 1-216-295-91 SHORT
0 0
2SB1013-4 2SD2396K 2SD2396K
< RESISTOR > R1 R2 R3
1-216-097-91 RES-CHIP 1-216-097-91 RES-CHIP 1-216-057-00 METAL CHIP
100K 100K 2.2K
5% 5% 5%
R3
1-216-065-91 RES-CHIP
4.7K
5%
R4
1-216-821-11 METAL CHIP
1K
5%
1/10W 1/10W 1/10W (US,CND) 1/10W (AEP,AUS) 1/16W
R5 R7 R11 R12 R13
1-216-073-00 1-216-121-91 1-216-025-91 1-216-073-00 1-216-105-91
METAL CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP
10K 1M 100 10K 220K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R14 R15 R16 R17 R19
1-216-057-00 1-216-817-11 1-216-057-00 1-216-831-11 1-216-831-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 470 2.2K 6.8K 6.8K
5% 5% 5% 5% 5%
1/10W 1/16W 1/10W 1/16W 1/16W
< IC > IC1 IC51 IC351 IC401 IC402
8-752-062-48 8-759-188-85 8-759-426-51 8-759-686-96 8-759-165-89
IC IC IC IC IC
CXA1238M-T6 BU2614FS BA5417 uPD789407AGK-A21-9EU PST600L-T
IC501 IC551 IC591
8-752-082-14 IC CXA1992BR 8-752-384-13 IC CXD2589Q 8-759-473-42 IC BA6898FP
— 35 —
MAIN Ref. No.
Part No.
Description
Part No.
Description
R23 R25 R26 R27 R52
1-216-105-91 1-216-803-11 1-216-037-00 1-216-025-91 1-216-817-11
RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP
220K 33 330 100 470
5% 5% 5% 5% 5%
Remarks 1/10W 1/16W 1/10W 1/10W 1/16W
Ref. No. R357 R401 R403 R404 R405
1-216-025-91 1-216-849-11 1-216-847-11 1-216-847-11 1-216-847-11
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 220K 150K 150K 150K
5% 5% 5% 5% 5%
1/10W 1/16W 1/16W 1/16W 1/16W
R53 R54 R55 R56 R59
1-216-049-91 1-216-821-11 1-216-821-11 1-216-821-11 1-216-829-11
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 4.7K
5% 5% 5% 5% 5%
1/10W 1/16W 1/16W 1/16W 1/16W (AEP,AUS)
R406 R407 R408 R409 R410
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R60 R61 R62 R63 R64
1-216-073-00 1-216-073-00 1-216-073-00 1-216-097-91 1-216-073-00
METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP
10K 10K 10K 100K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R411 R412 R413 R414 R415
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R65 R67 R101 R103 R104
1-216-001-00 1-216-821-11 1-216-049-91 1-216-295-91 1-216-049-91
METAL CHIP METAL CHIP RES-CHIP SHORT RES-CHIP
10 1K 1K 0 1K
5% 5% 5%
1/10W 1/16W 1/10W
R416 R417 R418 R419 R420
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
5%
1/10W
R105 R106 R108 R109 R151
1-216-833-11 1-216-833-11 1-216-049-91 1-216-025-91 1-216-837-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP
10K 10K 1K 100 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/10W 1/10W 1/16W
R421 R422 R423 R424 R425
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R152 R153 R154 R155 R158
1-216-073-00 1-216-113-00 1-216-027-00 1-216-298-00 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 470K 120 2.2 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/16W
R426 R427 R428 R429 R430
1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
10K 10K 10K 10K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R159 R162 R163 R201 R203
1-216-049-91 1-216-057-00 1-216-065-91 1-216-049-91 1-216-295-91
RES-CHIP METAL CHIP RES-CHIP RES-CHIP SHORT
1K 2.2K 4.7K 1K 0
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R431 R432 R433 R434 R435
1-216-837-11 1-216-841-11 1-216-837-11 1-216-841-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 47K 22K 47K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R204 R205 R206 R251 R252
1-216-049-91 1-216-833-11 1-216-833-11 1-216-837-11 1-216-073-00
RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP
1K 10K 10K 22K 10K
5% 5% 5% 5% 5%
1/10W 1/16W 1/16W 1/16W 1/10W
R436 R437 R438 R439 R440
1-216-841-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 1K 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R253 R254 R255 R258 R259
1-216-113-00 1-216-027-00 1-216-298-00 1-216-837-11 1-216-049-91
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
470K 120 2.2 22K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/16W 1/10W
R441 R442 R443 R444 R445
1-216-841-11 1-216-837-11 1-216-841-11 1-216-837-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 22K 47K 22K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R262 R263 R301 R302 R303
1-216-057-00 1-216-065-91 1-216-841-11 1-216-817-11 1-216-025-91
METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP
2.2K 4.7K 47K 470 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/16W 1/16W 1/10W
R446 R447 R448 R449 R450
1-216-837-11 1-216-841-11 1-216-837-11 1-216-841-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 47K 22K 47K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R451
1-216-821-11 METAL CHIP
1K
5%
R305 R351 R353 R355 R356
1-216-089-91 1-216-295-91 1-216-065-91 1-216-049-91 1-216-025-91
RES-CHIP SHORT RES-CHIP RES-CHIP RES-CHIP
47K 0 4.7K 1K 100
5%
1/10W R451
1-216-841-11 METAL CHIP
47K
5%
5% 5% 5%
1/10W 1/10W 1/10W
R452 R453 R454
1-216-837-11 METAL CHIP 1-216-833-11 RES-CHIP 1-216-849-11 METAL CHIP
22K 10K 220K
5% 5% 5%
1/16W (US,CND) 1/16W (AEP,AUS) 1/16W 1/16W 1/16W
— 36 —
Remarks
MAIN Ref. No.
Part No.
Description
Part No.
Description
R455 R456 R457 R458 R459
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
1K 1K 1K 1K 10K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R521 R522 R523 R524 R525
1-216-829-11 1-216-001-00 1-216-844-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 10 82K 100K 100K
5% 5% 5% 5% 5%
1/16W 1/10W 1/16W 1/16W 1/16W
R460 R461 R462 R463 R464
1-216-821-11 1-216-821-11 1-216-809-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 100 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R526 R527 R528 R529 R530
1-216-845-11 1-216-845-11 1-216-844-11 1-216-851-11 1-216-847-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 82K 330K 150K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R465 R466 R467 R468 R469
1-216-809-11 1-216-809-11 1-216-049-91 1-216-049-91 1-216-049-91
METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP
100 100 1K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/10W 1/10W 1/10W
R531 R532 R551 R552 R553
1-216-101-00 1-216-105-91 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP
150K 220K 1K 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/16W 1/16W 1/16W
R470 R475 R476 R477 R478
1-216-821-11 1-216-295-91 1-216-049-91 1-216-049-91 1-216-049-91
METAL CHIP SHORT RES-CHIP RES-CHIP RES-CHIP
1K 0 1K 1K 1K
5%
1/16W
5% 5% 5%
1/10W 1/10W 1/10W
R554 R555 R556 R557 R558
1-216-821-11 1-216-841-11 1-216-821-11 1-216-841-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 47K 1K 47K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R479 R481
1-216-833-11 RES-CHIP 1-216-833-11 RES-CHIP
10K 10K
5% 5%
R482
1-216-833-11 RES-CHIP
10K
R559 R560 R561 R562 R563
1-216-827-11 1-216-821-11 1-216-833-11 1-216-857-11 1-216-849-11
METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP
3.3K 1K 10K 1M 220K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R483
1-216-833-11 RES-CHIP
10K
R484
1-216-833-11 RES-CHIP
10K
R486 R487 R488 R491 R492
1-216-841-11 1-216-837-11 1-216-113-00 1-216-841-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 22K 470K 47K 47K
5% 5% 5% 5% 5%
1/16W 1/16W 1/10W 1/16W 1/16W
R564 R565 R566 R568 R569
1-216-833-11 1-216-821-11 1-216-833-11 1-216-834-11 1-216-834-11
RES-CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP
10K 1K 10K 12K 12K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
47K 1K 1K 47K 7.5K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
METAL CHIP RES-CHIP SHORT METAL CHIP METAL CHIP
6.8K 22 0 6.8K 12K
1/16W 1/10W
1-216-841-11 1-216-821-11 1-216-821-11 1-216-841-11 1-218-344-11
1-216-831-11 1-216-009-00 1-216-295-91 1-216-831-11 1-216-834-11
5% 5%
R493 R494 R495 R496 R501
R570 R571 R572 R574 R575
5% 5%
1/16W 1/16W
R502 R503 R504 R505 R506
1-216-833-91 1-216-832-11 1-216-855-11 1-216-114-00 1-216-843-11
RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP
10K 8.2K 680K 510K 68K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/10W 1/16W
R576 R578 R579 R580 R581
1-216-834-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-821-11
METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP
12K 10K 10K 1K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R582 R583 R584 R591
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 1K
5% 5% 5% 5%
R507 R508 R509 R510 R511
1-216-295-91 1-216-847-11 1-216-089-91 1-216-834-11 1-216-081-00
SHORT METAL CHIP RES-CHIP METAL CHIP METAL CHIP
0 150K 47K 12K 22K
5% 5% 5% 5%
1/16W 1/10W 1/16W 1/10W
R591
1-216-817-11 METAL CHIP
470
5%
1/16W 1/16W 1/16W 1/16W (US,CND) 1/16W (AEP,AUS)
R512 R513
1-216-848-11 METAL CHIP 1-216-846-11 METAL CHIP
180K 120K
5% 5%
1-216-847-11 1-216-837-11 1-216-839-11 1-216-839-11 1-216-834-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
150K 22K 33K 33K 12K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R513
1-216-847-11 METAL CHIP
150K
5%
R514 R515
1-216-833-11 RES-CHIP 1-216-073-00 METAL CHIP
10K 10K
5% 5%
1/16W 1/16W (US,CND) 1/16W (AEP,AUS) 1/16W 1/10W
R592 R593 R594 R595 R596
R516 R517 R518 R519 R520
1-216-833-11 1-216-850-11 1-216-839-11 1-216-835-11 1-216-121-91
10K 270K 33K 15K 1M
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/10W
R702 R705 R706 R707 R708
1-216-295-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 1K 1K 1K 1K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
RES-CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
Remarks
1/16W 1/16W (US,CND) 5% 1/16W (AEP,AUS) 5% 1/16W (US,CND,AUS) 5% 1/16W (AEP)
Ref. No.
— 37 —
Remarks
ICF-CD823 MAIN
Ver 1.1 2001. 04
MOTOR (6P)
TRANSFORMER
Ref. No.
Part No.
Description
R709 R901 R902 R903 0 R904
1-216-049-91 1-216-025-91 1-216-097-91 1-216-097-91 1-219-149-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP FUSIBLE
1K 100 100K 100K 1
5% 5% 5% 5% 5%
Remarks 1/10W 1/10W 1/10W 1/10W 1/4W
R905 R906 0 R907 R908
1-216-041-00 1-216-049-91 1-219-149-11 1-216-041-00
METAL CHIP RES-CHIP FUSIBLE METAL CHIP
470 1K 1 470
5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W
Ref. No.
Part No.
LF901
1-424-150-11 TRANSFORMER, LINE FILTER < TRANSFORMER >
0 T901 0 T901
1-435-578-31 TRANSFORMER, POWER (US,CND) 1-435-579-31 TRANSFORMER, POWER (AEP,AUS)
************************************************************ MISCELLANEOUS **************
1-241-765-11 RES, ADJ, CARBON 22K 1-225-764-11 RES, VAR, CARBON 20K/20K (VOLUME) < TRANSFORMER >
T1
1-404-790-11 TRANSFORMER, IF < VIBRATOR >
X51 1-567-769-11 VIBRATOR, CRYSTAL 75kHz X401 1-781-357-11 VIBRATOR, CERAMIC 4.19MHz X402 1-567-098-41 VIBRATOR, CRYSTAL 32kHz X501 1-577-253-11 VIBRATOR, CERAMIC 16.934MHz ************************************************************
08 08 08 12 68
1-555-795-00 1-790-431-11 1-790-757-11 1-452-732-11 1-777-955-11
CORD, POWER (AEP) CORD, POWER (AUS) CORD, POWER (US,CND) MAGNET WIRE (FLAT TYPE) (16 CORE)
! 101 S501 M571 M572 SP101
8-848-483-05 1-692-960-11 X-2625-769-1 X-2626-202-1 1-504-460-11
OPTICAL PICK-UP KSS-213CDM SWITCH, PUSH (1 KEY) (DOOR SW) GEAR ASSY (MB), MOTOR (SLED) CHASSIS ASSY (MB), (RP) (SPINDLE) SPEAKER (7.7cm) (L-CH)
SP201 1-504-460-11 SPEAKER (7.7cm) (R-CH) ************************************************************
1-639-678-12 MOTOR (6P) BOARD ****************
*
Remarks
< LINE FILTER >
< VARIABLE RESISTOR > RV1 RV301
Description
ACCESSORIES & PACKING MATERIALS ********************************
< CONNECTOR > CNP502 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P < SWITCH > S570 1-572-085-11 SWITCH, LEAF ************************************************************ *
1-678-392-11 TRANSFORMER BOARD *******************
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
< CONNECTOR > * CN901
3-046-170-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, GERMAN, DUTCH)(CND,AEP,AUS) 3-046-170-21 MANUAL, INSTRUCTION (ENGLISH) (US) 3-046-170-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH, ITALIAN, PORTUGUESE)(AEP) 3-046-170-41 MANUAL, INSTRUCTION (ENGLISH, SWEDISH, DANISH, FINNISH)(AEP)
1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
— 38 —
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
ICF-CD823
MEMO
39
ICF-CD823
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver.
Date
Description of Revision
1.1
2001.04
Correction of exploded views.
1.0
2000.05
New
(RPC-01003)
